/*********************************************************************** ;* File Name : TMSCSIM.H * ;* TEKRAM DC-390(T) PCI SCSI Bus Master Host Adapter * ;* Device Driver * ;***********************************************************************/ #ifndef _TMSCSIM_H #define _TMSCSIM_H #define IRQ_NONE 255 typedef unsigned char UCHAR; typedef unsigned short USHORT; typedef unsigned long ULONG; typedef unsigned int UINT; typedef UCHAR *PUCHAR; typedef USHORT *PUSHORT; typedef ULONG *PULONG; typedef Scsi_Host_Template *PSHT; typedef struct Scsi_Host *PSH; typedef Scsi_Device *PSCSIDEV; typedef Scsi_Cmnd *PSCSICMD; typedef void *PVOID; typedef struct scatterlist *PSGL, SGL; /*;-----------------------------------------------------------------------*/ typedef struct _SyncMsg { UCHAR ExtendMsg; UCHAR ExtMsgLen; UCHAR SyncXferReq; UCHAR Period; UCHAR ReqOffset; } SyncMsg; /*;-----------------------------------------------------------------------*/ typedef struct _Capacity { ULONG BlockCount; ULONG BlockLength; } Capacity; /*;-----------------------------------------------------------------------*/ typedef struct _SGentry { ULONG SGXferDataPtr; ULONG SGXferDataLen; } SGentry; typedef struct _SGentry1 { ULONG SGXLen; ULONG SGXPtr; } SGentry1, *PSGE; #define MAX_ADAPTER_NUM 4 #define MAX_DEVICES 10 #define MAX_SG_LIST_BUF 16 #define MAX_CMD_QUEUE 20 #define MAX_CMD_PER_LUN 8 #define MAX_SCSI_ID 8 #define MAX_SRB_CNT MAX_CMD_QUEUE+4 #define END_SCAN 2 #define SEL_TIMEOUT 153 /* 250 ms selection timeout (@ 40 MHz) */ /* ;----------------------------------------------------------------------- ; SCSI Request Block ;----------------------------------------------------------------------- */ struct _SRB { UCHAR CmdBlock[12]; struct _SRB *pNextSRB; struct _DCB *pSRBDCB; PSCSICMD pcmd; PSGL pSegmentList; ULONG PhysSRB; ULONG TotalXferredLen; ULONG SGPhysAddr; /*;a segment starting address */ ULONG SGToBeXferLen; /*; to be xfer length */ SGL Segmentx; /* make a one entry of S/G list table */ PUCHAR pMsgPtr; USHORT SRBState; USHORT Revxx2; /* ??? */ UCHAR MsgInBuf[6]; UCHAR MsgOutBuf[6]; UCHAR AdaptStatus; UCHAR TargetStatus; UCHAR MsgCnt; UCHAR EndMessage; UCHAR TagNumber; UCHAR SGcount; UCHAR SGIndex; UCHAR IORBFlag; /*;81h-Reset, 2-retry */ UCHAR SRBStatus; UCHAR RetryCnt; UCHAR SRBFlag; /*; b0-AutoReqSense,b6-Read,b7-write */ /*; b4-settimeout,b5-Residual valid */ UCHAR ScsiCmdLen; UCHAR ScsiPhase; UCHAR Reserved3[3]; /*;for dword alignment */ ULONG Segment0[2]; ULONG Segment1[2]; }; typedef struct _SRB DC390_SRB, *PSRB; /* ;----------------------------------------------------------------------- ; Device Control Block ;----------------------------------------------------------------------- */ struct _DCB { struct _DCB *pNextDCB; struct _ACB *pDCBACB; PSCSICMD pQIORBhead; PSCSICMD pQIORBtail; PSCSICMD AboIORBhead; PSCSICMD AboIORBtail; USHORT QIORBCnt; USHORT AboIORBcnt; PSRB pWaitingSRB; PSRB pWaitLast; PSRB pGoingSRB; PSRB pGoingLast; PSRB pActiveSRB; USHORT GoingSRBCnt; USHORT WaitSRBCnt; /* ??? */ ULONG TagMask; USHORT MaxCommand; USHORT AdaptIndex; /*; UnitInfo struc start */ USHORT UnitIndex; /*; nth Unit on this card */ UCHAR UnitSCSIID; /*; SCSI Target ID (SCSI Only) */ UCHAR UnitSCSILUN; /*; SCSI Log. Unit (SCSI Only) */ UCHAR IdentifyMsg; UCHAR CtrlR1; UCHAR CtrlR3; UCHAR CtrlR4; UCHAR InqDataBuf[8]; UCHAR CapacityBuf[8]; UCHAR DevMode; UCHAR AdpMode; UCHAR SyncMode; /*; 0:async mode */ UCHAR NegoPeriod; /*;for nego. */ UCHAR SyncPeriod; /*;for reg. */ UCHAR SyncOffset; /*;for reg. and nego.(low nibble) */ UCHAR UnitCtrlFlag; UCHAR DCBFlag; UCHAR DevType; UCHAR Reserved2[3]; /*;for dword alignment */ }; typedef struct _DCB DC390_DCB, *PDCB; /* ;----------------------------------------------------------------------- ; Adapter Control Block ;----------------------------------------------------------------------- */ struct _ACB { ULONG PhysACB; PSH pScsiHost; struct _ACB *pNextACB; USHORT IOPortBase; USHORT Revxx1; /* ??? */ PDCB pLinkDCB; PDCB pDCBRunRobin; PDCB pActiveDCB; PDCB pDCB_free; PSRB pFreeSRB; PSRB pTmpSRB; USHORT SRBCount; USHORT AdapterIndex; /*; nth Adapter this driver */ USHORT max_id; USHORT max_lun; UCHAR msgin123[4]; UCHAR status; UCHAR AdaptSCSIID; /*; Adapter SCSI Target ID */ UCHAR AdaptSCSILUN; /*; Adapter SCSI LUN */ UCHAR DeviceCnt; UCHAR IRQLevel; UCHAR TagMaxNum; UCHAR ACBFlag; UCHAR Gmode2; UCHAR LUNchk; UCHAR scan_devices; UCHAR HostID_Bit; UCHAR Reserved1[1]; /*;for dword alignment */ UCHAR DCBmap[MAX_SCSI_ID]; DC390_DCB DCB_array[MAX_DEVICES]; /* +74h, Len=3E8 */ DC390_SRB SRB_array[MAX_SRB_CNT]; /* +45Ch, Len= */ DC390_SRB TmpSRB; }; typedef struct _ACB DC390_ACB, *PACB; /*;-----------------------------------------------------------------------*/ #define BIT31 0x80000000 #define BIT30 0x40000000 #define BIT29 0x20000000 #define BIT28 0x10000000 #define BIT27 0x08000000 #define BIT26 0x04000000 #define BIT25 0x02000000 #define BIT24 0x01000000 #define BIT23 0x00800000 #define BIT22 0x00400000 #define BIT21 0x00200000 #define BIT20 0x00100000 #define BIT19 0x00080000 #define BIT18 0x00040000 #define BIT17 0x00020000 #define BIT16 0x00010000 #define BIT15 0x00008000 #define BIT14 0x00004000 #define BIT13 0x00002000 #define BIT12 0x00001000 #define BIT11 0x00000800 #define BIT10 0x00000400 #define BIT9 0x00000200 #define BIT8 0x00000100 #define BIT7 0x00000080 #define BIT6 0x00000040 #define BIT5 0x00000020 #define BIT4 0x00000010 #define BIT3 0x00000008 #define BIT2 0x00000004 #define BIT1 0x00000002 #define BIT0 0x00000001 /*;---UnitCtrlFlag */ #define UNIT_ALLOCATED BIT0 #define UNIT_INFO_CHANGED BIT1 #define FORMATING_MEDIA BIT2 #define UNIT_RETRY BIT3 /*;---UnitFlags */ #define DASD_SUPPORT BIT0 #define SCSI_SUPPORT BIT1 #define ASPI_SUPPORT BIT2 /*;----SRBState machine definition */ #define SRB_FREE 0 #define SRB_WAIT BIT0 #define SRB_READY BIT1 #define SRB_MSGOUT BIT2 /*;arbitration+msg_out 1st byte*/ #define SRB_MSGIN BIT3 #define SRB_MSGIN_MULTI BIT4 #define SRB_COMMAND BIT5 #define SRB_START_ BIT6 /*;arbitration+msg_out+command_out*/ #define SRB_DISCONNECT BIT7 #define SRB_DATA_XFER BIT8 #define SRB_XFERPAD BIT9 #define SRB_STATUS BIT10 #define SRB_COMPLETED BIT11 #define SRB_ABORT_SENT BIT12 #define DO_SYNC_NEGO BIT13 #define SRB_UNEXPECT_RESEL BIT14 /*;---ACBFlag */ #define RESET_DEV BIT0 #define RESET_DETECT BIT1 #define RESET_DONE BIT2 /*;---DCBFlag */ #define ABORT_DEV_ BIT0 /*;---SRBstatus */ #define SRB_OK BIT0 #define ABORTION BIT1 #define OVER_RUN BIT2 #define UNDER_RUN BIT3 #define PARITY_ERROR BIT4 #define SRB_ERROR BIT5 /*;---SRBFlag */ #define DATAOUT BIT7 #define DATAIN BIT6 #define RESIDUAL_VALID BIT5 #define ENABLE_TIMER BIT4 #define RESET_DEV0 BIT2 #define ABORT_DEV BIT1 #define AUTO_REQSENSE BIT0 /*;---Adapter status */ #define H_STATUS_GOOD 0 #define H_SEL_TIMEOUT 0x11 #define H_OVER_UNDER_RUN 0x12 #define H_UNEXP_BUS_FREE 0x13 #define H_TARGET_PHASE_F 0x14 #define H_INVALID_CCB_OP 0x16 #define H_LINK_CCB_BAD 0x17 #define H_BAD_TARGET_DIR 0x18 #define H_DUPLICATE_CCB 0x19 #define H_BAD_CCB_OR_SG 0x1A #define H_ABORT 0x0FF /*; SCSI Status byte codes*/ #define SCSI_STAT_GOOD 0x0 /*; Good status */ #define SCSI_STAT_CHECKCOND 0x02 /*; SCSI Check Condition */ #define SCSI_STAT_CONDMET 0x04 /*; Condition Met */ #define SCSI_STAT_BUSY 0x08 /*; Target busy status */ #define SCSI_STAT_INTER 0x10 /*; Intermediate status */ #define SCSI_STAT_INTERCONDMET 0x14 /*; Intermediate condition met */ #define SCSI_STAT_RESCONFLICT 0x18 /*; Reservation conflict */ #define SCSI_STAT_CMDTERM 0x22 /*; Command Terminated */ #define SCSI_STAT_QUEUEFULL 0x28 /*; Queue Full */ #define SCSI_STAT_UNEXP_BUS_F 0xFD /*; Unexpect Bus Free */ #define SCSI_STAT_BUS_RST_DETECT 0xFE /*; Scsi Bus Reset detected */ #define SCSI_STAT_SEL_TIMEOUT 0xFF /*; Selection Time out */ /*;---Sync_Mode */ #define SYNC_DISABLE 0 #define SYNC_ENABLE BIT0 #define SYNC_NEGO_DONE BIT1 #define WIDE_ENABLE BIT2 #define WIDE_NEGO_DONE BIT3 #define EN_TAG_QUEUING BIT4 #define EN_ATN_STOP BIT5 #define SYNC_NEGO_OFFSET 15 /*;---SCSI bus phase*/ #define SCSI_DATA_OUT 0 #define SCSI_DATA_IN 1 #define SCSI_COMMAND 2 #define SCSI_STATUS_ 3 #define SCSI_NOP0 4 #define SCSI_NOP1 5 #define SCSI_MSG_OUT 6 #define SCSI_MSG_IN 7 /*;----SCSI MSG BYTE*/ #define MSG_COMPLETE 0x00 #define MSG_EXTENDED 0x01 #define MSG_SAVE_PTR 0x02 #define MSG_RESTORE_PTR 0x03 #define MSG_DISCONNECT 0x04 #define MSG_INITIATOR_ERROR 0x05 #define MSG_ABORT 0x06 #define MSG_REJECT_ 0x07 #define MSG_NOP 0x08 #define MSG_PARITY_ERROR 0x09 #define MSG_LINK_CMD_COMPL 0x0A #define MSG_LINK_CMD_COMPL_FLG 0x0B #define MSG_BUS_RESET 0x0C #define MSG_ABORT_TAG 0x0D #define MSG_SIMPLE_QTAG 0x20 #define MSG_HEAD_QTAG 0x21 #define MSG_ORDER_QTAG 0x22 #define MSG_IDENTIFY 0x80 #define MSG_HOST_ID 0x0C0 /*;----SCSI STATUS BYTE*/ #define STATUS_GOOD 0x00 #define CHECK_CONDITION_ 0x02 #define STATUS_BUSY 0x08 #define STATUS_INTERMEDIATE 0x10 #define RESERVE_CONFLICT 0x18 /* cmd->result */ #define STATUS_MASK_ 0xFF #define MSG_MASK 0xFF00 #define RETURN_MASK 0xFF0000 /* ** Inquiry Data format */ typedef struct _SCSIInqData { /* INQ */ UCHAR DevType; /* Periph Qualifier & Periph Dev Type*/ UCHAR RMB_TypeMod; /* rem media bit & Dev Type Modifier */ UCHAR Vers; /* ISO, ECMA, & ANSI versions */ UCHAR RDF; /* AEN, TRMIOP, & response data format*/ UCHAR AddLen; /* length of additional data */ UCHAR Res1; /* reserved */ UCHAR Res2; /* reserved */ UCHAR Flags; /* RelADr,Wbus32,Wbus16,Sync,etc. */ UCHAR VendorID[8]; /* Vendor Identification */ UCHAR ProductID[16]; /* Product Identification */ UCHAR ProductRev[4]; /* Product Revision */ } SCSI_INQDATA, *PSCSI_INQDATA; /* Inquiry byte 0 masks */ #define SCSI_DEVTYPE 0x1F /* Peripheral Device Type */ #define SCSI_PERIPHQUAL 0xE0 /* Peripheral Qualifier */ /* Inquiry byte 1 mask */ #define SCSI_REMOVABLE_MEDIA 0x80 /* Removable Media bit (1=removable) */ /* Peripheral Device Type definitions */ #define SCSI_DASD 0x00 /* Direct-access Device */ #define SCSI_SEQACESS 0x01 /* Sequential-access device */ #define SCSI_PRINTER 0x02 /* Printer device */ #define SCSI_PROCESSOR 0x03 /* Processor device */ #define SCSI_WRITEONCE 0x04 /* Write-once device */ #define SCSI_CDROM 0x05 /* CD-ROM device */ #define SCSI_SCANNER 0x06 /* Scanner device */ #define SCSI_OPTICAL 0x07 /* Optical memory device */ #define SCSI_MEDCHGR 0x08 /* Medium changer device */ #define SCSI_COMM 0x09 /* Communications device */ #define SCSI_NODEV 0x1F /* Unknown or no device type */ /* ** Inquiry flag definitions (Inq data byte 7) */ #define SCSI_INQ_RELADR 0x80 /* device supports relative addressing*/ #define SCSI_INQ_WBUS32 0x40 /* device supports 32 bit data xfers */ #define SCSI_INQ_WBUS16 0x20 /* device supports 16 bit data xfers */ #define SCSI_INQ_SYNC 0x10 /* device supports synchronous xfer */ #define SCSI_INQ_LINKED 0x08 /* device supports linked commands */ #define SCSI_INQ_CMDQUEUE 0x02 /* device supports command queueing */ #define SCSI_INQ_SFTRE 0x01 /* device supports soft resets */ /* ;========================================================== ; EEPROM byte offset ;========================================================== */ typedef struct _EEprom { UCHAR EE_MODE1; UCHAR EE_SPEED; UCHAR xx1; UCHAR xx2; } EEprom, *PEEprom; #define EE_ADAPT_SCSI_ID 64 #define EE_MODE2 65 #define EE_DELAY 66 #define EE_TAG_CMD_NUM 67 /*; EE_MODE1 bits definition*/ #define PARITY_CHK_ BIT0 #define SYNC_NEGO_ BIT1 #define EN_DISCONNECT_ BIT2 #define SEND_START_ BIT3 #define TAG_QUEUING_ BIT4 /*; EE_MODE2 bits definition*/ #define MORE2_DRV BIT0 #define GREATER_1G BIT1 #define RST_SCSI_BUS BIT2 #define ACTIVE_NEGATION BIT3 #define NO_SEEK BIT4 #define LUN_CHECK BIT5 #define ENABLE_CE 1 #define DISABLE_CE 0 #define EEPROM_READ 0x80 /* ;========================================================== ; AMD 53C974 Registers bit Definition ;========================================================== */ /* ;==================== ; SCSI Register ;==================== */ /*; Command Reg.(+0CH) */ #define DMA_COMMAND BIT7 #define NOP_CMD 0 #define CLEAR_FIFO_CMD 1 #define RST_DEVICE_CMD 2 #define RST_SCSI_BUS_CMD 3 #define INFO_XFER_CMD 0x10 #define INITIATOR_CMD_CMPLTE 0x11 #define MSG_ACCEPTED_CMD 0x12 #define XFER_PAD_BYTE 0x18 #define SET_ATN_CMD 0x1A #define RESET_ATN_CMD 0x1B #define SELECT_W_ATN 0x42 #define SEL_W_ATN_STOP 0x43 #define EN_SEL_RESEL 0x44 #define SEL_W_ATN2 0x46 #define DATA_XFER_CMD INFO_XFER_CMD /*; SCSI Status Reg.(+10H) */ #define INTERRUPT BIT7 #define ILLEGAL_OP_ERR BIT6 #define PARITY_ERR BIT5 #define COUNT_2_ZERO BIT4 #define GROUP_CODE_VALID BIT3 #define SCSI_PHASE_MASK (BIT2+BIT1+BIT0) /*; Interrupt Status Reg.(+14H) */ #define SCSI_RESET BIT7 #define INVALID_CMD BIT6 #define DISCONNECTED BIT5 #define SERVICE_REQUEST BIT4 #define SUCCESSFUL_OP BIT3 #define RESELECTED BIT2 #define SEL_ATTENTION BIT1 #define SELECTED BIT0 /*; Internal State Reg.(+18H) */ #define SYNC_OFFSET_FLAG BIT3 #define INTRN_STATE_MASK (BIT2+BIT1+BIT0) /*; Clock Factor Reg.(+24H) */ #define CLK_FREQ_40MHZ 0 #define CLK_FREQ_35MHZ (BIT2+BIT1+BIT0) #define CLK_FREQ_30MHZ (BIT2+BIT1) #define CLK_FREQ_25MHZ (BIT2+BIT0) #define CLK_FREQ_20MHZ BIT2 #define CLK_FREQ_15MHZ (BIT1+BIT0) #define CLK_FREQ_10MHZ BIT1 /*; Control Reg. 1(+20H) */ #define EXTENDED_TIMING BIT7 #define DIS_INT_ON_SCSI_RST BIT6 #define PARITY_ERR_REPO BIT4 #define SCSI_ID_ON_BUS (BIT2+BIT1+BIT0) /*; Control Reg. 2(+2CH) */ #define EN_FEATURE BIT6 #define EN_SCSI2_CMD BIT3 /*; Control Reg. 3(+30H) */ #define ID_MSG_CHECK BIT7 #define EN_QTAG_MSG BIT6 #define EN_GRP2_CMD BIT5 #define FAST_SCSI BIT4 /* ;10MB/SEC */ #define FAST_CLK BIT3 /* ;25 - 40 MHZ */ /*; Control Reg. 4(+34H) */ #define EATER_12NS 0 #define EATER_25NS BIT7 #define EATER_35NS BIT6 #define EATER_0NS (BIT7+BIT6) #define NEGATE_REQACKDATA BIT2 #define NEGATE_REQACK BIT3 /* ;==================== ; DMA Register ;==================== */ /*; DMA Command Reg.(+40H) */ #define READ_DIRECTION BIT7 #define WRITE_DIRECTION 0 #define EN_DMA_INT BIT6 #define MAP_TO_MDL BIT5 #define DIAGNOSTIC BIT4 #define DMA_IDLE_CMD 0 #define DMA_BLAST_CMD BIT0 #define DMA_ABORT_CMD BIT1 #define DMA_START_CMD (BIT1+BIT0) /*; DMA Status Reg.(+54H) */ #define PCI_MS_ABORT BIT6 #define BLAST_COMPLETE BIT5 #define SCSI_INTERRUPT BIT4 #define DMA_XFER_DONE BIT3 #define DMA_XFER_ABORT BIT2 #define DMA_XFER_ERROR BIT1 #define POWER_DOWN BIT0 /* ; DMA SCSI Bus and Ctrl.(+70H) ;EN_INT_ON_PCI_ABORT */ /* ;========================================================== ; SCSI Chip register address offset ;========================================================== */ #define CtcReg_Low 0x00 #define CtcReg_Mid 0x04 #define ScsiFifo 0x08 #define ScsiCmd 0x0C #define Scsi_Status 0x10 #define INT_Status 0x14 #define Sync_Period 0x18 #define Sync_Offset 0x1C #define CtrlReg1 0x20 #define Clk_Factor 0x24 #define CtrlReg2 0x2C #define CtrlReg3 0x30 #define CtrlReg4 0x34 #define CtcReg_High 0x38 #define DMA_Cmd 0x40 #define DMA_XferCnt 0x44 #define DMA_XferAddr 0x48 #define DMA_Wk_ByteCntr 0x4C #define DMA_Wk_AddrCntr 0x50 #define DMA_Status 0x54 #define DMA_MDL_Addr 0x58 #define DMA_Wk_MDL_Cntr 0x5C #define DMA_ScsiBusCtrl 0x70 #define StcReg_Low CtcReg_Low #define StcReg_Mid CtcReg_Mid #define Scsi_Dest_ID Scsi_Status #define Scsi_TimeOut INT_Status #define Intern_State Sync_Period #define Current_Fifo Sync_Offset #define StcReg_High CtcReg_High #define am_target Scsi_Status #define am_timeout INT_Status #define am_seq_step Sync_Period #define am_fifo_count Sync_Offset #define DC390_read8(address) \ inb(DC390_ioport + (address))) #define DC390_read16(address) \ inw(DC390_ioport + (address))) #define DC390_read32(address) \ inl(DC390_ioport + (address))) #define DC390_write8(address,value) \ outb((value), DC390_ioport + (address))) #define DC390_write16(address,value) \ outw((value), DC390_ioport + (address))) #define DC390_write32(address,value) \ outl((value), DC390_ioport + (address))) #endif /* _TMSCSIM_H */