From beb116954b9b7f3bb56412b2494b562f02b864b1 Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Tue, 7 Jan 1997 02:33:00 +0000 Subject: Import of Linux/MIPS 2.1.14 --- drivers/scsi/AM53C974.h | 422 ++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 422 insertions(+) create mode 100644 drivers/scsi/AM53C974.h (limited to 'drivers/scsi/AM53C974.h') diff --git a/drivers/scsi/AM53C974.h b/drivers/scsi/AM53C974.h new file mode 100644 index 000000000..46e7ea841 --- /dev/null +++ b/drivers/scsi/AM53C974.h @@ -0,0 +1,422 @@ +/* AM53/79C974 (PCscsi) driver release 0.5 + * + * The architecture and much of the code of this device + * driver was originally developed by Drew Eckhardt for + * the NCR5380. The following copyrights apply: + * For the architecture and all parts similar to the NCR5380: + * Copyright 1993, Drew Eckhardt + * Visionary Computing + * (Unix and Linux consulting and custom programming) + * drew@colorado.edu + * +1 (303) 666-5836 + * + * The AM53C974_nobios_detect code was originally developed by + * Robin Cutshaw (robin@xfree86.org) and is used here in a + * modified form. + * + * For the other parts: + * Copyright 1994, D. Frieauff + * EMail: fri@rsx42sun0.dofn.de + * Phone: x49-7545-8-2256 , x49-7541-42305 + */ + +/* + * $Log: AM53C974.h,v $ + */ + +#ifndef AM53C974_H +#define AM53C974_H + +#include + +/*************************************************************************************** +* Default setting of the controller's SCSI id. Edit and uncomment this only if your * +* BIOS does not correctly initialize the controller's SCSI id. * +* If you don't get a warning during boot, it is correctly initialized. * +****************************************************************************************/ +/* #define AM53C974_SCSI_ID 7 */ + +/*************************************************************************************** +* Default settings for sync. negotiation enable, transfer rate and sync. offset. * +* These settings can be replaced by LILO overrides (append) with the following syntax: * +* AM53C974=host-scsi-id, target-scsi-id, max-rate, max-offset * +* Sync. negotiation is disabled by default and will be enabled for those targets which * +* are specified in the LILO override * +****************************************************************************************/ +#define DEFAULT_SYNC_NEGOTIATION_ENABLED 0 /* 0 or 1 */ +#define DEFAULT_RATE 5 /* MHz, min: 3; max: 10 */ +#define DEFAULT_SYNC_OFFSET 0 /* bytes, min: 0; max: 15; use 0 for async. mode */ + +/*************************************************************************************** +* If defined, don't allow targets to disconnect during commands. This will reduce * +* performance, but may be worthwhile if you suspect the driver of corrupting data when * +* a disconnect happens. * +***************************************************************************************/ +#define AM53C974_PROHIBIT_DISCONNECT + +/* --------------------- don't edit below here --------------------- */ + +#define AM53C974_DRIVER_REVISION_MAJOR 0 +#define AM53C974_DRIVER_REVISION_MINOR 5 +#define SEPARATOR_LINE \ +"--------------------------------------------------------------------------\n" + +/* debug control */ +/* #define AM53C974_DEBUG */ +/* #define AM53C974_DEBUG_MSG */ +/* #define AM53C974_DEBUG_KEYWAIT */ +/* #define AM53C974_DEBUG_INIT */ +/* #define AM53C974_DEBUG_QUEUE */ +/* #define AM53C974_DEBUG_INFO */ +/* #define AM53C974_DEBUG_LINKED */ +/* #define VERBOSE_AM53C974_DEBUG */ +/* #define AM53C974_DEBUG_INTR */ +/* #define AM53C974_DEB_RESEL */ +#define AM53C974_DEBUG_ABORT +/* #define AM53C974_OPTION_DEBUG_PROBE_ONLY */ + +/* special options/constants */ +#define DEF_CLK 40 /* chip clock freq. in MHz */ +#define MIN_PERIOD 4 /* for negotiation: min. number of clocks per cycle */ +#define MAX_PERIOD 13 /* for negotiation: max. number of clocks per cycle */ +#define MAX_OFFSET 15 /* for negotiation: max. offset (0=async) */ + +#define DEF_SCSI_TIMEOUT 245 /* STIMREG value, 40 Mhz */ +#define DEF_STP 8 /* STPREG value assuming 5.0 MB/sec, FASTCLK, FASTSCSI */ +#define DEF_SOF_RAD 0 /* REQ/ACK deassertion delay */ +#define DEF_SOF_RAA 0 /* REQ/ACK assertion delay */ +#define DEF_ETM 0 /* CNTLREG1, ext. timing mode */ +#define DEF_PERE 1 /* CNTLREG1, parity error reporting */ +#define DEF_CLKF 0 /* CLKFREG, 0=40 Mhz */ +#define DEF_ENF 1 /* CNTLREG2, enable features */ +#define DEF_ADIDCHK 0 /* CNTLREG3, additional ID check */ +#define DEF_FASTSCSI 1 /* CNTLREG3, fast SCSI */ +#define DEF_FASTCLK 1 /* CNTLREG3, fast clocking, 5 MB/sec at 40MHz chip clk */ +#define DEF_GLITCH 1 /* CNTLREG4, glitch eater, 0=12ns, 1=35ns, 2=25ns, 3=off */ +#define DEF_PWD 0 /* CNTLREG4, reduced power feature */ +#define DEF_RAE 0 /* CNTLREG4, RAE active negation on REQ, ACK only */ +#define DEF_RADE 1 /* 1CNTLREG4, active negation on REQ, ACK and data */ + +/*** PCI block ***/ +/* standard registers are defined in */ +#ifndef PCI_VENDOR_ID_AMD +#define PCI_VENDOR_ID_AMD 0x1022 +#define PCI_DEVICE_ID_AMD_SCSI 0x2020 +#endif +#define PCI_BASE_MASK 0xFFFFFFE0 +#define PCI_COMMAND_PERREN 0x40 +#define PCI_SCRATCH_REG_0 0x40 /* 16 bits */ +#define PCI_SCRATCH_REG_1 0x42 /* 16 bits */ +#define PCI_SCRATCH_REG_2 0x44 /* 16 bits */ +#define PCI_SCRATCH_REG_3 0x46 /* 16 bits */ +#define PCI_SCRATCH_REG_4 0x48 /* 16 bits */ +#define PCI_SCRATCH_REG_5 0x4A /* 16 bits */ +#define PCI_SCRATCH_REG_6 0x4C /* 16 bits */ +#define PCI_SCRATCH_REG_7 0x4E /* 16 bits */ + +/*** SCSI block ***/ +#define CTCLREG 0x00 /* r current transf. count, low byte */ +#define CTCMREG 0x04 /* r current transf. count, middle byte */ +#define CTCHREG 0x38 /* r current transf. count, high byte */ +#define STCLREG 0x00 /* w start transf. count, low byte */ +#define STCMREG 0x04 /* w start transf. count, middle byte */ +#define STCHREG 0x38 /* w start transf. count, high byte */ +#define FFREG 0x08 /* rw SCSI FIFO reg. */ +#define STIMREG 0x14 /* w SCSI timeout reg. */ + +#define SDIDREG 0x10 /* w SCSI destination ID reg. */ +#define SDIREG_MASK 0x07 /* mask */ + +#define STPREG 0x18 /* w synchronous transf. period reg. */ +#define STPREG_STP 0x1F /* synchr. transfer period */ + +#define CLKFREG 0x24 /* w clock factor reg. */ +#define CLKFREG_MASK 0x07 /* mask */ + +#define CMDREG 0x0C /* rw SCSI command reg. */ +#define CMDREG_DMA 0x80 /* set DMA mode (set together with opcodes below) */ +#define CMDREG_IT 0x10 /* information transfer */ +#define CMDREG_ICCS 0x11 /* initiator command complete steps */ +#define CMDREG_MA 0x12 /* message accepted */ +#define CMDREG_TPB 0x98 /* transfer pad bytes, DMA mode only */ +#define CMDREG_SATN 0x1A /* set ATN */ +#define CMDREG_RATN 0x1B /* reset ATN */ +#define CMDREG_SOAS 0x41 /* select without ATN steps */ +#define CMDREG_SAS 0x42 /* select with ATN steps (1 msg byte) */ +#define CMDREG_SASS 0x43 /* select with ATN and stop steps */ +#define CMDREG_ESR 0x44 /* enable selection/reselection */ +#define CMDREG_DSR 0x45 /* disable selection/reselection */ +#define CMDREG_SA3S 0x46 /* select with ATN 3 steps (3 msg bytes) */ +#define CMDREG_NOP 0x00 /* no operation */ +#define CMDREG_CFIFO 0x01 /* clear FIFO */ +#define CMDREG_RDEV 0x02 /* reset device */ +#define CMDREG_RBUS 0x03 /* reset SCSI bus */ + +#define STATREG 0x10 /* r SCSI status reg. */ +#define STATREG_INT 0x80 /* SCSI interrupt condition detected */ +#define STATREG_IOE 0x40 /* SCSI illegal operation error detected */ +#define STATREG_PE 0x20 /* SCSI parity error detected */ +#define STATREG_CTZ 0x10 /* CTC reg decremented to zero */ +#define STATREG_MSG 0x04 /* SCSI MSG phase (latched?) */ +#define STATREG_CD 0x02 /* SCSI C/D phase (latched?) */ +#define STATREG_IO 0x01 /* SCSI I/O phase (latched?) */ +#define STATREG_PHASE 0x07 /* SCSI phase mask */ + +#define INSTREG 0x14 /* r interrupt status reg. */ +#define INSTREG_SRST 0x80 /* SCSI reset detected */ +#define INSTREG_ICMD 0x40 /* SCSI invalid command detected */ +#define INSTREG_DIS 0x20 /* target disconnected or sel/resel timeout*/ +#define INSTREG_SR 0x10 /* device on bus has service request */ +#define INSTREG_SO 0x08 /* successful operation */ +#define INSTREG_RESEL 0x04 /* device reselected as initiator */ + +#define ISREG 0x18 /* r internal state reg. */ +#define ISREG_SOF 0x08 /* synchronous offset flag (act. low) */ +#define ISREG_IS 0x07 /* status of intermediate op. */ +#define ISREG_OK_NO_STOP 0x04 /* selection successful */ +#define ISREG_OK_STOP 0x01 /* selection successful */ + +#define CFIREG 0x1C /* r current FIFO/internal state reg. */ +#define CFIREG_IS 0xE0 /* status of intermediate op. */ +#define CFIREG_CF 0x1F /* number of bytes in SCSI FIFO */ + +#define SOFREG 0x1C /* w synchr. offset reg. */ +#define SOFREG_RAD 0xC0 /* REQ/ACK deassertion delay (sync.) */ +#define SOFREG_RAA 0x30 /* REQ/ACK assertion delay (sync.) */ +#define SOFREG_SO 0x0F /* synch. offset (sync.) */ + +#define CNTLREG1 0x20 /* rw control register one */ +#define CNTLREG1_ETM 0x80 /* set extended timing mode */ +#define CNTLREG1_DISR 0x40 /* disable interrupt on SCSI reset */ +#define CNTLREG1_PERE 0x10 /* enable parity error reporting */ +#define CNTLREG1_SID 0x07 /* host adapter SCSI ID */ + +#define CNTLREG2 0x2C /* rw control register two */ +#define CNTLREG2_ENF 0x40 /* enable features */ + +#define CNTLREG3 0x30 /* rw control register three */ +#define CNTLREG3_ADIDCHK 0x80 /* additional ID check */ +#define CNTLREG3_FASTSCSI 0x10 /* fast SCSI */ +#define CNTLREG3_FASTCLK 0x08 /* fast SCSI clocking */ + +#define CNTLREG4 0x34 /* rw control register four */ +#define CNTLREG4_GLITCH 0xC0 /* glitch eater */ +#define CNTLREG4_PWD 0x20 /* reduced power feature */ +#define CNTLREG4_RAE 0x08 /* write only, active negot. ctrl. */ +#define CNTLREG4_RADE 0x04 /* active negot. ctrl. */ +#define CNTLREG4_RES 0x10 /* reserved bit, must be 1 */ + +/*** DMA block ***/ +#define DMACMD 0x40 /* rw command */ +#define DMACMD_DIR 0x80 /* transfer direction (1=read from device) */ +#define DMACMD_INTE_D 0x40 /* DMA transfer interrupt enable */ +#define DMACMD_INTE_P 0x20 /* page transfer interrupt enable */ +#define DMACMD_MDL 0x10 /* map to memory descriptor list */ +#define DMACMD_DIAG 0x04 /* diagnostics, set to 0 */ +#define DMACMD_IDLE 0x00 /* idle cmd */ +#define DMACMD_BLAST 0x01 /* flush FIFO to memory */ +#define DMACMD_ABORT 0x02 /* terminate DMA */ +#define DMACMD_START 0x03 /* start DMA */ + +#define DMASTATUS 0x54 /* r status register */ +#define DMASTATUS_BCMPLT 0x20 /* BLAST complete */ +#define DMASTATUS_SCSIINT 0x10 /* SCSI interrupt pending */ +#define DMASTATUS_DONE 0x08 /* DMA transfer terminated */ +#define DMASTATUS_ABORT 0x04 /* DMA transfer aborted */ +#define DMASTATUS_ERROR 0x02 /* DMA transfer error */ +#define DMASTATUS_PWDN 0x02 /* power down indicator */ + +#define DMASTC 0x44 /* rw starting transfer count */ +#define DMASPA 0x48 /* rw starting physical address */ +#define DMAWBC 0x4C /* r working byte counter */ +#define DMAWAC 0x50 /* r working address counter */ +#define DMASMDLA 0x58 /* rw starting MDL address */ +#define DMAWMAC 0x5C /* r working MDL counter */ + +/*** SCSI phases ***/ +#define PHASE_MSGIN 0x07 +#define PHASE_MSGOUT 0x06 +#define PHASE_RES_1 0x05 +#define PHASE_RES_0 0x04 +#define PHASE_STATIN 0x03 +#define PHASE_CMDOUT 0x02 +#define PHASE_DATAIN 0x01 +#define PHASE_DATAOUT 0x00 + +struct AM53C974_hostdata { + volatile unsigned in_reset:1; /* flag, says bus reset pending */ + volatile unsigned aborted:1; /* flag, says aborted */ + volatile unsigned selecting:1; /* selection started, but not yet finished */ + volatile unsigned disconnecting: 1; /* disconnection started, but not yet finished */ + volatile unsigned dma_busy:1; /* dma busy when service request for info transfer received */ + volatile unsigned char msgout[10]; /* message to output in MSGOUT_PHASE */ + volatile unsigned char last_message[10]; /* last message OUT */ + volatile Scsi_Cmnd *issue_queue; /* waiting to be issued */ + volatile Scsi_Cmnd *disconnected_queue; /* waiting for reconnect */ + volatile Scsi_Cmnd *sel_cmd; /* command for selection */ + volatile Scsi_Cmnd *connected; /* currently connected command */ + volatile unsigned char busy[8]; /* index = target, bit = lun */ + unsigned char sync_per[8]; /* synchronous transfer period (in effect) */ + unsigned char sync_off[8]; /* synchronous offset (in effect) */ + unsigned char sync_neg[8]; /* sync. negotiation performed (in effect) */ + unsigned char sync_en[8]; /* sync. negotiation performed (in effect) */ + unsigned char max_rate[8]; /* max. transfer rate (setup) */ + unsigned char max_offset[8]; /* max. sync. offset (setup), only valid if corresponding sync_en is nonzero */ + }; + +extern struct proc_dir_entry proc_scsi_am53c974; + +#define AM53C974 { \ + NULL, /* pointer to next in list */ \ + NULL, /* long * usage_count */ \ + &proc_scsi_am53c974, /* struct proc_dir_entry *proc_dir */ \ + NULL, /* int (*proc_info)(char *, char **, off_t, int, int, int); */ \ + "AM53C974", /* name */ \ + AM53C974_detect, /* int (* detect)(struct SHT *) */ \ + AM53C974_release, /* int (*release)(struct Scsi_Host *) */ \ + AM53C974_info, /* const char *(* info)(struct Scsi_Host *) */ \ + AM53C974_command, /* int (* command)(Scsi_Cmnd *) */ \ + AM53C974_queue_command, /* int (* queuecommand)(Scsi_Cmnd *, \ + void (*done)(Scsi_Cmnd *)) */ \ + AM53C974_abort, /* int (* abort)(Scsi_Cmnd *) */ \ + AM53C974_reset, /* int (* reset)(Scsi_Cmnd *) */ \ + NULL, /* int (* slave_attach)(int, int) */ \ + scsicam_bios_param, /* int (* bios_param)(Disk *, int, int[]) */ \ + 12, /* can_queue */ \ + -1, /* this_id */ \ + SG_ALL, /* sg_tablesize */ \ + 1, /* cmd_per_lun */ \ + 0, /* present, i.e. how many adapters of this kind */ \ + 0, /* unchecked_isa_dma */ \ + DISABLE_CLUSTERING /* use_clustering */ \ + } + +void AM53C974_setup(char *str, int *ints); +int AM53C974_detect(Scsi_Host_Template *tpnt); +int AM53C974_release(struct Scsi_Host *shp); +int AM53C974_biosparm(Disk *disk, int dev, int *info_array); +const char *AM53C974_info(struct Scsi_Host *); +int AM53C974_command(Scsi_Cmnd *SCpnt); +int AM53C974_queue_command(Scsi_Cmnd *cmd, void (*done)(Scsi_Cmnd *)); +int AM53C974_abort(Scsi_Cmnd *cmd); +int AM53C974_reset (Scsi_Cmnd *cmd); + +#define AM53C974_local_declare() unsigned long io_port +#define AM53C974_setio(instance) io_port = instance->io_port +#define AM53C974_read_8(addr) inb(io_port + (addr)) +#define AM53C974_write_8(addr,x) outb((x), io_port + (addr)) +#define AM53C974_read_16(addr) inw(io_port + (addr)) +#define AM53C974_write_16(addr,x) outw((x), io_port + (addr)) +#define AM53C974_read_32(addr) inl(io_port + (addr)) +#define AM53C974_write_32(addr,x) outl((x), io_port + (addr)) + +#define AM53C974_poll_int() { do { statreg = AM53C974_read_8(STATREG); } \ + while (!(statreg & STATREG_INT)) ; \ + AM53C974_read_8(INSTREG) ; } /* clear int */ +#define AM53C974_cfifo() (AM53C974_read_8(CFIREG) & CFIREG_CF) + +/* These are "special" values for the tag parameter passed to AM53C974_select. */ +#define TAG_NEXT -1 /* Use next free tag */ +#define TAG_NONE -2 /* Establish I_T_L nexus instead of I_T_L_Q + * even on SCSI-II devices */ + +/************ LILO overrides *************/ +typedef struct _override_t { + int host_scsi_id; /* SCSI id of the bus controller */ + int target_scsi_id; /* SCSI id of target */ + int max_rate; /* max. transfer rate */ + int max_offset; /* max. sync. offset, 0 = asynchronous */ + } override_t; + +/************ PCI stuff *************/ +#define AM53C974_PCIREG_OPEN() outb(0xF1, 0xCF8); outb(0, 0xCFA) +#define AM53C974_PCIREG_CLOSE() outb(0, 0xCF8) +#define AM53C974_PCIREG_READ_BYTE(instance,a) ( inb((a) + (instance)->io_port) ) +#define AM53C974_PCIREG_READ_WORD(instance,a) ( inw((a) + (instance)->io_port) ) +#define AM53C974_PCIREG_READ_DWORD(instance,a) ( inl((a) + (instance)->io_port) ) +#define AM53C974_PCIREG_WRITE_BYTE(instance,x,a) ( outb((x), (a) + (instance)->io_port) ) +#define AM53C974_PCIREG_WRITE_WORD(instance,x,a) ( outw((x), (a) + (instance)->io_port) ) +#define AM53C974_PCIREG_WRITE_DWORD(instance,x,a) ( outl((x), (a) + (instance)->io_port) ) + +typedef struct _pci_config_t { + /* start of official PCI config space header */ + union { + unsigned int device_vendor; + struct { + unsigned short vendor; + unsigned short device; + } dv; + } dv_id; +#define _device_vendor dv_id.device_vendor +#define _vendor dv_id.dv.vendor +#define _device dv_id.dv.device + union { + unsigned int status_command; + struct { + unsigned short command; + unsigned short status; + } sc; + } stat_cmd; +#define _status_command stat_cmd.status_command +#define _command stat_cmd.sc.command +#define _status stat_cmd.sc.status + union { + unsigned int class_revision; + struct { + unsigned char rev_id; + unsigned char prog_if; + unsigned char sub_class; + unsigned char base_class; + } cr; + } class_rev; +#define _class_revision class_rev.class_revision +#define _rev_id class_rev.cr.rev_id +#define _prog_if class_rev.cr.prog_if +#define _sub_class class_rev.cr.sub_class +#define _base_class class_rev.cr.base_class + union { + unsigned int bist_header_latency_cache; + struct { + unsigned char cache_line_size; + unsigned char latency_timer; + unsigned char header_type; + unsigned char bist; + } bhlc; + } bhlc; +#define _bist_header_latency_cache bhlc.bist_header_latency_cache +#define _cache_line_size bhlc.bhlc.cache_line_size +#define _latency_timer bhlc.bhlc.latency_timer +#define _header_type bhlc.bhlc.header_type +#define _bist bhlc.bhlc.bist + unsigned int _base0; + unsigned int _base1; + unsigned int _base2; + unsigned int _base3; + unsigned int _base4; + unsigned int _base5; + unsigned int rsvd1; + unsigned int rsvd2; + unsigned int _baserom; + unsigned int rsvd3; + unsigned int rsvd4; + union { + unsigned int max_min_ipin_iline; + struct { + unsigned char int_line; + unsigned char int_pin; + unsigned char min_gnt; + unsigned char max_lat; + } mmii; + } mmii; +#define _max_min_ipin_iline mmii.max_min_ipin_iline +#define _int_line mmii.mmii.int_line +#define _int_pin mmii.mmii.int_pin +#define _min_gnt mmii.mmii.min_gnt +#define _max_lat mmii.mmii.max_lat + /* end of official PCI config space header */ + unsigned short _ioaddr; /* config type 1 - private I/O addr */ + unsigned int _pcibus; /* config type 2 - private bus id */ + unsigned int _cardnum; /* config type 2 - private card number */ +} pci_config_t; + +#endif /* AM53C974_H */ -- cgit v1.2.3