blob: e4bcdde0027ec0711ad09de3eaf134952cd0ff83 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
|
/*
* include/asm-ppc/cache.h
*/
#ifdef __KERNEL__
#ifndef __ARCH_PPC_CACHE_H
#define __ARCH_PPC_CACHE_H
#include <linux/config.h>
#include <asm/processor.h>
/* bytes per L1 cache line */
#if !defined(CONFIG_8xx) || defined(CONFIG_8260)
#if defined(CONFIG_PPC64BRIDGE)
#define L1_CACHE_BYTES 128
#else
#define L1_CACHE_BYTES 32
#endif /* PPC64 */
#else
#define L1_CACHE_BYTES 16
#endif /* !8xx || 8260 */
#define L1_CACHE_ALIGN(x) (((x)+(L1_CACHE_BYTES-1))&~(L1_CACHE_BYTES-1))
#define L1_CACHE_PAGES 8
#define SMP_CACHE_BYTES L1_CACHE_BYTES
#ifdef MODULE
#define __cacheline_aligned __attribute__((__aligned__(L1_CACHE_BYTES)))
#else
#define __cacheline_aligned \
__attribute__((__aligned__(L1_CACHE_BYTES), \
__section__(".data.cacheline_aligned")))
#endif
#if defined(__KERNEL__) && !defined(__ASSEMBLY__)
extern void flush_dcache_range(unsigned long start, unsigned long stop);
#endif /* __ASSEMBLY__ */
/* prep registers for L2 */
#define CACHECRBA 0x80000823 /* Cache configuration register address */
#define L2CACHE_MASK 0x03 /* Mask for 2 L2 Cache bits */
#define L2CACHE_512KB 0x00 /* 512KB */
#define L2CACHE_256KB 0x01 /* 256KB */
#define L2CACHE_1MB 0x02 /* 1MB */
#define L2CACHE_NONE 0x03 /* NONE */
#define L2CACHE_PARITY 0x08 /* Mask for L2 Cache Parity Protected bit */
#ifdef CONFIG_8xx
/* Cache control on the MPC8xx is provided through some additional
* special purpose registers.
*/
#define IC_CST 560 /* Instruction cache control/status */
#define IC_ADR 561 /* Address needed for some commands */
#define IC_DAT 562 /* Read-only data register */
#define DC_CST 568 /* Data cache control/status */
#define DC_ADR 569 /* Address needed for some commands */
#define DC_DAT 570 /* Read-only data register */
/* Commands. Only the first few are available to the instruction cache.
*/
#define IDC_ENABLE 0x02000000 /* Cache enable */
#define IDC_DISABLE 0x04000000 /* Cache disable */
#define IDC_LDLCK 0x06000000 /* Load and lock */
#define IDC_UNLINE 0x08000000 /* Unlock line */
#define IDC_UNALL 0x0a000000 /* Unlock all */
#define IDC_INVALL 0x0c000000 /* Invalidate all */
#define DC_FLINE 0x0e000000 /* Flush data cache line */
#define DC_SFWT 0x01000000 /* Set forced writethrough mode */
#define DC_CFWT 0x03000000 /* Clear forced writethrough mode */
#define DC_SLES 0x05000000 /* Set little endian swap mode */
#define DC_CLES 0x07000000 /* Clear little endian swap mode */
/* Status.
*/
#define IDC_ENABLED 0x80000000 /* Cache is enabled */
#define IDC_CERR1 0x00200000 /* Cache error 1 */
#define IDC_CERR2 0x00100000 /* Cache error 2 */
#define IDC_CERR3 0x00080000 /* Cache error 3 */
#define DC_DFWT 0x40000000 /* Data cache is forced write through */
#define DC_LES 0x20000000 /* Caches are little endian mode */
#endif /* CONFIG_8xx */
#endif
#endif /* __KERNEL__ */
|
