diff options
Diffstat (limited to 'include/asm-m68knommu/MC68VZ328.h')
| -rw-r--r-- | include/asm-m68knommu/MC68VZ328.h | 1349 |
1 files changed, 0 insertions, 1349 deletions
diff --git a/include/asm-m68knommu/MC68VZ328.h b/include/asm-m68knommu/MC68VZ328.h deleted file mode 100644 index 2b9bf626a0a5..000000000000 --- a/include/asm-m68knommu/MC68VZ328.h +++ /dev/null @@ -1,1349 +0,0 @@ - -/* include/asm-m68knommu/MC68VZ328.h: 'VZ328 control registers - * - * Copyright (c) 2000-2001 Lineo Inc. <www.lineo.com> - * Copyright (c) 2000-2001 Lineo Canada Corp. <www.lineo.ca> - * Copyright (C) 1999 Vladimir Gurevich <vgurevic@cisco.com> - * Bare & Hare Software, Inc. - * Based on include/asm-m68knommu/MC68332.h - * Copyright (C) 1998 Kenneth Albanowski <kjahds@kjahds.com>, - * The Silver Hammer Group, Ltd. - * - * M68VZ328 fixes by Evan Stawnyczy <evan@lineo.com> - * vz multiport fixes by Michael Leslie <mleslie@lineo.com> - */ - -#ifndef _MC68VZ328_H_ -#define _MC68VZ328_H_ - -#define BYTE_REF(addr) (*((volatile unsigned char*)addr)) -#define WORD_REF(addr) (*((volatile unsigned short*)addr)) -#define LONG_REF(addr) (*((volatile unsigned long*)addr)) - -#define PUT_FIELD(field, val) (((val) << field##_SHIFT) & field##_MASK) -#define GET_FIELD(reg, field) (((reg) & field##_MASK) >> field##_SHIFT) - -/********** - * - * 0xFFFFF0xx -- System Control - * - **********/ - -/* - * System Control Register (SCR) - */ -#define SCR_ADDR 0xfffff000 -#define SCR BYTE_REF(SCR_ADDR) - -#define SCR_WDTH8 0x01 /* 8-Bit Width Select */ -#define SCR_DMAP 0x04 /* Double Map */ -#define SCR_SO 0x08 /* Supervisor Only */ -#define SCR_BETEN 0x10 /* Bus-Error Time-Out Enable */ -#define SCR_PRV 0x20 /* Privilege Violation */ -#define SCR_WPV 0x40 /* Write Protect Violation */ -#define SCR_BETO 0x80 /* Bus-Error TimeOut */ - -/* - * Silicon ID Register (Mask Revision Register (MRR) for '328 Compatibility) - */ -#define MRR_ADDR 0xfffff004 -#define MRR LONG_REF(MRR_ADDR) - -/********** - * - * 0xFFFFF1xx -- Chip-Select logic - * - **********/ - -/* - * Chip Select Group Base Registers - */ -#define CSGBA_ADDR 0xfffff100 -#define CSGBB_ADDR 0xfffff102 - -#define CSGBC_ADDR 0xfffff104 -#define CSGBD_ADDR 0xfffff106 - -#define CSGBA WORD_REF(CSGBA_ADDR) -#define CSGBB WORD_REF(CSGBB_ADDR) -#define CSGBC WORD_REF(CSGBC_ADDR) -#define CSGBD WORD_REF(CSGBD_ADDR) - -/* - * Chip Select Registers - */ -#define CSA_ADDR 0xfffff110 -#define CSB_ADDR 0xfffff112 -#define CSC_ADDR 0xfffff114 -#define CSD_ADDR 0xfffff116 - -#define CSA WORD_REF(CSA_ADDR) -#define CSB WORD_REF(CSB_ADDR) -#define CSC WORD_REF(CSC_ADDR) -#define CSD WORD_REF(CSD_ADDR) - -#define CSA_EN 0x0001 /* Chip-Select Enable */ -#define CSA_SIZ_MASK 0x000e /* Chip-Select Size */ -#define CSA_SIZ_SHIFT 1 -#define CSA_WS_MASK 0x0070 /* Wait State */ -#define CSA_WS_SHIFT 4 -#define CSA_BSW 0x0080 /* Data Bus Width */ -#define CSA_FLASH 0x0100 /* FLASH Memory Support */ -#define CSA_RO 0x8000 /* Read-Only */ - -#define CSB_EN 0x0001 /* Chip-Select Enable */ -#define CSB_SIZ_MASK 0x000e /* Chip-Select Size */ -#define CSB_SIZ_SHIFT 1 -#define CSB_WS_MASK 0x0070 /* Wait State */ -#define CSB_WS_SHIFT 4 -#define CSB_BSW 0x0080 /* Data Bus Width */ -#define CSB_FLASH 0x0100 /* FLASH Memory Support */ -#define CSB_UPSIZ_MASK 0x1800 /* Unprotected memory block size */ -#define CSB_UPSIZ_SHIFT 11 -#define CSB_ROP 0x2000 /* Readonly if protected */ -#define CSB_SOP 0x4000 /* Supervisor only if protected */ -#define CSB_RO 0x8000 /* Read-Only */ - -#define CSC_EN 0x0001 /* Chip-Select Enable */ -#define CSC_SIZ_MASK 0x000e /* Chip-Select Size */ -#define CSC_SIZ_SHIFT 1 -#define CSC_WS_MASK 0x0070 /* Wait State */ -#define CSC_WS_SHIFT 4 -#define CSC_BSW 0x0080 /* Data Bus Width */ -#define CSC_FLASH 0x0100 /* FLASH Memory Support */ -#define CSC_UPSIZ_MASK 0x1800 /* Unprotected memory block size */ -#define CSC_UPSIZ_SHIFT 11 -#define CSC_ROP 0x2000 /* Readonly if protected */ -#define CSC_SOP 0x4000 /* Supervisor only if protected */ -#define CSC_RO 0x8000 /* Read-Only */ - -#define CSD_EN 0x0001 /* Chip-Select Enable */ -#define CSD_SIZ_MASK 0x000e /* Chip-Select Size */ -#define CSD_SIZ_SHIFT 1 -#define CSD_WS_MASK 0x0070 /* Wait State */ -#define CSD_WS_SHIFT 4 -#define CSD_BSW 0x0080 /* Data Bus Width */ -#define CSD_FLASH 0x0100 /* FLASH Memory Support */ -#define CSD_DRAM 0x0200 /* Dram Selection */ -#define CSD_COMB 0x0400 /* Combining */ -#define CSD_UPSIZ_MASK 0x1800 /* Unprotected memory block size */ -#define CSD_UPSIZ_SHIFT 11 -#define CSD_ROP 0x2000 /* Readonly if protected */ -#define CSD_SOP 0x4000 /* Supervisor only if protected */ -#define CSD_RO 0x8000 /* Read-Only */ - -/* - * Emulation Chip-Select Register - */ -#define EMUCS_ADDR 0xfffff118 -#define EMUCS WORD_REF(EMUCS_ADDR) - -#define EMUCS_WS_MASK 0x0070 -#define EMUCS_WS_SHIFT 4 - -/********** - * - * 0xFFFFF2xx -- Phase Locked Loop (PLL) & Power Control - * - **********/ - -/* - * PLL Control Register - */ -#define PLLCR_ADDR 0xfffff200 -#define PLLCR WORD_REF(PLLCR_ADDR) - -#define PLLCR_DISPLL 0x0008 /* Disable PLL */ -#define PLLCR_CLKEN 0x0010 /* Clock (CLKO pin) enable */ -#define PLLCR_PRESC 0x0020 /* VCO prescaler */ -#define PLLCR_SYSCLK_SEL_MASK 0x0700 /* System Clock Selection */ -#define PLLCR_SYSCLK_SEL_SHIFT 8 -#define PLLCR_LCDCLK_SEL_MASK 0x3800 /* LCD Clock Selection */ -#define PLLCR_LCDCLK_SEL_SHIFT 11 - -/* '328-compatible definitions */ -#define PLLCR_PIXCLK_SEL_MASK PLLCR_LCDCLK_SEL_MASK -#define PLLCR_PIXCLK_SEL_SHIFT PLLCR_LCDCLK_SEL_SHIFT - -/* - * PLL Frequency Select Register - */ -#define PLLFSR_ADDR 0xfffff202 -#define PLLFSR WORD_REF(PLLFSR_ADDR) - -#define PLLFSR_PC_MASK 0x00ff /* P Count */ -#define PLLFSR_PC_SHIFT 0 -#define PLLFSR_QC_MASK 0x0f00 /* Q Count */ -#define PLLFSR_QC_SHIFT 8 -#define PLLFSR_PROT 0x4000 /* Protect P & Q */ -#define PLLFSR_CLK32 0x8000 /* Clock 32 (kHz) */ - -/* - * Power Control Register - */ -#define PCTRL_ADDR 0xfffff207 -#define PCTRL BYTE_REF(PCTRL_ADDR) - -#define PCTRL_WIDTH_MASK 0x1f /* CPU Clock bursts width */ -#define PCTRL_WIDTH_SHIFT 0 -#define PCTRL_PCEN 0x80 /* Power Control Enable */ - -/********** - * - * 0xFFFFF3xx -- Interrupt Controller - * - **********/ - -/* - * Interrupt Vector Register - */ -#define IVR_ADDR 0xfffff300 -#define IVR BYTE_REF(IVR_ADDR) - -#define IVR_VECTOR_MASK 0xF8 - -/* - * Interrupt control Register - */ -#define ICR_ADDR 0xfffff302 -#define ICR WORD_REF(ICR_ADDR) - -#define ICR_POL5 0x0080 /* Polarity Control for IRQ5 */ -#define ICR_ET6 0x0100 /* Edge Trigger Select for IRQ6 */ -#define ICR_ET3 0x0200 /* Edge Trigger Select for IRQ3 */ -#define ICR_ET2 0x0400 /* Edge Trigger Select for IRQ2 */ -#define ICR_ET1 0x0800 /* Edge Trigger Select for IRQ1 */ -#define ICR_POL6 0x1000 /* Polarity Control for IRQ6 */ -#define ICR_POL3 0x2000 /* Polarity Control for IRQ3 */ -#define ICR_POL2 0x4000 /* Polarity Control for IRQ2 */ -#define ICR_POL1 0x8000 /* Polarity Control for IRQ1 */ - -/* - * Interrupt Mask Register - */ -#define IMR_ADDR 0xfffff304 -#define IMR LONG_REF(IMR_ADDR) - -/* - * Define the names for bit positions first. This is useful for - * request_irq - */ -#define SPI2_IRQ_NUM 0 /* SPI 2 interrupt */ -#define TMR_IRQ_NUM 1 /* Timer 1 interrupt */ -#define UART1_IRQ_NUM 2 /* UART 1 interrupt */ -#define WDT_IRQ_NUM 3 /* Watchdog Timer interrupt */ -#define RTC_IRQ_NUM 4 /* RTC interrupt */ -#define TMR2_IRQ_NUM 5 /* Timer 2 interrupt */ -#define KB_IRQ_NUM 6 /* Keyboard Interrupt */ -#define PWM1_IRQ_NUM 7 /* Pulse-Width Modulator 1 int. */ -#define INT0_IRQ_NUM 8 /* External INT0 */ -#define INT1_IRQ_NUM 9 /* External INT1 */ -#define INT2_IRQ_NUM 10 /* External INT2 */ -#define INT3_IRQ_NUM 11 /* External INT3 */ -#define UART2_IRQ_NUM 12 /* UART 2 interrupt */ -#define PWM2_IRQ_NUM 13 /* Pulse-Width Modulator 1 int. */ -#define IRQ1_IRQ_NUM 16 /* IRQ1 */ -#define IRQ2_IRQ_NUM 17 /* IRQ2 */ -#define IRQ3_IRQ_NUM 18 /* IRQ3 */ -#define IRQ6_IRQ_NUM 19 /* IRQ6 */ -#define IRQ5_IRQ_NUM 20 /* IRQ5 */ -#define SPI1_IRQ_NUM 21 /* SPI 1 interrupt */ -#define SAM_IRQ_NUM 22 /* Sampling Timer for RTC */ -#define EMIQ_IRQ_NUM 23 /* Emulator Interrupt */ - -#define SPI_IRQ_NUM SPI2_IRQ_NUM - -/* '328-compatible definitions */ -#define SPIM_IRQ_NUM SPI_IRQ_NUM -#define TMR1_IRQ_NUM TMR_IRQ_NUM -#define UART_IRQ_NUM UART1_IRQ_NUM - -/* - * Here go the bitmasks themselves - */ -#define IMR_MSPI (1 << SPI_IRQ_NUM) /* Mask SPI interrupt */ -#define IMR_MTMR (1 << TMR_IRQ_NUM) /* Mask Timer interrupt */ -#define IMR_MUART (1 << UART_IRQ_NUM) /* Mask UART interrupt */ -#define IMR_MWDT (1 << WDT_IRQ_NUM) /* Mask Watchdog Timer interrupt */ -#define IMR_MRTC (1 << RTC_IRQ_NUM) /* Mask RTC interrupt */ -#define IMR_MKB (1 << KB_IRQ_NUM) /* Mask Keyboard Interrupt */ -#define IMR_MPWM (1 << PWM_IRQ_NUM) /* Mask Pulse-Width Modulator int. */ -#define IMR_MINT0 (1 << INT0_IRQ_NUM) /* Mask External INT0 */ -#define IMR_MINT1 (1 << INT1_IRQ_NUM) /* Mask External INT1 */ -#define IMR_MINT2 (1 << INT2_IRQ_NUM) /* Mask External INT2 */ -#define IMR_MINT3 (1 << INT3_IRQ_NUM) /* Mask External INT3 */ -#define IMR_MIRQ1 (1 << IRQ1_IRQ_NUM) /* Mask IRQ1 */ -#define IMR_MIRQ2 (1 << IRQ2_IRQ_NUM) /* Mask IRQ2 */ -#define IMR_MIRQ3 (1 << IRQ3_IRQ_NUM) /* Mask IRQ3 */ -#define IMR_MIRQ6 (1 << IRQ6_IRQ_NUM) /* Mask IRQ6 */ -#define IMR_MIRQ5 (1 << IRQ5_IRQ_NUM) /* Mask IRQ5 */ -#define IMR_MSAM (1 << SAM_IRQ_NUM) /* Mask Sampling Timer for RTC */ -#define IMR_MEMIQ (1 << EMIQ_IRQ_NUM) /* Mask Emulator Interrupt */ - -/* '328-compatible definitions */ -#define IMR_MSPIM IMR_MSPI -#define IMR_MTMR1 IMR_MTMR - -/* - * Interrupt Status Register - */ -#define ISR_ADDR 0xfffff30c -#define ISR LONG_REF(ISR_ADDR) - -#define ISR_SPI (1 << SPI_IRQ_NUM) /* SPI interrupt */ -#define ISR_TMR (1 << TMR_IRQ_NUM) /* Timer interrupt */ -#define ISR_UART (1 << UART_IRQ_NUM) /* UART interrupt */ -#define ISR_WDT (1 << WDT_IRQ_NUM) /* Watchdog Timer interrupt */ -#define ISR_RTC (1 << RTC_IRQ_NUM) /* RTC interrupt */ -#define ISR_KB (1 << KB_IRQ_NUM) /* Keyboard Interrupt */ -#define ISR_PWM (1 << PWM_IRQ_NUM) /* Pulse-Width Modulator interrupt */ -#define ISR_INT0 (1 << INT0_IRQ_NUM) /* External INT0 */ -#define ISR_INT1 (1 << INT1_IRQ_NUM) /* External INT1 */ -#define ISR_INT2 (1 << INT2_IRQ_NUM) /* External INT2 */ -#define ISR_INT3 (1 << INT3_IRQ_NUM) /* External INT3 */ -#define ISR_IRQ1 (1 << IRQ1_IRQ_NUM) /* IRQ1 */ -#define ISR_IRQ2 (1 << IRQ2_IRQ_NUM) /* IRQ2 */ -#define ISR_IRQ3 (1 << IRQ3_IRQ_NUM) /* IRQ3 */ -#define ISR_IRQ6 (1 << IRQ6_IRQ_NUM) /* IRQ6 */ -#define ISR_IRQ5 (1 << IRQ5_IRQ_NUM) /* IRQ5 */ -#define ISR_SAM (1 << SAM_IRQ_NUM) /* Sampling Timer for RTC */ -#define ISR_EMIQ (1 << EMIQ_IRQ_NUM) /* Emulator Interrupt */ - -/* '328-compatible definitions */ -#define ISR_SPIM ISR_SPI -#define ISR_TMR1 ISR_TMR - -/* - * Interrupt Pending Register - */ -#define IPR_ADDR 0xfffff30c -#define IPR LONG_REF(IPR_ADDR) - -#define IPR_SPI (1 << SPI_IRQ_NUM) /* SPI interrupt */ -#define IPR_TMR (1 << TMR_IRQ_NUM) /* Timer interrupt */ -#define IPR_UART (1 << UART_IRQ_NUM) /* UART interrupt */ -#define IPR_WDT (1 << WDT_IRQ_NUM) /* Watchdog Timer interrupt */ -#define IPR_RTC (1 << RTC_IRQ_NUM) /* RTC interrupt */ -#define IPR_KB (1 << KB_IRQ_NUM) /* Keyboard Interrupt */ -#define IPR_PWM (1 << PWM_IRQ_NUM) /* Pulse-Width Modulator interrupt */ -#define IPR_INT0 (1 << INT0_IRQ_NUM) /* External INT0 */ -#define IPR_INT1 (1 << INT1_IRQ_NUM) /* External INT1 */ -#define IPR_INT2 (1 << INT2_IRQ_NUM) /* External INT2 */ -#define IPR_INT3 (1 << INT3_IRQ_NUM) /* External INT3 */ -#define IPR_IRQ1 (1 << IRQ1_IRQ_NUM) /* IRQ1 */ -#define IPR_IRQ2 (1 << IRQ2_IRQ_NUM) /* IRQ2 */ -#define IPR_IRQ3 (1 << IRQ3_IRQ_NUM) /* IRQ3 */ -#define IPR_IRQ6 (1 << IRQ6_IRQ_NUM) /* IRQ6 */ -#define IPR_IRQ5 (1 << IRQ5_IRQ_NUM) /* IRQ5 */ -#define IPR_SAM (1 << SAM_IRQ_NUM) /* Sampling Timer for RTC */ -#define IPR_EMIQ (1 << EMIQ_IRQ_NUM) /* Emulator Interrupt */ - -/* '328-compatible definitions */ -#define IPR_SPIM IPR_SPI -#define IPR_TMR1 IPR_TMR - -/********** - * - * 0xFFFFF4xx -- Parallel Ports - * - **********/ - -/* - * Port A - */ -#define PADIR_ADDR 0xfffff400 /* Port A direction reg */ -#define PADATA_ADDR 0xfffff401 /* Port A data register */ -#define PAPUEN_ADDR 0xfffff402 /* Port A Pull-Up enable reg */ - -#define PADIR BYTE_REF(PADIR_ADDR) -#define PADATA BYTE_REF(PADATA_ADDR) -#define PAPUEN BYTE_REF(PAPUEN_ADDR) - -#define PA(x) (1 << (x)) - -/* - * Port B - */ -#define PBDIR_ADDR 0xfffff408 /* Port B direction reg */ -#define PBDATA_ADDR 0xfffff409 /* Port B data register */ -#define PBPUEN_ADDR 0xfffff40a /* Port B Pull-Up enable reg */ -#define PBSEL_ADDR 0xfffff40b /* Port B Select Register */ - -#define PBDIR BYTE_REF(PBDIR_ADDR) -#define PBDATA BYTE_REF(PBDATA_ADDR) -#define PBPUEN BYTE_REF(PBPUEN_ADDR) -#define PBSEL BYTE_REF(PBSEL_ADDR) - -#define PB(x) (1 << (x)) - -#define PB_CSB0 0x01 /* Use CSB0 as PB[0] */ -#define PB_CSB1 0x02 /* Use CSB1 as PB[1] */ -#define PB_CSC0_RAS0 0x04 /* Use CSC0/RAS0 as PB[2] */ -#define PB_CSC1_RAS1 0x08 /* Use CSC1/RAS1 as PB[3] */ -#define PB_CSD0_CAS0 0x10 /* Use CSD0/CAS0 as PB[4] */ -#define PB_CSD1_CAS1 0x20 /* Use CSD1/CAS1 as PB[5] */ -#define PB_TIN_TOUT 0x40 /* Use TIN/TOUT as PB[6] */ -#define PB_PWMO 0x80 /* Use PWMO as PB[7] */ - -/* - * Port C - */ -#define PCDIR_ADDR 0xfffff410 /* Port C direction reg */ -#define PCDATA_ADDR 0xfffff411 /* Port C data register */ -#define PCPDEN_ADDR 0xfffff412 /* Port C Pull-Down enb. reg */ -#define PCSEL_ADDR 0xfffff413 /* Port C Select Register */ - -#define PCDIR BYTE_REF(PCDIR_ADDR) -#define PCDATA BYTE_REF(PCDATA_ADDR) -#define PCPDEN BYTE_REF(PCPDEN_ADDR) -#define PCSEL BYTE_REF(PCSEL_ADDR) - -#define PC(x) (1 << (x)) - -#define PC_LD0 0x01 /* Use LD0 as PC[0] */ -#define PC_LD1 0x02 /* Use LD1 as PC[1] */ -#define PC_LD2 0x04 /* Use LD2 as PC[2] */ -#define PC_LD3 0x08 /* Use LD3 as PC[3] */ -#define PC_LFLM 0x10 /* Use LFLM as PC[4] */ -#define PC_LLP 0x20 /* Use LLP as PC[5] */ -#define PC_LCLK 0x40 /* Use LCLK as PC[6] */ -#define PC_LACD 0x80 /* Use LACD as PC[7] */ - -/* - * Port D - */ -#define PDDIR_ADDR 0xfffff418 /* Port D direction reg */ -#define PDDATA_ADDR 0xfffff419 /* Port D data register */ -#define PDPUEN_ADDR 0xfffff41a /* Port D Pull-Up enable reg */ -#define PDSEL_ADDR 0xfffff41b /* Port D Select Register */ -#define PDPOL_ADDR 0xfffff41c /* Port D Polarity Register */ -#define PDIRQEN_ADDR 0xfffff41d /* Port D IRQ enable register */ -#define PDKBEN_ADDR 0xfffff41e /* Port D Keyboard Enable reg */ -#define PDIQEG_ADDR 0xfffff41f /* Port D IRQ Edge Register */ - -#define PDDIR BYTE_REF(PDDIR_ADDR) -#define PDDATA BYTE_REF(PDDATA_ADDR) -#define PDPUEN BYTE_REF(PDPUEN_ADDR) -#define PDSEL BYTE_REF(PDSEL_ADDR) -#define PDPOL BYTE_REF(PDPOL_ADDR) -#define PDIRQEN BYTE_REF(PDIRQEN_ADDR) -#define PDKBEN BYTE_REF(PDKBEN_ADDR) -#define PDIQEG BYTE_REF(PDIQEG_ADDR) - -#define PD(x) (1 << (x)) - -#define PD_INT0 0x01 /* Use INT0 as PD[0] */ -#define PD_INT1 0x02 /* Use INT1 as PD[1] */ -#define PD_INT2 0x04 /* Use INT2 as PD[2] */ -#define PD_INT3 0x08 /* Use INT3 as PD[3] */ -#define PD_IRQ1 0x10 /* Use IRQ1 as PD[4] */ -#define PD_IRQ2 0x20 /* Use IRQ2 as PD[5] */ -#define PD_IRQ3 0x40 /* Use IRQ3 as PD[6] */ -#define PD_IRQ6 0x80 /* Use IRQ6 as PD[7] */ - -/* - * Port E - */ -#define PEDIR_ADDR 0xfffff420 /* Port E direction reg */ -#define PEDATA_ADDR 0xfffff421 /* Port E data register */ -#define PEPUEN_ADDR 0xfffff422 /* Port E Pull-Up enable reg */ -#define PESEL_ADDR 0xfffff423 /* Port E Select Register */ - -#define PEDIR BYTE_REF(PEDIR_ADDR) -#define PEDATA BYTE_REF(PEDATA_ADDR) -#define PEPUEN BYTE_REF(PEPUEN_ADDR) -#define PESEL BYTE_REF(PESEL_ADDR) - -#define PE(x) (1 << (x)) - -#define PE_SPMTXD 0x01 /* Use SPMTXD as PE[0] */ -#define PE_SPMRXD 0x02 /* Use SPMRXD as PE[1] */ -#define PE_SPMCLK 0x04 /* Use SPMCLK as PE[2] */ -#define PE_DWE 0x08 /* Use DWE as PE[3] */ -#define PE_RXD 0x10 /* Use RXD as PE[4] */ -#define PE_TXD 0x20 /* Use TXD as PE[5] */ -#define PE_RTS 0x40 /* Use RTS as PE[6] */ -#define PE_CTS 0x80 /* Use CTS as PE[7] */ - -/* - * Port F - */ -#define PFDIR_ADDR 0xfffff428 /* Port F direction reg */ -#define PFDATA_ADDR 0xfffff429 /* Port F data register */ -#define PFPUEN_ADDR 0xfffff42a /* Port F Pull-Up enable reg */ -#define PFSEL_ADDR 0xfffff42b /* Port F Select Register */ - -#define PFDIR BYTE_REF(PFDIR_ADDR) -#define PFDATA BYTE_REF(PFDATA_ADDR) -#define PFPUEN BYTE_REF(PFPUEN_ADDR) -#define PFSEL BYTE_REF(PFSEL_ADDR) - -#define PF(x) (1 << (x)) - -#define PF_LCONTRAST 0x01 /* Use LCONTRAST as PF[0] */ -#define PF_IRQ5 0x02 /* Use IRQ5 as PF[1] */ -#define PF_CLKO 0x04 /* Use CLKO as PF[2] */ -#define PF_A20 0x08 /* Use A20 as PF[3] */ -#define PF_A21 0x10 /* Use A21 as PF[4] */ -#define PF_A22 0x20 /* Use A22 as PF[5] */ -#define PF_A23 0x40 /* Use A23 as PF[6] */ -#define PF_CSA1 0x80 /* Use CSA1 as PF[7] */ - -/* - * Port G - */ -#define PGDIR_ADDR 0xfffff430 /* Port G direction reg */ -#define PGDATA_ADDR 0xfffff431 /* Port G data register */ -#define PGPUEN_ADDR 0xfffff432 /* Port G Pull-Up enable reg */ -#define PGSEL_ADDR 0xfffff433 /* Port G Select Register */ - -#define PGDIR BYTE_REF(PGDIR_ADDR) -#define PGDATA BYTE_REF(PGDATA_ADDR) -#define PGPUEN BYTE_REF(PGPUEN_ADDR) -#define PGSEL BYTE_REF(PGSEL_ADDR) - -#define PG(x) (1 << (x)) - -#define PG_BUSW_DTACK 0x01 /* Use BUSW/DTACK as PG[0] */ -#define PG_A0 0x02 /* Use A0 as PG[1] */ -#define PG_EMUIRQ 0x04 /* Use EMUIRQ as PG[2] */ -#define PG_HIZ_P_D 0x08 /* Use HIZ/P/D as PG[3] */ -#define PG_EMUCS 0x10 /* Use EMUCS as PG[4] */ -#define PG_EMUBRK 0x20 /* Use EMUBRK as PG[5] */ - -/* - * Port J - */ -#define PJDIR_ADDR 0xfffff438 /* Port J direction reg */ -#define PJDATA_ADDR 0xfffff439 /* Port J data register */ -#define PJPUEN_ADDR 0xfffff43A /* Port J Pull-Up enb. reg */ -#define PJSEL_ADDR 0xfffff43B /* Port J Select Register */ - -#define PJDIR BYTE_REF(PJDIR_ADDR) -#define PJDATA BYTE_REF(PJDATA_ADDR) -#define PJPUEN BYTE_REF(PJPUEN_ADDR) -#define PJSEL BYTE_REF(PJSEL_ADDR) - -#define PJ(x) (1 << (x)) - -/* - * Port K - */ -#define PKDIR_ADDR 0xfffff440 /* Port K direction reg */ -#define PKDATA_ADDR 0xfffff441 /* Port K data register */ -#define PKPUEN_ADDR 0xfffff442 /* Port K Pull-Up enb. reg */ -#define PKSEL_ADDR 0xfffff443 /* Port K Select Register */ - -#define PKDIR BYTE_REF(PKDIR_ADDR) -#define PKDATA BYTE_REF(PKDATA_ADDR) -#define PKPUEN BYTE_REF(PKPUEN_ADDR) -#define PKSEL BYTE_REF(PKSEL_ADDR) - -#define PK(x) (1 << (x)) - -#define PK_DATAREADY 0x01 /* Use ~DATA_READY as PK[0] */ -#define PK_PWM2 0x01 /* Use PWM2 as PK[0] */ -#define PK_R_W 0x02 /* Use R/W as PK[1] */ -#define PK_LDS 0x04 /* Use /LDS as PK[2] */ -#define PK_UDS 0x08 /* Use /UDS as PK[3] */ -#define PK_LD4 0x10 /* Use LD4 as PK[4] */ -#define PK_LD5 0x20 /* Use LD5 as PK[5] */ -#define PK_LD6 0x40 /* Use LD6 as PK[6] */ -#define PK_LD7 0x80 /* Use LD7 as PK[7] */ - -#define PJDIR_ADDR 0xfffff438 /* Port J direction reg */ -#define PJDATA_ADDR 0xfffff439 /* Port J data register */ -#define PJPUEN_ADDR 0xfffff43A /* Port J Pull-Up enable reg */ -#define PJSEL_ADDR 0xfffff43B /* Port J Select Register */ - -#define PJDIR BYTE_REF(PJDIR_ADDR) -#define PJDATA BYTE_REF(PJDATA_ADDR) -#define PJPUEN BYTE_REF(PJPUEN_ADDR) -#define PJSEL BYTE_REF(PJSEL_ADDR) - -#define PJ(x) (1 << (x)) - -#define PJ_MOSI 0x01 /* Use MOSI as PJ[0] */ -#define PJ_MISO 0x02 /* Use MISO as PJ[1] */ -#define PJ_SPICLK1 0x04 /* Use SPICLK1 as PJ[2] */ -#define PJ_SS 0x08 /* Use SS as PJ[3] */ -#define PJ_RXD2 0x10 /* Use RXD2 as PJ[4] */ -#define PJ_TXD2 0x20 /* Use TXD2 as PJ[5] */ -#define PJ_RTS2 0x40 /* Use RTS2 as PJ[5] */ -#define PJ_CTS2 0x80 /* Use CTS2 as PJ[5] */ - -/* - * Port M - */ -#define PMDIR_ADDR 0xfffff448 /* Port M direction reg */ -#define PMDATA_ADDR 0xfffff449 /* Port M data register */ -#define PMPUEN_ADDR 0xfffff44a /* Port M Pull-Up enable reg */ -#define PMSEL_ADDR 0xfffff44b /* Port M Select Register */ - -#define PMDIR BYTE_REF(PMDIR_ADDR) -#define PMDATA BYTE_REF(PMDATA_ADDR) -#define PMPUEN BYTE_REF(PMPUEN_ADDR) -#define PMSEL BYTE_REF(PMSEL_ADDR) - -#define PM(x) (1 << (x)) - -#define PM_SDCLK 0x01 /* Use SDCLK as PM[0] */ -#define PM_SDCE 0x02 /* Use SDCE as PM[1] */ -#define PM_DQMH 0x04 /* Use DQMH as PM[2] */ -#define PM_DQML 0x08 /* Use DQML as PM[3] */ -#define PM_SDA10 0x10 /* Use SDA10 as PM[4] */ -#define PM_DMOE 0x20 /* Use DMOE as PM[5] */ - -/********** - * - * 0xFFFFF5xx -- Pulse-Width Modulator (PWM) - * - **********/ - -/* - * PWM Control Register - */ -#define PWMC_ADDR 0xfffff500 -#define PWMC WORD_REF(PWMC_ADDR) - -#define PWMC_CLKSEL_MASK 0x0003 /* Clock Selection */ -#define PWMC_CLKSEL_SHIFT 0 -#define PWMC_REPEAT_MASK 0x000c /* Sample Repeats */ -#define PWMC_REPEAT_SHIFT 2 -#define PWMC_EN 0x0010 /* Enable PWM */ -#define PMNC_FIFOAV 0x0020 /* FIFO Available */ -#define PWMC_IRQEN 0x0040 /* Interrupt Request Enable */ -#define PWMC_IRQ 0x0080 /* Interrupt Request (FIFO empty) */ -#define PWMC_PRESCALER_MASK 0x7f00 /* Incoming Clock prescaler */ -#define PWMC_PRESCALER_SHIFT 8 -#define PWMC_CLKSRC 0x8000 /* Clock Source Select */ - -/* '328-compatible definitions */ -#define PWMC_PWMEN PWMC_EN - -/* - * PWM Sample Register - */ -#define PWMS_ADDR 0xfffff502 -#define PWMS WORD_REF(PWMS_ADDR) - -/* - * PWM Period Register - */ -#define PWMP_ADDR 0xfffff504 -#define PWMP BYTE_REF(PWMP_ADDR) - -/* - * PWM Counter Register - */ -#define PWMCNT_ADDR 0xfffff505 -#define PWMCNT BYTE_REF(PWMCNT_ADDR) - -/********** - * - * 0xFFFFF6xx -- General-Purpose Timer - * - **********/ - -/* - * Timer Control register - */ -#define TCTL_ADDR 0xfffff600 -#define TCTL WORD_REF(TCTL_ADDR) - -#define TCTL_TEN 0x0001 /* Timer Enable */ -#define TCTL_CLKSOURCE_MASK 0x000e /* Clock Source: */ -#define TCTL_CLKSOURCE_STOP 0x0000 /* Stop count (disabled) */ -#define TCTL_CLKSOURCE_SYSCLK 0x0002 /* SYSCLK to prescaler */ -#define TCTL_CLKSOURCE_SYSCLK_16 0x0004 /* SYSCLK/16 to prescaler */ -#define TCTL_CLKSOURCE_TIN 0x0006 /* TIN to prescaler */ -#define TCTL_CLKSOURCE_32KHZ 0x0008 /* 32kHz clock to prescaler */ -#define TCTL_IRQEN 0x0010 /* IRQ Enable */ -#define TCTL_OM 0x0020 /* Output Mode */ -#define TCTL_CAP_MASK 0x00c0 /* Capture Edge: */ -#define TCTL_CAP_RE 0x0040 /* Capture on rizing edge */ -#define TCTL_CAP_FE 0x0080 /* Capture on falling edge */ -#define TCTL_FRR 0x0010 /* Free-Run Mode */ - -/* '328-compatible definitions */ -#define TCTL1_ADDR TCTL_ADDR -#define TCTL1 TCTL - -/* - * Timer Prescaler Register - */ -#define TPRER_ADDR 0xfffff602 -#define TPRER WORD_REF(TPRER_ADDR) - -/* '328-compatible definitions */ -#define TPRER1_ADDR TPRER_ADDR -#define TPRER1 TPRER - -/* - * Timer Compare Register - */ -#define TCMP_ADDR 0xfffff604 -#define TCMP WORD_REF(TCMP_ADDR) - -/* '328-compatible definitions */ -#define TCMP1_ADDR TCMP_ADDR -#define TCMP1 TCMP - -/* - * Timer Capture register - */ -#define TCR_ADDR 0xfffff606 -#define TCR WORD_REF(TCR_ADDR) - -/* '328-compatible definitions */ -#define TCR1_ADDR TCR_ADDR -#define TCR1 TCR - -/* - * Timer Counter Register - */ -#define TCN_ADDR 0xfffff608 -#define TCN WORD_REF(TCN_ADDR) - -/* '328-compatible definitions */ -#define TCN1_ADDR TCN_ADDR -#define TCN1 TCN - -/* - * Timer Status Register - */ -#define TSTAT_ADDR 0xfffff60a -#define TSTAT WORD_REF(TSTAT_ADDR) - -#define TSTAT_COMP 0x0001 /* Compare Event occurred */ -#define TSTAT_CAPT 0x0001 /* Capture Event occurred */ - -/* '328-compatible definitions */ -#define TSTAT1_ADDR TSTAT_ADDR -#define TSTAT1 TSTAT - -/********** - * - * 0xFFFFF8xx -- Serial Periferial Interface Master (SPIM) - * - **********/ - -/* - * SPIM Data Register - */ -#define SPIMDATA_ADDR 0xfffff800 -#define SPIMDATA WORD_REF(SPIMDATA_ADDR) - -/* - * SPIM Control/Status Register - */ -#define SPIMCONT_ADDR 0xfffff802 -#define SPIMCONT WORD_REF(SPIMCONT_ADDR) - -#define SPIMCONT_BIT_COUNT_MASK 0x000f /* Transfer Length in Bytes */ -#define SPIMCONT_BIT_COUNT_SHIFT 0 -#define SPIMCONT_POL 0x0010 /* SPMCLK Signel Polarity */ -#define SPIMCONT_PHA 0x0020 /* Clock/Data phase relationship */ -#define SPIMCONT_IRQEN 0x0040 /* IRQ Enable */ -#define SPIMCONT_IRQ 0x0080 /* Interrupt Request */ -#define SPIMCONT_XCH 0x0100 /* Exchange */ -#define SPIMCONT_ENABLE 0x0200 /* Enable SPIM */ -#define SPIMCONT_DATA_RATE_MASK 0xe000 /* SPIM Data Rate */ -#define SPIMCONT_DATA_RATE_SHIFT 13 - -/* '328-compatible definitions */ -#define SPIMCONT_SPIMIRQ SPIMCONT_IRQ -#define SPIMCONT_SPIMEN SPIMCONT_ENABLE - -/********** - * - * 0xFFFFF9xx -- UART - * - **********/ - -/* - * UART Status/Control Register - */ - -#define USTCNT_ADDR 0xfffff900 -#define USTCNT WORD_REF(USTCNT_ADDR) - -#define USTCNT_TXAE 0x0001 /* Transmitter Available Interrupt Enable */ -#define USTCNT_TXHE 0x0002 /* Transmitter Half Empty Enable */ -#define USTCNT_TXEE 0x0004 /* Transmitter Empty Interrupt Enable */ -#define USTCNT_RXRE 0x0008 /* Receiver Ready Interrupt Enable */ -#define USTCNT_RXHE 0x0010 /* Receiver Half-Full Interrupt Enable */ -#define USTCNT_RXFE 0x0020 /* Receiver Full Interrupt Enable */ -#define USTCNT_CTSD 0x0040 /* CTS Delta Interrupt Enable */ -#define USTCNT_ODEN 0x0080 /* Old Data Interrupt Enable */ -#define USTCNT_8_7 0x0100 /* Eight or seven-bit transmission */ -#define USTCNT_STOP 0x0200 /* Stop bit transmission */ -#define USTCNT_ODD 0x0400 /* Odd Parity */ -#define USTCNT_PEN 0x0800 /* Parity Enable */ -#define USTCNT_CLKM 0x1000 /* Clock Mode Select */ -#define USTCNT_TXEN 0x2000 /* Transmitter Enable */ -#define USTCNT_RXEN 0x4000 /* Receiver Enable */ -#define USTCNT_UEN 0x8000 /* UART Enable */ - -/* '328-compatible definitions */ -#define USTCNT_TXAVAILEN USTCNT_TXAE -#define USTCNT_TXHALFEN USTCNT_TXHE -#define USTCNT_TXEMPTYEN USTCNT_TXEE -#define USTCNT_RXREADYEN USTCNT_RXRE -#define USTCNT_RXHALFEN USTCNT_RXHE -#define USTCNT_RXFULLEN USTCNT_RXFE -#define USTCNT_CTSDELTAEN USTCNT_CTSD -#define USTCNT_ODD_EVEN USTCNT_ODD -#define USTCNT_PARITYEN USTCNT_PEN -#define USTCNT_CLKMODE USTCNT_CLKM -#define USTCNT_UARTEN USTCNT_UEN - -/* - * UART Baud Control Register - */ -#define UBAUD_ADDR 0xfffff902 -#define UBAUD WORD_REF(UBAUD_ADDR) - -#define UBAUD_PRESCALER_MASK 0x003f /* Actual divisor is 65 - PRESCALER */ -#define UBAUD_PRESCALER_SHIFT 0 -#define UBAUD_DIVIDE_MASK 0x0700 /* Baud Rate freq. divizor */ -#define UBAUD_DIVIDE_SHIFT 8 -#define UBAUD_BAUD_SRC 0x0800 /* Baud Rate Source */ -#define UBAUD_UCLKDIR 0x2000 /* UCLK Direction */ - -/* - * UART Receiver Register - */ -#define URX_ADDR 0xfffff904 -#define URX WORD_REF(URX_ADDR) - -#define URX_RXDATA_ADDR 0xfffff905 -#define URX_RXDATA BYTE_REF(URX_RXDATA_ADDR) - -#define URX_RXDATA_MASK 0x00ff /* Received data */ -#define URX_RXDATA_SHIFT 0 -#define URX_PARITY_ERROR 0x0100 /* Parity Error */ -#define URX_BREAK 0x0200 /* Break Detected */ -#define URX_FRAME_ERROR 0x0400 /* Framing Error */ -#define URX_OVRUN 0x0800 /* Serial Overrun */ -#define URX_OLD_DATA 0x1000 /* Old data in FIFO */ -#define URX_DATA_READY 0x2000 /* Data Ready (FIFO not empty) */ -#define URX_FIFO_HALF 0x4000 /* FIFO is Half-Full */ -#define URX_FIFO_FULL 0x8000 /* FIFO is Full */ - -/* - * UART Transmitter Register - */ -#define UTX_ADDR 0xfffff906 -#define UTX WORD_REF(UTX_ADDR) - -#define UTX_TXDATA_ADDR 0xfffff907 -#define UTX_TXDATA BYTE_REF(UTX_TXDATA_ADDR) - -#define UTX_TXDATA_MASK 0x00ff /* Data to be transmitted */ -#define UTX_TXDATA_SHIFT 0 -#define UTX_CTS_DELTA 0x0100 /* CTS changed */ -#define UTX_CTS_STAT 0x0200 /* CTS State */ -#define UTX_BUSY 0x0400 /* FIFO is busy, sending a character */ -#define UTX_NOCTS 0x0800 /* Ignore CTS */ -#define UTX_SEND_BREAK 0x1000 /* Send a BREAK */ -#define UTX_TX_AVAIL 0x2000 /* Transmit FIFO has a slot available */ -#define UTX_FIFO_HALF 0x4000 /* Transmit FIFO is half empty */ -#define UTX_FIFO_EMPTY 0x8000 /* Transmit FIFO is empty */ - -/* '328-compatible definitions */ -#define UTX_CTS_STATUS UTX_CTS_STAT -#define UTX_IGNORE_CTS UTX_NOCTS - -/* - * UART Miscellaneous Register - */ -#define UMISC_ADDR 0xfffff908 -#define UMISC WORD_REF(UMISC_ADDR) - -#define UMISC_TX_POL 0x0004 /* Transmit Polarity */ -#define UMISC_RX_POL 0x0008 /* Receive Polarity */ -#define UMISC_IRDA_LOOP 0x0010 /* IrDA Loopback Enable */ -#define UMISC_IRDA_EN 0x0020 /* Infra-Red Enable */ -#define UMISC_RTS 0x0040 /* Set RTS status */ -#define UMISC_RTSCONT 0x0080 /* Choose RTS control */ -#define UMISC_IR_TEST 0x0400 /* IRDA Test Enable */ -#define UMISC_BAUD_RESET 0x0800 /* Reset Baud Rate Generation Counters */ -#define UMISC_LOOP 0x1000 /* Serial Loopback Enable */ -#define UMISC_FORCE_PERR 0x2000 /* Force Parity Error */ -#define UMISC_CLKSRC 0x4000 /* Clock Source */ -#define UMISC_BAUD_TEST 0x8000 /* Enable Baud Test Mode */ - -/* - * UART Non-integer Prescaler Register - */ -#define NIPR_ADDR 0xfffff90a -#define NIPR WORD_REF(NIPR_ADDR) - -#define NIPR_STEP_VALUE_MASK 0x00ff /* NI prescaler step value */ -#define NIPR_STEP_VALUE_SHIFT 0 -#define NIPR_SELECT_MASK 0x0700 /* Tap Selection */ -#define NIPR_SELECT_SHIFT 8 -#define NIPR_PRE_SEL 0x8000 /* Non-integer prescaler select */ - - -/* generalization of uart control registers to support multiple ports: */ -typedef struct { - volatile unsigned short int ustcnt; - volatile unsigned short int ubaud; - union { - volatile unsigned short int w; - struct { - volatile unsigned char status; - volatile unsigned char rxdata; - } b; - } urx; - union { - volatile unsigned short int w; - struct { - volatile unsigned char status; - volatile unsigned char txdata; - } b; - } utx; - volatile unsigned short int umisc; - volatile unsigned short int nipr; - volatile unsigned short int hmark; - volatile unsigned short int unused; -} __attribute__((packed)) m68328_uart; - - - - -/********** - * - * 0xFFFFFAxx -- LCD Controller - * - **********/ - -/* - * LCD Screen Starting Address Register - */ -#define LSSA_ADDR 0xfffffa00 -#define LSSA LONG_REF(LSSA_ADDR) - -#define LSSA_SSA_MASK 0x1ffffffe /* Bits 0 and 29-31 are reserved */ - -/* - * LCD Virtual Page Width Register - */ -#define LVPW_ADDR 0xfffffa05 -#define LVPW BYTE_REF(LVPW_ADDR) - -/* - * LCD Screen Width Register (not compatible with '328 !!!) - */ -#define LXMAX_ADDR 0xfffffa08 -#define LXMAX WORD_REF(LXMAX_ADDR) - -#define LXMAX_XM_MASK 0x02f0 /* Bits 0-3 and 10-15 are reserved */ - -/* - * LCD Screen Height Register - */ -#define LYMAX_ADDR 0xfffffa0a -#define LYMAX WORD_REF(LYMAX_ADDR) - -#define LYMAX_YM_MASK 0x01ff /* Bits 9-15 are reserved */ - -/* - * LCD Cursor X Position Register - */ -#define LCXP_ADDR 0xfffffa18 -#define LCXP WORD_REF(LCXP_ADDR) - -#define LCXP_CC_MASK 0xc000 /* Cursor Control */ -#define LCXP_CC_TRAMSPARENT 0x0000 -#define LCXP_CC_BLACK 0x4000 -#define LCXP_CC_REVERSED 0x8000 -#define LCXP_CC_WHITE 0xc000 -#define LCXP_CXP_MASK 0x02ff /* Cursor X position */ - -/* - * LCD Cursor Y Position Register - */ -#define LCYP_ADDR 0xfffffa1a -#define LCYP WORD_REF(LCYP_ADDR) - -#define LCYP_CYP_MASK 0x01ff /* Cursor Y Position */ - -/* - * LCD Cursor Width and Heigth Register - */ -#define LCWCH_ADDR 0xfffffa1c -#define LCWCH WORD_REF(LCWCH_ADDR) - -#define LCWCH_CH_MASK 0x001f /* Cursor Height */ -#define LCWCH_CH_SHIFT 0 -#define LCWCH_CW_MASK 0x1f00 /* Cursor Width */ -#define LCWCH_CW_SHIFT 8 - -/* - * LCD Blink Control Register - */ -#define LBLKC_ADDR 0xfffffa1f -#define LBLKC BYTE_REF(LBLKC_ADDR) - -#define LBLKC_BD_MASK 0x7f /* Blink Divisor */ -#define LBLKC_BD_SHIFT 0 -#define LBLKC_BKEN 0x80 /* Blink Enabled */ - -/* - * LCD Panel Interface Configuration Register - */ -#define LPICF_ADDR 0xfffffa20 -#define LPICF BYTE_REF(LPICF_ADDR) - -#define LPICF_GS_MASK 0x03 /* Gray-Scale Mode */ -#define LPICF_GS_BW 0x00 -#define LPICF_GS_GRAY_4 0x01 -#define LPICF_GS_GRAY_16 0x02 -#define LPICF_PBSIZ_MASK 0x0c /* Panel Bus Width */ -#define LPICF_PBSIZ_1 0x00 -#define LPICF_PBSIZ_2 0x04 -#define LPICF_PBSIZ_4 0x08 - -/* - * LCD Polarity Configuration Register - */ -#define LPOLCF_ADDR 0xfffffa21 -#define LPOLCF BYTE_REF(LPOLCF_ADDR) - -#define LPOLCF_PIXPOL 0x01 /* Pixel Polarity */ -#define LPOLCF_LPPOL 0x02 /* Line Pulse Polarity */ -#define LPOLCF_FLMPOL 0x04 /* Frame Marker Polarity */ -#define LPOLCF_LCKPOL 0x08 /* LCD Shift Lock Polarity */ - -/* - * LACD (LCD Alternate Crystal Direction) Rate Control Register - */ -#define LACDRC_ADDR 0xfffffa23 -#define LACDRC BYTE_REF(LACDRC_ADDR) - -#define LACDRC_ACDSLT 0x80 /* Signal Source Select */ -#define LACDRC_ACD_MASK 0x0f /* Alternate Crystal Direction Control */ -#define LACDRC_ACD_SHIFT 0 - -/* - * LCD Pixel Clock Divider Register - */ -#define LPXCD_ADDR 0xfffffa25 -#define LPXCD BYTE_REF(LPXCD_ADDR) - -#define LPXCD_PCD_MASK 0x3f /* Pixel Clock Divider */ -#define LPXCD_PCD_SHIFT 0 - -/* - * LCD Clocking Control Register - */ -#define LCKCON_ADDR 0xfffffa27 -#define LCKCON BYTE_REF(LCKCON_ADDR) - -#define LCKCON_DWS_MASK 0x0f /* Display Wait-State */ -#define LCKCON_DWS_SHIFT 0 -#define LCKCON_DWIDTH 0x40 /* Display Memory Width */ -#define LCKCON_LCDON 0x80 /* Enable LCD Controller */ - -/* '328-compatible definitions */ -#define LCKCON_DW_MASK LCKCON_DWS_MASK -#define LCKCON_DW_SHIFT LCKCON_DWS_SHIFT - -/* - * LCD Refresh Rate Adjustment Register - */ -#define LRRA_ADDR 0xfffffa29 -#define LRRA BYTE_REF(LRRA_ADDR) - -/* - * LCD Panning Offset Register - */ -#define LPOSR_ADDR 0xfffffa2d -#define LPOSR BYTE_REF(LPOSR_ADDR) - -#define LPOSR_POS_MASK 0x0f /* Pixel Offset Code */ -#define LPOSR_POS_SHIFT 0 - -/* - * LCD Frame Rate Control Modulation Register - */ -#define LFRCM_ADDR 0xfffffa31 -#define LFRCM BYTE_REF(LFRCM_ADDR) - -#define LFRCM_YMOD_MASK 0x0f /* Vertical Modulation */ -#define LFRCM_YMOD_SHIFT 0 -#define LFRCM_XMOD_MASK 0xf0 /* Horizontal Modulation */ -#define LFRCM_XMOD_SHIFT 4 - -/* - * LCD Gray Palette Mapping Register - */ -#define LGPMR_ADDR 0xfffffa33 -#define LGPMR BYTE_REF(LGPMR_ADDR) - -#define LGPMR_G1_MASK 0x0f -#define LGPMR_G1_SHIFT 0 -#define LGPMR_G2_MASK 0xf0 -#define LGPMR_G2_SHIFT 4 - -/* - * PWM Contrast Control Register - */ -#define PWMR_ADDR 0xfffffa36 -#define PWMR WORD_REF(PWMR_ADDR) - -#define PWMR_PW_MASK 0x00ff /* Pulse Width */ -#define PWMR_PW_SHIFT 0 -#define PWMR_CCPEN 0x0100 /* Contrast Control Enable */ -#define PWMR_SRC_MASK 0x0600 /* Input Clock Source */ -#define PWMR_SRC_LINE 0x0000 /* Line Pulse */ -#define PWMR_SRC_PIXEL 0x0200 /* Pixel Clock */ -#define PWMR_SRC_LCD 0x4000 /* LCD clock */ - -/********** - * - * 0xFFFFFBxx -- Real-Time Clock (RTC) - * - **********/ - -/* - * RTC Hours Minutes and Seconds Register - */ -#define RTCTIME_ADDR 0xfffffb00 -#define RTCTIME LONG_REF(RTCTIME_ADDR) - -#define RTCTIME_SECONDS_MASK 0x0000003f /* Seconds */ -#define RTCTIME_SECONDS_SHIFT 0 -#define RTCTIME_MINUTES_MASK 0x003f0000 /* Minutes */ -#define RTCTIME_MINUTES_SHIFT 16 -#define RTCTIME_HOURS_MASK 0x1f000000 /* Hours */ -#define RTCTIME_HOURS_SHIFT 24 - -/* - * RTC Alarm Register - */ -#define RTCALRM_ADDR 0xfffffb04 -#define RTCALRM LONG_REF(RTCALRM_ADDR) - -#define RTCALRM_SECONDS_MASK 0x0000003f /* Seconds */ -#define RTCALRM_SECONDS_SHIFT 0 -#define RTCALRM_MINUTES_MASK 0x003f0000 /* Minutes */ -#define RTCALRM_MINUTES_SHIFT 16 -#define RTCALRM_HOURS_MASK 0x1f000000 /* Hours */ -#define RTCALRM_HOURS_SHIFT 24 - -/* - * Watchdog Timer Register - */ -#define WATCHDOG_ADDR 0xfffffb0a -#define WATCHDOG WORD_REF(WATCHDOG_ADDR) - -#define WATCHDOG_EN 0x0001 /* Watchdog Enabled */ -#define WATCHDOG_ISEL 0x0002 /* Select the watchdog interrupt */ -#define WATCHDOG_INTF 0x0080 /* Watchdog interrupt occcured */ -#define WATCHDOG_CNT_MASK 0x0300 /* Watchdog Counter */ -#define WATCHDOG_CNT_SHIFT 8 - -/* - * RTC Control Register - */ -#define RTCCTL_ADDR 0xfffffb0c -#define RTCCTL WORD_REF(RTCCTL_ADDR) - -#define RTCCTL_XTL 0x0020 /* Crystal Selection */ -#define RTCCTL_EN 0x0080 /* RTC Enable */ - -/* '328-compatible definitions */ -#define RTCCTL_384 RTCCTL_XTL -#define RTCCTL_ENABLE RTCCTL_EN - -/* - * RTC Interrupt Status Register - */ -#define RTCISR_ADDR 0xfffffb0e -#define RTCISR WORD_REF(RTCISR_ADDR) - -#define RTCISR_SW 0x0001 /* Stopwatch timed out */ -#define RTCISR_MIN 0x0002 /* 1-minute interrupt has occurred */ -#define RTCISR_ALM 0x0004 /* Alarm interrupt has occurred */ -#define RTCISR_DAY 0x0008 /* 24-hour rollover interrupt has occurred */ -#define RTCISR_1HZ 0x0010 /* 1Hz interrupt has occurred */ -#define RTCISR_HR 0x0020 /* 1-hour interrupt has occurred */ -#define RTCISR_SAM0 0x0100 /* 4Hz / 4.6875Hz interrupt has occurred */ -#define RTCISR_SAM1 0x0200 /* 8Hz / 9.3750Hz interrupt has occurred */ -#define RTCISR_SAM2 0x0400 /* 16Hz / 18.7500Hz interrupt has occurred */ -#define RTCISR_SAM3 0x0800 /* 32Hz / 37.5000Hz interrupt has occurred */ -#define RTCISR_SAM4 0x1000 /* 64Hz / 75.0000Hz interrupt has occurred */ -#define RTCISR_SAM5 0x2000 /* 128Hz / 150.0000Hz interrupt has occurred */ -#define RTCISR_SAM6 0x4000 /* 256Hz / 300.0000Hz interrupt has occurred */ -#define RTCISR_SAM7 0x8000 /* 512Hz / 600.0000Hz interrupt has occurred */ - -/* - * RTC Interrupt Enable Register - */ -#define RTCIENR_ADDR 0xfffffb10 -#define RTCIENR WORD_REF(RTCIENR_ADDR) - -#define RTCIENR_SW 0x0001 /* Stopwatch interrupt enable */ -#define RTCIENR_MIN 0x0002 /* 1-minute interrupt enable */ -#define RTCIENR_ALM 0x0004 /* Alarm interrupt enable */ -#define RTCIENR_DAY 0x0008 /* 24-hour rollover interrupt enable */ -#define RTCIENR_1HZ 0x0010 /* 1Hz interrupt enable */ -#define RTCIENR_HR 0x0020 /* 1-hour interrupt enable */ -#define RTCIENR_SAM0 0x0100 /* 4Hz / 4.6875Hz interrupt enable */ -#define RTCIENR_SAM1 0x0200 /* 8Hz / 9.3750Hz interrupt enable */ -#define RTCIENR_SAM2 0x0400 /* 16Hz / 18.7500Hz interrupt enable */ -#define RTCIENR_SAM3 0x0800 /* 32Hz / 37.5000Hz interrupt enable */ -#define RTCIENR_SAM4 0x1000 /* 64Hz / 75.0000Hz interrupt enable */ -#define RTCIENR_SAM5 0x2000 /* 128Hz / 150.0000Hz interrupt enable */ -#define RTCIENR_SAM6 0x4000 /* 256Hz / 300.0000Hz interrupt enable */ -#define RTCIENR_SAM7 0x8000 /* 512Hz / 600.0000Hz interrupt enable */ - -/* - * Stopwatch Minutes Register - */ -#define STPWCH_ADDR 0xfffffb12 -#define STPWCH WORD_REF(STPWCH_ADDR) - -#define STPWCH_CNT_MASK 0x003f /* Stopwatch countdown value */ -#define SPTWCH_CNT_SHIFT 0 - -/* - * RTC Day Count Register - */ -#define DAYR_ADDR 0xfffffb1a -#define DAYR WORD_REF(DAYR_ADDR) - -#define DAYR_DAYS_MASK 0x1ff /* Day Setting */ -#define DAYR_DAYS_SHIFT 0 - -/* - * RTC Day Alarm Register - */ -#define DAYALARM_ADDR 0xfffffb1c -#define DAYALARM WORD_REF(DAYALARM_ADDR) - -#define DAYALARM_DAYSAL_MASK 0x01ff /* Day Setting of the Alarm */ -#define DAYALARM_DAYSAL_SHIFT 0 - -/********** - * - * 0xFFFFFCxx -- DRAM Controller - * - **********/ - -/* - * DRAM Memory Configuration Register - */ -#define DRAMMC_ADDR 0xfffffc00 -#define DRAMMC WORD_REF(DRAMMC_ADDR) - -#define DRAMMC_ROW12_MASK 0xc000 /* Row address bit for MD12 */ -#define DRAMMC_ROW12_PA10 0x0000 -#define DRAMMC_ROW12_PA21 0x4000 -#define DRAMMC_ROW12_PA23 0x8000 -#define DRAMMC_ROW0_MASK 0x3000 /* Row address bit for MD0 */ -#define DRAMMC_ROW0_PA11 0x0000 -#define DRAMMC_ROW0_PA22 0x1000 -#define DRAMMC_ROW0_PA23 0x2000 -#define DRAMMC_ROW11 0x0800 /* Row address bit for MD11 PA20/PA22 */ -#define DRAMMC_ROW10 0x0400 /* Row address bit for MD10 PA19/PA21 */ -#define DRAMMC_ROW9 0x0200 /* Row address bit for MD9 PA9/PA19 */ -#define DRAMMC_ROW8 0x0100 /* Row address bit for MD8 PA10/PA20 */ -#define DRAMMC_COL10 0x0080 /* Col address bit for MD10 PA11/PA0 */ -#define DRAMMC_COL9 0x0040 /* Col address bit for MD9 PA10/PA0 */ -#define DRAMMC_COL8 0x0020 /* Col address bit for MD8 PA9/PA0 */ -#define DRAMMC_REF_MASK 0x001f /* Reresh Cycle */ -#define DRAMMC_REF_SHIFT 0 - -/* - * DRAM Control Register - */ -#define DRAMC_ADDR 0xfffffc02 -#define DRAMC WORD_REF(DRAMC_ADDR) - -#define DRAMC_DWE 0x0001 /* DRAM Write Enable */ -#define DRAMC_RST 0x0002 /* Reset Burst Refresh Enable */ -#define DRAMC_LPR 0x0004 /* Low-Power Refresh Enable */ -#define DRAMC_SLW 0x0008 /* Slow RAM */ -#define DRAMC_LSP 0x0010 /* Light Sleep */ -#define DRAMC_MSW 0x0020 /* Slow Multiplexing */ -#define DRAMC_WS_MASK 0x00c0 /* Wait-states */ -#define DRAMC_WS_SHIFT 6 -#define DRAMC_PGSZ_MASK 0x0300 /* Page Size for fast page mode */ -#define DRAMC_PGSZ_SHIFT 8 -#define DRAMC_PGSZ_256K 0x0000 -#define DRAMC_PGSZ_512K 0x0100 -#define DRAMC_PGSZ_1024K 0x0200 -#define DRAMC_PGSZ_2048K 0x0300 -#define DRAMC_EDO 0x0400 /* EDO DRAM */ -#define DRAMC_CLK 0x0800 /* Refresh Timer Clock source select */ -#define DRAMC_BC_MASK 0x3000 /* Page Access Clock Cycle (FP mode) */ -#define DRAMC_BC_SHIFT 12 -#define DRAMC_RM 0x4000 /* Refresh Mode */ -#define DRAMC_EN 0x8000 /* DRAM Controller enable */ - - -/********** - * - * 0xFFFFFDxx -- In-Circuit Emulation (ICE) - * - **********/ - -/* - * ICE Module Address Compare Register - */ -#define ICEMACR_ADDR 0xfffffd00 -#define ICEMACR LONG_REF(ICEMACR_ADDR) - -/* - * ICE Module Address Mask Register - */ -#define ICEMAMR_ADDR 0xfffffd04 -#define ICEMAMR LONG_REF(ICEMAMR_ADDR) - -/* - * ICE Module Control Compare Register - */ -#define ICEMCCR_ADDR 0xfffffd08 -#define ICEMCCR WORD_REF(ICEMCCR_ADDR) - -#define ICEMCCR_PD 0x0001 /* Program/Data Cycle Selection */ -#define ICEMCCR_RW 0x0002 /* Read/Write Cycle Selection */ - -/* - * ICE Module Control Mask Register - */ -#define ICEMCMR_ADDR 0xfffffd0a -#define ICEMCMR WORD_REF(ICEMCMR_ADDR) - -#define ICEMCMR_PDM 0x0001 /* Program/Data Cycle Mask */ -#define ICEMCMR_RWM 0x0002 /* Read/Write Cycle Mask */ - -/* - * ICE Module Control Register - */ -#define ICEMCR_ADDR 0xfffffd0c -#define ICEMCR WORD_REF(ICEMCR_ADDR) - -#define ICEMCR_CEN 0x0001 /* Compare Enable */ -#define ICEMCR_PBEN 0x0002 /* Program Break Enable */ -#define ICEMCR_SB 0x0004 /* Single Breakpoint */ -#define ICEMCR_HMDIS 0x0008 /* HardMap disable */ -#define ICEMCR_BBIEN 0x0010 /* Bus Break Interrupt Enable */ - -/* - * ICE Module Status Register - */ -#define ICEMSR_ADDR 0xfffffd0e -#define ICEMSR WORD_REF(ICEMSR_ADDR) - -#define ICEMSR_EMUEN 0x0001 /* Emulation Enable */ -#define ICEMSR_BRKIRQ 0x0002 /* A-Line Vector Fetch Detected */ -#define ICEMSR_BBIRQ 0x0004 /* Bus Break Interrupt Detected */ -#define ICEMSR_EMIRQ 0x0008 /* EMUIRQ Falling Edge Detected */ - -#endif /* _MC68VZ328_H_ */ |