From 681da38cd51623972fce0f22d20000d004f423b7 Mon Sep 17 00:00:00 2001 From: Kanoj Sarcar Date: Sun, 26 Nov 2000 22:30:43 +0000 Subject: include/asm-mips64/ioc3.h replaced by include/asm-mips64/sn/ioc3.h. --- include/asm-mips64/ioc3.h | 662 ---------------------------------------------- 1 file changed, 662 deletions(-) delete mode 100644 include/asm-mips64/ioc3.h (limited to 'include/asm-mips64') diff --git a/include/asm-mips64/ioc3.h b/include/asm-mips64/ioc3.h deleted file mode 100644 index 57a2abbf2..000000000 --- a/include/asm-mips64/ioc3.h +++ /dev/null @@ -1,662 +0,0 @@ -/* $Id: ioc3.h,v 1.1 2000/01/13 00:17:02 ralf Exp $ - * - * Copyright (C) 1999 Ralf Baechle - * This file is part of the Linux driver for the SGI IOC3. - */ -#ifndef IOC3_H -#define IOC3_H - -/* SUPERIO uart register map */ -typedef volatile struct ioc3_uartregs { - union { - volatile u8 rbr; /* read only, DLAB == 0 */ - volatile u8 thr; /* write only, DLAB == 0 */ - volatile u8 dll; /* DLAB == 1 */ - } u1; - union { - volatile u8 ier; /* DLAB == 0 */ - volatile u8 dlm; /* DLAB == 1 */ - } u2; - union { - volatile u8 iir; /* read only */ - volatile u8 fcr; /* write only */ - } u3; - volatile u8 iu_lcr; - volatile u8 iu_mcr; - volatile u8 iu_lsr; - volatile u8 iu_msr; - volatile u8 iu_scr; -} ioc3_uregs_t; - -#define iu_rbr u1.rbr -#define iu_thr u1.thr -#define iu_dll u1.dll -#define iu_ier u2.ier -#define iu_dlm u2.dlm -#define iu_iir u3.iir -#define iu_fcr u3.fcr - -struct ioc3_sioregs { - volatile u8 fill[0x141]; /* starts at 0x141 */ - - volatile u8 uartc; - volatile u8 kbdcg; - - volatile u8 fill0[0x150 - 0x142 - 1]; - - volatile u8 pp_data; - volatile u8 pp_dsr; - volatile u8 pp_dcr; - - volatile u8 fill1[0x158 - 0x152 - 1]; - - volatile u8 pp_fifa; - volatile u8 pp_cfgb; - volatile u8 pp_ecr; - - volatile u8 fill2[0x168 - 0x15a - 1]; - - volatile u8 rtcad; - volatile u8 rtcdat; - - volatile u8 fill3[0x170 - 0x169 - 1]; - - struct ioc3_uartregs uartb; /* 0x20170 */ - struct ioc3_uartregs uarta; /* 0x20178 */ -}; - -/* Register layout of IOC3 in configuration space. */ -struct ioc3 { - volatile u32 pad0[7]; /* 0x00000 */ - volatile u32 sio_ir; /* 0x0001c */ - volatile u32 sio_ies; /* 0x00020 */ - volatile u32 sio_iec; /* 0x00024 */ - volatile u32 sio_cr; /* 0x00028 */ - volatile u32 int_out; /* 0x0002c */ - volatile u32 mcr; /* 0x00030 */ - - /* General Purpose I/O registers */ - volatile u32 gpcr_s; /* 0x00034 */ - volatile u32 gpcr_c; /* 0x00038 */ - volatile u32 gpdr; /* 0x0003c */ - volatile u32 gppr_0; /* 0x00040 */ - volatile u32 gppr_1; /* 0x00044 */ - volatile u32 gppr_2; /* 0x00048 */ - volatile u32 gppr_3; /* 0x0004c */ - volatile u32 gppr_4; /* 0x00050 */ - volatile u32 gppr_5; /* 0x00054 */ - volatile u32 gppr_6; /* 0x00058 */ - volatile u32 gppr_7; /* 0x0005c */ - volatile u32 gppr_8; /* 0x00060 */ - volatile u32 gppr_9; /* 0x00064 */ - volatile u32 gppr_10; /* 0x00068 */ - volatile u32 gppr_11; /* 0x0006c */ - volatile u32 gppr_12; /* 0x00070 */ - volatile u32 gppr_13; /* 0x00074 */ - volatile u32 gppr_14; /* 0x00078 */ - volatile u32 gppr_15; /* 0x0007c */ - - /* Parallel Port Registers */ - volatile u32 ppbr_h_a; /* 0x00080 */ - volatile u32 ppbr_l_a; /* 0x00084 */ - volatile u32 ppcr_a; /* 0x00088 */ - volatile u32 ppcr; /* 0x0008c */ - volatile u32 ppbr_h_b; /* 0x00090 */ - volatile u32 ppbr_l_b; /* 0x00094 */ - volatile u32 ppcr_b; /* 0x00098 */ - - /* Keyboard and Mouse Registers */ - volatile u32 km_csr; /* 0x0009c */ - volatile u32 k_rd; /* 0x000a0 */ - volatile u32 m_rd; /* 0x000a4 */ - volatile u32 k_wd; /* 0x000a8 */ - volatile u32 m_wd; /* 0x000ac */ - - /* Serial Port Registers */ - volatile u32 sbbr_h; /* 0x000b0 */ - volatile u32 sbbr_l; /* 0x000b4 */ - volatile u32 sscr_a; /* 0x000b8 */ - volatile u32 stpir_a; /* 0x000bc */ - volatile u32 stcir_a; /* 0x000c0 */ - volatile u32 srpir_a; /* 0x000c4 */ - volatile u32 srcir_a; /* 0x000c8 */ - volatile u32 srtr_a; /* 0x000cc */ - volatile u32 shadow_a; /* 0x000d0 */ - volatile u32 sscr_b; /* 0x000d4 */ - volatile u32 stpir_b; /* 0x000d8 */ - volatile u32 stcir_b; /* 0x000dc */ - volatile u32 srpir_b; /* 0x000e0 */ - volatile u32 srcir_b; /* 0x000e4 */ - volatile u32 srtr_b; /* 0x000e8 */ - volatile u32 shadow_b; /* 0x000ec */ - - /* Ethernet Registers */ - volatile u32 emcr; /* 0x000f0 */ - volatile u32 eisr; /* 0x000f4 */ - volatile u32 eier; /* 0x000f8 */ - volatile u32 ercsr; /* 0x000fc */ - volatile u32 erbr_h; /* 0x00100 */ - volatile u32 erbr_l; /* 0x00104 */ - volatile u32 erbar; /* 0x00108 */ - volatile u32 ercir; /* 0x0010c */ - volatile u32 erpir; /* 0x00110 */ - volatile u32 ertr; /* 0x00114 */ - volatile u32 etcsr; /* 0x00118 */ - volatile u32 ersr; /* 0x0011c */ - volatile u32 etcdc; /* 0x00120 */ - volatile u32 ebir; /* 0x00124 */ - volatile u32 etbr_h; /* 0x00128 */ - volatile u32 etbr_l; /* 0x0012c */ - volatile u32 etcir; /* 0x00130 */ - volatile u32 etpir; /* 0x00134 */ - volatile u32 emar_h; /* 0x00138 */ - volatile u32 emar_l; /* 0x0013c */ - volatile u32 ehar_h; /* 0x00140 */ - volatile u32 ehar_l; /* 0x00144 */ - volatile u32 micr; /* 0x00148 */ - volatile u32 midr_r; /* 0x0014c */ - volatile u32 midr_w; /* 0x00150 */ - volatile u32 pad1[(0x20000 - 0x00154) / 4]; - - /* SuperIO Registers XXX */ - struct ioc3_sioregs sregs; /* 0x20000 */ - volatile u32 pad2[(0x40000 - 0x20180) / 4]; - - /* SSRAM Diagnostic Access */ - volatile u32 ssram[(0x80000 - 0x40000) / 4]; - - /* Bytebus device offsets - 0x80000 - Access to the generic devices selected with DEV0 - 0x9FFFF bytebus DEV_SEL_0 - 0xA0000 - Access to the generic devices selected with DEV1 - 0xBFFFF bytebus DEV_SEL_1 - 0xC0000 - Access to the generic devices selected with DEV2 - 0xDFFFF bytebus DEV_SEL_2 - 0xE0000 - Access to the generic devices selected with DEV3 - 0xFFFFF bytebus DEV_SEL_3 */ -}; - -/* - * Ethernet RX Buffer - */ -struct ioc3_erxbuf { - u32 w0; /* first word (valid,bcnt,cksum) */ - u32 err; /* second word various errors */ - /* next comes n bytes of padding */ - /* then the received ethernet frame itself */ -}; - -#define ERXBUF_IPCKSUM_MASK 0x0000ffff -#define ERXBUF_BYTECNT_MASK 0x07ff0000 -#define ERXBUF_BYTECNT_SHIFT 16 -#define ERXBUF_V 0x80000000 - -#define ERXBUF_CRCERR 0x00000001 /* aka RSV15 */ -#define ERXBUF_FRAMERR 0x00000002 /* aka RSV14 */ -#define ERXBUF_CODERR 0x00000004 /* aka RSV13 */ -#define ERXBUF_INVPREAMB 0x00000008 /* aka RSV18 */ -#define ERXBUF_LOLEN 0x00007000 /* aka RSV2_0 */ -#define ERXBUF_HILEN 0x03ff0000 /* aka RSV12_3 */ -#define ERXBUF_MULTICAST 0x04000000 /* aka RSV16 */ -#define ERXBUF_BROADCAST 0x08000000 /* aka RSV17 */ -#define ERXBUF_LONGEVENT 0x10000000 /* aka RSV19 */ -#define ERXBUF_BADPKT 0x20000000 /* aka RSV20 */ -#define ERXBUF_GOODPKT 0x40000000 /* aka RSV21 */ -#define ERXBUF_CARRIER 0x80000000 /* aka RSV22 */ - -/* - * Ethernet TX Descriptor - */ -#define ETXD_DATALEN 104 -struct ioc3_etxd { - u32 cmd; /* command field */ - u32 bufcnt; /* buffer counts field */ - u64 p1; /* buffer pointer 1 */ - u64 p2; /* buffer pointer 2 */ - u8 data[ETXD_DATALEN]; /* opt. tx data */ -}; - -#define ETXD_BYTECNT_MASK 0x000007ff /* total byte count */ -#define ETXD_INTWHENDONE 0x00001000 /* intr when done */ -#define ETXD_D0V 0x00010000 /* data 0 valid */ -#define ETXD_B1V 0x00020000 /* buf 1 valid */ -#define ETXD_B2V 0x00040000 /* buf 2 valid */ -#define ETXD_DOCHECKSUM 0x00080000 /* insert ip cksum */ -#define ETXD_CHKOFF_MASK 0x07f00000 /* cksum byte offset */ -#define ETXD_CHKOFF_SHIFT 20 - -#define ETXD_D0CNT_MASK 0x0000007f -#define ETXD_B1CNT_MASK 0x0007ff00 -#define ETXD_B1CNT_SHIFT 8 -#define ETXD_B2CNT_MASK 0x7ff00000 -#define ETXD_B2CNT_SHIFT 20 - -/* - * Bytebus device space - */ -#define IOC3_BYTEBUS_DEV0 0x80000L -#define IOC3_BYTEBUS_DEV1 0xa0000L -#define IOC3_BYTEBUS_DEV2 0xc0000L -#define IOC3_BYTEBUS_DEV3 0xe0000L - -/* ------------------------------------------------------------------------- */ - -/* Superio Registers (PIO Access) */ -#define IOC3_SIO_BASE 0x20000 -#define IOC3_SIO_UARTC (IOC3_SIO_BASE+0x141) /* UART Config */ -#define IOC3_SIO_KBDCG (IOC3_SIO_BASE+0x142) /* KBD Config */ -#define IOC3_SIO_PP_BASE (IOC3_SIO_BASE+PP_BASE) /* Parallel Port */ -#define IOC3_SIO_RTC_BASE (IOC3_SIO_BASE+0x168) /* Real Time Clock */ -#define IOC3_SIO_UB_BASE (IOC3_SIO_BASE+UARTB_BASE) /* UART B */ -#define IOC3_SIO_UA_BASE (IOC3_SIO_BASE+UARTA_BASE) /* UART A */ - -/* SSRAM Diagnostic Access */ -#define IOC3_SSRAM IOC3_RAM_OFF /* base of SSRAM diagnostic access */ -#define IOC3_SSRAM_LEN 0x40000 /* 256kb (address space size, may not be fully populated) */ -#define IOC3_SSRAM_DM 0x0000ffff /* data mask */ -#define IOC3_SSRAM_PM 0x00010000 /* parity mask */ - -/* bitmasks for PCI_SCR */ -#define PCI_SCR_PAR_RESP_EN 0x00000040 /* enb PCI parity checking */ -#define PCI_SCR_SERR_EN 0x00000100 /* enable the SERR# driver */ -#define PCI_SCR_DROP_MODE_EN 0x00008000 /* drop pios on parity err */ -#define PCI_SCR_RX_SERR (0x1 << 16) -#define PCI_SCR_DROP_MODE (0x1 << 17) -#define PCI_SCR_SIG_PAR_ERR (0x1 << 24) -#define PCI_SCR_SIG_TAR_ABRT (0x1 << 27) -#define PCI_SCR_RX_TAR_ABRT (0x1 << 28) -#define PCI_SCR_SIG_MST_ABRT (0x1 << 29) -#define PCI_SCR_SIG_SERR (0x1 << 30) -#define PCI_SCR_PAR_ERR (0x1 << 31) - -/* bitmasks for IOC3_KM_CSR */ -#define KM_CSR_K_WRT_PEND 0x00000001 /* kbd port xmitting or resetting */ -#define KM_CSR_M_WRT_PEND 0x00000002 /* mouse port xmitting or resetting */ -#define KM_CSR_K_LCB 0x00000004 /* Line Cntrl Bit for last KBD write */ -#define KM_CSR_M_LCB 0x00000008 /* same for mouse */ -#define KM_CSR_K_DATA 0x00000010 /* state of kbd data line */ -#define KM_CSR_K_CLK 0x00000020 /* state of kbd clock line */ -#define KM_CSR_K_PULL_DATA 0x00000040 /* pull kbd data line low */ -#define KM_CSR_K_PULL_CLK 0x00000080 /* pull kbd clock line low */ -#define KM_CSR_M_DATA 0x00000100 /* state of ms data line */ -#define KM_CSR_M_CLK 0x00000200 /* state of ms clock line */ -#define KM_CSR_M_PULL_DATA 0x00000400 /* pull ms data line low */ -#define KM_CSR_M_PULL_CLK 0x00000800 /* pull ms clock line low */ -#define KM_CSR_EMM_MODE 0x00001000 /* emulation mode */ -#define KM_CSR_SIM_MODE 0x00002000 /* clock X8 */ -#define KM_CSR_K_SM_IDLE 0x00004000 /* Keyboard is idle */ -#define KM_CSR_M_SM_IDLE 0x00008000 /* Mouse is idle */ -#define KM_CSR_K_TO 0x00010000 /* Keyboard trying to send/receive */ -#define KM_CSR_M_TO 0x00020000 /* Mouse trying to send/receive */ -#define KM_CSR_K_TO_EN 0x00040000 /* KM_CSR_K_TO + KM_CSR_K_TO_EN = cause - SIO_IR to assert */ -#define KM_CSR_M_TO_EN 0x00080000 /* KM_CSR_M_TO + KM_CSR_M_TO_EN = cause - SIO_IR to assert */ -#define KM_CSR_K_CLAMP_ONE 0x00100000 /* Pull K_CLK low after rec. one char */ -#define KM_CSR_M_CLAMP_ONE 0x00200000 /* Pull M_CLK low after rec. one char */ -#define KM_CSR_K_CLAMP_THREE 0x00400000 /* Pull K_CLK low after rec. three chars */ -#define KM_CSR_M_CLAMP_THREE 0x00800000 /* Pull M_CLK low after rec. three char */ - -/* bitmasks for IOC3_K_RD and IOC3_M_RD */ -#define KM_RD_DATA_2 0x000000ff /* 3rd char recvd since last read */ -#define KM_RD_DATA_2_SHIFT 0 -#define KM_RD_DATA_1 0x0000ff00 /* 2nd char recvd since last read */ -#define KM_RD_DATA_1_SHIFT 8 -#define KM_RD_DATA_0 0x00ff0000 /* 1st char recvd since last read */ -#define KM_RD_DATA_0_SHIFT 16 -#define KM_RD_FRAME_ERR_2 0x01000000 /* framing or parity error in byte 2 */ -#define KM_RD_FRAME_ERR_1 0x02000000 /* same for byte 1 */ -#define KM_RD_FRAME_ERR_0 0x04000000 /* same for byte 0 */ - -#define KM_RD_KBD_MSE 0x08000000 /* 0 if from kbd, 1 if from mouse */ -#define KM_RD_OFLO 0x10000000 /* 4th char recvd before this read */ -#define KM_RD_VALID_2 0x20000000 /* DATA_2 valid */ -#define KM_RD_VALID_1 0x40000000 /* DATA_1 valid */ -#define KM_RD_VALID_0 0x80000000 /* DATA_0 valid */ -#define KM_RD_VALID_ALL (KM_RD_VALID_0|KM_RD_VALID_1|KM_RD_VALID_2) - -/* bitmasks for IOC3_K_WD & IOC3_M_WD */ -#define KM_WD_WRT_DATA 0x000000ff /* write to keyboard/mouse port */ -#define KM_WD_WRT_DATA_SHIFT 0 - -/* bitmasks for serial RX status byte */ -#define RXSB_OVERRUN 0x01 /* char(s) lost */ -#define RXSB_PAR_ERR 0x02 /* parity error */ -#define RXSB_FRAME_ERR 0x04 /* framing error */ -#define RXSB_BREAK 0x08 /* break character */ -#define RXSB_CTS 0x10 /* state of CTS */ -#define RXSB_DCD 0x20 /* state of DCD */ -#define RXSB_MODEM_VALID 0x40 /* DCD, CTS and OVERRUN are valid */ -#define RXSB_DATA_VALID 0x80 /* data byte, FRAME_ERR PAR_ERR & BREAK valid */ - -/* bitmasks for serial TX control byte */ -#define TXCB_INT_WHEN_DONE 0x20 /* interrupt after this byte is sent */ -#define TXCB_INVALID 0x00 /* byte is invalid */ -#define TXCB_VALID 0x40 /* byte is valid */ -#define TXCB_MCR 0x80 /* data<7:0> to modem control register */ -#define TXCB_DELAY 0xc0 /* delay data<7:0> mSec */ - -/* bitmasks for IOC3_SBBR_L */ -#define SBBR_L_SIZE 0x00000001 /* 0 == 1KB rings, 1 == 4KB rings */ -#define SBBR_L_BASE 0xfffff000 /* lower serial ring base addr */ - -/* bitmasks for IOC3_SSCR_ */ -#define SSCR_RX_THRESHOLD 0x000001ff /* hiwater mark */ -#define SSCR_TX_TIMER_BUSY 0x00010000 /* TX timer in progress */ -#define SSCR_HFC_EN 0x00020000 /* hardware flow control enabled */ -#define SSCR_RX_RING_DCD 0x00040000 /* post RX record on delta-DCD */ -#define SSCR_RX_RING_CTS 0x00080000 /* post RX record on delta-CTS */ -#define SSCR_HIGH_SPD 0x00100000 /* 4X speed */ -#define SSCR_DIAG 0x00200000 /* bypass clock divider for sim */ -#define SSCR_RX_DRAIN 0x08000000 /* drain RX buffer to memory */ -#define SSCR_DMA_EN 0x10000000 /* enable ring buffer DMA */ -#define SSCR_DMA_PAUSE 0x20000000 /* pause DMA */ -#define SSCR_PAUSE_STATE 0x40000000 /* sets when PAUSE takes effect */ -#define SSCR_RESET 0x80000000 /* reset DMA channels */ - -/* all producer/comsumer pointers are the same bitfield */ -#define PROD_CONS_PTR_4K 0x00000ff8 /* for 4K buffers */ -#define PROD_CONS_PTR_1K 0x000003f8 /* for 1K buffers */ -#define PROD_CONS_PTR_OFF 3 - -/* bitmasks for IOC3_SRCIR_ */ -#define SRCIR_ARM 0x80000000 /* arm RX timer */ - -/* bitmasks for IOC3_SRPIR_ */ -#define SRPIR_BYTE_CNT 0x07000000 /* bytes in packer */ -#define SRPIR_BYTE_CNT_SHIFT 24 - -/* bitmasks for IOC3_STCIR_ */ -#define STCIR_BYTE_CNT 0x0f000000 /* bytes in unpacker */ -#define STCIR_BYTE_CNT_SHIFT 24 - -/* bitmasks for IOC3_SHADOW_ */ -#define SHADOW_DR 0x00000001 /* data ready */ -#define SHADOW_OE 0x00000002 /* overrun error */ -#define SHADOW_PE 0x00000004 /* parity error */ -#define SHADOW_FE 0x00000008 /* framing error */ -#define SHADOW_BI 0x00000010 /* break interrupt */ -#define SHADOW_THRE 0x00000020 /* transmit holding register empty */ -#define SHADOW_TEMT 0x00000040 /* transmit shift register empty */ -#define SHADOW_RFCE 0x00000080 /* char in RX fifo has an error */ -#define SHADOW_DCTS 0x00010000 /* delta clear to send */ -#define SHADOW_DDCD 0x00080000 /* delta data carrier detect */ -#define SHADOW_CTS 0x00100000 /* clear to send */ -#define SHADOW_DCD 0x00800000 /* data carrier detect */ -#define SHADOW_DTR 0x01000000 /* data terminal ready */ -#define SHADOW_RTS 0x02000000 /* request to send */ -#define SHADOW_OUT1 0x04000000 /* 16550 OUT1 bit */ -#define SHADOW_OUT2 0x08000000 /* 16550 OUT2 bit */ -#define SHADOW_LOOP 0x10000000 /* loopback enabled */ - -/* bitmasks for IOC3_SRTR_ */ -#define SRTR_CNT 0x00000fff /* reload value for RX timer */ -#define SRTR_CNT_VAL 0x0fff0000 /* current value of RX timer */ -#define SRTR_CNT_VAL_SHIFT 16 -#define SRTR_HZ 16000 /* SRTR clock frequency */ - -/* bitmasks for IOC3_SIO_IR, IOC3_SIO_IEC and IOC3_SIO_IES */ -#define SIO_IR_SA_TX_MT 0x00000001 /* Serial port A TX empty */ -#define SIO_IR_SA_RX_FULL 0x00000002 /* port A RX buf full */ -#define SIO_IR_SA_RX_HIGH 0x00000004 /* port A RX hiwat */ -#define SIO_IR_SA_RX_TIMER 0x00000008 /* port A RX timeout */ -#define SIO_IR_SA_DELTA_DCD 0x00000010 /* port A delta DCD */ -#define SIO_IR_SA_DELTA_CTS 0x00000020 /* port A delta CTS */ -#define SIO_IR_SA_INT 0x00000040 /* port A pass-thru intr */ -#define SIO_IR_SA_TX_EXPLICIT 0x00000080 /* port A explicit TX thru */ -#define SIO_IR_SA_MEMERR 0x00000100 /* port A PCI error */ -#define SIO_IR_SB_TX_MT 0x00000200 /* */ -#define SIO_IR_SB_RX_FULL 0x00000400 /* */ -#define SIO_IR_SB_RX_HIGH 0x00000800 /* */ -#define SIO_IR_SB_RX_TIMER 0x00001000 /* */ -#define SIO_IR_SB_DELTA_DCD 0x00002000 /* */ -#define SIO_IR_SB_DELTA_CTS 0x00004000 /* */ -#define SIO_IR_SB_INT 0x00008000 /* */ -#define SIO_IR_SB_TX_EXPLICIT 0x00010000 /* */ -#define SIO_IR_SB_MEMERR 0x00020000 /* */ -#define SIO_IR_PP_INT 0x00040000 /* P port pass-thru intr */ -#define SIO_IR_PP_INTA 0x00080000 /* PP context A thru */ -#define SIO_IR_PP_INTB 0x00100000 /* PP context B thru */ -#define SIO_IR_PP_MEMERR 0x00200000 /* PP PCI error */ -#define SIO_IR_KBD_INT 0x00400000 /* kbd/mouse intr */ -#define SIO_IR_RT_INT 0x08000000 /* RT output pulse */ -#define SIO_IR_GEN_INT1 0x10000000 /* RT input pulse */ -#define SIO_IR_GEN_INT_SHIFT 28 - -/* per device interrupt masks */ -#define SIO_IR_SA (SIO_IR_SA_TX_MT | SIO_IR_SA_RX_FULL | \ - SIO_IR_SA_RX_HIGH | SIO_IR_SA_RX_TIMER | \ - SIO_IR_SA_DELTA_DCD | SIO_IR_SA_DELTA_CTS | \ - SIO_IR_SA_INT | SIO_IR_SA_TX_EXPLICIT | \ - SIO_IR_SA_MEMERR) -#define SIO_IR_SB (SIO_IR_SB_TX_MT | SIO_IR_SB_RX_FULL | \ - SIO_IR_SB_RX_HIGH | SIO_IR_SB_RX_TIMER | \ - SIO_IR_SB_DELTA_DCD | SIO_IR_SB_DELTA_CTS | \ - SIO_IR_SB_INT | SIO_IR_SB_TX_EXPLICIT | \ - SIO_IR_SB_MEMERR) -#define SIO_IR_PP (SIO_IR_PP_INT | SIO_IR_PP_INTA | \ - SIO_IR_PP_INTB | SIO_IR_PP_MEMERR) -#define SIO_IR_RT (SIO_IR_RT_INT | SIO_IR_GEN_INT1) - -/* macro to load pending interrupts */ -#define IOC3_PENDING_INTRS(mem) (PCI_INW(&((mem)->sio_ir)) & \ - PCI_INW(&((mem)->sio_ies_ro))) - -/* bitmasks for SIO_CR */ -#define SIO_CR_SIO_RESET 0x00000001 /* reset the SIO */ -#define SIO_CR_SER_A_BASE 0x000000fe /* DMA poll addr port A */ -#define SIO_CR_SER_A_BASE_SHIFT 1 -#define SIO_CR_SER_B_BASE 0x00007f00 /* DMA poll addr port B */ -#define SIO_CR_SER_B_BASE_SHIFT 8 -#define SIO_SR_CMD_PULSE 0x00078000 /* byte bus strobe length */ -#define SIO_CR_CMD_PULSE_SHIFT 15 -#define SIO_CR_ARB_DIAG 0x00380000 /* cur !enet PCI requet (ro) */ -#define SIO_CR_ARB_DIAG_TXA 0x00000000 -#define SIO_CR_ARB_DIAG_RXA 0x00080000 -#define SIO_CR_ARB_DIAG_TXB 0x00100000 -#define SIO_CR_ARB_DIAG_RXB 0x00180000 -#define SIO_CR_ARB_DIAG_PP 0x00200000 -#define SIO_CR_ARB_DIAG_IDLE 0x00400000 /* 0 -> active request (ro) */ - -/* bitmasks for INT_OUT */ -#define INT_OUT_COUNT 0x0000ffff /* pulse interval timer */ -#define INT_OUT_MODE 0x00070000 /* mode mask */ -#define INT_OUT_MODE_0 0x00000000 /* set output to 0 */ -#define INT_OUT_MODE_1 0x00040000 /* set output to 1 */ -#define INT_OUT_MODE_1PULSE 0x00050000 /* send 1 pulse */ -#define INT_OUT_MODE_PULSES 0x00060000 /* send 1 pulse every interval */ -#define INT_OUT_MODE_SQW 0x00070000 /* toggle output every interval */ -#define INT_OUT_DIAG 0x40000000 /* diag mode */ -#define INT_OUT_INT_OUT 0x80000000 /* current state of INT_OUT */ - -/* time constants for INT_OUT */ -#define INT_OUT_NS_PER_TICK (30 * 260) /* 30 ns PCI clock, divisor=260 */ -#define INT_OUT_TICKS_PER_PULSE 3 /* outgoing pulse lasts 3 ticks */ -#define INT_OUT_US_TO_COUNT(x) /* convert uS to a count value */ \ - (((x) * 10 + INT_OUT_NS_PER_TICK / 200) * \ - 100 / INT_OUT_NS_PER_TICK - 1) -#define INT_OUT_COUNT_TO_US(x) /* convert count value to uS */ \ - (((x) + 1) * INT_OUT_NS_PER_TICK / 1000) -#define INT_OUT_MIN_TICKS 3 /* min period is width of pulse in "ticks" */ -#define INT_OUT_MAX_TICKS INT_OUT_COUNT /* largest possible count */ - -/* bitmasks for GPCR */ -#define GPCR_DIR 0x000000ff /* tristate pin input or output */ -#define GPCR_DIR_PIN(x) (1<<(x)) /* access one of the DIR bits */ -#define GPCR_EDGE 0x000f0000 /* extint edge or level sensitive */ -#define GPCR_EDGE_PIN(x) (1<<((x)+15)) /* access one of the EDGE bits */ - -/* values for GPCR */ -#define GPCR_INT_OUT_EN 0x00100000 /* enable INT_OUT to pin 0 */ -#define GPCR_MLAN_EN 0x00200000 /* enable MCR to pin 8 */ -#define GPCR_DIR_SERA_XCVR 0x00000080 /* Port A Transceiver select enable */ -#define GPCR_DIR_SERB_XCVR 0x00000040 /* Port B Transceiver select enable */ -#define GPCR_DIR_PHY_RST 0x00000020 /* ethernet PHY reset enable */ - -/* defs for some of the generic I/O pins */ -#define GPCR_PHY_RESET 0x20 /* pin is output to PHY reset */ -#define GPCR_UARTB_MODESEL 0x40 /* pin is output to port B mode sel */ -#define GPCR_UARTA_MODESEL 0x80 /* pin is output to port A mode sel */ - -#define GPPR_PHY_RESET_PIN 5 /* GIO pin controlling phy reset */ -#define GPPR_UARTB_MODESEL_PIN 6 /* GIO pin controlling uart b mode select */ -#define GPPR_UARTA_MODESEL_PIN 7 /* GIO pin controlling uart a mode select */ - -#define EMCR_DUPLEX 0x00000001 -#define EMCR_PROMISC 0x00000002 -#define EMCR_PADEN 0x00000004 -#define EMCR_RXOFF_MASK 0x000001f8 -#define EMCR_RXOFF_SHIFT 3 -#define EMCR_RAMPAR 0x00000200 -#define EMCR_BADPAR 0x00000800 -#define EMCR_BUFSIZ 0x00001000 -#define EMCR_TXDMAEN 0x00002000 -#define EMCR_TXEN 0x00004000 -#define EMCR_RXDMAEN 0x00008000 -#define EMCR_RXEN 0x00010000 -#define EMCR_LOOPBACK 0x00020000 -#define EMCR_ARB_DIAG 0x001c0000 -#define EMCR_ARB_DIAG_IDLE 0x00200000 -#define EMCR_RST 0x80000000 - -#define EISR_RXTIMERINT 0x00000001 -#define EISR_RXTHRESHINT 0x00000002 -#define EISR_RXOFLO 0x00000004 -#define EISR_RXBUFOFLO 0x00000008 -#define EISR_RXMEMERR 0x00000010 -#define EISR_RXPARERR 0x00000020 -#define EISR_TXEMPTY 0x00010000 -#define EISR_TXRTRY 0x00020000 -#define EISR_TXEXDEF 0x00040000 -#define EISR_TXLCOL 0x00080000 -#define EISR_TXGIANT 0x00100000 -#define EISR_TXBUFUFLO 0x00200000 -#define EISR_TXEXPLICIT 0x00400000 -#define EISR_TXCOLLWRAP 0x00800000 -#define EISR_TXDEFERWRAP 0x01000000 -#define EISR_TXMEMERR 0x02000000 -#define EISR_TXPARERR 0x04000000 - -#define ERCSR_THRESH_MASK 0x000001ff /* enet RX threshold */ -#define ERCSR_RX_TMR 0x40000000 /* simulation only */ -#define ERCSR_DIAG_OFLO 0x80000000 /* simulation only */ - -#define ERBR_ALIGNMENT 4096 -#define ERBR_L_RXRINGBASE_MASK 0xfffff000 - -#define ERBAR_BARRIER_BIT 0x0100 -#define ERBAR_RXBARR_MASK 0xffff0000 -#define ERBAR_RXBARR_SHIFT 16 - -#define ERCIR_RXCONSUME_MASK 0x00000fff - -#define ERPIR_RXPRODUCE_MASK 0x00000fff -#define ERPIR_ARM 0x80000000 - -#define ERTR_CNT_MASK 0x000007ff - -#define ETCSR_IPGT_MASK 0x0000007f -#define ETCSR_IPGR1_MASK 0x00007f00 -#define ETCSR_IPGR1_SHIFT 8 -#define ETCSR_IPGR2_MASK 0x007f0000 -#define ETCSR_IPGR2_SHIFT 16 -#define ETCSR_NOTXCLK 0x80000000 - -#define ETCDC_COLLCNT_MASK 0x0000ffff -#define ETCDC_DEFERCNT_MASK 0xffff0000 -#define ETCDC_DEFERCNT_SHIFT 16 - -#define ETBR_ALIGNMENT (64*1024) -#define ETBR_L_RINGSZ_MASK 0x00000001 -#define ETBR_L_RINGSZ128 0 -#define ETBR_L_RINGSZ512 1 -#define ETBR_L_TXRINGBASE_MASK 0xffffc000 - -#define ETCIR_TXCONSUME_MASK 0x0000ffff -#define ETCIR_IDLE 0x80000000 - -#define ETPIR_TXPRODUCE_MASK 0x0000ffff - -#define EBIR_TXBUFPROD_MASK 0x0000001f -#define EBIR_TXBUFCONS_MASK 0x00001f00 -#define EBIR_TXBUFCONS_SHIFT 8 -#define EBIR_RXBUFPROD_MASK 0x007fc000 -#define EBIR_RXBUFPROD_SHIFT 14 -#define EBIR_RXBUFCONS_MASK 0xff800000 -#define EBIR_RXBUFCONS_SHIFT 23 - -#define MICR_REGADDR_MASK 0x0000001f -#define MICR_PHYADDR_MASK 0x000003e0 -#define MICR_PHYADDR_SHIFT 5 -#define MICR_READTRIG 0x00000400 -#define MICR_BUSY 0x00000800 - -#define MIDR_DATA_MASK 0x0000ffff - -#define ERXBUF_IPCKSUM_MASK 0x0000ffff -#define ERXBUF_BYTECNT_MASK 0x07ff0000 -#define ERXBUF_BYTECNT_SHIFT 16 -#define ERXBUF_V 0x80000000 - -#define ERXBUF_CRCERR 0x00000001 /* aka RSV15 */ -#define ERXBUF_FRAMERR 0x00000002 /* aka RSV14 */ -#define ERXBUF_CODERR 0x00000004 /* aka RSV13 */ -#define ERXBUF_INVPREAMB 0x00000008 /* aka RSV18 */ -#define ERXBUF_LOLEN 0x00007000 /* aka RSV2_0 */ -#define ERXBUF_HILEN 0x03ff0000 /* aka RSV12_3 */ -#define ERXBUF_MULTICAST 0x04000000 /* aka RSV16 */ -#define ERXBUF_BROADCAST 0x08000000 /* aka RSV17 */ -#define ERXBUF_LONGEVENT 0x10000000 /* aka RSV19 */ -#define ERXBUF_BADPKT 0x20000000 /* aka RSV20 */ -#define ERXBUF_GOODPKT 0x40000000 /* aka RSV21 */ -#define ERXBUF_CARRIER 0x80000000 /* aka RSV22 */ - -#define ETXD_BYTECNT_MASK 0x000007ff /* total byte count */ -#define ETXD_INTWHENDONE 0x00001000 /* intr when done */ -#define ETXD_D0V 0x00010000 /* data 0 valid */ -#define ETXD_B1V 0x00020000 /* buf 1 valid */ -#define ETXD_B2V 0x00040000 /* buf 2 valid */ -#define ETXD_DOCHECKSUM 0x00080000 /* insert ip cksum */ -#define ETXD_CHKOFF_MASK 0x07f00000 /* cksum byte offset */ -#define ETXD_CHKOFF_SHIFT 20 - -#define ETXD_D0CNT_MASK 0x0000007f -#define ETXD_B1CNT_MASK 0x0007ff00 -#define ETXD_B1CNT_SHIFT 8 -#define ETXD_B2CNT_MASK 0x7ff00000 -#define ETXD_B2CNT_SHIFT 20 - -typedef enum ioc3_subdevs_e { - ioc3_subdev_ether, - ioc3_subdev_generic, - ioc3_subdev_nic, - ioc3_subdev_kbms, - ioc3_subdev_ttya, - ioc3_subdev_ttyb, - ioc3_subdev_ecpp, - ioc3_subdev_rt, - ioc3_nsubdevs -} ioc3_subdev_t; - -/* subdevice disable bits, - * from the standard INFO_LBL_SUBDEVS - */ -#define IOC3_SDB_ETHER (1<