#ifndef _NET_H_SYMBA #define _NET_H_SYMBA /* transmit status bit definitions */ #define TX_STATUS_TXOK (1<<13) /* success */ #define TX_STATUS_TDLC (1<<12) /* dropped for late colls */ #define TX_STATUS_TCXSDFR (1<<11) /* excessive deferral */ #define TX_STATUS_TDEC (1<<10) /* excessive collisions */ #define TX_STATUS_TAUR (1<<9) /* abort on underrun/"jumbo" */ #define TX_STATUS_PDFRD (1<<8) /* packet deferred */ #define TX_STATUS_BCAST (1<<7) /* broadcast ok */ #define TX_STATUS_MCAST (1<<6) /* multicast ok */ #define TX_STATUS_CRCERR (1<<5) /* CRC error */ #define TX_STATUS_LC (1<<4) /* late collision */ #define TX_STATUS_CCNT_MASK 0xf /* collision count */ #define T_TXOK (1<<13) #define T_TDLC (1<<12) #define T_TCXSDFR (1<<11) #define T_TDEC (1<<10) #define T_TAUR (1<<9) #define T_PDFRD (1<<8) #define T_BCAST (1<<7) #define T_MCAST (1<<6) #define T_LC (1<<4) #define T_CCNT_MASK 0xf /* receive status bit definitions */ #define RX_STATUS_RXOVRN (1<<23) /* overrun */ #define RX_STATUS_CEPS (1<<22) /* carrier event already seen */ #define RX_STATUS_RXOK (1<<21) /* success */ #define RX_STATUS_BCAST (1<<20) /* broadcast ok */ #define RX_STATUS_MCAST (1<<19) /* multicast ok */ #define RX_STATUS_CRCERR (1<<18) /* CRC error */ #define RX_STATUS_DR (1<<17) /* dribble nibble */ #define RX_STATUS_RCV (1<<16) /* rx code violation */ #define RX_STATUS_PTL (1<<15) /* pkt > 1518 bytes */ #define RX_STATUS_PTS (1<<14) /* pkt < 64 bytes */ #define RX_STATUS_LEN_MASK 0x1fff /* length mask */ #define EEPROM_LENGTH 100 /* Serial EEPROM interface */ #define EE_STATUS 0xf0 #define EE_CONTROL 0xf1 #define EE_WORD_ADDR 0xf2 #define EE_READ_DATA 0xf3 #define EE_WRITE_DATA 0xf4 #define EE_FEATURE_ENB 0xf5 /* Use on EE_STATUS */ #define EE_SEB (1<<8) #define EE_SEE 1 /* Serial EEPROM commands */ #define EE_CONTROL_SEQ_READB (1<<4) #define EE_CONTROL_RND_WRITEB (1<<5) #define EE_CONTROL_RND_READB ((1<<4)|(1<<5)) /* Enable writing to serial EEPROM */ #define EE_WRITE_ENB 1 /* The 885 configuration register */ #define MAC_CONFIG 0xa0 #define MAC_CONFIG_SRST 1<<15 #define MAC_CONFIG_ITXA 1<<13 #define MAC_CONFIG_RXEN 1<<12 #define MAC_CONFIG_INTLB 1<<10 #define MAC_CONFIG_MODE_MASK (1<<8|1<<9) #define MAC_CONFIG_MODE_TP 1<<8 #define MAC_CONFIG_HUGEN 1<<5 #define MAC_CONFIG_RETRYL 1<<4 #define MAC_CONFIG_CRCEN 1<<3 #define MAC_CONFIG_PADEN 1<<2 #define MAC_CONFIG_FULLD 1<<1 #define MAC_CONFIG_NOCFR 1<<0 #define TX_WAIT_SELECT 0x18 #define RX_CHANNEL_CONTROL 0x40 /* Tx channel status */ #define TX_DBDMA_REG 0x00 #define TX_CHANNEL_CONTROL 0x00 #define TX_CHANNEL_STATUS 0x04 #define TX_STATUS_RUN 1<<15 #define TX_STATUS_PAUSE 1<<14 #define TX_STATUS_WAKE 1<<12 #define TX_STATUS_DEAD 1<<11 #define TX_STATUS_ACTIVE 1<<10 #define TX_STATUS_BT 1<<8 #define TX_STATUS_TXABORT 1<<7 #define TX_STATUS_TXSR 1<<6 #define TX_CHANNEL_RUN TX_STATUS_RUN #define TX_CHANNEL_PAUSE TX_STATUS_PAUSE #define TX_CHANNEL_WAKE TX_STATUS_WAKE #define TX_CHANNEL_DEAD TX_STATUS_DEAD #define TX_CHANNEL_ACTIVE TX_STATUS_ACTIVE #define TX_CHANNEL_BT TX_STATUS_BT #define TX_CHANNEL_TXABORT TX_STATUS_TXABORT #define TX_CHANNEL_TXSR TX_STATUS_TXSR #define TX_DBDMA_ENABLE (TX_CHANNEL_WAKE | TX_CHANNEL_PAUSE | \ TX_CHANNEL_RUN ) /* Transmit command ptr lo register */ #define TX_CMD_PTR_LO 0x0c /* Transmit interrupt select register */ #define TX_INT_SELECT 0x10 /* Transmit branch select register */ #define TX_BRANCH_SELECT 0x14 /* Transmit wait select register */ #define TX_WAIT_SELECT 0x18 #define TX_WAIT_STAT_RECV 0x40 /* Rx channel status */ #define RX_DBDMA_REG 0x40 #define RX_CHANNEL_CONTROL 0x40 #define RX_CHANNEL_STATUS 0x44 #define RX_STATUS_RUN 1<<15 #define RX_STATUS_PAUSE 1<<14 #define RX_STATUS_WAKE 1<<12 #define RX_STATUS_DEAD 1<<11 #define RX_STATUS_ACTIVE 1<<10 #define RX_STATUS_BT 1<<8 #define RX_STATUS_EOP 1<<6 #define RX_CHANNEL_RUN RX_STATUS_RUN #define RX_CHANNEL_PAUSE RX_STATUS_PAUSE #define RX_CHANNEL_WAKE RX_STATUS_WAKE #define RX_CHANNEL_DEAD RX_STATUS_DEAD #define RX_CHANNEL_ACTIVE RX_STATUS_ACTIVE #define RX_CHANNEL_BT RX_STATUS_BT #define RX_CHANNEL_EOP RX_STATUS_EOP #define RX_DBDMA_ENABLE (RX_CHANNEL_WAKE | RX_CHANNEL_PAUSE | \ RX_CHANNEL_RUN) /* Receive command ptr lo */ #define RX_CMD_PTR_LO 0x4c /* Receive interrupt select register */ #define RX_INT_SELECT 0x50 #define RX_INT_SELECT_EOP 0x40 /* Receive branch select */ #define RX_BRANCH_SELECT 0x54 #define RX_BRANCH_SELECT_EOP 0x40 /* Receive wait select */ #define RX_WAIT_SELECT 0x58 #define RX_WAIT_SELECT_EOP 0x40 /* Event status register */ #define EVENT_STATUS 0x80 #define EVENT_TXSR 1<<2 #define EVENT_EOP 1<<1 #define EVENT_TXABORT 1<<0 /* Interrupt enable register */ #define INTERRUPT_ENABLE 0x82 /* Interrupt clear register */ #define INTERRUPT_CLEAR 0x84 /* Interrupt status register */ #define INTERRUPT_STATUS_REG 0x86 /* bits for the above three interrupt registers */ #define INTERRUPT_INTE 1<<15 /* interrupt enable */ #define INTERRUPT_WI 1<<9 /* wakeup interrupt */ #define INTERRUPT_ERI 1<<8 /* early receive interrupt */ #define INTERRUPT_PPET 1<<7 /* PCI Tx parity error */ #define INTERRUPT_PBFT 1<<6 /* PCI Tx bus fault */ #define INTERRUPT_IIDT 1<<5 /* illegal instruction Tx */ #define INTERRUPT_DIT 1<<4 /* DBDMA Tx interrupt */ #define INTERRUPT_PPER 1<<3 /* PCI Rx parity error */ #define INTERRUPT_PBFR 1<<2 /* PCI Rx bus fault */ #define INTERRUPT_IIDR 1<<1 /* illegal instruction Rx */ #define INTERRUPT_DIR 1<<0 /* DBDMA Rx interrupt */ #define INTERRUPT_TX_MASK (INTERRUPT_PBFT|INTERRUPT_IIDT| \ INTERRUPT_PPET|INTERRUPT_DIT) #define INTERRUPT_RX_MASK (INTERRUPT_PBFR|INTERRUPT_IIDR| \ INTERRUPT_PPER|INTERRUPT_DIR) /* chip revision register */ #define CHIP_REVISION_REG 0x8c #define CHIP_PCIREV_MASK (0xf<<16) #define CHIP_PCIDEV_MASK 0xff /* Tx threshold register */ #define TX_THRESHOLD 0x94 /* General purpose register */ #define GEN_PURPOSE_REG 0x9e /* General purpose pin control reg */ #define GEN_PIN_CONTROL_REG 0x9f /* DBDMA control register */ #define DBDMA_CONTROL 0x90 #define DBDMA_SRST 1<<31 #define DBDMA_TDPCE 1<<23 #define DBDMA_BE 1<<22 #define DBDMA_TAP_MASK (1<<19|1<<20|1<<21) #define DBDMA_RAP_MASK (1<<16|1<<17|1<<18) #define DBDMA_DPMRLE 1<<15 #define DBDMA_WIE 1<<14 #define DBDMA_MP 1<<13 #define DBDMA_SME 1<<12 #define DBDMA_CME 1<<11 #define DBDMA_DDPE 1<<10 #define DBDMA_TDPE 1<<9 #define DBDMA_EXTE 1<<8 #define DBDMA_BST_MASK (1<<4|1<<5|1<<6) #define DBDMA_BSR_MASK (1<<0|1<<1|1<<2) #define DBDMA_BURST_1 (0x00) #define DBDMA_BURST_2 (0x01) #define DBDMA_BURST_4 (0x02) #define DBDMA_BURST_8 (0x03) #define DBDMA_BURST_16 (0x04) #define DBDMA_BURST_32 (0x05) #define DBDMA_BURST_64 (0x06) #define DBDMA_BURST_128 (0x07) #define DBDMA_TX_BST_SHIFT (4) #define DBDMA_RX_BST_SHIFT (0) #define DBDMA_TX_ARBITRATION_DEFAULT ( 1 << 19 ) #define DBDMA_RX_ARBITRATION_DEFAULT ( 2 << 16 ) /* Back-to-back interpacket gap register */ #define BTOB_INTP_GAP 0xa2 #define BTOB_INTP_DEFAULT 0x18 /* Non-back-to-back interpacket gap register */ #define NBTOB_INTP_GAP 0xa4 /* MIIM command register */ #define MIIM_COMMAND 0xa6 #define MIIM_SCAN 1<<1 #define MIIM_RSTAT 1<<0 /* MII address register */ #define MII_ADDRESS 0xa8 #define MII_FIAD_MASK (1<<8|1<<9|1<<10|1<<11|1<<12) #define MII_RGAD_MASK (1<<0|1<<1|1<<2|1<<3|1<<4) #define TPPMD_CONTROL_REG 0xa8 #define TPPMD_FO 1<<1 #define TPPMD_LB 1<<0 /* MII read and write registers */ #define MII_WRITE_DATA 0xaa #define MII_READ_DATA 0xac /* MII indicators */ #define MII_INDICATOR 0xae #define MII_NVALID 1<<2 #define MII_SCAN 1<<1 #define MII_BUSY 1<<0 /* Address filter */ #define ADDRESS_FILTER 0xd0 #define ADDRESS_RPPRM 1<<3 /* multicast promis. mode */ #define ADDRESS_RPPRO 1<<2 /* promiscuous mode */ #define ADDRESS_RPAMC 1<<1 /* accept multicasts */ #define ADDRESS_RPABC 1<<0 /* accept broadcasts */ /* Station addresses Note that if the serial EEPROM is disabled, these values are all zero. If, like us, you get the chips when they're fresh, they're also zero and you have to initialize the address */ #define STATION_ADDRESS_0 0xd2 #define STATION_ADDRESS_1 0xd4 #define STATION_ADDRESS_2 0xd6 /* Hash tables */ #define HASH_TABLE_0 0xd8 #define HASH_TABLE_1 0xda #define HASH_TABLE_2 0xdc #define HASH_TABLE_3 0xde /* PHY indentifiers */ #define PHY_IDENTIFIER_0 0xe4 #define PHY_IDENTIFIER_1 0xe6 /* MII Auto-negotiation register definitions */ #define MII_AUTO_NEGOTIATION_CONTROL (0x0000) #define MANC_PHY_RESET (0x8000) #define MANC_PHY_LOOPBACK_ENABLE (0x4000) #define MANC_PHY_LOOPBACK_DISABLE (0x0000) #define MANC_PHY_SPEED_100 (0x2000) #define MANC_PHY_SPEED_10 (0x0000) #define MANC_AUTO_NEGOTIATION_ENABLE (0x1000) #define MANC_AUTO_NEGOTIATION_DISABLE (0x0000) #define MANC_PHY_POWER_DOWN (0x0800) #define MANC_PHY_POWER_UP (0x0000) #define MANC_ISOLATE_ENABLE (0x0400) #define MANC_ISOLATE_DISABLE (0x0000) #define MANC_RESTART_AUTO_NEGOTIATION (0x0200) #define MANC_FULL_DUPLEX (0x0100) #define MANC_HALF_DUPLEX (0x0000) #define MII_AUTO_NEGOTIATION_STATUS (0x0001) #define MANS_100BASE_T4_HALF_DUPLEX (0x8000) #define MANS_100BASE_X_FULL_DUPLEX (0x4000) #define MANS_100BASE_X_HALF_DUPLEX (0x2000) #define MANS_10MBS_FULL_DUPLEX (0x1000) #define MANS_10MBS_HALF_DUPLEX (0x0800) #define MANS_AUTO_NEGOTIATION_COMPLETE (0x0020) #define MANS_REMOTE_FAULT (0x0010) #define MANS_AUTO_NEGOTIATION_ABILITY (0x0008) #define MANS_LINK_STATUS (0x0004) #define MANS_JABBER_DETECT (0x0002) #define MANS_EXTENDED_CAPABILITY (0x0001) #define MII_PHY_IDENTIFIER_1 (0x0002) #define MII_PHY_IDENTIFIER_2 (0x0003) #define MII_AUTO_NEGOTIATION_ADVERTISEMENT (0x0004) #define MANA_NEXT_PAGE (0x8000) #define MANA_REMOTE_FAULT (0x2000) #define MANA_TECHNOLOGY_ABILITY_MASK (0x1FE0) #define MANATECH_10BASET_HALF_DUPLEX (0x0020) #define MANATECH_10BASET_FULL_DUPLEX (0x0040) #define MANATECH_100BASETX_HALF_DUPLEX (0x0080) #define MANATECH_100BASETX_FULL_DUPLEX (0x0100) #define MANATECH_100BASET4 (0x0200) #define MANA_SELECTOR_MASK (0x001F) #define MANASELECTOR_802_3 (0x0001) #define MII_AUTO_NEGOTIATION_LINK_PARTNER (0x0005) #define MANLP_NEXT_PAGE (0x8000) #define MANLP_ACKNOWLEDGE (0x4000) #define MANLP_REMOTE_FAULT (0x2000) #define MANLP_TECHNOLOGY_ABILITY_MASK (0x1FE0) #define MANLP_SELECTOR_MASK (0x001F) #define MII_AUTO_NEGOTIATION_EXPANSION (0x0006) #define MANE_PARALLEL_DETECTION_FAULT (0x0010) #define MANE_LINK_PARTNER_NEXT_PAGE_ABLE (0x0008) #define MANE_NEXT_PAGE_ABLE (0x0004) #define MANE_PAGE_RECEIVED (0x0002) #define MANE_LINK_PARTNER_AUTO_ABLE (0x0001) #define MII_AUTO_NEGOTIATION_NEXT_PAGE_TRANSMIT (0x0007) #define MANNPT_NEXT_PAGE (0x8000) #define MANNPT_MESSAGE_PAGE (0x2000) #define MANNPT_ACKNOWLEDGE_2 (0x1000) #define MANNPT_TOGGLE (0x0800) #define MANNPT_MESSAGE_FIELD_MASK (0x07FF) #endif