/* * QLogic ISP1020 Intelligent SCSI Processor Driver (PCI) * Written by Erik H. Moe, ehm@cris.com * Copyright 1995, Erik H. Moe * Copyright 1996, 1997 Michael A. Griffith * * This program is free software; you can redistribute it and/or modify it * under the terms of the GNU General Public License as published by the * Free Software Foundation; either version 2, or (at your option) any * later version. * * This program is distributed in the hope that it will be useful, but * WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU * General Public License for more details. */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include "sd.h" #include "hosts.h" #include "qlogicisp.h" /* Configuration section *****************************************************/ /* Set the following macro to 1 to reload the ISP1020's firmware. This is the latest firmware provided by QLogic. This may be an earlier/later revision than supplied by your board. */ #define RELOAD_FIRMWARE 1 /* Set the following macro to 1 to reload the ISP1020's defaults from nvram. If you are not sure of your settings, leave this alone, the driver will use a set of 'safe' defaults */ #define USE_NVRAM_DEFAULTS 0 /* Macros used for debugging */ #define DEBUG_ISP1020 0 #define DEBUG_ISP1020_INTR 0 #define DEBUG_ISP1020_SETUP 0 #define TRACE_ISP 0 #define DEFAULT_LOOP_COUNT 1000000 #define LinuxVersionCode(v, p, s) (((v)<<16)+((p)<<8)+(s)) /* End Configuration section *************************************************/ #include #if TRACE_ISP # define TRACE_BUF_LEN (32*1024) struct { u_long next; struct { u_long time; u_int index; u_int addr; u_char * name; } buf[TRACE_BUF_LEN]; } trace; #define TRACE(w, i, a) \ { \ unsigned long flags; \ \ save_flags(flags); \ cli(); \ trace.buf[trace.next].name = (w); \ trace.buf[trace.next].time = jiffies; \ trace.buf[trace.next].index = (i); \ trace.buf[trace.next].addr = (long) (a); \ trace.next = (trace.next + 1) & (TRACE_BUF_LEN - 1); \ restore_flags(flags); \ } #else # define TRACE(w, i, a) #endif #if DEBUG_ISP1020 #define ENTER(x) printk("isp1020 : entering %s()\n", x); #define LEAVE(x) printk("isp1020 : leaving %s()\n", x); #define DEBUG(x) x #else #define ENTER(x) #define LEAVE(x) #define DEBUG(x) #endif /* DEBUG_ISP1020 */ #if DEBUG_ISP1020_INTR #define ENTER_INTR(x) printk("isp1020 : entering %s()\n", x); #define LEAVE_INTR(x) printk("isp1020 : leaving %s()\n", x); #define DEBUG_INTR(x) x #else #define ENTER_INTR(x) #define LEAVE_INTR(x) #define DEBUG_INTR(x) #endif /* DEBUG ISP1020_INTR */ #define ISP1020_REV_ID 1 #define MAX_TARGETS 16 #define MAX_LUNS 8 /* host configuration and control registers */ #define HOST_HCCR 0xc0 /* host command and control */ /* pci bus interface registers */ #define PCI_ID_LOW 0x00 /* vendor id */ #define PCI_ID_HIGH 0x02 /* device id */ #define ISP_CFG0 0x04 /* configuration register #0 */ #define ISP_CFG1 0x06 /* configuration register #1 */ #define PCI_INTF_CTL 0x08 /* pci interface control */ #define PCI_INTF_STS 0x0a /* pci interface status */ #define PCI_SEMAPHORE 0x0c /* pci semaphore */ #define PCI_NVRAM 0x0e /* pci nvram interface */ /* mailbox registers */ #define MBOX0 0x70 /* mailbox 0 */ #define MBOX1 0x72 /* mailbox 1 */ #define MBOX2 0x74 /* mailbox 2 */ #define MBOX3 0x76 /* mailbox 3 */ #define MBOX4 0x78 /* mailbox 4 */ #define MBOX5 0x7a /* mailbox 5 */ /* mailbox command complete status codes */ #define MBOX_COMMAND_COMPLETE 0x4000 #define INVALID_COMMAND 0x4001 #define HOST_INTERFACE_ERROR 0x4002 #define TEST_FAILED 0x4003 #define COMMAND_ERROR 0x4005 #define COMMAND_PARAM_ERROR 0x4006 /* async event status codes */ #define ASYNC_SCSI_BUS_RESET 0x8001 #define SYSTEM_ERROR 0x8002 #define REQUEST_TRANSFER_ERROR 0x8003 #define RESPONSE_TRANSFER_ERROR 0x8004 #define REQUEST_QUEUE_WAKEUP 0x8005 #define EXECUTION_TIMEOUT_RESET 0x8006 struct Entry_header { u_char entry_type; u_char entry_cnt; u_char sys_def_1; u_char flags; }; /* entry header type commands */ #define ENTRY_COMMAND 1 #define ENTRY_CONTINUATION 2 #define ENTRY_STATUS 3 #define ENTRY_MARKER 4 #define ENTRY_EXTENDED_COMMAND 5 /* entry header flag definitions */ #define EFLAG_CONTINUATION 1 #define EFLAG_BUSY 2 #define EFLAG_BAD_HEADER 4 #define EFLAG_BAD_PAYLOAD 8 struct dataseg { u_int d_base; u_int d_count; }; struct Command_Entry { struct Entry_header hdr; u_int handle; u_char target_lun; u_char target_id; u_short cdb_length; u_short control_flags; u_short rsvd; u_short time_out; u_short segment_cnt; u_char cdb[12]; struct dataseg dataseg[4]; }; /* command entry control flag definitions */ #define CFLAG_NODISC 0x01 #define CFLAG_HEAD_TAG 0x02 #define CFLAG_ORDERED_TAG 0x04 #define CFLAG_SIMPLE_TAG 0x08 #define CFLAG_TAR_RTN 0x10 #define CFLAG_READ 0x20 #define CFLAG_WRITE 0x40 struct Ext_Command_Entry { struct Entry_header hdr; u_int handle; u_char target_lun; u_char target_id; u_short cdb_length; u_short control_flags; u_short rsvd; u_short time_out; u_short segment_cnt; u_char cdb[44]; }; struct Continuation_Entry { struct Entry_header hdr; u_int reserved; struct dataseg dataseg[7]; }; struct Marker_Entry { struct Entry_header hdr; u_int reserved; u_char target_lun; u_char target_id; u_char modifier; u_char rsvd; u_char rsvds[52]; }; /* marker entry modifier definitions */ #define SYNC_DEVICE 0 #define SYNC_TARGET 1 #define SYNC_ALL 2 struct Status_Entry { struct Entry_header hdr; u_int handle; u_short scsi_status; u_short completion_status; u_short state_flags; u_short status_flags; u_short time; u_short req_sense_len; u_int residual; u_char rsvd[8]; u_char req_sense_data[32]; }; /* status entry completion status definitions */ #define CS_COMPLETE 0x0000 #define CS_INCOMPLETE 0x0001 #define CS_DMA_ERROR 0x0002 #define CS_TRANSPORT_ERROR 0x0003 #define CS_RESET_OCCURRED 0x0004 #define CS_ABORTED 0x0005 #define CS_TIMEOUT 0x0006 #define CS_DATA_OVERRUN 0x0007 #define CS_COMMAND_OVERRUN 0x0008 #define CS_STATUS_OVERRUN 0x0009 #define CS_BAD_MESSAGE 0x000a #define CS_NO_MESSAGE_OUT 0x000b #define CS_EXT_ID_FAILED 0x000c #define CS_IDE_MSG_FAILED 0x000d #define CS_ABORT_MSG_FAILED 0x000e #define CS_REJECT_MSG_FAILED 0x000f #define CS_NOP_MSG_FAILED 0x0010 #define CS_PARITY_ERROR_MSG_FAILED 0x0011 #define CS_DEVICE_RESET_MSG_FAILED 0x0012 #define CS_ID_MSG_FAILED 0x0013 #define CS_UNEXP_BUS_FREE 0x0014 #define CS_DATA_UNDERRUN 0x0015 /* status entry state flag definitions */ #define SF_GOT_BUS 0x0100 #define SF_GOT_TARGET 0x0200 #define SF_SENT_CDB 0x0400 #define SF_TRANSFERRED_DATA 0x0800 #define SF_GOT_STATUS 0x1000 #define SF_GOT_SENSE 0x2000 /* status entry status flag definitions */ #define STF_DISCONNECT 0x0001 #define STF_SYNCHRONOUS 0x0002 #define STF_PARITY_ERROR 0x0004 #define STF_BUS_RESET 0x0008 #define STF_DEVICE_RESET 0x0010 #define STF_ABORTED 0x0020 #define STF_TIMEOUT 0x0040 #define STF_NEGOTIATION 0x0080 /* interface control commands */ #define ISP_RESET 0x0001 #define ISP_EN_INT 0x0002 #define ISP_EN_RISC 0x0004 /* host control commands */ #define HCCR_NOP 0x0000 #define HCCR_RESET 0x1000 #define HCCR_PAUSE 0x2000 #define HCCR_RELEASE 0x3000 #define HCCR_SINGLE_STEP 0x4000 #define HCCR_SET_HOST_INTR 0x5000 #define HCCR_CLEAR_HOST_INTR 0x6000 #define HCCR_CLEAR_RISC_INTR 0x7000 #define HCCR_BP_ENABLE 0x8000 #define HCCR_BIOS_DISABLE 0x9000 #define HCCR_TEST_MODE 0xf000 #define RISC_BUSY 0x0004 /* mailbox commands */ #define MBOX_NO_OP 0x0000 #define MBOX_LOAD_RAM 0x0001 #define MBOX_EXEC_FIRMWARE 0x0002 #define MBOX_DUMP_RAM 0x0003 #define MBOX_WRITE_RAM_WORD 0x0004 #define MBOX_READ_RAM_WORD 0x0005 #define MBOX_MAILBOX_REG_TEST 0x0006 #define MBOX_VERIFY_CHECKSUM 0x0007 #define MBOX_ABOUT_FIRMWARE 0x0008 #define MBOX_CHECK_FIRMWARE 0x000e #define MBOX_INIT_REQ_QUEUE 0x0010 #define MBOX_INIT_RES_QUEUE 0x0011 #define MBOX_EXECUTE_IOCB 0x0012 #define MBOX_WAKE_UP 0x0013 #define MBOX_STOP_FIRMWARE 0x0014 #define MBOX_ABORT 0x0015 #define MBOX_ABORT_DEVICE 0x0016 #define MBOX_ABORT_TARGET 0x0017 #define MBOX_BUS_RESET 0x0018 #define MBOX_STOP_QUEUE 0x0019 #define MBOX_START_QUEUE 0x001a #define MBOX_SINGLE_STEP_QUEUE 0x001b #define MBOX_ABORT_QUEUE 0x001c #define MBOX_GET_DEV_QUEUE_STATUS 0x001d #define MBOX_GET_FIRMWARE_STATUS 0x001f #define MBOX_GET_INIT_SCSI_ID 0x0020 #define MBOX_GET_SELECT_TIMEOUT 0x0021 #define MBOX_GET_RETRY_COUNT 0x0022 #define MBOX_GET_TAG_AGE_LIMIT 0x0023 #define MBOX_GET_CLOCK_RATE 0x0024 #define MBOX_GET_ACT_NEG_STATE 0x0025 #define MBOX_GET_ASYNC_DATA_SETUP_TIME 0x0026 #define MBOX_GET_PCI_PARAMS 0x0027 #define MBOX_GET_TARGET_PARAMS 0x0028 #define MBOX_GET_DEV_QUEUE_PARAMS 0x0029 #define MBOX_SET_INIT_SCSI_ID 0x0030 #define MBOX_SET_SELECT_TIMEOUT 0x0031 #define MBOX_SET_RETRY_COUNT 0x0032 #define MBOX_SET_TAG_AGE_LIMIT 0x0033 #define MBOX_SET_CLOCK_RATE 0x0034 #define MBOX_SET_ACTIVE_NEG_STATE 0x0035 #define MBOX_SET_ASYNC_DATA_SETUP_TIME 0x0036 #define MBOX_SET_PCI_CONTROL_PARAMS 0x0037 #define MBOX_SET_TARGET_PARAMS 0x0038 #define MBOX_SET_DEV_QUEUE_PARAMS 0x0039 #define MBOX_RETURN_BIOS_BLOCK_ADDR 0x0040 #define MBOX_WRITE_FOUR_RAM_WORDS 0x0041 #define MBOX_EXEC_BIOS_IOCB 0x0042 #include "qlogicisp_asm.c" #define PACKB(a, b) (((a)<<4)|(b)) static const u_char mbox_param[] = { PACKB(1, 1), /* MBOX_NO_OP */ PACKB(5, 5), /* MBOX_LOAD_RAM */ PACKB(2, 0), /* MBOX_EXEC_FIRMWARE */ PACKB(5, 5), /* MBOX_DUMP_RAM */ PACKB(3, 3), /* MBOX_WRITE_RAM_WORD */ PACKB(2, 3), /* MBOX_READ_RAM_WORD */ PACKB(6, 6), /* MBOX_MAILBOX_REG_TEST */ PACKB(2, 3), /* MBOX_VERIFY_CHECKSUM */ PACKB(1, 3), /* MBOX_ABOUT_FIRMWARE */ PACKB(0, 0), /* 0x0009 */ PACKB(0, 0), /* 0x000a */ PACKB(0, 0), /* 0x000b */ PACKB(0, 0), /* 0x000c */ PACKB(0, 0), /* 0x000d */ PACKB(1, 2), /* MBOX_CHECK_FIRMWARE */ PACKB(0, 0), /* 0x000f */ PACKB(5, 5), /* MBOX_INIT_REQ_QUEUE */ PACKB(6, 6), /* MBOX_INIT_RES_QUEUE */ PACKB(4, 4), /* MBOX_EXECUTE_IOCB */ PACKB(2, 2), /* MBOX_WAKE_UP */ PACKB(1, 6), /* MBOX_STOP_FIRMWARE */ PACKB(4, 4), /* MBOX_ABORT */ PACKB(2, 2), /* MBOX_ABORT_DEVICE */ PACKB(3, 3), /* MBOX_ABORT_TARGET */ PACKB(2, 2), /* MBOX_BUS_RESET */ PACKB(2, 3), /* MBOX_STOP_QUEUE */ PACKB(2, 3), /* MBOX_START_QUEUE */ PACKB(2, 3), /* MBOX_SINGLE_STEP_QUEUE */ PACKB(2, 3), /* MBOX_ABORT_QUEUE */ PACKB(2, 4), /* MBOX_GET_DEV_QUEUE_STATUS */ PACKB(0, 0), /* 0x001e */ PACKB(1, 3), /* MBOX_GET_FIRMWARE_STATUS */ PACKB(1, 2), /* MBOX_GET_INIT_SCSI_ID */ PACKB(1, 2), /* MBOX_GET_SELECT_TIMEOUT */ PACKB(1, 3), /* MBOX_GET_RETRY_COUNT */ PACKB(1, 2), /* MBOX_GET_TAG_AGE_LIMIT */ PACKB(1, 2), /* MBOX_GET_CLOCK_RATE */ PACKB(1, 2), /* MBOX_GET_ACT_NEG_STATE */ PACKB(1, 2), /* MBOX_GET_ASYNC_DATA_SETUP_TIME */ PACKB(1, 3), /* MBOX_GET_PCI_PARAMS */ PACKB(2, 4), /* MBOX_GET_TARGET_PARAMS */ PACKB(2, 4), /* MBOX_GET_DEV_QUEUE_PARAMS */ PACKB(0, 0), /* 0x002a */ PACKB(0, 0), /* 0x002b */ PACKB(0, 0), /* 0x002c */ PACKB(0, 0), /* 0x002d */ PACKB(0, 0), /* 0x002e */ PACKB(0, 0), /* 0x002f */ PACKB(2, 2), /* MBOX_SET_INIT_SCSI_ID */ PACKB(2, 2), /* MBOX_SET_SELECT_TIMEOUT */ PACKB(3, 3), /* MBOX_SET_RETRY_COUNT */ PACKB(2, 2), /* MBOX_SET_TAG_AGE_LIMIT */ PACKB(2, 2), /* MBOX_SET_CLOCK_RATE */ PACKB(2, 2), /* MBOX_SET_ACTIVE_NEG_STATE */ PACKB(2, 2), /* MBOX_SET_ASYNC_DATA_SETUP_TIME */ PACKB(3, 3), /* MBOX_SET_PCI_CONTROL_PARAMS */ PACKB(4, 4), /* MBOX_SET_TARGET_PARAMS */ PACKB(4, 4), /* MBOX_SET_DEV_QUEUE_PARAMS */ PACKB(0, 0), /* 0x003a */ PACKB(0, 0), /* 0x003b */ PACKB(0, 0), /* 0x003c */ PACKB(0, 0), /* 0x003d */ PACKB(0, 0), /* 0x003e */ PACKB(0, 0), /* 0x003f */ PACKB(1, 2), /* MBOX_RETURN_BIOS_BLOCK_ADDR */ PACKB(6, 1), /* MBOX_WRITE_FOUR_RAM_WORDS */ PACKB(2, 3) /* MBOX_EXEC_BIOS_IOCB */ }; #define MAX_MBOX_COMMAND (sizeof(mbox_param)/sizeof(u_short)) struct host_param { u_short fifo_threshold; u_short host_adapter_enable; u_short initiator_scsi_id; u_short bus_reset_delay; u_short retry_count; u_short retry_delay; u_short async_data_setup_time; u_short req_ack_active_negation; u_short data_line_active_negation; u_short data_dma_burst_enable; u_short command_dma_burst_enable; u_short tag_aging; u_short selection_timeout; u_short max_queue_depth; }; /* * Device Flags: * * Bit Name * --------- * 7 Disconnect Privilege * 6 Parity Checking * 5 Wide Data Transfers * 4 Synchronous Data Transfers * 3 Tagged Queuing * 2 Automatic Request Sense * 1 Stop Queue on Check Condition * 0 Renegotiate on Error */ struct dev_param { u_short device_flags; u_short execution_throttle; u_short synchronous_period; u_short synchronous_offset; u_short device_enable; u_short reserved; /* pad */ }; /* * The result queue can be quite a bit smaller since continuation entries * do not show up there: */ #define RES_QUEUE_LEN ((QLOGICISP_REQ_QUEUE_LEN + 1) / 8 - 1) #define QUEUE_ENTRY_LEN 64 struct isp1020_hostdata { u_char revision; struct host_param host_param; struct dev_param dev_param[MAX_TARGETS]; struct pci_dev *pci_dev; /* result and request queues (shared with isp1020): */ u_int req_in_ptr; /* index of next request slot */ u_int res_out_ptr; /* index of next result slot */ /* this is here so the queues are nicely aligned */ long send_marker; /* do we need to send a marker? */ char res[RES_QUEUE_LEN+1][QUEUE_ENTRY_LEN]; char req[QLOGICISP_REQ_QUEUE_LEN+1][QUEUE_ENTRY_LEN]; }; /* queue length's _must_ be power of two: */ #define QUEUE_DEPTH(in, out, ql) ((in - out) & (ql)) #define REQ_QUEUE_DEPTH(in, out) QUEUE_DEPTH(in, out, \ QLOGICISP_REQ_QUEUE_LEN) #define RES_QUEUE_DEPTH(in, out) QUEUE_DEPTH(in, out, RES_QUEUE_LEN) static void isp1020_enable_irqs(struct Scsi_Host *); static void isp1020_disable_irqs(struct Scsi_Host *); static int isp1020_init(struct Scsi_Host *); static int isp1020_reset_hardware(struct Scsi_Host *); static int isp1020_set_defaults(struct Scsi_Host *); static int isp1020_load_parameters(struct Scsi_Host *); static int isp1020_mbox_command(struct Scsi_Host *, u_short []); static int isp1020_return_status(struct Status_Entry *); static void isp1020_intr_handler(int, void *, struct pt_regs *); static void do_isp1020_intr_handler(int, void *, struct pt_regs *); #if USE_NVRAM_DEFAULTS static int isp1020_get_defaults(struct Scsi_Host *); static int isp1020_verify_nvram(struct Scsi_Host *); static u_short isp1020_read_nvram_word(struct Scsi_Host *, u_short); #endif #if DEBUG_ISP1020 static void isp1020_print_scsi_cmd(Scsi_Cmnd *); #endif #if DEBUG_ISP1020_INTR static void isp1020_print_status_entry(struct Status_Entry *); #endif static struct proc_dir_entry proc_scsi_isp1020 = { PROC_SCSI_QLOGICISP, 7, "isp1020", S_IFDIR | S_IRUGO | S_IXUGO, 2 }; static inline void isp1020_enable_irqs(struct Scsi_Host *host) { outw(ISP_EN_INT|ISP_EN_RISC, host->io_port + PCI_INTF_CTL); } static inline void isp1020_disable_irqs(struct Scsi_Host *host) { outw(0x0, host->io_port + PCI_INTF_CTL); } int isp1020_detect(Scsi_Host_Template *tmpt) { int hosts = 0; struct Scsi_Host *host; struct isp1020_hostdata *hostdata; struct pci_dev *pdev = NULL; ENTER("isp1020_detect"); tmpt->proc_dir = &proc_scsi_isp1020; if (pci_present() == 0) { printk("qlogicisp : PCI not present\n"); return 0; } while ((pdev = pci_find_device(PCI_VENDOR_ID_QLOGIC, PCI_DEVICE_ID_QLOGIC_ISP1020, pdev))) { host = scsi_register(tmpt, sizeof(struct isp1020_hostdata)); hostdata = (struct isp1020_hostdata *) host->hostdata; memset(hostdata, 0, sizeof(struct isp1020_hostdata)); hostdata->pci_dev = pdev; if (isp1020_init(host) || isp1020_reset_hardware(host) #if USE_NVRAM_DEFAULTS || isp1020_get_defaults(host) #else || isp1020_set_defaults(host) #endif /* USE_NVRAM_DEFAULTS */ || isp1020_load_parameters(host)) { scsi_unregister(host); continue; } host->this_id = hostdata->host_param.initiator_scsi_id; if (request_irq(host->irq, do_isp1020_intr_handler, SA_INTERRUPT | SA_SHIRQ, "qlogicisp", host)) { printk("qlogicisp : interrupt %d already in use\n", host->irq); scsi_unregister(host); continue; } if (check_region(host->io_port, 0xff)) { printk("qlogicisp : i/o region 0x%lx-0x%lx already " "in use\n", host->io_port, host->io_port + 0xff); free_irq(host->irq, host); scsi_unregister(host); continue; } request_region(host->io_port, 0xff, "qlogicisp"); outw(0x0, host->io_port + PCI_SEMAPHORE); outw(HCCR_CLEAR_RISC_INTR, host->io_port + HOST_HCCR); isp1020_enable_irqs(host); hosts++; } LEAVE("isp1020_detect"); return hosts; } int isp1020_release(struct Scsi_Host *host) { struct isp1020_hostdata *hostdata; ENTER("isp1020_release"); hostdata = (struct isp1020_hostdata *) host->hostdata; outw(0x0, host->io_port + PCI_INTF_CTL); free_irq(host->irq, host); release_region(host->io_port, 0xff); LEAVE("isp1020_release"); return 0; } const char *isp1020_info(struct Scsi_Host *host) { static char buf[80]; struct isp1020_hostdata *hostdata; ENTER("isp1020_info"); hostdata = (struct isp1020_hostdata *) host->hostdata; sprintf(buf, "QLogic ISP1020 SCSI on PCI bus %02x device %02x irq %d base 0x%lx", hostdata->pci_dev->bus->number, hostdata->pci_dev->devfn, host->irq, host->io_port); LEAVE("isp1020_info"); return buf; } /* * The middle SCSI layer ensures that queuecommand never gets invoked * concurrently with itself or the interrupt handler (though the * interrupt handler may call this routine as part of * request-completion handling). */ int isp1020_queuecommand(Scsi_Cmnd *Cmnd, void (*done)(Scsi_Cmnd *)) { int i, sg_count, n, num_free; u_int in_ptr, out_ptr; struct dataseg * ds; struct scatterlist *sg; struct Command_Entry *cmd; struct Continuation_Entry *cont; struct Scsi_Host *host; struct isp1020_hostdata *hostdata; ENTER("isp1020_queuecommand"); host = Cmnd->host; hostdata = (struct isp1020_hostdata *) host->hostdata; Cmnd->scsi_done = done; DEBUG(isp1020_print_scsi_cmd(Cmnd)); out_ptr = inw(host->io_port + MBOX4); in_ptr = hostdata->req_in_ptr; DEBUG(printk("qlogicisp : request queue depth %d\n", REQ_QUEUE_DEPTH(in_ptr, out_ptr))); cmd = (struct Command_Entry *) &hostdata->req[in_ptr][0]; in_ptr = (in_ptr + 1) & QLOGICISP_REQ_QUEUE_LEN; if (in_ptr == out_ptr) { printk("qlogicisp : request queue overflow\n"); return 1; } if (hostdata->send_marker) { struct Marker_Entry *marker; TRACE("queue marker", in_ptr, 0); DEBUG(printk("qlogicisp : adding marker entry\n")); marker = (struct Marker_Entry *) cmd; memset(marker, 0, sizeof(struct Marker_Entry)); marker->hdr.entry_type = ENTRY_MARKER; marker->hdr.entry_cnt = 1; marker->modifier = SYNC_ALL; hostdata->send_marker = 0; if (((in_ptr + 1) & QLOGICISP_REQ_QUEUE_LEN) == out_ptr) { outw(in_ptr, host->io_port + MBOX4); hostdata->req_in_ptr = in_ptr; printk("qlogicisp : request queue overflow\n"); return 1; } cmd = (struct Command_Entry *) &hostdata->req[in_ptr][0]; in_ptr = (in_ptr + 1) & QLOGICISP_REQ_QUEUE_LEN; } TRACE("queue command", in_ptr, Cmnd); memset(cmd, 0, sizeof(struct Command_Entry)); cmd->hdr.entry_type = ENTRY_COMMAND; cmd->hdr.entry_cnt = 1; cmd->handle = cpu_to_le32((u_int) virt_to_bus(Cmnd)); cmd->target_lun = Cmnd->lun; cmd->target_id = Cmnd->target; cmd->cdb_length = cpu_to_le16(Cmnd->cmd_len); cmd->control_flags = cpu_to_le16(CFLAG_READ | CFLAG_WRITE); cmd->time_out = cpu_to_le16(30); memcpy(cmd->cdb, Cmnd->cmnd, Cmnd->cmd_len); if (Cmnd->use_sg) { cmd->segment_cnt = cpu_to_le16(sg_count = Cmnd->use_sg); sg = (struct scatterlist *) Cmnd->request_buffer; ds = cmd->dataseg; /* fill in first four sg entries: */ n = sg_count; if (n > 4) n = 4; for (i = 0; i < n; i++) { ds[i].d_base = cpu_to_le32((u_int) virt_to_bus(sg->address)); ds[i].d_count = cpu_to_le32(sg->length); ++sg; } sg_count -= 4; while (sg_count > 0) { ++cmd->hdr.entry_cnt; cont = (struct Continuation_Entry *) &hostdata->req[in_ptr][0]; in_ptr = (in_ptr + 1) & QLOGICISP_REQ_QUEUE_LEN; if (in_ptr == out_ptr) { printk("isp1020: unexpected request queue " "overflow\n"); return 1; } TRACE("queue continuation", in_ptr, 0); cont->hdr.entry_type = ENTRY_CONTINUATION; cont->hdr.entry_cnt = 0; cont->hdr.sys_def_1 = 0; cont->hdr.flags = 0; cont->reserved = 0; ds = cont->dataseg; n = sg_count; if (n > 7) n = 7; for (i = 0; i < n; ++i) { ds[i].d_base = cpu_to_le32((u_int)virt_to_bus(sg->address)); ds[i].d_count = cpu_to_le32(sg->length); ++sg; } sg_count -= n; } } else { cmd->dataseg[0].d_base = cpu_to_le32((u_int) virt_to_bus(Cmnd->request_buffer)); cmd->dataseg[0].d_count = cpu_to_le32((u_int) Cmnd->request_bufflen); cmd->segment_cnt = cpu_to_le16(1); } outw(in_ptr, host->io_port + MBOX4); hostdata->req_in_ptr = in_ptr; num_free = QLOGICISP_REQ_QUEUE_LEN - REQ_QUEUE_DEPTH(in_ptr, out_ptr); host->can_queue = host->host_busy + num_free; host->sg_tablesize = QLOGICISP_MAX_SG(num_free); LEAVE("isp1020_queuecommand"); return 0; } #define ASYNC_EVENT_INTERRUPT 0x01 void do_isp1020_intr_handler(int irq, void *dev_id, struct pt_regs *regs) { unsigned long flags; spin_lock_irqsave(&io_request_lock, flags); isp1020_intr_handler(irq, dev_id, regs); spin_unlock_irqrestore(&io_request_lock, flags); } void isp1020_intr_handler(int irq, void *dev_id, struct pt_regs *regs) { Scsi_Cmnd *Cmnd; struct Status_Entry *sts; struct Scsi_Host *host = dev_id; struct isp1020_hostdata *hostdata; u_int in_ptr, out_ptr; u_short status; ENTER_INTR("isp1020_intr_handler"); hostdata = (struct isp1020_hostdata *) host->hostdata; DEBUG_INTR(printk("qlogicisp : interrupt on line %d\n", irq)); if (!(inw(host->io_port + PCI_INTF_STS) & 0x04)) { /* spurious interrupts can happen legally */ DEBUG_INTR(printk("qlogicisp: got spurious interrupt\n")); return; } in_ptr = inw(host->io_port + MBOX5); outw(HCCR_CLEAR_RISC_INTR, host->io_port + HOST_HCCR); if ((inw(host->io_port + PCI_SEMAPHORE) & ASYNC_EVENT_INTERRUPT)) { status = inw(host->io_port + MBOX0); DEBUG_INTR(printk("qlogicisp : mbox completion status: %x\n", status)); switch (status) { case ASYNC_SCSI_BUS_RESET: case EXECUTION_TIMEOUT_RESET: hostdata->send_marker = 1; break; case INVALID_COMMAND: case HOST_INTERFACE_ERROR: case COMMAND_ERROR: case COMMAND_PARAM_ERROR: printk("qlogicisp : bad mailbox return status\n"); break; } outw(0x0, host->io_port + PCI_SEMAPHORE); } out_ptr = hostdata->res_out_ptr; DEBUG_INTR(printk("qlogicisp : response queue update\n")); DEBUG_INTR(printk("qlogicisp : response queue depth %d\n", QUEUE_DEPTH(in_ptr, out_ptr, RES_QUEUE_LEN))); while (out_ptr != in_ptr) { sts = (struct Status_Entry *) &hostdata->res[out_ptr][0]; out_ptr = (out_ptr + 1) & RES_QUEUE_LEN; Cmnd = (Scsi_Cmnd *) bus_to_virt(le32_to_cpu(sts->handle)); TRACE("done", out_ptr, Cmnd); if (le16_to_cpu(sts->completion_status) == CS_RESET_OCCURRED || le16_to_cpu(sts->completion_status) == CS_ABORTED || (le16_to_cpu(sts->status_flags) & STF_BUS_RESET)) hostdata->send_marker = 1; if (le16_to_cpu(sts->state_flags) & SF_GOT_SENSE) memcpy(Cmnd->sense_buffer, sts->req_sense_data, sizeof(Cmnd->sense_buffer)); DEBUG_INTR(isp1020_print_status_entry(sts)); if (sts->hdr.entry_type == ENTRY_STATUS) Cmnd->result = isp1020_return_status(sts); else Cmnd->result = DID_ERROR << 16; outw(out_ptr, host->io_port + MBOX5); (*Cmnd->scsi_done)(Cmnd); } hostdata->res_out_ptr = out_ptr; LEAVE_INTR("isp1020_intr_handler"); } static int isp1020_return_status(struct Status_Entry *sts) { int host_status = DID_ERROR; #if DEBUG_ISP1020_INTR static char *reason[] = { "DID_OK", "DID_NO_CONNECT", "DID_BUS_BUSY", "DID_TIME_OUT", "DID_BAD_TARGET", "DID_ABORT", "DID_PARITY", "DID_ERROR", "DID_RESET", "DID_BAD_INTR" }; #endif /* DEBUG_ISP1020_INTR */ ENTER("isp1020_return_status"); DEBUG(printk("qlogicisp : completion status = 0x%04x\n", le16_to_cpu(sts->completion_status))); switch(le16_to_cpu(sts->completion_status)) { case CS_COMPLETE: host_status = DID_OK; break; case CS_INCOMPLETE: if (!(le16_to_cpu(sts->state_flags) & SF_GOT_BUS)) host_status = DID_NO_CONNECT; else if (!(le16_to_cpu(sts->state_flags) & SF_GOT_TARGET)) host_status = DID_BAD_TARGET; else if (!(le16_to_cpu(sts->state_flags) & SF_SENT_CDB)) host_status = DID_ERROR; else if (!(le16_to_cpu(sts->state_flags) & SF_TRANSFERRED_DATA)) host_status = DID_ERROR; else if (!(le16_to_cpu(sts->state_flags) & SF_GOT_STATUS)) host_status = DID_ERROR; else if (!(le16_to_cpu(sts->state_flags) & SF_GOT_SENSE)) host_status = DID_ERROR; break; case CS_DMA_ERROR: case CS_TRANSPORT_ERROR: host_status = DID_ERROR; break; case CS_RESET_OCCURRED: host_status = DID_RESET; break; case CS_ABORTED: host_status = DID_ABORT; break; case CS_TIMEOUT: host_status = DID_TIME_OUT; break; case CS_DATA_OVERRUN: case CS_COMMAND_OVERRUN: case CS_STATUS_OVERRUN: case CS_BAD_MESSAGE: case CS_NO_MESSAGE_OUT: case CS_EXT_ID_FAILED: case CS_IDE_MSG_FAILED: case CS_ABORT_MSG_FAILED: case CS_NOP_MSG_FAILED: case CS_PARITY_ERROR_MSG_FAILED: case CS_DEVICE_RESET_MSG_FAILED: case CS_ID_MSG_FAILED: case CS_UNEXP_BUS_FREE: host_status = DID_ERROR; break; case CS_DATA_UNDERRUN: host_status = DID_OK; break; default: printk("qlogicisp : unknown completion status 0x%04x\n", le16_to_cpu(sts->completion_status)); host_status = DID_ERROR; break; } DEBUG_INTR(printk("qlogicisp : host status (%s) scsi status %x\n", reason[host_status], le16_to_cpu(sts->scsi_status))); LEAVE("isp1020_return_status"); return (le16_to_cpu(sts->scsi_status) & STATUS_MASK) | (host_status << 16); } int isp1020_abort(Scsi_Cmnd *Cmnd) { u_short param[6]; struct Scsi_Host *host; struct isp1020_hostdata *hostdata; int return_status = SCSI_ABORT_SUCCESS; u_int cmdaddr = virt_to_bus(Cmnd); ENTER("isp1020_abort"); host = Cmnd->host; hostdata = (struct isp1020_hostdata *) host->hostdata; isp1020_disable_irqs(host); param[0] = MBOX_ABORT; param[1] = (((u_short) Cmnd->target) << 8) | Cmnd->lun; param[2] = cmdaddr >> 16; param[3] = cmdaddr & 0xffff; isp1020_mbox_command(host, param); if (param[0] != MBOX_COMMAND_COMPLETE) { printk("qlogicisp : scsi abort failure: %x\n", param[0]); return_status = SCSI_ABORT_ERROR; } isp1020_enable_irqs(host); LEAVE("isp1020_abort"); return return_status; } int isp1020_reset(Scsi_Cmnd *Cmnd, unsigned int reset_flags) { u_short param[6]; struct Scsi_Host *host; struct isp1020_hostdata *hostdata; int return_status = SCSI_RESET_SUCCESS; ENTER("isp1020_reset"); host = Cmnd->host; hostdata = (struct isp1020_hostdata *) host->hostdata; param[0] = MBOX_BUS_RESET; param[1] = hostdata->host_param.bus_reset_delay; isp1020_disable_irqs(host); isp1020_mbox_command(host, param); if (param[0] != MBOX_COMMAND_COMPLETE) { printk("qlogicisp : scsi bus reset failure: %x\n", param[0]); return_status = SCSI_RESET_ERROR; } isp1020_enable_irqs(host); LEAVE("isp1020_reset"); return return_status;; } int isp1020_biosparam(Disk *disk, kdev_t n, int ip[]) { int size = disk->capacity; ENTER("isp1020_biosparam"); ip[0] = 64; ip[1] = 32; ip[2] = size >> 11; if (ip[2] > 1024) { ip[0] = 255; ip[1] = 63; ip[2] = size / (ip[0] * ip[1]); #if 0 if (ip[2] > 1023) ip[2] = 1023; #endif } LEAVE("isp1020_biosparam"); return 0; } static int isp1020_reset_hardware(struct Scsi_Host *host) { u_short param[6]; int loop_count; ENTER("isp1020_reset_hardware"); outw(ISP_RESET, host->io_port + PCI_INTF_CTL); udelay(100); outw(HCCR_RESET, host->io_port + HOST_HCCR); udelay(100); outw(HCCR_RELEASE, host->io_port + HOST_HCCR); outw(HCCR_BIOS_DISABLE, host->io_port + HOST_HCCR); loop_count = DEFAULT_LOOP_COUNT; while (--loop_count && inw(host->io_port + HOST_HCCR) == RISC_BUSY) barrier(); if (!loop_count) printk("qlogicisp: reset_hardware loop timeout\n"); outw(0, host->io_port + ISP_CFG1); #if DEBUG_ISP1020 printk("qlogicisp : mbox 0 0x%04x \n", inw(host->io_port + MBOX0)); printk("qlogicisp : mbox 1 0x%04x \n", inw(host->io_port + MBOX1)); printk("qlogicisp : mbox 2 0x%04x \n", inw(host->io_port + MBOX2)); printk("qlogicisp : mbox 3 0x%04x \n", inw(host->io_port + MBOX3)); printk("qlogicisp : mbox 4 0x%04x \n", inw(host->io_port + MBOX4)); printk("qlogicisp : mbox 5 0x%04x \n", inw(host->io_port + MBOX5)); #endif /* DEBUG_ISP1020 */ param[0] = MBOX_NO_OP; isp1020_mbox_command(host, param); if (param[0] != MBOX_COMMAND_COMPLETE) { printk("qlogicisp : NOP test failed\n"); return 1; } DEBUG(printk("qlogicisp : loading risc ram\n")); #if RELOAD_FIRMWARE for (loop_count = 0; loop_count < risc_code_length01; loop_count++) { param[0] = MBOX_WRITE_RAM_WORD; param[1] = risc_code_addr01 + loop_count; param[2] = risc_code01[loop_count]; isp1020_mbox_command(host, param); if (param[0] != MBOX_COMMAND_COMPLETE) { printk("qlogicisp : firmware load failure at %d\n", loop_count); return 1; } } #endif /* RELOAD_FIRMWARE */ DEBUG(printk("qlogicisp : verifying checksum\n")); param[0] = MBOX_VERIFY_CHECKSUM; param[1] = risc_code_addr01; isp1020_mbox_command(host, param); if (param[0] != MBOX_COMMAND_COMPLETE) { printk("qlogicisp : ram checksum failure\n"); return 1; } DEBUG(printk("qlogicisp : executing firmware\n")); param[0] = MBOX_EXEC_FIRMWARE; param[1] = risc_code_addr01; isp1020_mbox_command(host, param); param[0] = MBOX_ABOUT_FIRMWARE; isp1020_mbox_command(host, param); if (param[0] != MBOX_COMMAND_COMPLETE) { printk("qlogicisp : about firmware failure\n"); return 1; } DEBUG(printk("qlogicisp : firmware major revision %d\n", param[1])); DEBUG(printk("qlogicisp : firmware minor revision %d\n", param[2])); LEAVE("isp1020_reset_hardware"); return 0; } static int isp1020_init(struct Scsi_Host *sh) { u_long io_base, io_flags; struct isp1020_hostdata *hostdata; u_char revision; u_int irq; u_short command; struct pci_dev *pdev; ENTER("isp1020_init"); hostdata = (struct isp1020_hostdata *) sh->hostdata; pdev = hostdata->pci_dev; if (pci_read_config_word(pdev, PCI_COMMAND, &command) || pci_read_config_byte(pdev, PCI_CLASS_REVISION, &revision)) { printk("qlogicisp : error reading PCI configuration\n"); return 1; } io_base = pdev->resource[0].start; io_flags = pdev->resource[0].flags; irq = pdev->irq; if (pdev->vendor != PCI_VENDOR_ID_QLOGIC) { printk("qlogicisp : 0x%04x is not QLogic vendor ID\n", pdev->vendor); return 1; } if (pdev->device != PCI_DEVICE_ID_QLOGIC_ISP1020) { printk("qlogicisp : 0x%04x does not match ISP1020 device id\n", pdev->device); return 1; } #ifdef __sparc__ command |= (PCI_COMMAND_MASTER|PCI_COMMAND_IO|PCI_COMMAND_MEMORY| PCI_COMMAND_INVALIDATE|PCI_COMMAND_SERR); pci_write_config_word(pdev, PCI_COMMAND, command); pci_read_config_word(pdev, PCI_COMMAND, &command); pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, 16); pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 64); #endif if (! ((command & PCI_COMMAND_IO) && ((io_flags & PCI_BASE_ADDRESS_SPACE) == PCI_BASE_ADDRESS_SPACE_IO))) { printk("qlogicisp : i/o mapping is disabled\n"); return 1; } if (!(command & PCI_COMMAND_MASTER)) { printk("qlogicisp : bus mastering is disabled\n"); return 1; } if (revision != ISP1020_REV_ID) printk("qlogicisp : new isp1020 revision ID (%d)\n", revision); if (inw(io_base + PCI_ID_LOW) != PCI_VENDOR_ID_QLOGIC || inw(io_base + PCI_ID_HIGH) != PCI_DEVICE_ID_QLOGIC_ISP1020) { printk("qlogicisp : can't decode i/o address space 0x%lx\n", io_base); return 1; } hostdata->revision = revision; sh->irq = irq; sh->io_port = io_base; sh->max_id = MAX_TARGETS; sh->max_lun = MAX_LUNS; LEAVE("isp1020_init"); return 0; } #if USE_NVRAM_DEFAULTS static int isp1020_get_defaults(struct Scsi_Host *host) { int i; u_short value; struct isp1020_hostdata *hostdata = (struct isp1020_hostdata *) host->hostdata; ENTER("isp1020_get_defaults"); if (!isp1020_verify_nvram(host)) { printk("qlogicisp : nvram checksum failure\n"); printk("qlogicisp : attempting to use default parameters\n"); return isp1020_set_defaults(host); } value = isp1020_read_nvram_word(host, 2); hostdata->host_param.fifo_threshold = (value >> 8) & 0x03; hostdata->host_param.host_adapter_enable = (value >> 11) & 0x01; hostdata->host_param.initiator_scsi_id = (value >> 12) & 0x0f; value = isp1020_read_nvram_word(host, 3); hostdata->host_param.bus_reset_delay = value & 0xff; hostdata->host_param.retry_count = value >> 8; value = isp1020_read_nvram_word(host, 4); hostdata->host_param.retry_delay = value & 0xff; hostdata->host_param.async_data_setup_time = (value >> 8) & 0x0f; hostdata->host_param.req_ack_active_negation = (value >> 12) & 0x01; hostdata->host_param.data_line_active_negation = (value >> 13) & 0x01; hostdata->host_param.data_dma_burst_enable = (value >> 14) & 0x01; hostdata->host_param.command_dma_burst_enable = (value >> 15); value = isp1020_read_nvram_word(host, 5); hostdata->host_param.tag_aging = value & 0xff; value = isp1020_read_nvram_word(host, 6); hostdata->host_param.selection_timeout = value & 0xffff; value = isp1020_read_nvram_word(host, 7); hostdata->host_param.max_queue_depth = value & 0xffff; #if DEBUG_ISP1020_SETUP printk("qlogicisp : fifo threshold=%d\n", hostdata->host_param.fifo_threshold); printk("qlogicisp : initiator scsi id=%d\n", hostdata->host_param.initiator_scsi_id); printk("qlogicisp : bus reset delay=%d\n", hostdata->host_param.bus_reset_delay); printk("qlogicisp : retry count=%d\n", hostdata->host_param.retry_count); printk("qlogicisp : retry delay=%d\n", hostdata->host_param.retry_delay); printk("qlogicisp : async data setup time=%d\n", hostdata->host_param.async_data_setup_time); printk("qlogicisp : req/ack active negation=%d\n", hostdata->host_param.req_ack_active_negation); printk("qlogicisp : data line active negation=%d\n", hostdata->host_param.data_line_active_negation); printk("qlogicisp : data DMA burst enable=%d\n", hostdata->host_param.data_dma_burst_enable); printk("qlogicisp : command DMA burst enable=%d\n", hostdata->host_param.command_dma_burst_enable); printk("qlogicisp : tag age limit=%d\n", hostdata->host_param.tag_aging); printk("qlogicisp : selection timeout limit=%d\n", hostdata->host_param.selection_timeout); printk("qlogicisp : max queue depth=%d\n", hostdata->host_param.max_queue_depth); #endif /* DEBUG_ISP1020_SETUP */ for (i = 0; i < MAX_TARGETS; i++) { value = isp1020_read_nvram_word(host, 14 + i * 3); hostdata->dev_param[i].device_flags = value & 0xff; hostdata->dev_param[i].execution_throttle = value >> 8; value = isp1020_read_nvram_word(host, 15 + i * 3); hostdata->dev_param[i].synchronous_period = value & 0xff; hostdata->dev_param[i].synchronous_offset = (value >> 8) & 0x0f; hostdata->dev_param[i].device_enable = (value >> 12) & 0x01; #if DEBUG_ISP1020_SETUP printk("qlogicisp : target 0x%02x\n", i); printk("qlogicisp : device flags=0x%02x\n", hostdata->dev_param[i].device_flags); printk("qlogicisp : execution throttle=%d\n", hostdata->dev_param[i].execution_throttle); printk("qlogicisp : synchronous period=%d\n", hostdata->dev_param[i].synchronous_period); printk("qlogicisp : synchronous offset=%d\n", hostdata->dev_param[i].synchronous_offset); printk("qlogicisp : device enable=%d\n", hostdata->dev_param[i].device_enable); #endif /* DEBUG_ISP1020_SETUP */ } LEAVE("isp1020_get_defaults"); return 0; } #define ISP1020_NVRAM_LEN 0x40 #define ISP1020_NVRAM_SIG1 0x5349 #define ISP1020_NVRAM_SIG2 0x2050 static int isp1020_verify_nvram(struct Scsi_Host *host) { int i; u_short value; u_char checksum = 0; for (i = 0; i < ISP1020_NVRAM_LEN; i++) { value = isp1020_read_nvram_word(host, i); switch (i) { case 0: if (value != ISP1020_NVRAM_SIG1) return 0; break; case 1: if (value != ISP1020_NVRAM_SIG2) return 0; break; case 2: if ((value & 0xff) != 0x02) return 0; break; } checksum += value & 0xff; checksum += value >> 8; } return (checksum == 0); } #define NVRAM_DELAY() udelay(2) /* 2 microsecond delay */ u_short isp1020_read_nvram_word(struct Scsi_Host *host, u_short byte) { int i; u_short value, output, input; byte &= 0x3f; byte |= 0x0180; for (i = 8; i >= 0; i--) { output = ((byte >> i) & 0x1) ? 0x4 : 0x0; outw(output | 0x2, host->io_port + PCI_NVRAM); NVRAM_DELAY(); outw(output | 0x3, host->io_port + PCI_NVRAM); NVRAM_DELAY(); outw(output | 0x2, host->io_port + PCI_NVRAM); NVRAM_DELAY(); } for (i = 0xf, value = 0; i >= 0; i--) { value <<= 1; outw(0x3, host->io_port + PCI_NVRAM); NVRAM_DELAY(); input = inw(host->io_port + PCI_NVRAM); NVRAM_DELAY(); outw(0x2, host->io_port + PCI_NVRAM); NVRAM_DELAY(); if (input & 0x8) value |= 1; } outw(0x0, host->io_port + PCI_NVRAM); NVRAM_DELAY(); return value; } #endif /* USE_NVRAM_DEFAULTS */ static int isp1020_set_defaults(struct Scsi_Host *host) { struct isp1020_hostdata *hostdata = (struct isp1020_hostdata *) host->hostdata; int i; ENTER("isp1020_set_defaults"); hostdata->host_param.fifo_threshold = 2; hostdata->host_param.host_adapter_enable = 1; hostdata->host_param.initiator_scsi_id = 7; hostdata->host_param.bus_reset_delay = 3; hostdata->host_param.retry_count = 0; hostdata->host_param.retry_delay = 1; hostdata->host_param.async_data_setup_time = 6; hostdata->host_param.req_ack_active_negation = 1; hostdata->host_param.data_line_active_negation = 1; hostdata->host_param.data_dma_burst_enable = 1; hostdata->host_param.command_dma_burst_enable = 1; hostdata->host_param.tag_aging = 8; hostdata->host_param.selection_timeout = 250; hostdata->host_param.max_queue_depth = 256; for (i = 0; i < MAX_TARGETS; i++) { hostdata->dev_param[i].device_flags = 0xfd; hostdata->dev_param[i].execution_throttle = 16; hostdata->dev_param[i].synchronous_period = 25; hostdata->dev_param[i].synchronous_offset = 12; hostdata->dev_param[i].device_enable = 1; } LEAVE("isp1020_set_defaults"); return 0; } static int isp1020_load_parameters(struct Scsi_Host *host) { int i, k; u_int queue_addr; u_short param[6]; u_short isp_cfg1; unsigned long flags; struct isp1020_hostdata *hostdata = (struct isp1020_hostdata *) host->hostdata; ENTER("isp1020_load_parameters"); save_flags(flags); cli(); outw(hostdata->host_param.fifo_threshold, host->io_port + ISP_CFG1); param[0] = MBOX_SET_INIT_SCSI_ID; param[1] = hostdata->host_param.initiator_scsi_id; isp1020_mbox_command(host, param); if (param[0] != MBOX_COMMAND_COMPLETE) { restore_flags(flags); printk("qlogicisp : set initiator id failure\n"); return 1; } param[0] = MBOX_SET_RETRY_COUNT; param[1] = hostdata->host_param.retry_count; param[2] = hostdata->host_param.retry_delay; isp1020_mbox_command(host, param); if (param[0] != MBOX_COMMAND_COMPLETE) { restore_flags(flags); printk("qlogicisp : set retry count failure\n"); return 1; } param[0] = MBOX_SET_ASYNC_DATA_SETUP_TIME; param[1] = hostdata->host_param.async_data_setup_time; isp1020_mbox_command(host, param); if (param[0] != MBOX_COMMAND_COMPLETE) { restore_flags(flags); printk("qlogicisp : async data setup time failure\n"); return 1; } param[0] = MBOX_SET_ACTIVE_NEG_STATE; param[1] = (hostdata->host_param.req_ack_active_negation << 4) | (hostdata->host_param.data_line_active_negation << 5); isp1020_mbox_command(host, param); if (param[0] != MBOX_COMMAND_COMPLETE) { restore_flags(flags); printk("qlogicisp : set active negation state failure\n"); return 1; } param[0] = MBOX_SET_PCI_CONTROL_PARAMS; param[1] = hostdata->host_param.data_dma_burst_enable << 1; param[2] = hostdata->host_param.command_dma_burst_enable << 1; isp1020_mbox_command(host, param); if (param[0] != MBOX_COMMAND_COMPLETE) { restore_flags(flags); printk("qlogicisp : set pci control parameter failure\n"); return 1; } isp_cfg1 = inw(host->io_port + ISP_CFG1); if (hostdata->host_param.data_dma_burst_enable || hostdata->host_param.command_dma_burst_enable) isp_cfg1 |= 0x0004; else isp_cfg1 &= 0xfffb; outw(isp_cfg1, host->io_port + ISP_CFG1); param[0] = MBOX_SET_TAG_AGE_LIMIT; param[1] = hostdata->host_param.tag_aging; isp1020_mbox_command(host, param); if (param[0] != MBOX_COMMAND_COMPLETE) { restore_flags(flags); printk("qlogicisp : set tag age limit failure\n"); return 1; } param[0] = MBOX_SET_SELECT_TIMEOUT; param[1] = hostdata->host_param.selection_timeout; isp1020_mbox_command(host, param); if (param[0] != MBOX_COMMAND_COMPLETE) { restore_flags(flags); printk("qlogicisp : set selection timeout failure\n"); return 1; } for (i = 0; i < MAX_TARGETS; i++) { if (!hostdata->dev_param[i].device_enable) continue; param[0] = MBOX_SET_TARGET_PARAMS; param[1] = i << 8; param[2] = hostdata->dev_param[i].device_flags << 8; param[3] = (hostdata->dev_param[i].synchronous_offset << 8) | hostdata->dev_param[i].synchronous_period; isp1020_mbox_command(host, param); if (param[0] != MBOX_COMMAND_COMPLETE) { restore_flags(flags); printk("qlogicisp : set target parameter failure\n"); return 1; } for (k = 0; k < MAX_LUNS; k++) { param[0] = MBOX_SET_DEV_QUEUE_PARAMS; param[1] = (i << 8) | k; param[2] = hostdata->host_param.max_queue_depth; param[3] = hostdata->dev_param[i].execution_throttle; isp1020_mbox_command(host, param); if (param[0] != MBOX_COMMAND_COMPLETE) { restore_flags(flags); printk("qlogicisp : set device queue " "parameter failure\n"); return 1; } } } queue_addr = (u_int) virt_to_bus(&hostdata->res[0][0]); param[0] = MBOX_INIT_RES_QUEUE; param[1] = RES_QUEUE_LEN + 1; param[2] = (u_short) (queue_addr >> 16); param[3] = (u_short) (queue_addr & 0xffff); param[4] = 0; param[5] = 0; isp1020_mbox_command(host, param); if (param[0] != MBOX_COMMAND_COMPLETE) { restore_flags(flags); printk("qlogicisp : set response queue failure\n"); return 1; } queue_addr = (u_int) virt_to_bus(&hostdata->req[0][0]); param[0] = MBOX_INIT_REQ_QUEUE; param[1] = QLOGICISP_REQ_QUEUE_LEN + 1; param[2] = (u_short) (queue_addr >> 16); param[3] = (u_short) (queue_addr & 0xffff); param[4] = 0; isp1020_mbox_command(host, param); if (param[0] != MBOX_COMMAND_COMPLETE) { restore_flags(flags); printk("qlogicisp : set request queue failure\n"); return 1; } restore_flags(flags); LEAVE("isp1020_load_parameters"); return 0; } /* * currently, this is only called during initialization or abort/reset, * at which times interrupts are disabled, so polling is OK, I guess... */ static int isp1020_mbox_command(struct Scsi_Host *host, u_short param[]) { int loop_count; if (mbox_param[param[0]] == 0) return 1; loop_count = DEFAULT_LOOP_COUNT; while (--loop_count && inw(host->io_port + HOST_HCCR) & 0x0080) barrier(); if (!loop_count) printk("qlogicisp: mbox_command loop timeout #1\n"); switch(mbox_param[param[0]] >> 4) { case 6: outw(param[5], host->io_port + MBOX5); case 5: outw(param[4], host->io_port + MBOX4); case 4: outw(param[3], host->io_port + MBOX3); case 3: outw(param[2], host->io_port + MBOX2); case 2: outw(param[1], host->io_port + MBOX1); case 1: outw(param[0], host->io_port + MBOX0); } outw(0x0, host->io_port + PCI_SEMAPHORE); outw(HCCR_CLEAR_RISC_INTR, host->io_port + HOST_HCCR); outw(HCCR_SET_HOST_INTR, host->io_port + HOST_HCCR); loop_count = DEFAULT_LOOP_COUNT; while (--loop_count && !(inw(host->io_port + PCI_INTF_STS) & 0x04)) barrier(); if (!loop_count) printk("qlogicisp: mbox_command loop timeout #2\n"); loop_count = DEFAULT_LOOP_COUNT; while (--loop_count && inw(host->io_port + MBOX0) == 0x04) barrier(); if (!loop_count) printk("qlogicisp: mbox_command loop timeout #3\n"); switch(mbox_param[param[0]] & 0xf) { case 6: param[5] = inw(host->io_port + MBOX5); case 5: param[4] = inw(host->io_port + MBOX4); case 4: param[3] = inw(host->io_port + MBOX3); case 3: param[2] = inw(host->io_port + MBOX2); case 2: param[1] = inw(host->io_port + MBOX1); case 1: param[0] = inw(host->io_port + MBOX0); } outw(0x0, host->io_port + PCI_SEMAPHORE); outw(HCCR_CLEAR_RISC_INTR, host->io_port + HOST_HCCR); return 0; } #if DEBUG_ISP1020_INTR void isp1020_print_status_entry(struct Status_Entry *status) { int i; printk("qlogicisp : entry count = 0x%02x, type = 0x%02x, flags = 0x%02x\n", status->hdr.entry_cnt, status->hdr.entry_type, status->hdr.flags); printk("qlogicisp : scsi status = 0x%04x, completion status = 0x%04x\n", le16_to_cpu(status->scsi_status), le16_to_cpu(status->completion_status)); printk("qlogicisp : state flags = 0x%04x, status flags = 0x%04x\n", le16_to_cpu(status->state_flags), le16_to_cpu(status->status_flags)); printk("qlogicisp : time = 0x%04x, request sense length = 0x%04x\n", le16_to_cpu(status->time), le16_to_cpu(status->req_sense_len)); printk("qlogicisp : residual transfer length = 0x%08x\n", le32_to_cpu(status->residual)); for (i = 0; i < le16_to_cpu(status->req_sense_len); i++) printk("qlogicisp : sense data = 0x%02x\n", status->req_sense_data[i]); } #endif /* DEBUG_ISP1020_INTR */ #if DEBUG_ISP1020 void isp1020_print_scsi_cmd(Scsi_Cmnd *cmd) { int i; printk("qlogicisp : target = 0x%02x, lun = 0x%02x, cmd_len = 0x%02x\n", cmd->target, cmd->lun, cmd->cmd_len); printk("qlogicisp : command = "); for (i = 0; i < cmd->cmd_len; i++) printk("0x%02x ", cmd->cmnd[i]); printk("\n"); } #endif /* DEBUG_ISP1020 */ #ifdef MODULE Scsi_Host_Template driver_template = QLOGICISP; #include "scsi_module.c" #endif /* MODULE */