From 1245fbd2a8d60bab7b16b8a1d3c0122fee72f53f Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Wed, 5 Jun 2013 00:57:38 +0200 Subject: Nuke trailing whitespace. Signed-off-by: Ralf Baechle --- hdlcutil/sethdlc.8 | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) (limited to 'hdlcutil/sethdlc.8') diff --git a/hdlcutil/sethdlc.8 b/hdlcutil/sethdlc.8 index 0d784f3..bfbf8a2 100644 --- a/hdlcutil/sethdlc.8 +++ b/hdlcutil/sethdlc.8 @@ -66,7 +66,7 @@ instructs the driver to send a calibration pattern for .I cal seconds. -Without the +Without the .B \-p, .B \-a and @@ -76,7 +76,7 @@ option, will stay in the foreground and display received packets. The AX.25 header and eventually a FlexNet compressed header are decoded. CTRL-C terminates .B sethdlc. -Specifying additional options, +Specifying additional options, .B sethdlc may display additional information. @@ -87,7 +87,7 @@ accepts the following options: .TP .B \-b -Trace the bits at the output of the demodulator, after RX clock recovery. +Trace the bits at the output of the demodulator, after RX clock recovery. This option is only available if \fBsethdlc\fP and the soundcard modem kernel driver is compiled with debugging support on. This is useful for driver debugging. @@ -110,7 +110,7 @@ interrogated. It will usually have the following form: .B \-s Trace the bits at the demodulator output, \fIbefore\fP the RX clock recovery, to stdout. This option is only available the modem driver -is compiled with debugging support on. It may not be available on some modem, such +is compiled with debugging support on. It may not be available on some modem, such as the \fIpar96\fP. .SH PARAMETERS @@ -161,14 +161,14 @@ The .B seriobase parameter optionally sets the address of a serial port, where the driver will output a PTT signal at the TxD and RTS pins, and a DCD -signal at the DTR pin. As Baycom modems do have their own PTT pin, this +signal at the DTR pin. As Baycom modems do have their own PTT pin, this parameter is not used by the Baycom modem driver. The .B pariobase parameter optionally sets the address of a LPT port where the driver will output a PTT signal on the DATA0 line and a DCD signal -on the DATA1 line. As Baycom modems do have their own PTT pin, this +on the DATA1 line. As Baycom modems do have their own PTT pin, this parameter is not used by the Baycom modem driver. The @@ -198,7 +198,7 @@ time to actually clock the last bits out to the transmitter. The .B slottime parameter specifies how often the channel access algorithm is executed. -Unlike \fIkissparms\fP, the unit is \fItens of ms\fP. Unless you have very +Unlike \fIkissparms\fP, the unit is \fItens of ms\fP. Unless you have very specific requirements, set this to 100ms (i.e. 10). The @@ -220,7 +220,7 @@ sets the modem to half duplex mode. .SH CONSIDERATIONS OF CONFIGURING BAYCOM PORTS It is important to note that sethdlc merely tells the Linux kernel where it should expect to find the I/O port and IRQ lines of a -particular serial port. It does +particular serial port. It does .I not configure the hardware to use a particular I/O port. In order to do that, you will need to physically -- cgit v1.2.3