/* * Generic Generic NCR5380 driver * * Copyright 1993, Drew Eckhardt * Visionary Computing * (Unix and Linux consulting and custom programming) * drew@colorado.edu * +1 (303) 440-4894 * * NCR53C400 extensions (c) 1994,1995,1996, Kevin Lentin * K.Lentin@cs.monash.edu.au * * NCR53C400A extensions (c) 1996, Ingmar Baumgart * ingmar@gonzo.schwaben.de * * DTC3181E extensions (c) 1997, Ronald van Cuijlenborg * ronald.van.cuijlenborg@tip.nl or nutty@dds.nl * * Added ISAPNP support for DTC436 adapters, * Thomas Sailer, sailer@ife.ee.ethz.ch * * ALPHA RELEASE 1. * * For more information, please consult * * NCR 5380 Family * SCSI Protocol Controller * Databook * * NCR Microelectronics * 1635 Aeroplaza Drive * Colorado Springs, CO 80916 * 1+ (719) 578-3400 * 1+ (800) 334-5454 */ /* * TODO : flesh out DMA support, find some one actually using this (I have * a memory mapped Trantor board that works fine) */ /* * Options : * * PARITY - enable parity checking. Not supported. * * SCSI2 - enable support for SCSI-II tagged queueing. Untested. * * USLEEP - enable support for devices that don't disconnect. Untested. * * The card is detected and initialized in one of several ways : * 1. With command line overrides - NCR5380=port,irq may be * used on the LILO command line to override the defaults. * * 2. With the GENERIC_NCR5380_OVERRIDE compile time define. This is * specified as an array of address, irq, dma, board tuples. Ie, for * one board at 0x350, IRQ5, no dma, I could say * -DGENERIC_NCR5380_OVERRIDE={{0xcc000, 5, DMA_NONE, BOARD_NCR5380}} * * -1 should be specified for no or DMA interrupt, -2 to autoprobe for an * IRQ line if overridden on the command line. * * 3. When included as a module, with arguments passed on the command line: * ncr_irq=xx the interrupt * ncr_addr=xx the port or base address (for port or memory * mapped, resp.) * ncr_dma=xx the DMA * ncr_5380=1 to set up for a NCR5380 board * ncr_53c400=1 to set up for a NCR53C400 board * e.g. * modprobe g_NCR5380 ncr_irq=5 ncr_addr=0x350 ncr_5380=1 * for a port mapped NCR5380 board or * modprobe g_NCR5380 ncr_irq=255 ncr_addr=0xc8000 ncr_53c400=1 * for a memory mapped NCR53C400 board with interrupts disabled. * * 255 should be specified for no or DMA interrupt, 254 to autoprobe for an * IRQ line if overridden on the command line. * */ /* * $Log: generic_NCR5380.c,v $ */ /* settings for DTC3181E card with only Mustek scanner attached */ #define USLEEP #define USLEEP_POLL 1 #define USLEEP_SLEEP 20 #define USLEEP_WAITLONG 500 #define AUTOPROBE_IRQ #define AUTOSENSE #include #ifdef CONFIG_SCSI_GENERIC_NCR53C400 #define NCR53C400_PSEUDO_DMA 1 #define PSEUDO_DMA #define NCR53C400 #define NCR5380_STATS #undef NCR5380_STAT_LIMIT #endif #if defined(CONFIG_SCSI_G_NCR5380_PORT) && defined(CONFIG_SCSI_G_NCR5380_MEM) #error You can not configure the Generic NCR 5380 SCSI Driver for memory mapped I/O and port mapped I/O at the same time (yet) #endif #if !defined(CONFIG_SCSI_G_NCR5380_PORT) && !defined(CONFIG_SCSI_G_NCR5380_MEM) #error You must configure the Generic NCR 5380 SCSI Driver for one of memory mapped I/O and port mapped I/O. #endif #include #include #include #include #include #include "scsi.h" #include "hosts.h" #include "g_NCR5380.h" #include "NCR5380.h" #include "constants.h" #include "sd.h" #include #include #include #include #define NCR_NOT_SET 0 static int ncr_irq=NCR_NOT_SET; static int ncr_dma=NCR_NOT_SET; static int ncr_addr=NCR_NOT_SET; static int ncr_5380=NCR_NOT_SET; static int ncr_53c400=NCR_NOT_SET; static int ncr_53c400a=NCR_NOT_SET; static int dtc_3181e=NCR_NOT_SET; static struct override { NCR5380_implementation_fields; int irq; int dma; int board; /* Use NCR53c400, Ricoh, etc. extensions ? */ } overrides #ifdef GENERIC_NCR5380_OVERRIDE [] __initdata = GENERIC_NCR5380_OVERRIDE; #else [1] __initdata = {{0,},}; #endif #define NO_OVERRIDES (sizeof(overrides) / sizeof(struct override)) /* * Function : static internal_setup(int board, char *str, int *ints) * * Purpose : LILO command line initialization of the overrides array, * * Inputs : board - either BOARD_NCR5380 for a normal NCR5380 board, * or BOARD_NCR53C400 for a NCR53C400 board. str - unused, ints - * array of integer parameters with ints[0] equal to the number of ints. * */ static void __init internal_setup(int board, char *str, int *ints){ static int commandline_current = 0; switch (board) { case BOARD_NCR5380: if (ints[0] != 2 && ints[0] != 3) { printk("generic_NCR5380_setup : usage ncr5380=" STRVAL(NCR5380_map_name) ",irq,dma\n"); return; } break; case BOARD_NCR53C400: if (ints[0] != 2) { printk("generic_NCR53C400_setup : usage ncr53c400=" STRVAL(NCR5380_map_name) ",irq\n"); return; } break; case BOARD_NCR53C400A: if (ints[0] != 2) { printk("generic_NCR53C400A_setup : usage ncr53c400a=" STRVAL(NCR5380_map_name) ",irq\n"); return; } break; case BOARD_DTC3181E: if (ints[0] != 2) { printk("generic_DTC3181E_setup : usage dtc3181e=" STRVAL(NCR5380_map_name) ",irq\n"); return; } break; } if (commandline_current < NO_OVERRIDES) { overrides[commandline_current].NCR5380_map_name = (NCR5380_map_type)ints[1]; overrides[commandline_current].irq = ints[2]; if (ints[0] == 3) overrides[commandline_current].dma = ints[3]; else overrides[commandline_current].dma = DMA_NONE; overrides[commandline_current].board = board; ++commandline_current; } } /* * Function : generic_NCR5380_setup (char *str, int *ints) * * Purpose : LILO command line initialization of the overrides array, * * Inputs : str - unused, ints - array of integer parameters with ints[0] * equal to the number of ints. */ void __init generic_NCR5380_setup (char *str, int *ints){ internal_setup (BOARD_NCR5380, str, ints); } /* * Function : generic_NCR53C400_setup (char *str, int *ints) * * Purpose : LILO command line initialization of the overrides array, * * Inputs : str - unused, ints - array of integer parameters with ints[0] * equal to the number of ints. */ void __init generic_NCR53C400_setup (char *str, int *ints){ internal_setup (BOARD_NCR53C400, str, ints); } /* * Function : generic_NCR53C400A_setup (char *str, int *ints) * * Purpose : LILO command line initialization of the overrides array, * * Inputs : str - unused, ints - array of integer parameters with ints[0] * equal to the number of ints. */ void generic_NCR53C400A_setup (char *str, int *ints) { internal_setup (BOARD_NCR53C400A, str, ints); } /* * Function : generic_DTC3181E_setup (char *str, int *ints) * * Purpose : LILO command line initialization of the overrides array, * * Inputs : str - unused, ints - array of integer parameters with ints[0] * equal to the number of ints. */ void generic_DTC3181E_setup (char *str, int *ints) { internal_setup (BOARD_DTC3181E, str, ints); } /* * Function : int generic_NCR5380_detect(Scsi_Host_Template * tpnt) * * Purpose : initializes generic NCR5380 driver based on the * command line / compile time port and irq definitions. * * Inputs : tpnt - template for this SCSI adapter. * * Returns : 1 if a host adapter was found, 0 if not. * */ int __init generic_NCR5380_detect(Scsi_Host_Template * tpnt){ static int current_override = 0; int count, i; u_int *ports; u_int ncr_53c400a_ports[] = {0x280, 0x290, 0x300, 0x310, 0x330, 0x340, 0x348, 0x350, 0}; u_int dtc_3181e_ports[] = {0x220, 0x240, 0x280, 0x2a0, 0x2c0, 0x300, 0x320, 0x340, 0}; int flags = 0; struct Scsi_Host *instance; if (ncr_irq != NCR_NOT_SET) overrides[0].irq=ncr_irq; if (ncr_dma != NCR_NOT_SET) overrides[0].dma=ncr_dma; if (ncr_addr != NCR_NOT_SET) overrides[0].NCR5380_map_name=(NCR5380_map_type)ncr_addr; if (ncr_5380 != NCR_NOT_SET) overrides[0].board=BOARD_NCR5380; else if (ncr_53c400 != NCR_NOT_SET) overrides[0].board=BOARD_NCR53C400; else if (ncr_53c400a != NCR_NOT_SET) overrides[0].board=BOARD_NCR53C400A; else if (dtc_3181e != NCR_NOT_SET) overrides[0].board=BOARD_DTC3181E; if (!current_override && isapnp_present()) { struct pci_dev *dev = NULL; count = 0; while ((dev = isapnp_find_dev(NULL, ISAPNP_VENDOR('D','T','C'), ISAPNP_FUNCTION(0x436e), dev))) { if (count >= NO_OVERRIDES) break; if (!dev->active && dev->prepare(dev) < 0) { printk(KERN_ERR "dtc436e probe: prepare failed\n"); continue; } if (!(dev->resource[0].flags & IORESOURCE_IO)) continue; if (!dev->active && dev->activate(dev) < 0) { printk(KERN_ERR "dtc436e probe: activate failed\n"); continue; } if (dev->irq_resource[0].flags & IORESOURCE_IRQ) overrides[count].irq=dev->irq_resource[0].start; else overrides[count].irq=IRQ_NONE; if (dev->dma_resource[0].flags & IORESOURCE_DMA) overrides[count].dma=dev->dma_resource[0].start; else overrides[count].dma=DMA_NONE; overrides[count].NCR5380_map_name=(NCR5380_map_type)dev->resource[0].start; overrides[count].board=BOARD_DTC3181E; count++; } } tpnt->proc_name = "g_NCR5380"; for (count = 0; current_override < NO_OVERRIDES; ++current_override) { if (!(overrides[current_override].NCR5380_map_name)) continue; ports = 0; switch (overrides[current_override].board) { case BOARD_NCR5380: flags = FLAG_NO_PSEUDO_DMA; break; case BOARD_NCR53C400: flags = FLAG_NCR53C400; break; case BOARD_NCR53C400A: flags = FLAG_NO_PSEUDO_DMA; ports = ncr_53c400a_ports; break; case BOARD_DTC3181E: flags = FLAG_NO_PSEUDO_DMA | FLAG_DTC3181E; ports = dtc_3181e_ports; break; } #ifdef CONFIG_SCSI_G_NCR5380_PORT if (ports) { /* wakeup sequence for the NCR53C400A and DTC3181E*/ /* Disable the adapter and look for a free io port */ outb(0x59, 0x779); outb(0xb9, 0x379); outb(0xc5, 0x379); outb(0xae, 0x379); outb(0xa6, 0x379); outb(0x00, 0x379); if (overrides[current_override].NCR5380_map_name != PORT_AUTO) for(i=0; ports[i]; i++) { if (overrides[current_override].NCR5380_map_name == ports[i]) break; } else for(i=0; ports[i]; i++) { if ((!check_region(ports[i], 16)) && (inb(ports[i]) == 0xff)) break; } if (ports[i]) { outb(0x59, 0x779); outb(0xb9, 0x379); outb(0xc5, 0x379); outb(0xae, 0x379); outb(0xa6, 0x379); outb(0x80 | i, 0x379); /* set io port to be used */ outb(0xc0, ports[i] + 9); if (inb(ports[i] + 9) != 0x80) continue; else overrides[current_override].NCR5380_map_name=ports[i]; } else continue; } request_region(overrides[current_override].NCR5380_map_name, NCR5380_region_size, "ncr5380"); #else if(check_mem_region(overrides[current_override].NCR5380_map_name, NCR5380_region_size)) continue; request_mem_region(overrides[current_override].NCR5380_map_name, NCR5380_region_size, "ncr5380"); #endif instance = scsi_register (tpnt, sizeof(struct NCR5380_hostdata)); if(instance == NULL) { #ifdef CONFIG_SCSI_G_NCR5380_PORT release_region(overrides[current_override].NCR5380_map_name, NCR5380_region_size); #else release_mem_region(overrides[current_override].NCR5380_map_name, NCR5380_region_size); #endif } instance->NCR5380_instance_name = overrides[current_override].NCR5380_map_name; NCR5380_init(instance, flags); if (overrides[current_override].irq != IRQ_AUTO) instance->irq = overrides[current_override].irq; else instance->irq = NCR5380_probe_irq(instance, 0xffff); if (instance->irq != IRQ_NONE) if (request_irq(instance->irq, do_generic_NCR5380_intr, SA_INTERRUPT, "NCR5380", NULL)) { printk("scsi%d : IRQ%d not free, interrupts disabled\n", instance->host_no, instance->irq); instance->irq = IRQ_NONE; } if (instance->irq == IRQ_NONE) { printk("scsi%d : interrupts not enabled. for better interactive performance,\n", instance->host_no); printk("scsi%d : please jumper the board for a free IRQ.\n", instance->host_no); } printk("scsi%d : at " STRVAL(NCR5380_map_name) " 0x%x", instance->host_no, (unsigned int)instance->NCR5380_instance_name); if (instance->irq == IRQ_NONE) printk (" interrupts disabled"); else printk (" irq %d", instance->irq); printk(" options CAN_QUEUE=%d CMD_PER_LUN=%d release=%d", CAN_QUEUE, CMD_PER_LUN, GENERIC_NCR5380_PUBLIC_RELEASE); NCR5380_print_options(instance); printk("\n"); ++current_override; ++count; } return count; } const char * generic_NCR5380_info (struct Scsi_Host* host) { static const char string[]="Generic NCR5380/53C400 Driver"; return string; } int generic_NCR5380_release_resources(struct Scsi_Host * instance) { NCR5380_local_declare(); NCR5380_setup(instance); #ifdef CONFIG_SCSI_G_NCR5380_PORT release_region(instance->NCR5380_instance_name, NCR5380_region_size); #else release_mem_region(instance->NCR5380_instance_name, NCR5380_region_size); #endif if (instance->irq != IRQ_NONE) free_irq(instance->irq, NULL); return 0; } #ifdef BIOSPARAM /* * Function : int generic_NCR5380_biosparam(Disk * disk, kdev_t dev, int *ip) * * Purpose : Generates a BIOS / DOS compatible H-C-S mapping for * the specified device / size. * * Inputs : size = size of device in sectors (512 bytes), dev = block device * major / minor, ip[] = {heads, sectors, cylinders} * * Returns : always 0 (success), initializes ip * */ /* * XXX Most SCSI boards use this mapping, I could be incorrect. Some one * using hard disks on a trantor should verify that this mapping corresponds * to that used by the BIOS / ASPI driver by running the linux fdisk program * and matching the H_C_S coordinates to what DOS uses. */ int generic_NCR5380_biosparam(Disk * disk, kdev_t dev, int *ip) { int size = disk->capacity; ip[0] = 64; ip[1] = 32; ip[2] = size >> 11; return 0; } #endif #if NCR53C400_PSEUDO_DMA static inline int NCR5380_pread (struct Scsi_Host *instance, unsigned char *dst, int len) { int blocks = len / 128; int start = 0; int bl; #ifdef CONFIG_SCSI_G_NCR5380_PORT int i; #endif NCR5380_local_declare(); NCR5380_setup(instance); #if (NDEBUG & NDEBUG_C400_PREAD) printk("53C400r: About to read %d blocks for %d bytes\n", blocks, len); #endif NCR5380_write(C400_CONTROL_STATUS_REG, CSR_BASE | CSR_TRANS_DIR); NCR5380_write(C400_BLOCK_COUNTER_REG, blocks); while (1) { #if (NDEBUG & NDEBUG_C400_PREAD) printk("53C400r: %d blocks left\n", blocks); #endif if ((bl=NCR5380_read(C400_BLOCK_COUNTER_REG)) == 0) { #if (NDEBUG & NDEBUG_C400_PREAD) if (blocks) printk("53C400r: blocks still == %d\n", blocks); else printk("53C400r: Exiting loop\n"); #endif break; } #if 1 if (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ) { printk("53C400r: Got 53C80_IRQ start=%d, blocks=%d\n", start, blocks); return -1; } #endif #if (NDEBUG & NDEBUG_C400_PREAD) printk("53C400r: Waiting for buffer, bl=%d\n", bl); #endif while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY) ; #if (NDEBUG & NDEBUG_C400_PREAD) printk("53C400r: Transferring 128 bytes\n"); #endif #ifdef CONFIG_SCSI_G_NCR5380_PORT for (i=0; i<128; i++) dst[start+i] = NCR5380_read(C400_HOST_BUFFER); #else /* implies CONFIG_SCSI_G_NCR5380_MEM */ isa_memcpy_fromio(dst+start,NCR53C400_host_buffer+NCR5380_map_name,128); #endif start+=128; blocks--; } if (blocks) { #if (NDEBUG & NDEBUG_C400_PREAD) printk("53C400r: EXTRA: Waiting for buffer\n"); #endif while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY) ; #if (NDEBUG & NDEBUG_C400_PREAD) printk("53C400r: Transferring EXTRA 128 bytes\n"); #endif #ifdef CONFIG_SCSI_G_NCR5380_PORT for (i=0; i<128; i++) dst[start+i] = NCR5380_read(C400_HOST_BUFFER); #else /* implies CONFIG_SCSI_G_NCR5380_MEM */ isa_memcpy_fromio(dst+start,NCR53C400_host_buffer+NCR5380_map_name,128); #endif start+=128; blocks--; } #if (NDEBUG & NDEBUG_C400_PREAD) else printk("53C400r: No EXTRA required\n"); #endif #if (NDEBUG & NDEBUG_C400_PREAD) printk("53C400r: Final values: blocks=%d start=%d\n", blocks, start); #endif if (!(NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ)) printk("53C400r: no 53C80 gated irq after transfer"); #if (NDEBUG & NDEBUG_C400_PREAD) else printk("53C400r: Got 53C80 interrupt and tried to clear it\n"); #endif /* DON'T DO THIS - THEY NEVER ARRIVE! printk("53C400r: Waiting for 53C80 registers\n"); while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_53C80_REG) ; */ if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_END_DMA_TRANSFER)) printk("53C400r: no end dma signal\n"); #if (NDEBUG & NDEBUG_C400_PREAD) else printk("53C400r: end dma as expected\n"); #endif NCR5380_write(MODE_REG, MR_BASE); NCR5380_read(RESET_PARITY_INTERRUPT_REG); return 0; } static inline int NCR5380_pwrite (struct Scsi_Host *instance, unsigned char *src, int len) { int blocks = len / 128; int start = 0; int i; int bl; NCR5380_local_declare(); NCR5380_setup(instance); #if (NDEBUG & NDEBUG_C400_PWRITE) printk("53C400w: About to write %d blocks for %d bytes\n", blocks, len); #endif NCR5380_write(C400_CONTROL_STATUS_REG, CSR_BASE); NCR5380_write(C400_BLOCK_COUNTER_REG, blocks); while (1) { if (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ) { printk("53C400w: Got 53C80_IRQ start=%d, blocks=%d\n", start, blocks); return -1; } if ((bl=NCR5380_read(C400_BLOCK_COUNTER_REG)) == 0) { #if (NDEBUG & NDEBUG_C400_PWRITE) if (blocks) printk("53C400w: exiting loop, blocks still == %d\n", blocks); else printk("53C400w: exiting loop\n"); #endif break; } #if (NDEBUG & NDEBUG_C400_PWRITE) printk("53C400w: %d blocks left\n", blocks); printk("53C400w: waiting for buffer, bl=%d\n", bl); #endif while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY) ; #if (NDEBUG & NDEBUG_C400_PWRITE) printk("53C400w: transferring 128 bytes\n"); #endif #ifdef CONFIG_SCSI_G_NCR5380_PORT for (i=0; i<128; i++) NCR5380_write(C400_HOST_BUFFER, src[start+i]); #else /* implies CONFIG_SCSI_G_NCR5380_MEM */ isa_memcpy_toio(NCR53C400_host_buffer+NCR5380_map_name,src+start,128); #endif start+=128; blocks--; } if (blocks) { #if (NDEBUG & NDEBUG_C400_PWRITE) printk("53C400w: EXTRA waiting for buffer\n"); #endif while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY) ; #if (NDEBUG & NDEBUG_C400_PWRITE) printk("53C400w: transferring EXTRA 128 bytes\n"); #endif #ifdef CONFIG_SCSI_G_NCR5380_PORT for (i=0; i<128; i++) NCR5380_write(C400_HOST_BUFFER, src[start+i]); #else /* implies CONFIG_SCSI_G_NCR5380_MEM */ isa_memcpy_toio(NCR53C400_host_buffer+NCR5380_map_name,src+start,128); #endif start+=128; blocks--; } #if (NDEBUG & NDEBUG_C400_PWRITE) else printk("53C400w: No EXTRA required\n"); #endif #if (NDEBUG & NDEBUG_C400_PWRITE) printk("53C400w: Final values: blocks=%d start=%d\n", blocks, start); #endif #if 0 printk("53C400w: waiting for registers to be available\n"); THEY NEVER DO! while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_53C80_REG) ; printk("53C400w: Got em\n"); #endif /* Let's wait for this instead - could be ugly */ /* All documentation says to check for this. Maybe my hardware is too * fast. Waiting for it seems to work fine! KLL */ while (!(i = NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ)) ; /* * I know. i is certainly != 0 here but the loop is new. See previous * comment. */ if (i) { #if (NDEBUG & NDEBUG_C400_PWRITE) printk("53C400w: got 53C80 gated irq (last block)\n"); #endif if (!((i=NCR5380_read(BUS_AND_STATUS_REG)) & BASR_END_DMA_TRANSFER)) printk("53C400w: No END OF DMA bit - WHOOPS! BASR=%0x\n",i); #if (NDEBUG & NDEBUG_C400_PWRITE) else printk("53C400w: Got END OF DMA\n"); #endif } else printk("53C400w: no 53C80 gated irq after transfer (last block)\n"); #if 0 if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_END_DMA_TRANSFER)) { printk("53C400w: no end dma signal\n"); } #endif #if (NDEBUG & NDEBUG_C400_PWRITE) printk("53C400w: waiting for last byte...\n"); #endif while (!(NCR5380_read(TARGET_COMMAND_REG) & TCR_LAST_BYTE_SENT)) ; #if (NDEBUG & NDEBUG_C400_PWRITE) printk("53C400w: got last byte.\n"); printk("53C400w: pwrite exiting with status 0, whoopee!\n"); #endif return 0; } #endif /* PSEUDO_DMA */ #include "NCR5380.c" #define PRINTP(x) len += sprintf(buffer+len, x) #define ANDP , static int sprint_opcode(char* buffer, int len, int opcode) { int start = len; PRINTP("0x%02x " ANDP opcode); return len-start; } static int sprint_command (char* buffer, int len, unsigned char *command) { int i,s,start=len; len += sprint_opcode(buffer, len, command[0]); for ( i = 1, s = COMMAND_SIZE(command[0]); i < s; ++i) PRINTP("%02x " ANDP command[i]); PRINTP("\n"); return len-start; } static int sprint_Scsi_Cmnd (char* buffer, int len, Scsi_Cmnd *cmd) { int start = len; PRINTP("host number %d destination target %d, lun %d\n" ANDP cmd->host->host_no ANDP cmd->target ANDP cmd->lun); PRINTP(" command = "); len += sprint_command (buffer, len, cmd->cmnd); return len-start; } int generic_NCR5380_proc_info(char* buffer, char** start, off_t offset, int length, int hostno, int inout) { int len = 0; NCR5380_local_declare(); unsigned long flags; unsigned char status; int i; struct Scsi_Host *scsi_ptr; Scsi_Cmnd *ptr; struct NCR5380_hostdata *hostdata; #ifdef NCR5380_STATS Scsi_Device *dev; extern const char *const scsi_device_types[MAX_SCSI_DEVICE_CODE]; #endif save_flags(flags); cli(); for (scsi_ptr = first_instance; scsi_ptr; scsi_ptr=scsi_ptr->next) if (scsi_ptr->host_no == hostno) break; NCR5380_setup(scsi_ptr); hostdata = (struct NCR5380_hostdata *)scsi_ptr->hostdata; PRINTP("SCSI host number %d : %s\n" ANDP scsi_ptr->host_no ANDP scsi_ptr->hostt->name); PRINTP("Generic NCR5380 driver version %d\n" ANDP GENERIC_NCR5380_PUBLIC_RELEASE); PRINTP("NCR5380 core version %d\n" ANDP NCR5380_PUBLIC_RELEASE); #ifdef NCR53C400 PRINTP("NCR53C400 extension version %d\n" ANDP NCR53C400_PUBLIC_RELEASE); PRINTP("NCR53C400 card%s detected\n" ANDP (((struct NCR5380_hostdata *)scsi_ptr->hostdata)->flags & FLAG_NCR53C400)?"":" not"); # if NCR53C400_PSEUDO_DMA PRINTP("NCR53C400 pseudo DMA used\n"); # endif #else PRINTP("NO NCR53C400 driver extensions\n"); #endif PRINTP("Using %s mapping at %s 0x%lx, " ANDP STRVAL(NCR5380_map_config) ANDP STRVAL(NCR5380_map_name) ANDP scsi_ptr->NCR5380_instance_name); if (scsi_ptr->irq == IRQ_NONE) PRINTP("no interrupt\n"); else PRINTP("on interrupt %d\n" ANDP scsi_ptr->irq); #ifdef NCR5380_STATS if (hostdata->connected || hostdata->issue_queue || hostdata->disconnected_queue) PRINTP("There are commands pending, transfer rates may be crud\n"); if (hostdata->pendingr) PRINTP(" %d pending reads" ANDP hostdata->pendingr); if (hostdata->pendingw) PRINTP(" %d pending writes" ANDP hostdata->pendingw); if (hostdata->pendingr || hostdata->pendingw) PRINTP("\n"); for (dev = scsi_ptr->host_queue; dev; dev=dev->next) { unsigned long br = hostdata->bytes_read[dev->id]; unsigned long bw = hostdata->bytes_write[dev->id]; long tr = hostdata->time_read[dev->id] / HZ; long tw = hostdata->time_write[dev->id] / HZ; PRINTP(" T:%d %s " ANDP dev->id ANDP (dev->type < MAX_SCSI_DEVICE_CODE) ? scsi_device_types[(int)dev->type] : "Unknown"); for (i=0; i<8; i++) if (dev->vendor[i] >= 0x20) *(buffer+(len++)) = dev->vendor[i]; *(buffer+(len++)) = ' '; for (i=0; i<16; i++) if (dev->model[i] >= 0x20) *(buffer+(len++)) = dev->model[i]; *(buffer+(len++)) = ' '; for (i=0; i<4; i++) if (dev->rev[i] >= 0x20) *(buffer+(len++)) = dev->rev[i]; *(buffer+(len++)) = ' '; PRINTP("\n%10ld kb read in %5ld secs" ANDP br/1024 ANDP tr); if (tr) PRINTP(" @ %5ld bps" ANDP br / tr); PRINTP("\n%10ld kb written in %5ld secs" ANDP bw/1024 ANDP tw); if (tw) PRINTP(" @ %5ld bps" ANDP bw / tw); PRINTP("\n"); } #endif status = NCR5380_read(STATUS_REG); if (!(status & SR_REQ)) PRINTP("REQ not asserted, phase unknown.\n"); else { for (i = 0; (phases[i].value != PHASE_UNKNOWN) && (phases[i].value != (status & PHASE_MASK)); ++i) ; PRINTP("Phase %s\n" ANDP phases[i].name); } if (!hostdata->connected) { PRINTP("No currently connected command\n"); } else { len += sprint_Scsi_Cmnd (buffer, len, (Scsi_Cmnd *) hostdata->connected); } PRINTP("issue_queue\n"); for (ptr = (Scsi_Cmnd *) hostdata->issue_queue; ptr; ptr = (Scsi_Cmnd *) ptr->host_scribble) len += sprint_Scsi_Cmnd (buffer, len, ptr); PRINTP("disconnected_queue\n"); for (ptr = (Scsi_Cmnd *) hostdata->disconnected_queue; ptr; ptr = (Scsi_Cmnd *) ptr->host_scribble) len += sprint_Scsi_Cmnd (buffer, len, ptr); *start = buffer + offset; len -= offset; if (len > length) len = length; restore_flags(flags); return len; } #undef PRINTP #undef ANDP /* Eventually this will go into an include file, but this will be later */ static Scsi_Host_Template driver_template = GENERIC_NCR5380; #include #include "scsi_module.c" #ifdef MODULE MODULE_PARM(ncr_irq, "i"); MODULE_PARM(ncr_dma, "i"); MODULE_PARM(ncr_addr, "i"); MODULE_PARM(ncr_5380, "i"); MODULE_PARM(ncr_53c400, "i"); MODULE_PARM(ncr_53c400a, "i"); MODULE_PARM(dtc_3181e, "i"); #else static int __init do_NCR5380_setup(char *str) { int ints[10]; get_options(str, sizeof(ints)/sizeof(int), ints); generic_NCR5380_setup(str,ints); return 1; } static int __init do_NCR53C400_setup(char *str) { int ints[10]; get_options(str, sizeof(ints)/sizeof(int), ints); generic_NCR53C400_setup(str,ints); return 1; } static int __init do_NCR53C400A_setup(char *str) { int ints[10]; get_options(str, sizeof(ints)/sizeof(int), ints); generic_NCR53C400A_setup(str,ints); return 1; } static int __init do_DTC3181E_setup(char *str) { int ints[10]; get_options(str, sizeof(ints)/sizeof(int), ints); generic_DTC3181E_setup(str,ints); return 1; } __setup("ncr5380=", do_NCR5380_setup); __setup("ncr53c400=", do_NCR53C400_setup); __setup("ncr53c400a=", do_NCR53C400A_setup); __setup("dtc3181e=", do_DTC3181E_setup); static struct isapnp_device_id id_table[] __devinitdata = { { ISAPNP_ANY_ID, ISAPNP_ANY_ID, ISAPNP_VENDOR('D','T','C'), ISAPNP_FUNCTION(0x436e), 0 }, {0} }; MODULE_DEVICE_TABLE(isapnp, id_table); #endif