/*****************************************************************************/ /* * cd1400.h -- cd1400 UART hardware info. * * Copyright (C) 1996-1997 Stallion Technologies (support@stallion.oz.au). * Copyright (C) 1994-1996 Greg Ungerer (gerg@stallion.oz.au). * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ /*****************************************************************************/ #ifndef _CD1400_H #define _CD1400_H /*****************************************************************************/ /* * Define the number of async ports per cd1400 uart chip. */ #define CD1400_PORTS 4 /* * Define the cd1400 uarts internal FIFO sizes. */ #define CD1400_TXFIFOSIZE 12 #define CD1400_RXFIFOSIZE 12 /* * Local RX FIFO thresh hold level. Also define the RTS thresh hold * based on the RX thresh hold. */ #define FIFO_RXTHRESHOLD 6 #define FIFO_RTSTHRESHOLD 7 /*****************************************************************************/ /* * Define the cd1400 register addresses. These are all the valid * registers with the cd1400. Some are global, some virtual, some * per port. */ #define GFRCR 0x40 #define CAR 0x68 #define GCR 0x4b #define SVRR 0x67 #define RICR 0x44 #define TICR 0x45 #define MICR 0x46 #define RIR 0x6b #define TIR 0x6a #define MIR 0x69 #define PPR 0x7e #define RIVR 0x43 #define TIVR 0x42 #define MIVR 0x41 #define TDR 0x63 #define RDSR 0x62 #define MISR 0x4c #define EOSRR 0x60 #define LIVR 0x18 #define CCR 0x05 #define SRER 0x06 #define COR1 0x08 #define COR2 0x09 #define COR3 0x0a #define COR4 0x1e #define COR5 0x1f #define CCSR 0x0b #define RDCR 0x0e #define SCHR1 0x1a #define SCHR2 0x1b #define SCHR3 0x1c #define SCHR4 0x1d #define SCRL 0x22 #define SCRH 0x23 #define LNC 0x24 #define MCOR1 0x15 #define MCOR2 0x16 #define RTPR 0x21 #define MSVR1 0x6c #define MSVR2 0x6d #define PSVR 0x6f #define RBPR 0x78 #define RCOR 0x7c #define TBPR 0x72 #define TCOR 0x76 /*****************************************************************************/ /* * Define the set of baud rate clock divisors. */ #define CD1400_CLK0 8 #define CD1400_CLK1 32 #define CD1400_CLK2 128 #define CD1400_CLK3 512 #define CD1400_CLK4 2048 #define CD1400_NUMCLKS 5 /*****************************************************************************/ /* * Define the clock pre-scalar value to be a 5 ms clock. This should be * OK for now. It would probably be better to make it 10 ms, but we * can't fit that divisor into 8 bits! */ #define PPR_SCALAR 244 /*****************************************************************************/ /* * Define values used to set character size options. */ #define COR1_CHL5 0x00 #define COR1_CHL6 0x01 #define COR1_CHL7 0x02 #define COR1_CHL8 0x03 /* * Define values used to set the number of stop bits. */ #define COR1_STOP1 0x00 #define COR1_STOP15 0x04 #define COR1_STOP2 0x08 /* * Define values used to set the parity scheme in use. */ #define COR1_PARNONE 0x00 #define COR1_PARFORCE 0x20 #define COR1_PARENB 0x40 #define COR1_PARIGNORE 0x10 #define COR1_PARODD 0x80 #define COR1_PAREVEN 0x00 #define COR2_IXM 0x80 #define COR2_TXIBE 0x40 #define COR2_ETC 0x20 #define COR2_LLM 0x10 #define COR2_RLM 0x08 #define COR2_RTSAO 0x04 #define COR2_CTSAE 0x02 #define COR3_SCDRNG 0x80 #define COR3_SCD34 0x40 #define COR3_FCT 0x20 #define COR3_SCD12 0x10 /* * Define values used by COR4. */ #define COR4_BRKINT 0x08 #define COR4_IGNBRK 0x18 /*****************************************************************************/ /* * Define the modem control register values. * Note that the actual hardware is a little different to the conventional * pin names on the cd1400. */ #define MSVR1_DTR 0x01 #define MSVR1_DSR 0x10 #define MSVR1_RI 0x20 #define MSVR1_CTS 0x40 #define MSVR1_DCD 0x80 #define MSVR2_RTS 0x02 #define MSVR2_DSR 0x10 #define MSVR2_RI 0x20 #define MSVR2_CTS 0x40 #define MSVR2_DCD 0x80 #define MCOR1_DCD 0x80 #define MCOR1_CTS 0x40 #define MCOR1_RI 0x20 #define MCOR1_DSR 0x10 #define MCOR2_DCD 0x80 #define MCOR2_CTS 0x40 #define MCOR2_RI 0x20 #define MCOR2_DSR 0x10 /*****************************************************************************/ /* * Define the bits used with the service (interrupt) enable register. */ #define SRER_NNDT 0x01 #define SRER_TXEMPTY 0x02 #define SRER_TXDATA 0x04 #define SRER_RXDATA 0x10 #define SRER_MODEM 0x80 /*****************************************************************************/ /* * Define operational commands for the command register. */ #define CCR_RESET 0x80 #define CCR_CORCHANGE 0x4e #define CCR_SENDCH 0x20 #define CCR_CHANCTRL 0x10 #define CCR_TXENABLE (CCR_CHANCTRL | 0x08) #define CCR_TXDISABLE (CCR_CHANCTRL | 0x04) #define CCR_RXENABLE (CCR_CHANCTRL | 0x02) #define CCR_RXDISABLE (CCR_CHANCTRL | 0x01) #define CCR_SENDSCHR1 (CCR_SENDCH | 0x01) #define CCR_SENDSCHR2 (CCR_SENDCH | 0x02) #define CCR_SENDSCHR3 (CCR_SENDCH | 0x03) #define CCR_SENDSCHR4 (CCR_SENDCH | 0x04) #define CCR_RESETCHAN (CCR_RESET | 0x00) #define CCR_RESETFULL (CCR_RESET | 0x01) #define CCR_TXFLUSHFIFO (CCR_RESET | 0x02) #define CCR_MAXWAIT 10000 /*****************************************************************************/ /* * Define the valid acknowledgement types (for hw ack cycle). */ #define ACK_TYPMASK 0x07 #define ACK_TYPTX 0x02 #define ACK_TYPMDM 0x01 #define ACK_TYPRXGOOD 0x03 #define ACK_TYPRXBAD 0x07 #define SVRR_RX 0x01 #define SVRR_TX 0x02 #define SVRR_MDM 0x04 #define ST_OVERRUN 0x01 #define ST_FRAMING 0x02 #define ST_PARITY 0x04 #define ST_BREAK 0x08 #define ST_SCHAR1 0x10 #define ST_SCHAR2 0x20 #define ST_SCHAR3 0x30 #define ST_SCHAR4 0x40 #define ST_RANGE 0x70 #define ST_SCHARMASK 0x70 #define ST_TIMEOUT 0x80 #define MISR_DCD 0x80 #define MISR_CTS 0x40 #define MISR_RI 0x20 #define MISR_DSR 0x10 /*****************************************************************************/ /* * Defines for the CCSR status register. */ #define CCSR_RXENABLED 0x80 #define CCSR_RXFLOWON 0x40 #define CCSR_RXFLOWOFF 0x20 #define CCSR_TXENABLED 0x08 #define CCSR_TXFLOWON 0x04 #define CCSR_TXFLOWOFF 0x02 /*****************************************************************************/ /* * Define the embedded commands. */ #define ETC_CMD 0x00 #define ETC_STARTBREAK 0x81 #define ETC_DELAY 0x82 #define ETC_STOPBREAK 0x83 /*****************************************************************************/ #endif