/* epic100.c: A SMC 83c170 EPIC/100 fast ethernet driver for Linux. */ /* NOTICE: THIS IS THE ALPHA TEST VERSION! Written 1997 by Donald Becker. This software may be used and distributed according to the terms of the GNU Public License, incorporated herein by reference. All other rights reserved. This driver is for the SMC EtherPower II 9432 PCI ethernet adapter based on the SMC83c170. The author may be reached as becker@CESDIS.gsfc.nasa.gov, or C/O Center of Excellence in Space Data and Information Sciences Code 930.5, Goddard Space Flight Center, Greenbelt MD 20771 Support and updates available at http://cesdis.gsfc.nasa.gov/linux/drivers/epic100.html */ static const char *version = "epic100.c:v0.10 10/14/97 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/epic100.html\n"; /* A few user-configurable values. */ /* Keep the ring sizes a power of two for efficiency. Making the Tx ring too large decreases the effectiveness of channel bonding and packet priority. There are no ill effects from too-large receive rings. */ #define TX_RING_SIZE 16 #define RX_RING_SIZE 32 /* Set the copy breakpoint for the copy-only-tiny-frames scheme. Setting to > 1518 effectively disables this feature. */ static const int rx_copybreak = 200; /* Maximum events (Rx packets, etc.) to handle at each interrupt. */ static int max_interrupt_work = 10; /* Operational parameters that usually are not changed. */ /* Time in jiffies before concluding the transmitter is hung. */ #define TX_TIMEOUT ((2000*HZ)/1000) #define PKT_BUF_SZ 1536 /* Size of each temporary Rx buffer.*/ /* Bytes transferred to chip before transmission starts. */ #define TX_FIFO_THRESH 128 /* Rounded down to 4 byte units. */ #define RX_FIFO_THRESH 1 /* 0-3, 0==32, 64,96, or 3==128 bytes */ #include #ifdef MODULE #ifdef MODVERSIONS #include #endif #include #include #else #define MOD_INC_USE_COUNT #define MOD_DEC_USE_COUNT #endif #include #include #include #include #include #include #include #include #include #include #include /* Processor type for cache alignment. */ #include #include #include #include #include #include /* Kernel compatibility defines, common to David Hind's PCMCIA package. This is only in the support-all-kernels source code. */ #include /* Evil, but neccessary */ #if defined (LINUX_VERSION_CODE) && LINUX_VERSION_CODE < 0x10300 #define RUN_AT(x) (x) /* What to put in timer->expires. */ #define DEV_ALLOC_SKB(len) alloc_skb(len, GFP_ATOMIC) #define virt_to_bus(addr) ((unsigned long)addr) #define bus_to_virt(addr) ((void*)addr) #else /* 1.3.0 and later */ #define RUN_AT(x) (jiffies + (x)) #define DEV_ALLOC_SKB(len) dev_alloc_skb(len + 2) #endif #if defined (LINUX_VERSION_CODE) && LINUX_VERSION_CODE < 0x10338 #ifdef MODULE #if !defined(CONFIG_MODVERSIONS) && !defined(__NO_VERSION__) char kernel_version[] = UTS_RELEASE; #endif #else #undef MOD_INC_USE_COUNT #define MOD_INC_USE_COUNT #undef MOD_DEC_USE_COUNT #define MOD_DEC_USE_COUNT #endif #endif /* 1.3.38 */ #if (LINUX_VERSION_CODE >= 0x10344) #define NEW_MULTICAST #include #endif #ifdef SA_SHIRQ #define FREE_IRQ(irqnum, dev) free_irq(irqnum, dev) #define REQUEST_IRQ(i,h,f,n, instance) request_irq(i,h,f,n, instance) #define IRQ(irq, dev_id, pt_regs) (irq, dev_id, pt_regs) #else #define FREE_IRQ(irqnum, dev) free_irq(irqnum) #define REQUEST_IRQ(i,h,f,n, instance) request_irq(i,h,f,n) #define IRQ(irq, dev_id, pt_regs) (irq, pt_regs) #endif #if (LINUX_VERSION_CODE < 0x20123) #define test_and_set_bit(val, addr) set_bit(val, addr) #include #else #ifdef MODULE MODULE_AUTHOR("Donald Becker "); MODULE_DESCRIPTION("SMC 82c170 EPIC series Ethernet driver"); MODULE_PARM(debug, "i"); MODULE_PARM(options, "1-" __MODULE_STRING(8) "i"); MODULE_PARM(full_duplex, "1-" __MODULE_STRING(8) "i"); MODULE_PARM(rx_copybreak, "i"); MODULE_PARM(max_interrupt_work, "i"); #endif #endif /* The I/O extent. */ #define EPIC_TOTAL_SIZE 0x100 #ifdef HAVE_DEVLIST struct netdev_entry epic100_drv = {"Epic100", epic100_pci_probe, EPIC_TOTAL_SIZE, NULL}; #endif static int epic_debug = 1; /* Theory of Operation I. Board Compatibility This device driver is designed for the SMC "EPCI/100", the SMC single-chip ethernet controllers for PCI. This chip is used on the SMC EtherPower II boards. II. Board-specific settings PCI bus devices are configured by the system at boot time, so no jumpers need to be set on the board. The system BIOS will assign the PCI INTA signal to a (preferably otherwise unused) system IRQ line. Note: Kernel versions earlier than 1.3.73 do not support shared PCI interrupt lines. III. Driver operation IIIa. Ring buffers IVb. References http://www.smc.com/components/catalog/smc83c170.html http://cesdis.gsfc.nasa.gov/linux/misc/NWay.html http://www.national.com/pf/DP/DP83840.html IVc. Errata */ #ifndef PCI_VENDOR_ID_SMC #define PCI_VENDOR_ID_SMC 0x10B8 #endif #ifndef PCI_DEVICE_ID_SMC_EPIC100 #define PCI_DEVICE_ID_SMC_EPIC100 0x0005 #endif /* The rest of these values should never change. */ /* Offsets to registers, using the (ugh) SMC names. */ enum epic_registers { COMMAND=0, INTSTAT=4, INTMASK=8, GENCTL=0x0C, NVCTL=0x10, EECTL=0x14, TEST1=0x1C, CRCCNT=0x20, ALICNT=0x24, MPCNT=0x28, /* Rx error counters. */ MIICtrl=0x30, MIIData=0x34, MIICfg=0x38, LAN0=64, /* MAC address. */ MC0=80, /* Multicast filter table. */ RxCtrl=96, TxCtrl=112, TxSTAT=0x74, PRxCDAR=0x84, RxSTAT=0xA4, EarlyRx=0xB0, PTxCDAR=0xC4, TxThresh=0xDC, }; /* Interrupt register bits, using my own meaningful names. */ enum IntrStatus { TxIdle=0x40000, RxIdle=0x20000, CntFull=0x0200, TxUnderrun=0x0100, TxEmpty=0x0080, TxDone=0x0020, RxError=0x0010, RxOverflow=0x0008, RxFull=0x0004, RxHeader=0x0002, RxDone=0x0001, }; /* The EPIC100 Rx and Tx buffer descriptors. */ struct epic_tx_desc { s16 status; u16 txlength; u32 bufaddr; u16 buflength; u16 control; u32 next; }; struct epic_rx_desc { s16 status; u16 rxlength; u32 bufaddr; u32 buflength; u32 next; }; struct epic_private { char devname[8]; /* Used only for kernel debugging. */ const char *product_name; struct device *next_module; struct epic_rx_desc rx_ring[RX_RING_SIZE]; struct epic_tx_desc tx_ring[TX_RING_SIZE]; /* The saved address of a sent-in-place packet/buffer, for skfree(). */ struct sk_buff* tx_skbuff[TX_RING_SIZE]; /* The addresses of receive-in-place skbuffs. */ struct sk_buff* rx_skbuff[RX_RING_SIZE]; int chip_id; int revision; struct enet_statistics stats; struct timer_list timer; /* Media selection timer. */ unsigned int cur_rx, cur_tx; /* The next free ring entry */ unsigned int dirty_rx, dirty_tx; /* The ring entries to be free()ed. */ unsigned char mc_filter[8]; signed char phys[4]; /* MII device addresses. */ unsigned int tx_full:1; /* The Tx queue is full. */ unsigned int full_duplex:1; /* Full-duplex operation requested. */ unsigned int default_port:4; /* Last dev->if_port value. */ unsigned int media2:4; /* Secondary monitored media port. */ unsigned int medialock:1; /* Don't sense media type. */ unsigned int mediasense:1; /* Media sensing in progress. */ int pad0, pad1; /* Used for 8-byte alignment */ }; static int full_duplex[] = {-1, -1, -1, -1, -1, -1, -1, -1}; #ifdef MODULE /* Used to pass the full-duplex flag, etc. */ static int options[] = {-1, -1, -1, -1, -1, -1, -1, -1}; #endif static struct device *epic100_probe1(struct device *dev, int ioaddr, int irq, int chip_id, int options, int card_idx); static int epic_open(struct device *dev); static int read_eeprom(int ioaddr, int location); static int mii_read(int ioaddr, int phy_id, int location); static void epic_timer(unsigned long data); static void epic_tx_timeout(struct device *dev); static void epic_init_ring(struct device *dev); static int epic_start_xmit(struct sk_buff *skb, struct device *dev); static int epic_rx(struct device *dev); static void epic_interrupt(int irq, void *dev_instance, struct pt_regs *regs); static int epic_close(struct device *dev); static struct enet_statistics *epic_get_stats(struct device *dev); #ifdef NEW_MULTICAST static void set_rx_mode(struct device *dev); #else static void set_rx_mode(struct device *dev, int num_addrs, void *addrs); #endif #ifdef MODULE /* A list of all installed EPIC devices, for removing the driver module. */ static struct device *root_epic_dev = NULL; #endif int epic100_probe(struct device *dev) { int cards_found = 0; static int pci_index = 0; /* Static, for multiple probe calls. */ /* Ideally we would detect all network cards in slot order. That would be best done a central PCI probe dispatch, which wouldn't work well with the current structure. So instead we detect just the Epic cards in slot order. */ if (pci_present()) { unsigned char pci_bus, pci_device_fn; for (;pci_index < 0xff; pci_index++) { #if LINUX_VERSION_CODE >= 0x20155 unsigned int pci_irq_line; struct pci_dev *pdev; #else unsigned char pci_irq_line; #endif unsigned char pci_latency; unsigned short pci_command, vendor, device; unsigned int pci_ioaddr, chip_idx = 0; if (pcibios_find_class (PCI_CLASS_NETWORK_ETHERNET << 8, #ifdef REVERSE_PROBE_ORDER 0xff - pci_index, #else pci_index, #endif &pci_bus, &pci_device_fn) != PCIBIOS_SUCCESSFUL) break; pcibios_read_config_word(pci_bus, pci_device_fn, PCI_VENDOR_ID, &vendor); if (vendor != PCI_VENDOR_ID_SMC) continue; pcibios_read_config_word(pci_bus, pci_device_fn, PCI_DEVICE_ID, &device); #if LINUX_VERSION_CODE >= 0x20155 pdev = pci_find_slot(pci_bus, pci_device_fn); pci_irq_line = pdev->irq; pci_ioaddr = pdev->base_address[0]; #else pcibios_read_config_byte(pci_bus, pci_device_fn, PCI_INTERRUPT_LINE, &pci_irq_line); pcibios_read_config_dword(pci_bus, pci_device_fn, PCI_BASE_ADDRESS_0, &pci_ioaddr); #endif /* Remove I/O space marker in bit 0. */ pci_ioaddr &= ~3; if (device != PCI_DEVICE_ID_SMC_EPIC100) { printk("Unknown SMC PCI ethernet chip type %4.4x detected:" " not configured.\n", device); continue; } if (epic_debug > 2) printk("Found SMC PCI EPIC/100 at I/O %#x, IRQ %d.\n", pci_ioaddr, pci_irq_line); if (check_region(pci_ioaddr, EPIC_TOTAL_SIZE)) continue; #ifdef MODULE dev = epic100_probe1(dev, pci_ioaddr, pci_irq_line, chip_idx, options[cards_found], cards_found); #else dev = epic100_probe1(dev, pci_ioaddr, pci_irq_line, chip_idx, dev ? dev->mem_start : 0, -1); #endif if (dev) { /* Get and check the bus-master and latency values. */ pcibios_read_config_word(pci_bus, pci_device_fn, PCI_COMMAND, &pci_command); if ( ! (pci_command & PCI_COMMAND_MASTER)) { printk(" PCI Master Bit has not been set! Setting...\n"); pci_command |= PCI_COMMAND_MASTER; pcibios_write_config_word(pci_bus, pci_device_fn, PCI_COMMAND, pci_command); } pcibios_read_config_byte(pci_bus, pci_device_fn, PCI_LATENCY_TIMER, &pci_latency); if (pci_latency < 10) { printk(" PCI latency timer (CFLT) is unreasonably low at %d." " Setting to 255 clocks.\n", pci_latency); pcibios_write_config_byte(pci_bus, pci_device_fn, PCI_LATENCY_TIMER, 255); } else if (epic_debug > 1) printk(" PCI latency timer (CFLT) is %#x.\n", pci_latency); dev = 0; cards_found++; } } } #if defined (MODULE) return cards_found; #else return cards_found ? 0 : -ENODEV; #endif } static struct device *epic100_probe1(struct device *dev, int ioaddr, int irq, int chip_id, int options, int card_idx) { static int did_version = 0; /* Already printed version info. */ struct epic_private *tp; int i; if (epic_debug > 0 && did_version++ == 0) printk(version); dev = init_etherdev(dev, 0); printk("%s: SMC EPIC/100 at %#3x, IRQ %d, ", dev->name, ioaddr, irq); /* Bring the chip out of low-power mode. */ outl(0x0200, ioaddr + GENCTL); /* Magic?! If we don't set this bit the MII interface won't work. */ outl(0x0008, ioaddr + TEST1); /* This could also be read from the EEPROM. */ for (i = 0; i < 3; i++) ((u16 *)dev->dev_addr)[i] = inw(ioaddr + LAN0 + i*4); for (i = 0; i < 5; i++) printk("%2.2x:", dev->dev_addr[i]); printk("%2.2x.\n", dev->dev_addr[i]); if (epic_debug > 1) { printk("%s: EEPROM contents\n", dev->name); for (i = 0; i < 64; i++) printk(" %4.4x%s", read_eeprom(ioaddr, i), i % 16 == 15 ? "\n" : ""); } /* We do a request_region() to register /proc/ioports info. */ request_region(ioaddr, EPIC_TOTAL_SIZE, "SMC EPIC/100"); dev->base_addr = ioaddr; dev->irq = irq; /* The data structures must be quadword aligned. */ tp = kmalloc(sizeof(*tp), GFP_KERNEL | GFP_DMA); memset(tp, 0, sizeof(*tp)); dev->priv = tp; #ifdef MODULE tp->next_module = root_epic_dev; root_epic_dev = dev; #endif tp->chip_id = chip_id; /* Find the connected MII xcvrs. Doing this in open() would allow detecting external xcvrs later, but takes too much time. */ { int phy, phy_idx; for (phy = 0, phy_idx = 0; phy < 32 && phy_idx < sizeof(tp->phys); phy++) { int mii_status = mii_read(ioaddr, phy, 0); if (mii_status != 0xffff && mii_status != 0x0000) { tp->phys[phy_idx++] = phy; printk("%s: MII transceiver found at address %d.\n", dev->name, phy); } } if (phy_idx == 0) { printk("%s: ***WARNING***: No MII transceiver found!\n", dev->name); /* Use the known PHY address of the EPII. */ tp->phys[0] = 3; } } /* Leave the chip in low-power mode. */ outl(0x0008, ioaddr + GENCTL); /* The lower four bits are the media type. */ if (options > 0) { tp->full_duplex = (options & 16) ? 1 : 0; tp->default_port = options & 15; if (tp->default_port) tp->medialock = 1; } if (card_idx >= 0) { if (full_duplex[card_idx] >= 0) tp->full_duplex = full_duplex[card_idx]; } /* The Epic-specific entries in the device structure. */ dev->open = &epic_open; dev->hard_start_xmit = &epic_start_xmit; dev->stop = &epic_close; dev->get_stats = &epic_get_stats; dev->set_multicast_list = &set_rx_mode; return dev; } /* Serial EEPROM section. */ /* EEPROM_Ctrl bits. */ #define EE_SHIFT_CLK 0x04 /* EEPROM shift clock. */ #define EE_CS 0x02 /* EEPROM chip select. */ #define EE_DATA_WRITE 0x08 /* EEPROM chip data in. */ #define EE_WRITE_0 0x01 #define EE_WRITE_1 0x09 #define EE_DATA_READ 0x10 /* EEPROM chip data out. */ #define EE_ENB (0x0001 | EE_CS) /* Delay between EEPROM clock transitions. The 1.2 code is a "nasty" timing loop, but PC compatible machines are *supposed* to delay an ISA-compatible period for the SLOW_DOWN_IO macro. */ #ifdef _LINUX_DELAY_H #define eeprom_delay(nanosec) udelay((nanosec + 999)/1000) #else #define eeprom_delay(nanosec) do { int _i = 3; while (--_i > 0) { __SLOW_DOWN_IO; }} while (0) #endif /* The EEPROM commands include the alway-set leading bit. */ #define EE_WRITE_CMD (5 << 6) #define EE_READ_CMD (6 << 6) #define EE_ERASE_CMD (7 << 6) static int read_eeprom(int ioaddr, int location) { int i; int retval = 0; int ee_addr = ioaddr + EECTL; int read_cmd = location | EE_READ_CMD; outl(EE_ENB & ~EE_CS, ee_addr); outl(EE_ENB, ee_addr); /* Shift the read command bits out. */ for (i = 10; i >= 0; i--) { short dataval = (read_cmd & (1 << i)) ? EE_DATA_WRITE : 0; outl(EE_ENB | dataval, ee_addr); eeprom_delay(100); outl(EE_ENB | dataval | EE_SHIFT_CLK, ee_addr); eeprom_delay(150); outl(EE_ENB | dataval, ee_addr); /* Finish EEPROM a clock tick. */ eeprom_delay(250); } outl(EE_ENB, ee_addr); for (i = 16; i > 0; i--) { outl(EE_ENB | EE_SHIFT_CLK, ee_addr); eeprom_delay(100); retval = (retval << 1) | ((inl(ee_addr) & EE_DATA_READ) ? 1 : 0); outl(EE_ENB, ee_addr); eeprom_delay(100); } /* Terminate the EEPROM access. */ outl(EE_ENB & ~EE_CS, ee_addr); return retval; } #define MII_READOP 1 #define MII_WRITEOP 2 static int mii_read(int ioaddr, int phy_id, int location) { int i; outl((phy_id << 9) | (location << 4) | MII_READOP, ioaddr + MIICtrl); /* Typical operation takes < 50 ticks. */ for (i = 4000; i > 0; i--) if ((inl(ioaddr + MIICtrl) & MII_READOP) == 0) break; return inw(ioaddr + MIIData); } static int epic_open(struct device *dev) { struct epic_private *tp = (struct epic_private *)dev->priv; int ioaddr = dev->base_addr; int i; int mii_reg5; int full_duplex = 0; /* Soft reset the chip. */ outl(0x0001, ioaddr + GENCTL); #ifdef SA_SHIRQ if (request_irq(dev->irq, &epic_interrupt, SA_SHIRQ, "SMC EPIC/100", dev)) { return -EAGAIN; } #else if (irq2dev_map[dev->irq] != NULL || (irq2dev_map[dev->irq] = dev) == NULL || dev->irq == 0 || request_irq(dev->irq, &epic_interrupt, 0, "SMC EPIC/100")) { return -EAGAIN; } #endif MOD_INC_USE_COUNT; epic_init_ring(dev); /* This next line by Ken Yamaguchi.. ?? */ outl(0x8, ioaddr + 0x1c); /* Pull the chip out of low-power mode, enable interrupts, and set for PCI read multiple. */ outl(0x0412 | (RX_FIFO_THRESH<<8), ioaddr + GENCTL); for (i = 0; i < 3; i++) outl(((u16*)dev->dev_addr)[i], ioaddr + LAN0 + i*4); outl(TX_FIFO_THRESH, ioaddr + TxThresh); full_duplex = tp->full_duplex; mii_reg5 = mii_read(ioaddr, tp->phys[0], 5); if (mii_reg5 != 0xffff && (mii_reg5 & 0x0100)) { full_duplex = 1; if (epic_debug > 1) printk("%s: Setting %s-duplex based on MII xcvr %d" " register read of %4.4x.\n", dev->name, full_duplex ? "full" : "half", tp->phys[0], mii_read(ioaddr, tp->phys[0], 5)); } outl(full_duplex ? 0x7F : 0x79, ioaddr + TxCtrl); outl(virt_to_bus(tp->rx_ring), ioaddr + PRxCDAR); outl(virt_to_bus(tp->tx_ring), ioaddr + PTxCDAR); /* Start the chip's Rx process. */ set_rx_mode(dev); outl(0x000A, ioaddr + COMMAND); dev->tbusy = 0; dev->interrupt = 0; dev->start = 1; /* Enable interrupts by setting the interrupt mask. */ outl(CntFull | TxUnderrun | TxDone | RxError | RxOverflow | RxFull | RxHeader | RxDone, ioaddr + INTMASK); if (epic_debug > 1) printk("%s: epic_open() ioaddr %4.4x IRQ %d status %4.4x %s-duplex.\n", dev->name, ioaddr, dev->irq, inl(ioaddr + GENCTL), full_duplex ? "full" : "half"); /* Set the timer to switch to check for link beat and perhaps switch to an alternate media type. */ init_timer(&tp->timer); tp->timer.expires = RUN_AT((24*HZ)/10); /* 2.4 sec. */ tp->timer.data = (unsigned long)dev; tp->timer.function = &epic_timer; /* timer handler */ add_timer(&tp->timer); return 0; } static void epic_timer(unsigned long data) { struct device *dev = (struct device *)data; struct epic_private *tp = (struct epic_private *)dev->priv; int ioaddr = dev->base_addr; int next_tick = 0; if (epic_debug > 3) { printk("%s: Media selection tick, Tx status %8.8x.\n", dev->name, inl(ioaddr + TxSTAT)); printk("%s: Other registers are IntMask %4.4x IntStatus %4.4x RxStatus" " %4.4x.\n", dev->name, inl(ioaddr + INTMASK), inl(ioaddr + INTSTAT), inl(ioaddr + RxSTAT)); } if (next_tick) { tp->timer.expires = RUN_AT(next_tick); add_timer(&tp->timer); } } static void epic_tx_timeout(struct device *dev) { struct epic_private *tp = (struct epic_private *)dev->priv; int ioaddr = dev->base_addr; if (epic_debug > 0) { printk("%s: Transmit timeout using MII device, Tx status %4.4x.\n", dev->name, inw(ioaddr + TxSTAT)); if (epic_debug > 1) { printk("%s: Tx indices: dirty_tx %d, cur_tx %d.\n", dev->name, tp->dirty_tx, tp->cur_tx); } } /* Perhaps stop and restart the chip's Tx processes . */ /* Trigger a transmit demand. */ outl(0x0004, dev->base_addr + COMMAND); dev->trans_start = jiffies; tp->stats.tx_errors++; return; } /* Initialize the Rx and Tx rings, along with various 'dev' bits. */ static void epic_init_ring(struct device *dev) { struct epic_private *tp = (struct epic_private *)dev->priv; int i; tp->tx_full = 0; tp->cur_rx = tp->cur_tx = 0; tp->dirty_rx = tp->dirty_tx = 0; for (i = 0; i < RX_RING_SIZE; i++) { tp->rx_ring[i].status = 0x8000; /* Owned by Epic chip */ tp->rx_ring[i].buflength = PKT_BUF_SZ; { /* Note the receive buffer must be longword aligned. dev_alloc_skb() provides 16 byte alignment. But do *not* use skb_reserve() to align the IP header! */ struct sk_buff *skb; skb = DEV_ALLOC_SKB(PKT_BUF_SZ); tp->rx_skbuff[i] = skb; if (skb == NULL) break; /* Bad news! */ skb->dev = dev; /* Mark as being used by this device. */ #if LINUX_VERSION_CODE > 0x10300 skb_reserve(skb, 2); /* Align IP on 16 byte boundaries */ tp->rx_ring[i].bufaddr = virt_to_bus(skb->tail); #else tp->rx_ring[i].bufaddr = virt_to_bus(skb->data); #endif } tp->rx_ring[i].next = virt_to_bus(&tp->rx_ring[i+1]); } /* Mark the last entry as wrapping the ring. */ tp->rx_ring[i-1].next = virt_to_bus(&tp->rx_ring[0]); /* The Tx buffer descriptor is filled in as needed, but we do need to clear the ownership bit. */ for (i = 0; i < TX_RING_SIZE; i++) { tp->tx_skbuff[i] = 0; tp->tx_ring[i].status = 0x0000; tp->tx_ring[i].next = virt_to_bus(&tp->tx_ring[i+1]); } tp->tx_ring[i-1].next = virt_to_bus(&tp->tx_ring[0]); } static int epic_start_xmit(struct sk_buff *skb, struct device *dev) { struct epic_private *tp = (struct epic_private *)dev->priv; int entry; u32 flag; #ifndef final_version if (skb == NULL || skb->len <= 0) { printk("%s: Obsolete driver layer request made: skbuff==NULL.\n", dev->name); #if 0 dev_tint(dev); #endif return 0; } #endif /* Block a timer-based transmit from overlapping. This could better be done with atomic_swap(1, dev->tbusy), but set_bit() works as well. */ if (test_and_set_bit(0, (void*)&dev->tbusy) != 0) { if (jiffies - dev->trans_start < TX_TIMEOUT) return 1; epic_tx_timeout(dev); return 1; } /* Caution: the write order is important here, set the base address with the "ownership" bits last. */ /* Calculate the next Tx descriptor entry. */ entry = tp->cur_tx % TX_RING_SIZE; tp->tx_skbuff[entry] = skb; tp->tx_ring[entry].txlength = (skb->len >= ETH_ZLEN ? skb->len : ETH_ZLEN); tp->tx_ring[entry].bufaddr = virt_to_bus(skb->data); tp->tx_ring[entry].buflength = skb->len; if (tp->cur_tx - tp->dirty_tx < TX_RING_SIZE/2) {/* Typical path */ flag = 0x10; /* No interrupt */ dev->tbusy = 0; } else if (tp->cur_tx - tp->dirty_tx == TX_RING_SIZE/2) { flag = 0x14; /* Tx-done intr. */ dev->tbusy = 0; } else if (tp->cur_tx - tp->dirty_tx < TX_RING_SIZE - 2) { flag = 0x10; /* No Tx-done intr. */ dev->tbusy = 0; } else { /* Leave room for two additional entries. */ flag = 0x14; /* Tx-done intr. */ tp->tx_full = 1; } tp->tx_ring[entry].control = flag; tp->tx_ring[entry].status = 0x8000; /* Pass ownership to the chip. */ tp->cur_tx++; /* Trigger an immediate transmit demand. */ outl(0x0004, dev->base_addr + COMMAND); dev->trans_start = jiffies; if (epic_debug > 4) printk("%s: Queued Tx packet size %d to slot %d, " "flag %2.2x Tx status %8.8x.\n", dev->name, (int)skb->len, entry, flag, inl(dev->base_addr + TxSTAT)); return 0; } /* The interrupt handler does all of the Rx thread work and cleans up after the Tx thread. */ static void epic_interrupt IRQ(int irq, void *dev_instance, struct pt_regs *regs) { #ifdef SA_SHIRQ struct device *dev = (struct device *)dev_instance; #else struct device *dev = (struct device *)(irq2dev_map[irq]); #endif struct epic_private *lp; int status, ioaddr, boguscnt = max_interrupt_work; if (dev == NULL) { printk ("epic_interrupt(): irq %d for unknown device.\n", irq); return; } ioaddr = dev->base_addr; lp = (struct epic_private *)dev->priv; if (dev->interrupt) printk("%s: Re-entering the interrupt handler.\n", dev->name); dev->interrupt = 1; do { status = inl(ioaddr + INTSTAT); /* Acknowledge all of the current interrupt sources ASAP. */ outl(status & 0x00007fff, ioaddr + INTSTAT); if (epic_debug > 4) printk("%s: interrupt interrupt=%#8.8x new intstat=%#8.8x.\n", dev->name, status, inl(ioaddr + INTSTAT)); if ((status & (RxDone | TxEmpty | TxDone)) == 0) break; if (status & RxDone) /* Rx interrupt */ epic_rx(dev); if (status & (TxEmpty | TxDone)) { int dirty_tx; for (dirty_tx = lp->dirty_tx; dirty_tx < lp->cur_tx; dirty_tx++) { int entry = dirty_tx % TX_RING_SIZE; int txstatus = lp->tx_ring[entry].status; if (txstatus < 0) break; /* It still hasn't been Txed */ if ( ! (txstatus & 0x0001)) { /* There was an major error, log it. */ #ifndef final_version if (epic_debug > 1) printk("%s: Transmit error, Tx status %8.8x.\n", dev->name, txstatus); #endif lp->stats.tx_errors++; if (txstatus & 0x1050) lp->stats.tx_aborted_errors++; if (txstatus & 0x0008) lp->stats.tx_carrier_errors++; if (txstatus & 0x0040) lp->stats.tx_window_errors++; if (txstatus & 0x0010) lp->stats.tx_fifo_errors++; #ifdef ETHER_STATS if (txstatus & 0x1000) lp->stats.collisions16++; #endif } else { #ifdef ETHER_STATS if ((txstatus & 0x0002) != 0) lp->stats.tx_deferred++; #endif lp->stats.collisions += (txstatus >> 8) & 15; lp->stats.tx_packets++; } /* Free the original skb. */ dev_kfree_skb(lp->tx_skbuff[entry]); lp->tx_skbuff[entry] = 0; } #ifndef final_version if (lp->cur_tx - dirty_tx > TX_RING_SIZE) { printk("%s: Out-of-sync dirty pointer, %d vs. %d, full=%d.\n", dev->name, dirty_tx, lp->cur_tx, lp->tx_full); dirty_tx += TX_RING_SIZE; } #endif if (lp->tx_full && dev->tbusy && dirty_tx > lp->cur_tx - TX_RING_SIZE + 2) { /* The ring is no longer full, clear tbusy. */ lp->tx_full = 0; dev->tbusy = 0; mark_bh(NET_BH); } lp->dirty_tx = dirty_tx; } /* Check uncommon events all at once. */ if (status & (CntFull | TxUnderrun | RxOverflow)) { /* Always update the error counts to avoid overhead later. */ lp->stats.rx_missed_errors += inb(ioaddr + MPCNT); lp->stats.rx_frame_errors += inb(ioaddr + ALICNT); lp->stats.rx_crc_errors += inb(ioaddr + CRCCNT); if (status & TxUnderrun) { /* Tx FIFO underflow. */ lp->stats.tx_fifo_errors++; /* Restart the transmit process. */ outl(0x0080, ioaddr + COMMAND); } if (status & RxOverflow) { /* Missed a Rx frame. */ lp->stats.rx_errors++; } /* Clear all error sources. */ outl(status & 0x7f18, ioaddr + INTSTAT); } if (--boguscnt < 0) { printk("%s: Too much work at interrupt, IntrStatus=0x%8.8x.\n", dev->name, status); /* Clear all interrupt sources. */ outl(0x0001ffff, ioaddr + INTSTAT); break; } } while (1); if (epic_debug > 3) printk("%s: exiting interrupt, intr_status=%#4.4x.\n", dev->name, inl(ioaddr + INTSTAT)); /* Code that should never be run! Perhaps remove after testing.. */ { static int stopit = 10; if (dev->start == 0 && --stopit < 0) { printk("%s: Emergency stop, looping startup interrupt.\n", dev->name); FREE_IRQ(irq, dev); } } dev->interrupt = 0; return; } static int epic_rx(struct device *dev) { struct epic_private *lp = (struct epic_private *)dev->priv; int entry = lp->cur_rx % RX_RING_SIZE; if (epic_debug > 4) printk(" In epic_rx(), entry %d %8.8x.\n", entry, lp->rx_ring[entry].status); /* If we own the next entry, it's a new packet. Send it up. */ while (lp->rx_ring[entry].status >= 0) { int status = lp->rx_ring[entry].status; if (epic_debug > 4) printk(" epic_rx() status was %8.8x.\n", status); if (status & 0x2000) { printk("%s: Oversized Ethernet frame spanned multiple buffers," " status %4.4x!\n", dev->name, status); lp->stats.rx_length_errors++; } else if (status & 0x0006) { /* Rx Frame errors are counted in hardware. */ lp->stats.rx_errors++; } else { /* Malloc up new buffer, compatible with net-2e. */ /* Omit the four octet CRC from the length. */ short pkt_len = lp->rx_ring[entry].rxlength - 4; struct sk_buff *skb; int rx_in_place = 0; /* Check if the packet is long enough to just accept without copying to a properly sized skbuff. */ if (pkt_len > rx_copybreak) { struct sk_buff *newskb; char *temp; /* Pass up the skb already on the Rx ring. */ skb = lp->rx_skbuff[entry]; temp = skb_put(skb, pkt_len); if (bus_to_virt(lp->rx_ring[entry].bufaddr) != temp) printk("%s: Warning -- the skbuff addresses do not match" " in epic_rx: %p vs. %p / %p.\n", dev->name, bus_to_virt(lp->rx_ring[entry].bufaddr), skb->head, temp); /* Get a fresh skbuff to replace the filled one. */ newskb = DEV_ALLOC_SKB(PKT_BUF_SZ); if (newskb) { rx_in_place = 1; lp->rx_skbuff[entry] = newskb; newskb->dev = dev; #if LINUX_VERSION_CODE > 0x10300 /* Align IP on 16 byte boundaries */ skb_reserve(newskb, 2); lp->rx_ring[entry].bufaddr = virt_to_bus(newskb->tail); #else lp->rx_ring[entry].bufaddr = virt_to_bus(newskb->data); #endif } else /* No memory, drop the packet. */ skb = 0; } else skb = DEV_ALLOC_SKB(pkt_len + 2); if (skb == NULL) { int i; printk("%s: Memory squeeze, deferring packet.\n", dev->name); /* Check that at least two ring entries are free. If not, free one and mark stats->rx_dropped++. */ for (i = 0; i < RX_RING_SIZE; i++) if (lp->rx_ring[(entry+i) % RX_RING_SIZE].status < 0) break; if (i > RX_RING_SIZE -2) { lp->stats.rx_dropped++; lp->rx_ring[entry].status = 0x8000; lp->cur_rx++; } break; } skb->dev = dev; if (! rx_in_place) { skb_reserve(skb, 2); /* 16 byte align the data fields */ memcpy(skb_put(skb, pkt_len), bus_to_virt(lp->rx_ring[entry].bufaddr), pkt_len); } #if LINUX_VERSION_CODE > 0x10300 skb->protocol = eth_type_trans(skb, dev); #else skb->len = pkt_len; #endif netif_rx(skb); lp->stats.rx_packets++; } lp->rx_ring[entry].status = 0x8000; entry = (++lp->cur_rx) % RX_RING_SIZE; } return 0; } static int epic_close(struct device *dev) { int ioaddr = dev->base_addr; struct epic_private *tp = (struct epic_private *)dev->priv; int i; dev->start = 0; dev->tbusy = 1; if (epic_debug > 1) printk("%s: Shutting down ethercard, status was %2.2x.\n", dev->name, inl(ioaddr + INTSTAT)); /* Disable interrupts by clearing the interrupt mask. */ outl(0x00000000, ioaddr + INTMASK); /* Stop the chip's Tx and Rx DMA processes. */ outw(0x0061, ioaddr + COMMAND); /* Update the error counts. */ tp->stats.rx_missed_errors += inb(ioaddr + MPCNT); tp->stats.rx_frame_errors += inb(ioaddr + ALICNT); tp->stats.rx_crc_errors += inb(ioaddr + CRCCNT); del_timer(&tp->timer); #ifdef SA_SHIRQ free_irq(dev->irq, dev); #else free_irq(dev->irq); irq2dev_map[dev->irq] = 0; #endif /* Free all the skbuffs in the Rx queue. */ for (i = 0; i < RX_RING_SIZE; i++) { struct sk_buff *skb = tp->rx_skbuff[i]; tp->rx_skbuff[i] = 0; tp->rx_ring[i].status = 0; /* Not owned by Epic chip. */ tp->rx_ring[i].buflength = 0; tp->rx_ring[i].bufaddr = 0xBADF00D0; /* An invalid address. */ if (skb) { #if LINUX_VERSION_CODE < 0x20100 skb->free = 1; #endif dev_kfree_skb(skb); } } for (i = 0; i < TX_RING_SIZE; i++) { if (tp->tx_skbuff[i]) dev_kfree_skb(tp->tx_skbuff[i]); tp->tx_skbuff[i] = 0; } /* Green! Leave the chip in low-power mode. */ outl(0x0008, ioaddr + GENCTL); MOD_DEC_USE_COUNT; return 0; } static struct enet_statistics * epic_get_stats(struct device *dev) { struct epic_private *tp = (struct epic_private *)dev->priv; int ioaddr = dev->base_addr; if (dev->start) { /* Update the error counts. */ tp->stats.rx_missed_errors += inb(ioaddr + MPCNT); tp->stats.rx_frame_errors += inb(ioaddr + ALICNT); tp->stats.rx_crc_errors += inb(ioaddr + CRCCNT); } return &tp->stats; } /* Set or clear the multicast filter for this adaptor. Note that we only use exclusion around actually queueing the new frame, not around filling tp->setup_frame. This is non-deterministic when re-entered but still correct. */ /* The little-endian AUTODIN II ethernet CRC calculation. N.B. Do not use for bulk data, use a table-based routine instead. This is common code and should be moved to net/core/crc.c */ static unsigned const ethernet_polynomial_le = 0xedb88320U; static inline unsigned ether_crc_le(int length, unsigned char *data) { unsigned int crc = 0xffffffff; /* Initial value. */ while(--length >= 0) { unsigned char current_octet = *data++; int bit; for (bit = 8; --bit >= 0; current_octet >>= 1) { if ((crc ^ current_octet) & 1) { crc >>= 1; crc ^= ethernet_polynomial_le; } else crc >>= 1; } } return crc; } #ifdef NEW_MULTICAST static void set_rx_mode(struct device *dev) #else static void set_rx_mode(struct device *dev, int num_addrs, void *addrs); #endif { int ioaddr = dev->base_addr; struct epic_private *tp = (struct epic_private *)dev->priv; unsigned char mc_filter[8]; /* Multicast hash filter */ int i; if (dev->flags & IFF_PROMISC) { /* Set promiscuous. */ outl(0x002C, ioaddr + RxCtrl); /* Unconditionally log net taps. */ printk("%s: Promiscuous mode enabled.\n", dev->name); memset(mc_filter, 0xff, sizeof(mc_filter)); } else if ((dev->mc_count > 0) || (dev->flags & IFF_ALLMULTI)) { /* There is apparently a chip bug, so the multicast filter is never enabled. */ /* Too many to filter perfectly -- accept all multicasts. */ memset(mc_filter, 0xff, sizeof(mc_filter)); outl(0x000C, ioaddr + RxCtrl); } else if (dev->mc_count == 0) { outl(0x0004, ioaddr + RxCtrl); return; } else { /* Never executed, for now. */ struct dev_mc_list *mclist; memset(mc_filter, 0, sizeof(mc_filter)); for (i = 0, mclist = dev->mc_list; mclist && i < dev->mc_count; i++, mclist = mclist->next) set_bit(ether_crc_le(ETH_ALEN, mclist->dmi_addr) & 0x3f, mc_filter); } /* ToDo: perhaps we need to stop the Tx and Rx process here? */ if (memcmp(mc_filter, tp->mc_filter, sizeof(mc_filter))) { for (i = 0; i < 4; i++) outw(((u16 *)mc_filter)[i], ioaddr + MC0 + i*4); memcpy(tp->mc_filter, mc_filter, sizeof(mc_filter)); } return; } #ifdef MODULE /* An additional parameter that may be passed in... */ static int debug = -1; int init_module(void) { int cards_found; if (debug >= 0) epic_debug = debug; root_epic_dev = NULL; cards_found = epic100_probe(0); return cards_found ? 0 : -ENODEV; } void cleanup_module(void) { struct device *next_dev; /* No need to check MOD_IN_USE, as sys_delete_module() checks. */ while (root_epic_dev) { next_dev = ((struct epic_private *)root_epic_dev->priv)->next_module; unregister_netdev(root_epic_dev); release_region(root_epic_dev->base_addr, EPIC_TOTAL_SIZE); kfree(root_epic_dev); root_epic_dev = next_dev; } } #endif /* MODULE */ /* * Local variables: * compile-command: "gcc -DMODULE -DMODVERSIONS -D__KERNEL__ -Wall -Wstrict-prototypes -O6 -c epic100.c" * c-indent-level: 4 * c-basic-offset: 4 * tab-width: 4 * End: */