diff options
Diffstat (limited to 'drivers/net/CONFIG')
| -rw-r--r-- | drivers/net/CONFIG | 102 |
1 files changed, 0 insertions, 102 deletions
diff --git a/drivers/net/CONFIG b/drivers/net/CONFIG deleted file mode 100644 index 8ea48df1b..000000000 --- a/drivers/net/CONFIG +++ /dev/null @@ -1,102 +0,0 @@ -# -# This file is used for selecting non-standard netcard options, and -# need not be modified for typical use. -# -# Drivers are *not* selected in this file, but rather with files -# automatically generated during the top-level kernel configuration. -# -# Special options supported, indexed by their 'config' name: -# -# CONFIG_WD80x3 The Western Digital (SMC) WD80x3 driver -# WD_SHMEM=xxx Forces the address of the shared memory -# CONFIG_NE2000 The NE-[12]000 clone driver. -# PACKETBUF_MEMSIZE Allows an extra-large packet buffer to be -# used. Usually pointless under Linux. -# show_all_SAPROM Show the entire address PROM, not just the -# ethernet address, during boot. -# CONFIG_NE_RW_BUGFIX Patch an obscure bug with a version of the 8390. -# CONFIG_NE_SANITY Double check the internal card xfer address -# against the driver's value. Useful for debugging. -# CONFIG_HPLAN The HP-LAN driver (for 8390-based boards only). -# rw_bugfix Fix the same obscure bug. -# CONFIG_EL2 The 3c503 EtherLink II driver -# EL2_AUI Default to the AUI port instead of the BNC port -# no_probe_nonshared_memory Don't probe for programmed-I/O boards. -# EL2MEMTEST Test shared memory at boot-time. -# CONFIG_PLIP The Crynwr-protocol PL/IP driver -# INITIALTIMEOUTFACTOR Timing parameters. -# MAXTIMEOUTFACTOR -# DE600 The D-Link DE-600 Portable Ethernet Adaptor. -# DE600_IO The DE600 I/O-port address (0x378 == default) -# DE600_IRQ The DE600 IRQ number to use (IRQ7 == default) -# DE600_DEBUG Enable or disable DE600 debugging (default off) -# DE620 The D-Link DE-600 Portable Ethernet Adaptor. -# DE620_IO The DE620 I/O-port address (0x378 == default) -# DE620_IRQ The DE620 IRQ number to use (IRQ7 == default) -# DE620_DEBUG Enable or disable DE600 debugging (default off) -# DEPCA The DIGITAL series of LANCE based Ethernet Cards -# (DEPCA, DE100, DE200/1/2, DE210, DE422 (EISA)) -# EWRK3 The DIGITAL series of AT Ethernet Cards (DE203/4/5) -# EWRK3_DEBUG Set the desired debug level -# -# DE4x5 The DIGITAL series of PCI/EISA Ethernet Cards, -# DE425, DE434, DE435, DE450, DE500 -# DE4X5_DEBUG Set the desired debug level -# DEC_ONLY Allows driver to work with DIGITAL cards only - -# see linux/drivers/net/README.de4x5 -# DE4X5_AUTOSENSE (Default) auto media/mode selection -# If you want at least one board to not autosense then -# no board can autosense. For a board mix of several -# types, OR the manual values [eg for a DE500 (100M) with -# a DE450 (AUI) use '-DDE4X5_AUTOSENSE=(_100Mb|AUI)'] -# For full auto media/mode selection = AUTO -# For manual TP media selection = TP -# For manual TP/Nway media selection (DC21041) = TP_NW -# For manual BNC media selection = BNC -# For manual AUI media selection = AUI -# For manual BNC/AUI media selection (DC21040) = BNC_AUI -# For manual 10Mb/s mode selection (DC21140) = _10Mb -# For manual 100Mb/s mode selection (DC21140) = _100Mb -# The DC21040 will default to TP if TP_NW is specified -# The DC21041 will default to BNC if BNC_AUI is specified -# DE4X5_DO_MEMCPY Forces the Intels to use memory copies into sk_buffs -# rather than straight DMA. -# -# DEFXX The DIGITAL series of FDDI EISA (DEFEA) and PCI (DEFPA) -# controllers -# DEFXX_DEBUG Set the desired debug level -# -# TULIP Tulip (dc21040/dc21041/ds21140) driver -# TULIP_PORT specify default if_port -# 0: 10TP -# 1: 100Tx(ds21140)/AUI(dc2104x) -# 2: BNC(dc2104x) -# TULIP_FIX_PORT don't change if_port automatically if defined -# TULIP_MAX_CARDS maximum number of probed card -# - -# The following options exist, but cannot be set in this file. -# lance.c -# LANCE_DMA Change the default DMA to other than DMA5. -# 8390.c -# NO_PINGPONG Disable ping-pong transmit buffers. - - -# Most drivers also have a *_DEBUG setting that may be adjusted. -# The 8390 drivers share the EI_DEBUG setting. - -# General options for Space.c -OPTS = # -DETH0_ADDR=0x300 -DETH0_IRQ=11 - -WD_OPTS = #-DWD_SHMEM=0xDD000 -EL2_OPTS = #-DEL2_AUI -NE_OPTS = -HP_OPTS = -PLIP_OPTS = -DEPCA_OPTS = -EWRK3_OPTS = -DE4X5_OPTS = -DDE4X5_AUTOSENSE=AUTO -DEFXX_OPTS = -ELP_OPTS = -TULIP_OPTS = -CS89x0_OPTS = |