1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
|
#
# This file is used for selecting non-standard netcard options, and
# need not be modified for typical use.
#
# Drivers are *not* selected in this file, but rather with files
# automatically generated during the top-level kernel configuration.
#
# Special options supported, indexed by their 'config' name:
#
# CONFIG_WD80x3 The Western Digital (SMC) WD80x3 driver
# WD_SHMEM=xxx Forces the address of the shared memory
# WD_no_mapout Don't map out the shared memory (faster, but
# your machine may not warm-boot).
# CONFIG_NE2000 The NE-[12]000 clone driver.
# PACKETBUF_MEMSIZE Allows an extra-large packet buffer to be
# used. Usually pointless under Linux.
# show_all_SAPROM Show the entire address PROM, not just the
# ethernet address, during boot.
# rw_bugfix Patch an obscure bug with a version of the 8390.
# CONFIG_HPLAN The HP-LAN driver (for 8390-based boards only).
# rw_bugfix Fix the same obscure bug.
# CONFIG_EL2 The 3c503 EtherLink II driver
# EL2_AUI Default to the AUI port instead of the BNC port
# no_probe_nonshared_memory Don't probe for programmed-I/O boards.
# EL2MEMTEST Test shared memory at boot-time.
# CONFIG_PLIP The Crynwr-protocol PL/IP driver
# INITIALTIMEOUTFACTOR Timing parameters.
# MAXTIMEOUTFACTOR
# DE600 The D-Link DE-600 Portable Ethernet Adaptor.
# DE600_IO The DE600 I/O-port address (0x378 == default)
# DE600_IRQ The DE600 IRQ number to use (IRQ7 == default)
# DE600_DEBUG Enable or disable DE600 debugging (default off)
# DE620 The D-Link DE-600 Portable Ethernet Adaptor.
# DE620_IO The DE620 I/O-port address (0x378 == default)
# DE620_IRQ The DE620 IRQ number to use (IRQ7 == default)
# DE620_DEBUG Enable or disable DE600 debugging (default off)
# DEPCA The DIGITAL series of LANCE based Ethernet Cards
# (DEPCA, DE100, DE200/1/2, DE210, DE422 (EISA))
# EWRK3 The DIGITAL series of AT Ethernet Cards (DE203/4/5)
# EWRK3_DEBUG Set the desired debug level
#
# DE4x5 The DIGITAL series of PCI/EISA Ethernet Cards,
# DE425, DE434, DE435, DE500
# DE4X5_DEBUG Set the desired debug level
# IS_NOT_DEC May allow driver to work with Zynx & SMC cards -
# see linux/drivers/net/README.de4x5
# DE4X5_AUTOSENSE (Default) auto media/mode selection
# If you want at least one board to not autosense then
# no board can autosense. For a board mix of several
# types, OR the manual values [eg for a DE500 (100M) with
# a DE450 (AUI) use '-DDE4X5_AUTOSENSE=(0x80|0x08)']
# For full auto media/mode selection = 0x4000
# For manual TP media selection = 0x01
# For manual TP/Nway media selection (DC21041) = 0x02
# For manual BNC media selection = 0x04
# For manual AUI media selection = 0x08
# For manual BNC/AUI media selection (DC21040) = 0x10
# For manual 10Mb/s mode selection (DC21140) = 0x40
# For manual 100Mb/s mode selection (DC21140) = 0x80
# The DC21040 will default to TP if TP_NW is specified
# The DC21041 will default to BNC if BNC_AUI is specified
# The DC21140 needs it's speed to be manually set to
# 10Mb/s or 100Mb/s (AUTO defaults to 10Mb/s)
#
# The following options exist, but cannot be set in this file.
# lance.c
# LANCE_DMA Change the default DMA to other than DMA5.
# 8390.c
# NO_PINGPONG Disable ping-pong transmit buffers.
# Most drivers also have a *_DEBUG setting that may be adjusted.
# The 8390 drivers share the EI_DEBUG setting.
# General options for Space.c
OPTS = # -DETH0_ADDR=0x300 -DETH0_IRQ=11
WD_OPTS = #-DWD_SHMEM=0xDD000
EL2_OPTS = #-DEL2_AUI
NE_OPTS =
HP_OPTS =
PLIP_OPTS =
DEPCA_OPTS = -DDEPCA_DEBUG=1
EWRK3_OPTS = -DEWRK3_DEBUG=1
DE4X5_OPTS = -DDE4X5_DEBUG=1 -DDE4X5_AUTOSENSE=0x4000
ELP_OPTS = -DELP_DEBUG=1 -DELP_NEED_HARD_RESET=0
|
