/* * linux/arch/arm/drivers/scsi/fas216.c * * Copyright (C) 1997-2000 Russell King * * Based on information in qlogicfas.c by Tom Zerucha, Michael Griffith, and * other sources, including: * the AMD Am53CF94 data sheet * the AMD Am53C94 data sheet * * This is a generic driver. To use it, have a look at cumana_2.c. You * should define your own structure that overlays FAS216_Info, eg: * struct my_host_data { * FAS216_Info info; * ... my host specific data ... * }; * * Changelog: * 30-08-1997 RMK Created * 14-09-1997 RMK Started disconnect support * 08-02-1998 RMK Corrected real DMA support * 15-02-1998 RMK Started sync xfer support * 06-04-1998 RMK Tightened conditions for printing incomplete * transfers * 02-05-1998 RMK Added extra checks in fas216_reset * 24-05-1998 RMK Fixed synchronous transfers with period >= 200ns * 27-06-1998 RMK Changed asm/delay.h to linux/delay.h * 26-08-1998 RMK Improved message support wrt MESSAGE_REJECT * 02-04-2000 RMK Converted to use the new error handling, and * automatically request sense data upon check * condition status from targets. * * Todo: * - allow individual devices to enable sync xfers. */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #define FAS216_C #include "../../scsi/scsi.h" #include "../../scsi/hosts.h" #include "fas216.h" MODULE_AUTHOR("Russell King"); MODULE_DESCRIPTION("Generic FAS216/NCR53C9x driver"); #define VER_MAJOR 0 #define VER_MINOR 0 #define VER_PATCH 5 /* NOTE: SCSI2 Synchronous transfers *require* DMA according to * the data sheet. This restriction is crazy, especially when * you only want to send 16 bytes! What were the guys who * designed this chip on at that time? Did they read the SCSI2 * spec at all? The following sections are taken from the SCSI2 * standard (s2r10) concerning this: * * > IMPLEMENTORS NOTES: * > (1) Re-negotiation at every selection is not recommended, since a * > significant performance impact is likely. * * > The implied synchronous agreement shall remain in effect until a BUS DEVICE * > RESET message is received, until a hard reset condition occurs, or until one * > of the two SCSI devices elects to modify the agreement. The default data * > transfer mode is asynchronous data transfer mode. The default data transfer * > mode is entered at power on, after a BUS DEVICE RESET message, or after a hard * > reset condition. * * In total, this means that once you have elected to use synchronous * transfers, you must always use DMA. * * I was thinking that this was a good chip until I found this restriction ;( */ #define SCSI2_SYNC #undef SCSI2_WIDE #undef SCSI2_TAG #undef DEBUG_CONNECT #undef DEBUG_BUSSERVICE #undef DEBUG_FUNCTIONDONE #undef DEBUG_MESSAGES #undef CHECK_STRUCTURE static struct { int stat, ssr, isr, ph; } list[8]; static int ptr; static void fas216_dumpstate(FAS216_Info *info) { unsigned char is, stat, inst; is = inb(REG_IS(info)); stat = inb(REG_STAT(info)); inst = inb(REG_INST(info)); printk("FAS216: CTCL=%02X CTCM=%02X CMD=%02X STAT=%02X" " INST=%02X IS=%02X CFIS=%02X", inb(REG_CTCL(info)), inb(REG_CTCM(info)), inb(REG_CMD(info)), stat, inst, is, inb(REG_CFIS(info))); printk(" CNTL1=%02X CNTL2=%02X CNTL3=%02X CTCH=%02X\n", inb(REG_CNTL1(info)), inb(REG_CNTL2(info)), inb(REG_CNTL3(info)), inb(REG_CTCH(info))); } static void fas216_dumpinfo(FAS216_Info *info) { static int used = 0; int i; if (used++) return; printk("FAS216_Info=\n"); printk(" { magic_start=%lX host=%p SCpnt=%p origSCpnt=%p\n", info->magic_start, info->host, info->SCpnt, info->origSCpnt); printk(" scsi={ io_port=%X io_shift=%X irq=%X cfg={ %X %X %X %X }\n", info->scsi.io_port, info->scsi.io_shift, info->scsi.irq, info->scsi.cfg[0], info->scsi.cfg[1], info->scsi.cfg[2], info->scsi.cfg[3]); printk(" type=%p phase=%X reconnected={ target=%d lun=%d tag=%d }\n", info->scsi.type, info->scsi.phase, info->scsi.reconnected.target, info->scsi.reconnected.lun, info->scsi.reconnected.tag); printk(" SCp={ ptr=%p this_residual=%X buffer=%p buffers_residual=%X }\n", info->scsi.SCp.ptr, info->scsi.SCp.this_residual, info->scsi.SCp.buffer, info->scsi.SCp.buffers_residual); printk(" msgs async_stp=%X disconnectable=%d aborting=%d }\n", info->scsi.async_stp, info->scsi.disconnectable, info->scsi.aborting); printk(" stats={ queues=%X removes=%X fins=%X reads=%X writes=%X miscs=%X\n" " disconnects=%X aborts=%X bus_resets=%X host_resets=%X}\n", info->stats.queues, info->stats.removes, info->stats.fins, info->stats.reads, info->stats.writes, info->stats.miscs, info->stats.disconnects, info->stats.aborts, info->stats.bus_resets, info->stats.host_resets); printk(" ifcfg={ clockrate=%X select_timeout=%X asyncperiod=%X sync_max_depth=%X }\n", info->ifcfg.clockrate, info->ifcfg.select_timeout, info->ifcfg.asyncperiod, info->ifcfg.sync_max_depth); for (i = 0; i < 8; i++) { printk(" busyluns[%d]=%X dev[%d]={ disconnect_ok=%d stp=%X sof=%X sync_state=%X }\n", i, info->busyluns[i], i, info->device[i].disconnect_ok, info->device[i].stp, info->device[i].sof, info->device[i].sync_state); } printk(" dma={ transfer_type=%X setup=%p pseudo=%p stop=%p }\n", info->dma.transfer_type, info->dma.setup, info->dma.pseudo, info->dma.stop); printk(" internal_done=%X magic_end=%lX }\n", info->internal_done, info->magic_end); } #ifdef CHECK_STRUCTURE static void __fas216_checkmagic(FAS216_Info *info, const char *func) { int corruption = 0; if (info->magic_start != MAGIC) { printk(KERN_CRIT "FAS216 Error: magic at start corrupted\n"); corruption++; } if (info->magic_end != MAGIC) { printk(KERN_CRIT "FAS216 Error: magic at end corrupted\n"); corruption++; } if (corruption) { fas216_dumpinfo(info); panic("scsi memory space corrupted in %s", func); } } #define fas216_checkmagic(info) __fas216_checkmagic((info), __FUNCTION__) #else #define fas216_checkmagic(info) #endif static const char *fas216_bus_phase(int stat) { static const char *phases[] = { "DATA OUT", "DATA IN", "COMMAND", "STATUS", "MISC OUT", "MISC IN", "MESG OUT", "MESG IN" }; return phases[stat & STAT_BUSMASK]; } static const char *fas216_drv_phase(FAS216_Info *info) { switch (info->scsi.phase) { case PHASE_IDLE: return "idle"; case PHASE_SELECTION: return "selection"; case PHASE_COMMAND: return "command"; case PHASE_RECONNECTED: return "reconnected"; case PHASE_DATAOUT: return "data out"; case PHASE_DATAIN: return "data in"; case PHASE_MSGIN: return "message in"; case PHASE_MSGIN_DISCONNECT: return "disconnect"; case PHASE_MSGOUT_EXPECT: return "expect message out"; case PHASE_MSGOUT: return "message out"; case PHASE_STATUS: return "status"; case PHASE_DONE: return "done"; default: return "???"; } } static char fas216_target(FAS216_Info *info) { if (info->SCpnt) return '0' + info->SCpnt->target; else return 'H'; } static void add_debug_list(int stat, int ssr, int isr, int ph) { list[ptr].stat = stat; list[ptr].ssr = ssr; list[ptr].isr = isr; list[ptr].ph = ph; ptr = (ptr + 1) & 7; } static void print_debug_list(void) { int i; i = ptr; printk(KERN_ERR "SCSI IRQ trail: "); do { printk("%02X:%02X:%02X:%1X ", list[i].stat, list[i].ssr, list[i].isr, list[i].ph); i = (i + 1) & 7; } while (i != ptr); printk("\n"); } static void fas216_done(FAS216_Info *info, unsigned int result); /* Function: int fas216_clockrate(unsigned int clock) * Purpose : calculate correct value to be written into clock conversion * factor register. * Params : clock - clock speed in MHz * Returns : CLKF_ value */ static int fas216_clockrate(int clock) { if (clock <= 10 || clock > 40) { printk(KERN_CRIT "fas216: invalid clock rate: check your driver!\n"); clock = -1; } else clock = ((clock - 1) / 5 + 1) & 7; return clock; } /* Function: unsigned short fas216_get_last_msg(FAS216_Info *info, int pos) * Purpose : retrieve a last message from the list, using position in fifo * Params : info - interface to search * : pos - current fifo position */ static inline unsigned short fas216_get_last_msg(FAS216_Info *info, int pos) { unsigned short packed_msg = NOP; struct message *msg; int msgnr = 0; while ((msg = msgqueue_getmsg(&info->scsi.msgs, msgnr++)) != NULL) { if (pos >= msg->fifo) break; } if (msg) { if (msg->msg[0] == EXTENDED_MESSAGE) packed_msg = EXTENDED_MESSAGE | msg->msg[2] << 8; else packed_msg = msg->msg[0]; } #ifdef DEBUG_MESSAGES printk("Message: %04X found at position %02X\n", packed_msg, pos); #endif return packed_msg; } /* Function: int fas216_syncperiod(FAS216_Info *info, int ns) * Purpose : Calculate value to be loaded into the STP register * for a given period in ns * Params : info - state structure for interface connected to device * : ns - period in ns (between subsequent bytes) * Returns : Value suitable for REG_STP */ static int fas216_syncperiod(FAS216_Info *info, int ns) { int value = (info->ifcfg.clockrate * ns) / 1000; fas216_checkmagic(info); if (value < 4) value = 4; else if (value > 35) value = 35; return value & 31; } /* Function: void fas216_set_sync(FAS216_Info *info, int target) * Purpose : Correctly setup FAS216 chip for specified transfer period. * Params : info - state structure for interface * : target - target * Notes : we need to switch the chip out of FASTSCSI mode if we have * a transfer period >= 200ns - otherwise the chip will violate * the SCSI timings. */ static void fas216_set_sync(FAS216_Info *info, int target) { outb(info->device[target].sof, REG_SOF(info)); outb(info->device[target].stp, REG_STP(info)); if (info->device[target].period >= (200 / 4)) outb(info->scsi.cfg[2] & ~CNTL3_FASTSCSI, REG_CNTL3(info)); else outb(info->scsi.cfg[2], REG_CNTL3(info)); } /* Synchronous transfer support * * Note: The SCSI II r10 spec says (5.6.12): * * (2) Due to historical problems with early host adapters that could * not accept an SDTR message, some targets may not initiate synchronous * negotiation after a power cycle as required by this standard. Host * adapters that support synchronous mode may avoid the ensuing failure * modes when the target is independently power cycled by initiating a * synchronous negotiation on each REQUEST SENSE and INQUIRY command. * This approach increases the SCSI bus overhead and is not recommended * for new implementations. The correct method is to respond to an * SDTR message with a MESSAGE REJECT message if the either the * initiator or target devices does not support synchronous transfers * or does not want to negotiate for synchronous transfers at the time. * Using the correct method assures compatibility with wide data * transfers and future enhancements. * * We will always initiate a synchronous transfer negociation request on * every INQUIRY or REQUEST SENSE message, unless the target itself has * at some point performed a synchronous transfer negociation request, or * we have synchronous transfers disabled for this device. */ /* Function: void fas216_handlesync(FAS216_Info *info, char *msg) * Purpose : Handle a synchronous transfer message from the target * Params : info - state structure for interface * : msg - message from target */ static void fas216_handlesync(FAS216_Info *info, char *msg) { struct fas216_device *dev = &info->device[info->SCpnt->target]; enum { sync, async, none, reject } res = none; #ifdef SCSI2_SYNC switch (msg[0]) { case MESSAGE_REJECT: /* Synchronous transfer request failed. * Note: SCSI II r10: * * SCSI devices that are capable of synchronous * data transfers shall not respond to an SDTR * message with a MESSAGE REJECT message. * * Hence, if we get this condition, we disable * negociation for this device. */ if (dev->sync_state == neg_inprogress) { dev->sync_state = neg_invalid; res = async; } break; case EXTENDED_MESSAGE: switch (dev->sync_state) { /* We don't accept synchronous transfer requests. * Respond with a MESSAGE_REJECT to prevent a * synchronous transfer agreement from being reached. */ case neg_invalid: res = reject; break; /* We were not negociating a synchronous transfer, * but the device sent us a negociation request. * Honour the request by sending back a SDTR * message containing our capability, limited by * the targets capability. */ default: outb(CMD_SETATN, REG_CMD(info)); if (msg[4] > info->ifcfg.sync_max_depth) msg[4] = info->ifcfg.sync_max_depth; if (msg[3] < 1000 / info->ifcfg.clockrate) msg[3] = 1000 / info->ifcfg.clockrate; msgqueue_flush(&info->scsi.msgs); msgqueue_addmsg(&info->scsi.msgs, 5, EXTENDED_MESSAGE, 3, EXTENDED_SDTR, msg[3], msg[4]); info->scsi.phase = PHASE_MSGOUT_EXPECT; /* This is wrong. The agreement is not in effect * until this message is accepted by the device */ dev->sync_state = neg_targcomplete; res = sync; break; /* We initiated the synchronous transfer negociation, * and have successfully received a response from the * target. The synchronous transfer agreement has been * reached. Note: if the values returned are out of our * bounds, we must reject the message. */ case neg_inprogress: res = reject; if (msg[4] <= info->ifcfg.sync_max_depth && msg[3] >= 1000 / info->ifcfg.clockrate) { dev->sync_state = neg_complete; res = sync; } break; } } #else res = reject; #endif switch (res) { case sync: dev->period = msg[3]; dev->sof = msg[4]; dev->stp = fas216_syncperiod(info, msg[3] * 4); fas216_set_sync(info, info->SCpnt->target); break; case reject: outb(CMD_SETATN, REG_CMD(info)); msgqueue_flush(&info->scsi.msgs); msgqueue_addmsg(&info->scsi.msgs, 1, MESSAGE_REJECT); info->scsi.phase = PHASE_MSGOUT_EXPECT; case async: dev->period = info->ifcfg.asyncperiod / 4; dev->sof = 0; dev->stp = info->scsi.async_stp; fas216_set_sync(info, info->SCpnt->target); break; case none: break; } } /* Function: void fas216_handlewide(FAS216_Info *info, char *msg) * Purpose : Handle a wide transfer message from the target * Params : info - state structure for interface * : msg - message from target */ static void fas216_handlewide(FAS216_Info *info, char *msg) { struct fas216_device *dev = &info->device[info->SCpnt->target]; enum { wide, bit8, none, reject } res = none; #ifdef SCSI2_WIDE switch (msg[0]) { case MESSAGE_REJECT: /* Wide transfer request failed. * Note: SCSI II r10: * * SCSI devices that are capable of wide * data transfers shall not respond to a * WDTR message with a MESSAGE REJECT message. * * Hence, if we get this condition, we never * reattempt negociation for this device. */ if (dev->wide_state == neg_inprogress) { dev->wide_state = neg_invalid; res = bit8; } break; case EXTENDED_MESSAGE: switch (dev->wide_state) { /* We don't accept wide data transfer requests. * Respond with a MESSAGE REJECT to prevent a * wide data transfer agreement from being reached. */ case neg_invalid: res = reject; break; /* We were not negociating a wide data transfer, * but the device sent is a negociation request. * Honour the request by sending back a WDTR * message containing our capability, limited by * the targets capability. */ default: outb(CMD_SETATN, REG_CMD(info)); if (msg[3] > info->ifcfg.wide_max_size) msg[3] = info->ifcfg.wide_max_size; msgqueue_flush(&info->scsi.msgs); msgqueue_addmsg(&info->scsi.msgs, 4, EXTENDED_MESSAGE, 2, EXTENDED_WDTR, msg[3]); info->scsi.phase = PHASE_MSGOUT_EXPECT; res = wide; break; /* We initiated the wide data transfer negociation, * and have successfully received a response from the * target. The synchronous transfer agreement has been * reached. Note: if the values returned are out of our * bounds, we must reject the message. */ case neg_inprogress: res = reject; if (msg[3] <= info->ifcfg.wide_max_size) { dev->wide_state = neg_complete; res = wide; } break; } } #else res = reject; #endif switch (res) { case wide: dev->wide_xfer = msg[3]; break; case reject: outb(CMD_SETATN, REG_CMD(info)); msgqueue_flush(&info->scsi.msgs); msgqueue_addmsg(&info->scsi.msgs, 1, MESSAGE_REJECT); info->scsi.phase = PHASE_MSGOUT_EXPECT; case bit8: dev->wide_xfer = 0; break; case none: break; } } /* Function: void fas216_updateptrs(FAS216_Info *info, int bytes_transferred) * Purpose : update data pointers after transfer suspended/paused * Params : info - interface's local pointer to update * bytes_transferred - number of bytes transferred */ static void fas216_updateptrs(FAS216_Info *info, int bytes_transferred) { unsigned char *ptr; unsigned int residual; fas216_checkmagic(info); ptr = info->scsi.SCp.ptr; residual = info->scsi.SCp.this_residual; info->SCpnt->request_bufflen -= bytes_transferred; while (residual <= bytes_transferred && bytes_transferred) { /* We have used up this buffer */ bytes_transferred -= residual; if (info->scsi.SCp.buffers_residual) { info->scsi.SCp.buffer++; info->scsi.SCp.buffers_residual--; ptr = (unsigned char *)info->scsi.SCp.buffer->address; residual = info->scsi.SCp.buffer->length; } else { ptr = NULL; residual = 0; } } residual -= bytes_transferred; ptr += bytes_transferred; if (residual == 0) ptr = NULL; info->scsi.SCp.ptr = ptr; info->scsi.SCp.this_residual = residual; } /* Function: void fas216_pio(FAS216_Info *info, fasdmadir_t direction) * Purpose : transfer data off of/on to card using programmed IO * Params : info - interface to transfer data to/from * direction - direction to transfer data (DMA_OUT/DMA_IN) * Notes : this is incredibly slow */ static void fas216_pio(FAS216_Info *info, fasdmadir_t direction) { unsigned int residual; char *ptr; fas216_checkmagic(info); residual = info->scsi.SCp.this_residual; ptr = info->scsi.SCp.ptr; if (direction == DMA_OUT) outb(*ptr++, REG_FF(info)); else *ptr++ = inb(REG_FF(info)); residual -= 1; if (residual == 0) { if (info->scsi.SCp.buffers_residual) { info->scsi.SCp.buffer++; info->scsi.SCp.buffers_residual--; ptr = (unsigned char *)info->scsi.SCp.buffer->address; residual = info->scsi.SCp.buffer->length; } else { ptr = NULL; residual = 0; } } info->scsi.SCp.ptr = ptr; info->scsi.SCp.this_residual = residual; } /* Function: void fas216_starttransfer(FAS216_Info *info, * fasdmadir_t direction) * Purpose : Start a DMA/PIO transfer off of/on to card * Params : info - interface from which device disconnected from * direction - transfer direction (DMA_OUT/DMA_IN) */ static void fas216_starttransfer(FAS216_Info *info, fasdmadir_t direction, int flush_fifo) { fasdmatype_t dmatype; fas216_checkmagic(info); info->scsi.phase = (direction == DMA_OUT) ? PHASE_DATAOUT : PHASE_DATAIN; if (info->dma.transfer_type != fasdma_none && info->dma.transfer_type != fasdma_pio) { unsigned long total, residual; if (info->dma.transfer_type == fasdma_real_all) total = info->SCpnt->request_bufflen; else total = info->scsi.SCp.this_residual; residual = (inb(REG_CFIS(info)) & CFIS_CF) + inb(REG_CTCL(info)) + (inb(REG_CTCM(info)) << 8) + (inb(REG_CTCH(info)) << 16); fas216_updateptrs(info, total - residual); } info->dma.transfer_type = fasdma_none; if (!info->scsi.SCp.ptr) { printk("scsi%d.%c: null buffer passed to " "fas216_starttransfer\n", info->host->host_no, fas216_target(info)); return; } /* flush FIFO */ if (flush_fifo) outb(CMD_FLUSHFIFO, REG_CMD(info)); /* * Default to PIO mode or DMA mode if we have a synchronous * transfer agreement. */ if (info->device[info->SCpnt->target].sof && info->dma.setup) dmatype = fasdma_real_all; else dmatype = fasdma_pio; if (info->dma.setup) dmatype = info->dma.setup(info->host, &info->scsi.SCp, direction, dmatype); info->dma.transfer_type = dmatype; switch (dmatype) { case fasdma_pio: outb(0, REG_SOF(info)); outb(info->scsi.async_stp, REG_STP(info)); outb(info->scsi.SCp.this_residual, REG_STCL(info)); outb(info->scsi.SCp.this_residual >> 8, REG_STCM(info)); outb(info->scsi.SCp.this_residual >> 16, REG_STCH(info)); outb(CMD_TRANSFERINFO, REG_CMD(info)); fas216_pio(info, direction); break; case fasdma_pseudo: outb(info->scsi.SCp.this_residual, REG_STCL(info)); outb(info->scsi.SCp.this_residual >> 8, REG_STCM(info)); outb(info->scsi.SCp.this_residual >> 16, REG_STCH(info)); outb(CMD_TRANSFERINFO | CMD_WITHDMA, REG_CMD(info)); info->dma.pseudo(info->host, &info->scsi.SCp, direction, info->SCpnt->transfersize); break; case fasdma_real_block: outb(info->scsi.SCp.this_residual, REG_STCL(info)); outb(info->scsi.SCp.this_residual >> 8, REG_STCM(info)); outb(info->scsi.SCp.this_residual >> 16, REG_STCH(info)); outb(CMD_TRANSFERINFO | CMD_WITHDMA, REG_CMD(info)); break; case fasdma_real_all: outb(info->SCpnt->request_bufflen, REG_STCL(info)); outb(info->SCpnt->request_bufflen >> 8, REG_STCM(info)); outb(info->SCpnt->request_bufflen >> 16, REG_STCH(info)); outb(CMD_TRANSFERINFO | CMD_WITHDMA, REG_CMD(info)); break; default: printk(KERN_ERR "scsi%d.%d: invalid FAS216 DMA type\n", info->host->host_no, fas216_target(info)); break; } } /* Function: void fas216_stoptransfer(FAS216_Info *info) * Purpose : Stop a DMA transfer onto / off of the card * Params : info - interface from which device disconnected from */ static void fas216_stoptransfer(FAS216_Info *info) { fas216_checkmagic(info); if (info->dma.transfer_type != fasdma_none && info->dma.transfer_type != fasdma_pio) { unsigned long total, residual; if ((info->dma.transfer_type == fasdma_real_all || info->dma.transfer_type == fasdma_real_block) && info->dma.stop) info->dma.stop(info->host, &info->scsi.SCp); if (info->dma.transfer_type == fasdma_real_all) total = info->SCpnt->request_bufflen; else total = info->scsi.SCp.this_residual; residual = (inb(REG_CFIS(info)) & CFIS_CF) + inb(REG_CTCL(info)) + (inb(REG_CTCM(info)) << 8) + (inb(REG_CTCH(info)) << 16); fas216_updateptrs(info, total - residual); info->dma.transfer_type = fasdma_none; } if (info->scsi.phase == PHASE_DATAOUT) outb(CMD_FLUSHFIFO, REG_CMD(info)); } /* Function: void fas216_disconnected_intr(FAS216_Info *info) * Purpose : handle device disconnection * Params : info - interface from which device disconnected from */ static void fas216_disconnect_intr(FAS216_Info *info) { fas216_checkmagic(info); #ifdef DEBUG_CONNECT printk("scsi%d.%c: disconnect phase=%02X\n", info->host->host_no, fas216_target(info), info->scsi.phase); #endif msgqueue_flush(&info->scsi.msgs); switch (info->scsi.phase) { case PHASE_SELECTION: /* while selecting - no target */ case PHASE_SELSTEPS: fas216_done(info, DID_NO_CONNECT); break; case PHASE_MSGIN_DISCONNECT: /* message in - disconnecting */ outb(CMD_ENABLESEL, REG_CMD(info)); info->scsi.disconnectable = 1; info->scsi.reconnected.tag = 0; info->scsi.phase = PHASE_IDLE; info->stats.disconnects += 1; break; case PHASE_DONE: /* at end of command - complete */ fas216_done(info, DID_OK); break; case PHASE_MSGOUT: /* message out - possible ABORT message */ if (fas216_get_last_msg(info, info->scsi.msgin_fifo) == ABORT) { info->scsi.aborting = 0; fas216_done(info, DID_ABORT); break; } default: /* huh? */ printk(KERN_ERR "scsi%d.%c: unexpected disconnect in phase %s\n", info->host->host_no, fas216_target(info), fas216_drv_phase(info)); print_debug_list(); fas216_stoptransfer(info); fas216_done(info, DID_ERROR); break; } } /* Function: void fas216_reselected_intr(FAS216_Info *info) * Purpose : Start reconnection of a device * Params : info - interface which was reselected */ static void fas216_reselected_intr(FAS216_Info *info) { unsigned char target, identify_msg, ok; fas216_checkmagic(info); if ((info->scsi.phase == PHASE_SELECTION || info->scsi.phase == PHASE_SELSTEPS) && info->SCpnt) { Scsi_Cmnd *SCpnt = info->SCpnt; info->origSCpnt = SCpnt; info->SCpnt = NULL; if (info->device[SCpnt->target].wide_state == neg_inprogress) info->device[SCpnt->target].wide_state = neg_wait; if (info->device[SCpnt->target].sync_state == neg_inprogress) info->device[SCpnt->target].sync_state = neg_wait; } #ifdef DEBUG_CONNECT printk("scsi%d.%c: reconnect phase=%02X\n", info->host->host_no, fas216_target(info), info->scsi.phase); #endif if ((inb(REG_CFIS(info)) & CFIS_CF) != 2) { printk(KERN_ERR "scsi%d.H: incorrect number of bytes after reselect\n", info->host->host_no); outb(CMD_SETATN, REG_CMD(info)); outb(CMD_MSGACCEPTED, REG_CMD(info)); msgqueue_flush(&info->scsi.msgs); msgqueue_addmsg(&info->scsi.msgs, 1, INITIATOR_ERROR); info->scsi.phase = PHASE_MSGOUT_EXPECT; return; } target = inb(REG_FF(info)); identify_msg = inb(REG_FF(info)); ok = 1; if (!(target & (1 << info->host->this_id))) { printk(KERN_ERR "scsi%d.H: invalid host id on reselect\n", info->host->host_no); ok = 0; } if (!(identify_msg & 0x80)) { printk(KERN_ERR "scsi%d.H: no IDENTIFY message on reselect, got msg %02X\n", info->host->host_no, identify_msg); ok = 0; } if (!ok) { /* * Something went wrong - send an initiator error to * the target. */ outb(CMD_SETATN, REG_CMD(info)); outb(CMD_MSGACCEPTED, REG_CMD(info)); msgqueue_flush(&info->scsi.msgs); msgqueue_addmsg(&info->scsi.msgs, 1, INITIATOR_ERROR); info->scsi.phase = PHASE_MSGOUT_EXPECT; return; } target &= ~(1 << info->host->this_id); switch (target) { case 1: target = 0; break; case 2: target = 1; break; case 4: target = 2; break; case 8: target = 3; break; case 16: target = 4; break; case 32: target = 5; break; case 64: target = 6; break; case 128: target = 7; break; default: target = info->host->this_id; break; } identify_msg &= 7; info->scsi.reconnected.target = target; info->scsi.reconnected.lun = identify_msg; info->scsi.reconnected.tag = 0; ok = 0; if (info->scsi.disconnectable && info->SCpnt && info->SCpnt->target == target && info->SCpnt->lun == identify_msg) ok = 1; if (!ok && queue_probetgtlun(&info->queues.disconnected, target, identify_msg)) ok = 1; msgqueue_flush(&info->scsi.msgs); if (ok) { info->scsi.phase = PHASE_RECONNECTED; outb(target, REG_SDID(info)); } else { /* * Our command structure not found - abort the * command on the target. Since we have no * record of this command, we can't send * an INITIATOR DETECTED ERROR message. */ outb(CMD_SETATN, REG_CMD(info)); msgqueue_addmsg(&info->scsi.msgs, 1, ABORT); info->scsi.phase = PHASE_MSGOUT_EXPECT; } outb(CMD_MSGACCEPTED, REG_CMD(info)); } /* Function: void fas216_finish_reconnect(FAS216_Info *info) * Purpose : finish reconnection sequence for device * Params : info - interface which caused function done interrupt */ static void fas216_finish_reconnect(FAS216_Info *info) { fas216_checkmagic(info); #ifdef DEBUG_CONNECT printk("Connected: %1X %1X %02X, reconnected: %1X %1X %02X\n", info->SCpnt->target, info->SCpnt->lun, info->SCpnt->tag, info->scsi.reconnected.target, info->scsi.reconnected.lun, info->scsi.reconnected.tag); #endif if (info->scsi.disconnectable && info->SCpnt) { info->scsi.disconnectable = 0; if (info->SCpnt->target == info->scsi.reconnected.target && info->SCpnt->lun == info->scsi.reconnected.lun && info->SCpnt->tag == info->scsi.reconnected.tag) { #ifdef DEBUG_CONNECT printk("scsi%d.%c: reconnected", info->host->host_no, fas216_target(info)); #endif } else { queue_add_cmd_tail(&info->queues.disconnected, info->SCpnt); #ifdef DEBUG_CONNECT printk("scsi%d.%c: had to move command to disconnected queue\n", info->host->host_no, fas216_target(info)); #endif info->SCpnt = NULL; } } if (!info->SCpnt) { info->SCpnt = queue_remove_tgtluntag(&info->queues.disconnected, info->scsi.reconnected.target, info->scsi.reconnected.lun, info->scsi.reconnected.tag); #ifdef DEBUG_CONNECT printk("scsi%d.%c: had to get command", info->host->host_no, fas216_target(info)); #endif } if (!info->SCpnt) { outb(CMD_SETATN, REG_CMD(info)); msgqueue_flush(&info->scsi.msgs); #if 0 if (info->scsi.reconnected.tag) msgqueue_addmsg(&info->scsi.msgs, 2, ABORT_TAG, info->scsi.reconnected.tag); else #endif msgqueue_addmsg(&info->scsi.msgs, 1, ABORT); info->scsi.phase = PHASE_MSGOUT_EXPECT; info->scsi.aborting = 1; } else { /* * Restore data pointer from SAVED data pointer */ info->scsi.SCp = info->SCpnt->SCp; #ifdef DEBUG_CONNECT printk(", data pointers: [%p, %X]", info->scsi.SCp.ptr, info->scsi.SCp.this_residual); #endif } #ifdef DEBUG_CONNECT printk("\n"); #endif } static int fas216_wait_cmd(FAS216_Info *info, int cmd) { int tout; int stat; outb(cmd, REG_CMD(info)); for (tout = 1000; tout; tout -= 1) { stat = inb(REG_STAT(info)); if (stat & STAT_INT) break; udelay(1); } return stat; } static int fas216_get_msg_byte(FAS216_Info *info) { int stat; stat = fas216_wait_cmd(info, CMD_MSGACCEPTED); if ((stat & STAT_INT) == 0) goto timedout; if ((stat & STAT_BUSMASK) != STAT_MESGIN) goto unexpected_phase_change; inb(REG_INST(info)); stat = fas216_wait_cmd(info, CMD_TRANSFERINFO); if ((stat & STAT_INT) == 0) goto timedout; if ((stat & STAT_BUSMASK) != STAT_MESGIN) goto unexpected_phase_change; inb(REG_INST(info)); return inb(REG_FF(info)); timedout: printk("scsi%d.%c: timed out waiting for message byte\n", info->host->host_no, fas216_target(info)); return -1; unexpected_phase_change: printk("scsi%d.%c: unexpected phase change: status = %02X\n", info->host->host_no, fas216_target(info), stat); return -2; } /* Function: void fas216_message(FAS216_Info *info) * Purpose : handle a function done interrupt from FAS216 chip * Params : info - interface which caused function done interrupt */ static void fas216_message(FAS216_Info *info) { unsigned char *message = info->scsi.message; unsigned int msglen = 1, i; int msgbyte = 0; fas216_checkmagic(info); message[0] = inb(REG_FF(info)); if (message[0] == EXTENDED_MESSAGE) { msgbyte = fas216_get_msg_byte(info); if (msgbyte >= 0) { message[1] = msgbyte; for (msglen = 2; msglen < message[1] + 2; msglen++) { msgbyte = fas216_get_msg_byte(info); if (msgbyte >= 0) message[msglen] = msgbyte; else break; } } } info->scsi.msglen = msglen; #ifdef DEBUG_MESSAGES { int i; printk("scsi%d.%c: message in: ", info->host->host_no, fas216_target(info)); for (i = 0; i < msglen; i++) printk("%02X ", message[i]); printk("\n"); } #endif if (info->scsi.phase == PHASE_RECONNECTED) { if (message[0] == SIMPLE_QUEUE_TAG) info->scsi.reconnected.tag = message[1]; fas216_finish_reconnect(info); info->scsi.phase = PHASE_MSGIN; } switch (message[0]) { case COMMAND_COMPLETE: if (msglen != 1) goto unrecognised; printk(KERN_ERR "scsi%d.%c: command complete with no " "status in MESSAGE_IN?\n", info->host->host_no, fas216_target(info)); break; case SAVE_POINTERS: if (msglen != 1) goto unrecognised; /* * Save current data pointer to SAVED data pointer * SCSI II standard says that we must not acknowledge * this until we have really saved pointers. * NOTE: we DO NOT save the command nor status pointers * as required by the SCSI II standard. These always * point to the start of their respective areas. */ info->SCpnt->SCp = info->scsi.SCp; info->SCpnt->SCp.sent_command = 0; #if defined (DEBUG_MESSAGES) || defined (DEBUG_CONNECT) printk("scsi%d.%c: save data pointers: [%p, %X]\n", info->host->host_no, fas216_target(info), info->scsi.SCp.ptr, info->scsi.SCp.this_residual); #endif break; case RESTORE_POINTERS: if (msglen != 1) goto unrecognised; /* * Restore current data pointer from SAVED data pointer */ info->scsi.SCp = info->SCpnt->SCp; #if defined (DEBUG_MESSAGES) || defined (DEBUG_CONNECT) printk("scsi%d.%c: restore data pointers: [%p, %X]\n", info->host->host_no, fas216_target(info), info->scsi.SCp.ptr, info->scsi.SCp.this_residual); #endif break; case DISCONNECT: if (msglen != 1) goto unrecognised; info->scsi.phase = PHASE_MSGIN_DISCONNECT; break; case MESSAGE_REJECT: if (msglen != 1) goto unrecognised; switch (fas216_get_last_msg(info, info->scsi.msgin_fifo)) { case EXTENDED_MESSAGE | EXTENDED_SDTR << 8: fas216_handlesync(info, message); break; case EXTENDED_MESSAGE | EXTENDED_WDTR << 8: fas216_handlewide(info, message); break; default: printk("scsi%d.%c: reject, last message %04X\n", info->host->host_no, fas216_target(info), fas216_get_last_msg(info, info->scsi.msgin_fifo)); } break; case NOP: break; case SIMPLE_QUEUE_TAG: if (msglen < 2) goto unrecognised; /* handled above - print a warning since this is untested */ printk("scsi%d.%c: reconnect queue tag %02X\n", info->host->host_no, fas216_target(info), message[1]); break; case EXTENDED_MESSAGE: if (msglen < 3) goto unrecognised; switch (message[2]) { case EXTENDED_SDTR: /* Sync transfer negociation request/reply */ fas216_handlesync(info, message); break; case EXTENDED_WDTR: /* Wide transfer negociation request/reply */ fas216_handlewide(info, message); break; default: goto unrecognised; } break; default: goto unrecognised; } outb(CMD_MSGACCEPTED, REG_CMD(info)); return; unrecognised: printk("scsi%d.%c: unrecognised message, rejecting\n", info->host->host_no, fas216_target(info)); printk("scsi%d.%c: message was", info->host->host_no, fas216_target(info)); for (i = 0; i < msglen; i++) printk("%s%02X", i & 31 ? " " : "\n ", message[i]); printk("\n"); /* * Something strange seems to be happening here - * I can't use SETATN since the chip gives me an * invalid command interrupt when I do. Weird. */ outb(CMD_NOP, REG_CMD(info)); fas216_dumpstate(info); outb(CMD_SETATN, REG_CMD(info)); msgqueue_flush(&info->scsi.msgs); msgqueue_addmsg(&info->scsi.msgs, 1, MESSAGE_REJECT); info->scsi.phase = PHASE_MSGOUT_EXPECT; fas216_dumpstate(info); outb(CMD_MSGACCEPTED, REG_CMD(info)); } /* Function: void fas216_send_command(FAS216_Info *info) * Purpose : send a command to a target after all message bytes have been sent * Params : info - interface which caused bus service */ static void fas216_send_command(FAS216_Info *info) { int i; fas216_checkmagic(info); outb(CMD_NOP|CMD_WITHDMA, REG_CMD(info)); outb(CMD_FLUSHFIFO, REG_CMD(info)); /* load command */ for (i = info->scsi.SCp.sent_command; i < info->SCpnt->cmd_len; i++) outb(info->SCpnt->cmnd[i], REG_FF(info)); outb(CMD_TRANSFERINFO, REG_CMD(info)); info->scsi.phase = PHASE_COMMAND; } /* Function: void fas216_send_messageout(FAS216_Info *info, int start) * Purpose : handle bus service to send a message * Params : info - interface which caused bus service * Note : We do not allow the device to change the data direction! */ static void fas216_send_messageout(FAS216_Info *info, int start) { unsigned int tot_msglen = msgqueue_msglength(&info->scsi.msgs); fas216_checkmagic(info); outb(CMD_FLUSHFIFO, REG_CMD(info)); if (tot_msglen) { struct message *msg; int msgnr = 0; while ((msg = msgqueue_getmsg(&info->scsi.msgs, msgnr++)) != NULL) { int i; for (i = start; i < msg->length; i++) outb(msg->msg[i], REG_FF(info)); msg->fifo = tot_msglen - (inb(REG_CFIS(info)) & CFIS_CF); start = 0; } } else outb(NOP, REG_FF(info)); outb(CMD_TRANSFERINFO, REG_CMD(info)); info->scsi.phase = PHASE_MSGOUT; } /* Function: void fas216_busservice_intr(FAS216_Info *info, unsigned int stat, unsigned int ssr) * Purpose : handle a bus service interrupt from FAS216 chip * Params : info - interface which caused bus service interrupt * stat - Status register contents * ssr - SCSI Status register contents */ static void fas216_busservice_intr(FAS216_Info *info, unsigned int stat, unsigned int ssr) { fas216_checkmagic(info); #ifdef DEBUG_BUSSERVICE printk("scsi%d.%c: bus service: stat=%02X ssr=%02X phase=%02X\n", info->host->host_no, fas216_target(info), stat, ssr, info->scsi.phase); #endif switch (info->scsi.phase) { case PHASE_SELECTION: if ((ssr & IS_BITS) != 1) goto bad_is; break; case PHASE_SELSTEPS: switch (ssr & IS_BITS) { case IS_SELARB: case IS_MSGBYTESENT: goto bad_is; case IS_NOTCOMMAND: case IS_EARLYPHASE: if ((stat & STAT_BUSMASK) == STAT_MESGIN) break; goto bad_is; case IS_COMPLETE: break; } default: break; } outb(CMD_NOP, REG_CMD(info)); #define STATE(st,ph) ((ph) << 3 | (st)) /* This table describes the legal SCSI state transitions, * as described by the SCSI II spec. */ switch (STATE(stat & STAT_BUSMASK, info->scsi.phase)) { /* Reselmsgin -> Data In */ case STATE(STAT_DATAIN, PHASE_RECONNECTED): fas216_finish_reconnect(info); case STATE(STAT_DATAIN, PHASE_SELSTEPS):/* Sel w/ steps -> Data In */ case STATE(STAT_DATAIN, PHASE_DATAIN): /* Data In -> Data In */ case STATE(STAT_DATAIN, PHASE_MSGOUT): /* Message Out -> Data In */ case STATE(STAT_DATAIN, PHASE_COMMAND): /* Command -> Data In */ case STATE(STAT_DATAIN, PHASE_MSGIN): /* Message In -> Data In */ fas216_starttransfer(info, DMA_IN, 0); return; case STATE(STAT_DATAOUT, PHASE_DATAOUT):/* Data Out -> Data Out */ fas216_starttransfer(info, DMA_OUT, 0); return; /* Reselmsgin -> Data Out */ case STATE(STAT_DATAOUT, PHASE_RECONNECTED): fas216_finish_reconnect(info); case STATE(STAT_DATAOUT, PHASE_SELSTEPS):/* Sel w/ steps-> Data Out */ case STATE(STAT_DATAOUT, PHASE_MSGOUT): /* Message Out -> Data Out */ case STATE(STAT_DATAOUT, PHASE_COMMAND):/* Command -> Data Out */ case STATE(STAT_DATAOUT, PHASE_MSGIN): /* Message In -> Data Out */ fas216_starttransfer(info, DMA_OUT, 1); return; /* Reselmsgin -> Status */ case STATE(STAT_STATUS, PHASE_RECONNECTED): fas216_finish_reconnect(info); goto status; case STATE(STAT_STATUS, PHASE_DATAOUT): /* Data Out -> Status */ case STATE(STAT_STATUS, PHASE_DATAIN): /* Data In -> Status */ fas216_stoptransfer(info); case STATE(STAT_STATUS, PHASE_SELSTEPS):/* Sel w/ steps -> Status */ case STATE(STAT_STATUS, PHASE_MSGOUT): /* Message Out -> Status */ case STATE(STAT_STATUS, PHASE_COMMAND): /* Command -> Status */ case STATE(STAT_STATUS, PHASE_MSGIN): /* Message In -> Status */ status: outb(CMD_INITCMDCOMPLETE, REG_CMD(info)); info->scsi.phase = PHASE_STATUS; return; case STATE(STAT_MESGIN, PHASE_DATAOUT): /* Data Out -> Message In */ case STATE(STAT_MESGIN, PHASE_DATAIN): /* Data In -> Message In */ fas216_stoptransfer(info); case STATE(STAT_MESGIN, PHASE_COMMAND): /* Command -> Message In */ case STATE(STAT_MESGIN, PHASE_SELSTEPS):/* Sel w/ steps -> Message In */ case STATE(STAT_MESGIN, PHASE_MSGOUT): /* Message Out -> Message In */ info->scsi.msgin_fifo = inb(REG_CFIS(info)) & CFIS_CF; outb(CMD_FLUSHFIFO, REG_CMD(info)); outb(CMD_TRANSFERINFO, REG_CMD(info)); info->scsi.phase = PHASE_MSGIN; return; /* Reselmsgin -> Message In */ case STATE(STAT_MESGIN, PHASE_RECONNECTED): case STATE(STAT_MESGIN, PHASE_MSGIN): info->scsi.msgin_fifo = inb(REG_CFIS(info)) & CFIS_CF; outb(CMD_TRANSFERINFO, REG_CMD(info)); return; /* Reselmsgin -> Command */ case STATE(STAT_COMMAND, PHASE_RECONNECTED): fas216_finish_reconnect(info); case STATE(STAT_COMMAND, PHASE_MSGOUT): /* Message Out -> Command */ case STATE(STAT_COMMAND, PHASE_MSGIN): /* Message In -> Command */ fas216_send_command(info); info->scsi.phase = PHASE_COMMAND; return; /* Selection -> Message Out */ case STATE(STAT_MESGOUT, PHASE_SELECTION): fas216_send_messageout(info, 1); return; /* Any -> Message Out */ case STATE(STAT_MESGOUT, PHASE_MSGOUT_EXPECT): fas216_send_messageout(info, 0); return; /* Error recovery rules. * These either attempt to abort or retry the operation. * TODO: we need more of these */ case STATE(STAT_COMMAND, PHASE_COMMAND):/* Command -> Command */ /* error - we've sent out all the command bytes * we have. * NOTE: we need SAVE DATA POINTERS/RESTORE DATA POINTERS * to include the command bytes sent for this to work * correctly. */ printk(KERN_ERR "scsi%d.%c: " "target trying to receive more command bytes\n", info->host->host_no, fas216_target(info)); outb(CMD_SETATN, REG_CMD(info)); outb(15, REG_STCL(info)); outb(0, REG_STCM(info)); outb(0, REG_STCH(info)); outb(CMD_PADBYTES | CMD_WITHDMA, REG_CMD(info)); msgqueue_flush(&info->scsi.msgs); msgqueue_addmsg(&info->scsi.msgs, 1, INITIATOR_ERROR); info->scsi.phase = PHASE_MSGOUT_EXPECT; return; /* Selection -> Message Out */ case STATE(STAT_MESGOUT, PHASE_SELSTEPS): case STATE(STAT_MESGOUT, PHASE_MSGOUT): /* Message Out -> Message Out */ /* If we get another message out phase, this * usually means some parity error occurred. * Resend complete set of messages. If we have * more than 1 byte to send, we need to assert * ATN again. */ if (msgqueue_msglength(&info->scsi.msgs) > 1) outb(CMD_SETATN, REG_CMD(info)); fas216_send_messageout(info, 0); return; } if (info->scsi.phase == PHASE_MSGIN_DISCONNECT) { printk(KERN_ERR "scsi%d.%c: disconnect message received, but bus service %s?\n", info->host->host_no, fas216_target(info), fas216_bus_phase(stat)); msgqueue_flush(&info->scsi.msgs); outb(CMD_SETATN, REG_CMD(info)); msgqueue_addmsg(&info->scsi.msgs, 1, INITIATOR_ERROR); info->scsi.phase = PHASE_MSGOUT_EXPECT; info->scsi.aborting = 1; outb(CMD_TRANSFERINFO, REG_CMD(info)); return; } printk(KERN_ERR "scsi%d.%c: bus phase %s after %s?\n", info->host->host_no, fas216_target(info), fas216_bus_phase(stat), fas216_drv_phase(info)); print_debug_list(); return; bad_is: printk("scsi%d.%c: bus service at step %d?\n", info->host->host_no, fas216_target(info), ssr & IS_BITS); print_debug_list(); fas216_done(info, DID_ERROR); } /* Function: void fas216_funcdone_intr(FAS216_Info *info, unsigned int stat, unsigned int ssr) * Purpose : handle a function done interrupt from FAS216 chip * Params : info - interface which caused function done interrupt * stat - Status register contents * ssr - SCSI Status register contents */ static void fas216_funcdone_intr(FAS216_Info *info, unsigned int stat, unsigned int ssr) { int status, message; fas216_checkmagic(info); #ifdef DEBUG_FUNCTIONDONE printk("scsi%d.%c: function done: stat=%X ssr=%X phase=%02X\n", info->host->host_no, fas216_target(info), stat, ssr, info->scsi.phase); #endif switch (info->scsi.phase) { case PHASE_STATUS: /* status phase - read status and msg */ status = inb(REG_FF(info)); message = inb(REG_FF(info)); info->scsi.SCp.Message = message; info->scsi.SCp.Status = status; info->scsi.phase = PHASE_DONE; outb(CMD_MSGACCEPTED, REG_CMD(info)); break; case PHASE_IDLE: /* reselected? */ case PHASE_MSGIN: /* message in phase */ case PHASE_RECONNECTED: /* reconnected command */ if ((stat & STAT_BUSMASK) == STAT_MESGIN) { info->scsi.msgin_fifo = inb(REG_CFIS(info)) & CFIS_CF; fas216_message(info); break; } default: printk("scsi%d.%c: internal phase %s for function done?" " What do I do with this?\n", info->host->host_no, fas216_target(info), fas216_drv_phase(info)); } } /* Function: void fas216_intr(struct Scsi_Host *instance) * Purpose : handle interrupts from the interface to progress a command * Params : instance - interface to service */ void fas216_intr(struct Scsi_Host *instance) { FAS216_Info *info = (FAS216_Info *)instance->hostdata; unsigned char isr, ssr, stat; fas216_checkmagic(info); stat = inb(REG_STAT(info)); ssr = inb(REG_IS(info)); isr = inb(REG_INST(info)); add_debug_list(stat, ssr, isr, info->scsi.phase); if (stat & STAT_INT) { if (isr & INST_BUSRESET) { printk(KERN_DEBUG "scsi%d.H: bus reset detected\n", instance->host_no); scsi_report_bus_reset(instance, 0); } else if (isr & INST_ILLEGALCMD) { printk(KERN_CRIT "scsi%d.H: illegal command given\n", instance->host_no); fas216_dumpstate(info); } else if (isr & INST_DISCONNECT) fas216_disconnect_intr(info); else if (isr & INST_RESELECTED) /* reselected */ fas216_reselected_intr(info); else if (isr & INST_BUSSERVICE) /* bus service request */ fas216_busservice_intr(info, stat, ssr); else if (isr & INST_FUNCDONE) /* function done */ fas216_funcdone_intr(info, stat, ssr); else printk("scsi%d.%c: unknown interrupt received:" " phase %s isr %02X ssr %02X stat %02X\n", instance->host_no, fas216_target(info), fas216_drv_phase(info), isr, ssr, stat); } } /* Function: void fas216_kick(FAS216_Info *info) * Purpose : kick a command to the interface - interface should be idle * Params : info - our host interface to kick * Notes : Interrupts are always disabled! */ static void fas216_kick(FAS216_Info *info) { Scsi_Cmnd *SCpnt = NULL; int tot_msglen, from_queue = 0, disconnect_ok; fas216_checkmagic(info); /* * Obtain the next command to process. */ do { if (info->reqSCpnt) { SCpnt = info->reqSCpnt; info->reqSCpnt = NULL; break; } if (info->origSCpnt) { SCpnt = info->origSCpnt; info->origSCpnt = NULL; break; } /* retrieve next command */ if (!SCpnt) { SCpnt = queue_remove_exclude(&info->queues.issue, info->busyluns); from_queue = 1; break; } } while (0); if (!SCpnt) /* no command pending - just exit */ return; if (info->scsi.disconnectable && info->SCpnt) { queue_add_cmd_tail(&info->queues.disconnected, info->SCpnt); info->scsi.disconnectable = 0; info->SCpnt = NULL; printk("scsi%d.%c: moved command to disconnected queue\n", info->host->host_no, fas216_target(info)); } /* * claim host busy */ info->scsi.phase = PHASE_SELECTION; info->SCpnt = SCpnt; info->scsi.SCp = SCpnt->SCp; info->dma.transfer_type = fasdma_none; #ifdef DEBUG_CONNECT printk("scsi%d.%c: starting cmd %02X", info->host->host_no, '0' + SCpnt->target, SCpnt->cmnd[0]); #endif if (from_queue) { #ifdef SCSI2_TAG /* * tagged queuing - allocate a new tag to this command */ if (SCpnt->device->tagged_queue && SCpnt->cmnd[0] != REQUEST_SENSE && SCpnt->cmnd[0] != INQUIRY) { SCpnt->device->current_tag += 1; if (SCpnt->device->current_tag == 0) SCpnt->device->current_tag = 1; SCpnt->tag = SCpnt->device->current_tag; } else #endif set_bit(SCpnt->target * 8 + SCpnt->lun, info->busyluns); info->stats.removes += 1; switch (SCpnt->cmnd[0]) { case WRITE_6: case WRITE_10: case WRITE_12: info->stats.writes += 1; break; case READ_6: case READ_10: case READ_12: info->stats.reads += 1; break; default: info->stats.miscs += 1; break; } } /* * Don't allow request sense commands to disconnect. */ disconnect_ok = SCpnt->cmnd[0] != REQUEST_SENSE && info->device[SCpnt->target].disconnect_ok; /* * build outgoing message bytes */ msgqueue_flush(&info->scsi.msgs); msgqueue_addmsg(&info->scsi.msgs, 1, IDENTIFY(disconnect_ok, SCpnt->lun)); /* * add tag message if required */ if (SCpnt->tag) msgqueue_addmsg(&info->scsi.msgs, 2, SIMPLE_QUEUE_TAG, SCpnt->tag); do { #ifdef SCSI2_WIDE if (info->device[SCpnt->target].wide_state == neg_wait) { info->device[SCpnt->target].wide_state = neg_inprogress; msgqueue_addmsg(&info->scsi.msgs, 4, EXTENDED_MESSAGE, 2, EXTENDED_WDTR, info->ifcfg.wide_max_size); break; } #endif #ifdef SCSI2_SYNC if ((info->device[SCpnt->target].sync_state == neg_wait || info->device[SCpnt->target].sync_state == neg_complete) && (SCpnt->cmnd[0] == REQUEST_SENSE || SCpnt->cmnd[0] == INQUIRY)) { info->device[SCpnt->target].sync_state = neg_inprogress; msgqueue_addmsg(&info->scsi.msgs, 5, EXTENDED_MESSAGE, 3, EXTENDED_SDTR, 1000 / info->ifcfg.clockrate, info->ifcfg.sync_max_depth); break; } #endif } while (0); /* following what the ESP driver says */ outb(0, REG_STCL(info)); outb(0, REG_STCM(info)); outb(0, REG_STCH(info)); outb(CMD_NOP | CMD_WITHDMA, REG_CMD(info)); /* flush FIFO */ outb(CMD_FLUSHFIFO, REG_CMD(info)); /* load bus-id and timeout */ outb(BUSID(SCpnt->target), REG_SDID(info)); outb(info->ifcfg.select_timeout, REG_STIM(info)); /* synchronous transfers */ fas216_set_sync(info, SCpnt->target); tot_msglen = msgqueue_msglength(&info->scsi.msgs); #ifdef DEBUG_MESSAGES { struct message *msg; int msgnr = 0, i; printk("scsi%d.%c: message out: ", info->host->host_no, '0' + SCpnt->target); while ((msg = msgqueue_getmsg(&info->scsi.msgs, msgnr++)) != NULL) { printk("{ "); for (i = 0; i < msg->length; i++) printk("%02x ", msg->msg[i]); printk("} "); } printk("\n"); } #endif if (tot_msglen == 1 || tot_msglen == 3) { /* * We have an easy message length to send... */ struct message *msg; int msgnr = 0, i; info->scsi.phase = PHASE_SELSTEPS; /* load message bytes */ while ((msg = msgqueue_getmsg(&info->scsi.msgs, msgnr++)) != NULL) { for (i = 0; i < msg->length; i++) outb(msg->msg[i], REG_FF(info)); msg->fifo = tot_msglen - (inb(REG_CFIS(info)) & CFIS_CF); } /* load command */ for (i = 0; i < SCpnt->cmd_len; i++) outb(SCpnt->cmnd[i], REG_FF(info)); if (tot_msglen == 1) outb(CMD_SELECTATN, REG_CMD(info)); else outb(CMD_SELECTATN3, REG_CMD(info)); } else { /* * We have an unusual number of message bytes to send. * Load first byte into fifo, and issue SELECT with ATN and * stop steps. */ struct message *msg = msgqueue_getmsg(&info->scsi.msgs, 0); outb(msg->msg[0], REG_FF(info)); msg->fifo = 1; outb(CMD_SELECTATNSTOP, REG_CMD(info)); } #ifdef DEBUG_CONNECT printk(", data pointers [%p, %X]\n", info->scsi.SCp.ptr, info->scsi.SCp.this_residual); #endif /* should now get either DISCONNECT or (FUNCTION DONE with BUS SERVICE) intr */ } /* Function: void fas216_rq_sns_done(info, SCpnt, result) * Purpose : Finish processing automatic request sense command * Params : info - interface that completed * SCpnt - command that completed * result - driver byte of result */ static void fas216_rq_sns_done(FAS216_Info *info, Scsi_Cmnd *SCpnt, unsigned int result) { #ifdef DEBUG_CONNECT printk("scsi%d.%c: request sense complete, result=%04X%02X%02X\n", info->host->host_no, '0' + SCpnt->target, result, SCpnt->SCp.Message, SCpnt->SCp.Status); #endif if (result != DID_OK || SCpnt->SCp.Status != GOOD) /* * Something went wrong. Make sure that we don't * have valid data in the sense buffer that could * confuse the higher levels. */ memset(SCpnt->sense_buffer, 0, sizeof(SCpnt->sense_buffer)); /* * Note that we don't set SCpnt->result, since that should * reflect the status of the command that we were asked by * the upper layers to process. This would have been set * correctly by fas216_std_done. */ SCpnt->scsi_done(SCpnt); } /* Function: void fas216_std_done(info, SCpnt, result) * Purpose : Finish processing of standard command * Params : info - interface that completed * SCpnt - command that completed * result - driver byte of result */ static void fas216_std_done(FAS216_Info *info, Scsi_Cmnd *SCpnt, unsigned int result) { info->stats.fins += 1; SCpnt->result = result << 16 | info->scsi.SCp.Message << 8 | info->scsi.SCp.Status; #ifdef DEBUG_CONNECT printk("scsi%d.%c: command complete, result=%08X, command=", info->host->host_no, '0' + SCpnt->target, SCpnt->result); print_command(SCpnt->cmnd); #endif /* * If the driver detected an error, or the command * was request sense, then we're all done. */ if (result != DID_OK || SCpnt->cmnd[0] == REQUEST_SENSE) goto done; /* * If the command returned CHECK_CONDITION status, * request the sense information. */ if (info->scsi.SCp.Status == CHECK_CONDITION) goto request_sense; /* * If the command did not complete with GOOD status, * we are all done here. */ if (info->scsi.SCp.Status != GOOD) goto done; /* * We have successfully completed a command. Make sure that * we do not have any buffers left to transfer. The world * is not perfect, and we seem to occasionally hit this. * It can be indicative of a buggy driver, target or the upper * levels of the SCSI code. */ if (info->scsi.SCp.ptr) { switch (SCpnt->cmnd[0]) { case INQUIRY: case START_STOP: // case READ_CAPACITY: case MODE_SENSE: break; default: printk(KERN_ERR "scsi%d.%c: incomplete data transfer " "detected: res=%08X ptr=%p len=%X command=", info->host->host_no, '0' + SCpnt->target, SCpnt->result, info->scsi.SCp.ptr, info->scsi.SCp.this_residual); print_command(SCpnt->cmnd); } } done: SCpnt->scsi_done(SCpnt); return; request_sense: memset(SCpnt->cmnd, 0, sizeof (SCpnt->cmnd)); SCpnt->cmnd[0] = REQUEST_SENSE; SCpnt->cmnd[1] = SCpnt->lun << 5; SCpnt->cmnd[4] = sizeof(SCpnt->sense_buffer); SCpnt->cmd_len = COMMAND_SIZE(SCpnt->cmnd[0]); SCpnt->SCp.buffer = NULL; SCpnt->SCp.buffers_residual = 0; SCpnt->SCp.ptr = (char *)SCpnt->sense_buffer; SCpnt->SCp.this_residual = sizeof(SCpnt->sense_buffer); SCpnt->SCp.Message = 0; SCpnt->SCp.Status = 0; SCpnt->sc_data_direction = SCSI_DATA_READ; SCpnt->use_sg = 0; SCpnt->tag = 0; SCpnt->host_scribble = (void *)fas216_rq_sns_done; /* * Place this command into the high priority "request * sense" slot. This will be the very next command * executed, unless a target connects to us. */ if (info->reqSCpnt) printk(KERN_WARNING "scsi%d.%c: loosing request command\n", info->host->host_no, '0' + SCpnt->target); info->reqSCpnt = SCpnt; } /* Function: void fas216_done(FAS216_Info *info, unsigned int result) * Purpose : complete processing for current command * Params : info - interface that completed * result - driver byte of result */ static void fas216_done(FAS216_Info *info, unsigned int result) { void (*fn)(FAS216_Info *, Scsi_Cmnd *, unsigned int); Scsi_Cmnd *SCpnt; fas216_checkmagic(info); if (!info->SCpnt) goto no_command; SCpnt = info->SCpnt; info->SCpnt = NULL; info->scsi.phase = PHASE_IDLE; if (!SCpnt->scsi_done) goto no_done; if (info->scsi.aborting) { printk("scsi%d.%c: uncaught abort - returning DID_ABORT\n", info->host->host_no, fas216_target(info)); result = DID_ABORT; info->scsi.aborting = 0; } /* * Sanity check the completion - if we have zero bytes left * to transfer, we should not have a valid pointer. */ if (info->scsi.SCp.ptr && info->scsi.SCp.this_residual == 0) { printk("scsi%d.%c: zero bytes left to transfer, but " "buffer pointer still valid: ptr=%p len=%08x command=", info->host->host_no, '0' + SCpnt->target, info->scsi.SCp.ptr, info->scsi.SCp.this_residual); info->scsi.SCp.ptr = NULL; print_command(SCpnt->cmnd); } /* * Clear down this command as completed. If we need to request * the sense information, fas216_kick will re-assert the busy * status. */ clear_bit(SCpnt->target * 8 + SCpnt->lun, info->busyluns); fn = (void (*)(FAS216_Info *, Scsi_Cmnd *, unsigned int))SCpnt->host_scribble; fn(info, SCpnt, result); if (info->scsi.irq != NO_IRQ) fas216_kick(info); return; no_command: panic("scsi%d.H: null command in fas216_done", info->host->host_no); no_done: panic("scsi%d.H: null scsi_done function in fas216_done", info->host->host_no); } /* Function: int fas216_queue_command(Scsi_Cmnd *SCpnt, void (*done)(Scsi_Cmnd *)) * Purpose : queue a command for adapter to process. * Params : SCpnt - Command to queue * done - done function to call once command is complete * Returns : 0 - success, else error * Notes : io_request_lock is held, interrupts are disabled. */ int fas216_queue_command(Scsi_Cmnd *SCpnt, void (*done)(Scsi_Cmnd *)) { FAS216_Info *info = (FAS216_Info *)SCpnt->host->hostdata; int result; fas216_checkmagic(info); #ifdef DEBUG_CONNECT printk("scsi%d.%c: received queuable command (%p) %02X\n", SCpnt->host->host_no, '0' + SCpnt->target, SCpnt, SCpnt->cmnd[0]); #endif SCpnt->scsi_done = done; SCpnt->host_scribble = (void *)fas216_std_done; SCpnt->result = 0; SCpnt->SCp.Message = 0; SCpnt->SCp.Status = 0; if (SCpnt->use_sg) { unsigned long len = 0; int buf; SCpnt->SCp.buffer = (struct scatterlist *) SCpnt->buffer; SCpnt->SCp.buffers_residual = SCpnt->use_sg - 1; SCpnt->SCp.ptr = (char *) SCpnt->SCp.buffer->address; SCpnt->SCp.this_residual = SCpnt->SCp.buffer->length; /* * Calculate correct buffer length. Some commands * come in with the wrong request_bufflen. */ for (buf = 0; buf <= SCpnt->SCp.buffers_residual; buf++) len += SCpnt->SCp.buffer[buf].length; if (SCpnt->request_bufflen != len) printk(KERN_WARNING "scsi%d.%c: bad request buffer " "length %d, should be %ld\n", info->host->host_no, '0' + SCpnt->target, SCpnt->request_bufflen, len); SCpnt->request_bufflen = len; } else { SCpnt->SCp.buffer = NULL; SCpnt->SCp.buffers_residual = 0; SCpnt->SCp.ptr = (unsigned char *)SCpnt->request_buffer; SCpnt->SCp.this_residual = SCpnt->request_bufflen; } /* * If the upper SCSI layers pass a buffer, but zero length, * we aren't interested in the buffer pointer. */ if (SCpnt->SCp.this_residual == 0 && SCpnt->SCp.ptr) { #if 0 printk(KERN_WARNING "scsi%d.%c: zero length buffer passed for " "command ", info->host->host_no, '0' + SCpnt->target); print_command(SCpnt->cmnd); #endif SCpnt->SCp.ptr = NULL; } info->stats.queues += 1; SCpnt->tag = 0; /* * Add command into execute queue and let it complete under * whatever scheme we're using. */ result = !queue_add_cmd_ordered(&info->queues.issue, SCpnt); /* * If we successfully added the command, * kick the interface to get it moving. */ if (result == 0 && (!info->SCpnt || info->scsi.disconnectable)) fas216_kick(info); return result; } /* Function: void fas216_internal_done(Scsi_Cmnd *SCpnt) * Purpose : trigger restart of a waiting thread in fas216_command * Params : SCpnt - Command to wake */ static void fas216_internal_done(Scsi_Cmnd *SCpnt) { FAS216_Info *info = (FAS216_Info *)SCpnt->host->hostdata; fas216_checkmagic(info); info->internal_done = 1; } /* Function: int fas216_command(Scsi_Cmnd *SCpnt) * Purpose : queue a command for adapter to process. * Params : SCpnt - Command to queue * Returns : scsi result code * Notes : io_request_lock is held, interrupts are disabled. */ int fas216_command(Scsi_Cmnd *SCpnt) { FAS216_Info *info = (FAS216_Info *)SCpnt->host->hostdata; fas216_checkmagic(info); /* * We should only be using this if we don't have an interrupt. * Provide some "incentive" to use the queueing code. */ if (info->scsi.irq != NO_IRQ) BUG(); info->internal_done = 0; fas216_queue_command(SCpnt, fas216_internal_done); /* * This wastes time, since we can't return until the command is * complete. We can't sleep either since we may get re-entered! * However, we must re-enable interrupts, or else we'll be * waiting forever. */ spin_unlock_irq(&io_request_lock); while (!info->internal_done) { /* * If we don't have an IRQ, then we must poll the card for * it's interrupt, and use that to call this driver's * interrupt routine. That way, we keep the command * progressing. Maybe we can add some inteligence here * and go to sleep if we know that the device is going * to be some time (eg, disconnected). */ if (inb(REG_STAT(info)) & STAT_INT) { spin_lock_irq(&io_request_lock); fas216_intr(info->host); spin_unlock_irq(&io_request_lock); } } spin_lock_irq(&io_request_lock); return SCpnt->result; } enum res_abort { res_failed, /* unable to abort */ res_success, /* command on issue queue */ res_success_clear, /* command marked tgt/lun busy */ res_hw_abort /* command on disconnected dev */ }; /* * Prototype: enum res_abort fas216_do_abort(FAS216_Info *info, Scsi_Cmnd *SCpnt) * Purpose : decide how to abort a command * Params : SCpnt - command to abort * Returns : abort status */ static enum res_abort fas216_do_abort(FAS216_Info *info, Scsi_Cmnd *SCpnt) { enum res_abort res = res_failed; if (queue_removecmd(&info->queues.issue, SCpnt)) { /* * The command was on the issue queue, and has not been * issued yet. We can remove the command from the queue, * and acknowledge the abort. Neither the device nor the * interface know about the command. */ printk("on issue queue "); res = res_success; } else if (queue_removecmd(&info->queues.disconnected, SCpnt)) { /* * The command was on the disconnected queue. We must * reconnect with the device if possible, and send it * an abort message. */ printk("on disconnected queue "); res = res_hw_abort; } else if (info->SCpnt == SCpnt) { printk("executing "); switch (info->scsi.phase) { /* * If the interface is idle, and the command is 'disconnectable', * then it is the same as on the disconnected queue. */ case PHASE_IDLE: if (info->scsi.disconnectable) { info->scsi.disconnectable = 0; info->SCpnt = NULL; res = res_hw_abort; } break; default: break; } } else if (info->origSCpnt == SCpnt) { /* * The command will be executed next, but a command * is currently using the interface. This is similar to * being on the issue queue, except the busylun bit has * been set. */ info->origSCpnt = NULL; printk("waiting for execution "); res = res_success_clear; } else printk("unknown "); return res; } /* Function: int fas216_eh_abort(Scsi_Cmnd *SCpnt) * Purpose : abort this command * Params : SCpnt - command to abort * Returns : FAILED if unable to abort * Notes : io_request_lock is taken, and irqs are disabled */ int fas216_eh_abort(Scsi_Cmnd *SCpnt) { FAS216_Info *info = (FAS216_Info *)SCpnt->host->hostdata; int result = FAILED; fas216_checkmagic(info); info->stats.aborts += 1; print_debug_list(); fas216_dumpstate(info); fas216_dumpinfo(info); printk(KERN_WARNING "scsi%d: abort ", info->host->host_no); switch (fas216_do_abort(info, SCpnt)) { /* * We managed to find the command and cleared it out. * We do not expect the command to be executing on the * target, but we have set the busylun bit. */ case res_success_clear: printk("clear "); clear_bit(SCpnt->target * 8 + SCpnt->lun, info->busyluns); /* * We found the command, and cleared it out. Either * the command is still known to be executing on the * target, or the busylun bit is not set. */ case res_success: printk("success\n"); result = SUCCESS; break; /* * We need to reconnect to the target and send it an * ABORT or ABORT_TAG message. We can only do this * if the bus is free. */ case res_hw_abort: /* * We are unable to abort the command for some reason. */ default: case res_failed: printk("failed\n"); break; } return result; } /* Function: void fas216_reset_state(FAS216_Info *info) * Purpose : Initialise driver internal state * Params : info - state to initialise */ static void fas216_reset_state(FAS216_Info *info) { neg_t sync_state, wide_state; int i; fas216_checkmagic(info); /* * Clear out all stale info in our state structure */ memset(info->busyluns, 0, sizeof(info->busyluns)); msgqueue_flush(&info->scsi.msgs); info->scsi.reconnected.target = 0; info->scsi.reconnected.lun = 0; info->scsi.reconnected.tag = 0; info->scsi.disconnectable = 0; info->scsi.aborting = 0; info->scsi.phase = PHASE_IDLE; info->scsi.async_stp = fas216_syncperiod(info, info->ifcfg.asyncperiod); if (info->ifcfg.wide_max_size == 0) wide_state = neg_invalid; else #ifdef SCSI2_WIDE wide_state = neg_wait; #else wide_state = neg_invalid; #endif if (info->host->dma_channel == NO_DMA || !info->dma.setup) sync_state = neg_invalid; else #ifdef SCSI2_SYNC sync_state = neg_wait; #else sync_state = neg_invalid; #endif for (i = 0; i < 8; i++) { info->device[i].disconnect_ok = info->ifcfg.disconnect_ok; info->device[i].sync_state = sync_state; info->device[i].wide_state = wide_state; info->device[i].period = info->ifcfg.asyncperiod / 4; info->device[i].stp = info->scsi.async_stp; info->device[i].sof = 0; info->device[i].wide_xfer = 0; } /* * Drain all commands on disconnected queue */ while (queue_remove(&info->queues.disconnected) != NULL); /* * Remove executing commands. */ info->SCpnt = NULL; info->reqSCpnt = NULL; info->origSCpnt = NULL; } /* Function: int fas216_eh_device_reset(Scsi_Cmnd *SCpnt) * Purpose : Reset the device associated with this command * Params : SCpnt - command specifing device to reset * Returns : FAILED if unable to reset */ int fas216_eh_device_reset(Scsi_Cmnd *SCpnt) { FAS216_Info *info = (FAS216_Info *)SCpnt->host->hostdata; printk("scsi%d.%c: "__FUNCTION__": called\n", info->host->host_no, '0' + SCpnt->target); return FAILED; } /* Function: int fas216_eh_bus_reset(Scsi_Cmnd *SCpnt) * Purpose : Reset the bus associated with the command * Params : SCpnt - command specifing bus to reset * Returns : FAILED if unable to reset * Notes : io_request_lock is taken, and irqs are disabled */ int fas216_eh_bus_reset(Scsi_Cmnd *SCpnt) { FAS216_Info *info = (FAS216_Info *)SCpnt->host->hostdata; int result = FAILED; fas216_checkmagic(info); info->stats.bus_resets += 1; printk("scsi%d.%c: "__FUNCTION__": resetting bus\n", info->host->host_no, '0' + SCpnt->target); /* * Attempt to stop all activity on this interface. */ outb(info->scsi.cfg[2], REG_CNTL3(info)); fas216_stoptransfer(info); /* * Clear any pending interrupts */ while (inb(REG_STAT(info)) & STAT_INT) inb(REG_INST(info)); /* * Reset the SCSI bus */ outb(CMD_RESETSCSI, REG_CMD(info)); udelay(5); /* * Clear reset interrupt */ if (inb(REG_STAT(info)) & STAT_INT && inb(REG_INST(info)) & INST_BUSRESET) result = SUCCESS; fas216_reset_state(info); return result; } /* Function: void fas216_init_chip(FAS216_Info *info) * Purpose : Initialise FAS216 state after reset * Params : info - state structure for interface */ static void fas216_init_chip(FAS216_Info *info) { outb(fas216_clockrate(info->ifcfg.clockrate), REG_CLKF(info)); outb(info->scsi.cfg[0], REG_CNTL1(info)); outb(info->scsi.cfg[1], REG_CNTL2(info)); outb(info->scsi.cfg[2], REG_CNTL3(info)); outb(info->ifcfg.select_timeout, REG_STIM(info)); outb(0, REG_SOF(info)); outb(info->scsi.async_stp, REG_STP(info)); outb(info->scsi.cfg[0], REG_CNTL1(info)); } /* Function: int fas216_eh_host_reset(Scsi_Cmnd *SCpnt) * Purpose : Reset the host associated with this command * Params : SCpnt - command specifing host to reset * Returns : FAILED if unable to reset * Notes : io_request_lock is taken, and irqs are disabled */ int fas216_eh_host_reset(Scsi_Cmnd *SCpnt) { FAS216_Info *info = (FAS216_Info *)SCpnt->host->hostdata; fas216_checkmagic(info); printk("scsi%d.%c: "__FUNCTION__": resetting host\n", info->host->host_no, '0' + SCpnt->target); /* * Reset the SCSI chip. */ outb(CMD_RESETCHIP, REG_CMD(info)); /* * Ugly ugly ugly! * We need to release the io_request_lock and enable * IRQs if we sleep, but we must relock and disable * IRQs after the sleep. */ spin_unlock_irq(&io_request_lock); scsi_sleep(5); spin_lock_irq(&io_request_lock); /* * Release the SCSI reset. */ outb(CMD_NOP, REG_CMD(info)); fas216_init_chip(info); return SUCCESS; } #define TYPE_UNKNOWN 0 #define TYPE_NCR53C90 1 #define TYPE_NCR53C90A 2 #define TYPE_NCR53C9x 3 #define TYPE_Am53CF94 4 #define TYPE_EmFAS216 5 #define TYPE_QLFAS216 6 static char *chip_types[] = { "unknown", "NS NCR53C90", "NS NCR53C90A", "NS NCR53C9x", "AMD Am53CF94", "Emulex FAS216", "QLogic FAS216" }; static int fas216_detect_type(FAS216_Info *info) { int family, rev; /* * Reset the chip. */ outb(CMD_RESETCHIP, REG_CMD(info)); udelay(50); outb(CMD_NOP, REG_CMD(info)); /* * Check to see if control reg 2 is present. */ outb(0, REG_CNTL3(info)); outb(CNTL2_S2FE, REG_CNTL2(info)); /* * If we are unable to read back control reg 2 * correctly, it is not present, and we have a * NCR53C90. */ if ((inb(REG_CNTL2(info)) & (~0xe0)) != CNTL2_S2FE) return TYPE_NCR53C90; /* * Now, check control register 3 */ outb(0, REG_CNTL2(info)); outb(0, REG_CNTL3(info)); outb(5, REG_CNTL3(info)); /* * If we are unable to read the register back * correctly, we have a NCR53C90A */ if (inb(REG_CNTL3(info)) != 5) return TYPE_NCR53C90A; /* * Now read the ID from the chip. */ outb(0, REG_CNTL3(info)); outb(CNTL3_ADIDCHK, REG_CNTL3(info)); outb(0, REG_CNTL3(info)); outb(CMD_RESETCHIP, REG_CMD(info)); udelay(5); outb(CMD_WITHDMA | CMD_NOP, REG_CMD(info)); outb(CNTL2_ENF, REG_CNTL2(info)); outb(CMD_RESETCHIP, REG_CMD(info)); udelay(5); outb(CMD_NOP, REG_CMD(info)); rev = inb(REG1_ID(info)); family = rev >> 3; rev &= 7; switch (family) { case 0x01: if (rev == 4) return TYPE_Am53CF94; break; case 0x02: switch (rev) { case 2: return TYPE_EmFAS216; case 3: return TYPE_QLFAS216; } break; default: break; } printk("family %x rev %x\n", family, rev); return TYPE_NCR53C9x; } /* Function: int fas216_init(struct Scsi_Host *instance) * Purpose : initialise FAS/NCR/AMD SCSI ic. * Params : instance - a driver-specific filled-out structure * Returns : 0 on success */ int fas216_init(struct Scsi_Host *instance) { FAS216_Info *info = (FAS216_Info *)instance->hostdata; int type; info->magic_start = MAGIC; info->magic_end = MAGIC; info->host = instance; info->scsi.cfg[0] = instance->this_id; info->scsi.cfg[1] = CNTL2_ENF | CNTL2_S2FE; info->scsi.cfg[2] = info->ifcfg.cntl3 | CNTL3_ADIDCHK | CNTL3_G2CB; memset(&info->stats, 0, sizeof(info->stats)); msgqueue_initialise(&info->scsi.msgs); if (!queue_initialise(&info->queues.issue)) return 1; if (!queue_initialise(&info->queues.disconnected)) { queue_free(&info->queues.issue); return 1; } fas216_reset_state(info); type = fas216_detect_type(info); info->scsi.type = chip_types[type]; udelay(300); /* * Initialise the chip correctly. */ fas216_init_chip(info); /* * Reset the SCSI bus. We don't want to see * the resulting reset interrupt, so mask it * out. */ outb(info->scsi.cfg[0] | CNTL1_DISR, REG_CNTL1(info)); outb(CMD_RESETSCSI, REG_CMD(info)); /* * scsi standard says wait 250ms */ spin_unlock_irq(&io_request_lock); scsi_sleep(5); spin_lock_irq(&io_request_lock); outb(info->scsi.cfg[0], REG_CNTL1(info)); inb(REG_INST(info)); fas216_checkmagic(info); return 0; } /* Function: int fas216_release(struct Scsi_Host *instance) * Purpose : release all resources and put everything to bed for * FAS/NCR/AMD SCSI ic. * Params : instance - a driver-specific filled-out structure * Returns : 0 on success */ int fas216_release(struct Scsi_Host *instance) { FAS216_Info *info = (FAS216_Info *)instance->hostdata; fas216_checkmagic(info); outb(CMD_RESETCHIP, REG_CMD(info)); queue_free(&info->queues.disconnected); queue_free(&info->queues.issue); return 0; } /* * Function: int fas216_info(FAS216_Info *info, char *buffer) * Purpose : generate a string containing information about this * host. * Params : info - FAS216 host information * buffer - string buffer to build string * Returns : size of built string */ int fas216_info(FAS216_Info *info, char *buffer) { char *p = buffer; p += sprintf(p, "(%s) at port 0x%08lX ", info->scsi.type, info->host->io_port); if (info->host->irq != NO_IRQ) p += sprintf(p, "irq %d ", info->host->irq); else p += sprintf(p, "no irq "); if (info->host->dma_channel != NO_DMA) p += sprintf(p, "dma %d ", info->host->dma_channel); else p += sprintf(p, "no dma "); return p - buffer; } int fas216_print_host(FAS216_Info *info, char *buffer) { return sprintf(buffer, "\n" "Chip : %s\n" " Address: 0x%08lX\n" " IRQ : %d\n" " DMA : %d\n", info->scsi.type, info->host->io_port, info->host->irq, info->host->dma_channel); } int fas216_print_stats(FAS216_Info *info, char *buffer) { return sprintf(buffer, "\n" "Command Statistics:\n" " Queued : %u\n" " Issued : %u\n" " Completed : %u\n" " Reads : %u\n" " Writes : %u\n" " Others : %u\n" " Disconnects: %u\n" " Aborts : %u\n" " Bus resets : %u\n" " Host resets: %u\n", info->stats.queues, info->stats.removes, info->stats.fins, info->stats.reads, info->stats.writes, info->stats.miscs, info->stats.disconnects, info->stats.aborts, info->stats.bus_resets, info->stats.host_resets); } int fas216_print_device(FAS216_Info *info, Scsi_Device *scd, char *buffer) { struct fas216_device *dev = &info->device[scd->id]; int len = 0; char *p; proc_print_scsidevice(scd, buffer, &len, 0); p = buffer + len; p += sprintf(p, " Extensions: "); if (scd->tagged_supported) p += sprintf(p, "TAG %sabled [%d] ", scd->tagged_queue ? "en" : "dis", scd->current_tag); p += sprintf(p, "\n Transfers : %d-bit ", 8 << dev->wide_xfer); if (dev->sof) p += sprintf(p, "sync offset %d, %d ns\n", dev->sof, dev->period * 4); else p += sprintf(p, "async\n"); return p - buffer; } EXPORT_SYMBOL(fas216_info); EXPORT_SYMBOL(fas216_init); EXPORT_SYMBOL(fas216_queue_command); EXPORT_SYMBOL(fas216_command); EXPORT_SYMBOL(fas216_intr); EXPORT_SYMBOL(fas216_release); EXPORT_SYMBOL(fas216_eh_abort); EXPORT_SYMBOL(fas216_eh_device_reset); EXPORT_SYMBOL(fas216_eh_bus_reset); EXPORT_SYMBOL(fas216_eh_host_reset); EXPORT_SYMBOL(fas216_print_host); EXPORT_SYMBOL(fas216_print_stats); EXPORT_SYMBOL(fas216_print_device); #ifdef MODULE int init_module(void) { return 0; } void cleanup_module(void) { } #endif