diff options
Diffstat (limited to 'drivers/usb/serial/io_16654.h')
| -rw-r--r-- | drivers/usb/serial/io_16654.h | 195 |
1 files changed, 195 insertions, 0 deletions
diff --git a/drivers/usb/serial/io_16654.h b/drivers/usb/serial/io_16654.h new file mode 100644 index 000000000..b2019d668 --- /dev/null +++ b/drivers/usb/serial/io_16654.h @@ -0,0 +1,195 @@ +/************************************************************************ + * + * 16654.H Definitions for 16C654 UART used on EdgePorts + * + * Copyright (c) 1998 Inside Out Networks, Inc. + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + ************************************************************************/ + +#if !defined(_16654_H) +#define _16654_H + +/************************************************************************ + * + * D e f i n e s / T y p e d e f s + * + ************************************************************************/ + + // + // UART register numbers + // Numbers 0-7 are passed to the Edgeport directly. Numbers 8 and + // above are used internally to indicate that we must enable access + // to them via LCR bit 0x80 or LCR = 0xBF. + // The register number sent to the Edgeport is then (x & 0x7). + // + // Driver must not access registers that affect operation of the + // the EdgePort firmware -- that includes THR, RHR, IER, FCR. + + +#define THR 0 // ! Transmit Holding Register (Write) +#define RDR 0 // ! Receive Holding Register (Read) +#define IER 1 // ! Interrupt Enable Register +#define FCR 2 // ! Fifo Control Register (Write) +#define ISR 2 // Interrupt Status Register (Read) +#define LCR 3 // Line Control Register +#define MCR 4 // Modem Control Register +#define LSR 5 // Line Status Register +#define MSR 6 // Modem Status Register +#define SPR 7 // ScratchPad Register +#define DLL 8 // Bank2[ 0 ] Divisor Latch LSB +#define DLM 9 // Bank2[ 1 ] Divisor Latch MSB +#define EFR 10 // Bank2[ 2 ] Extended Function Register +//efine unused 11 // Bank2[ 3 ] +#define XON1 12 // Bank2[ 4 ] Xon-1 +#define XON2 13 // Bank2[ 5 ] Xon-2 +#define XOFF1 14 // Bank2[ 6 ] Xoff-1 +#define XOFF2 15 // Bank2[ 7 ] Xoff-2 + +#define NUM_16654_REGS 16 + +#define IS_REG_2ND_BANK(x) ((x) >= 8) + + // + // Bit definitions for each register + // + +#define IER_RX 0x01 // Enable receive interrupt +#define IER_TX 0x02 // Enable transmit interrupt +#define IER_RXS 0x04 // Enable receive status interrupt +#define IER_MDM 0x08 // Enable modem status interrupt +#define IER_SLEEP 0x10 // Enable sleep mode +#define IER_XOFF 0x20 // Enable s/w flow control (XOFF) interrupt +#define IER_RTS 0x40 // Enable RTS interrupt +#define IER_CTS 0x80 // Enable CTS interrupt +#define IER_ENABLE_ALL 0xFF // Enable all ints + + +#define FCR_FIFO_EN 0x01 // Enable FIFOs +#define FCR_RXCLR 0x02 // Reset Rx FIFO +#define FCR_TXCLR 0x04 // Reset Tx FIFO +#define FCR_DMA_BLK 0x08 // Enable DMA block mode +#define FCR_TX_LEVEL_MASK 0x30 // Mask for Tx FIFO Level +#define FCR_TX_LEVEL_8 0x00 // Tx FIFO Level = 8 bytes +#define FCR_TX_LEVEL_16 0x10 // Tx FIFO Level = 16 bytes +#define FCR_TX_LEVEL_32 0x20 // Tx FIFO Level = 32 bytes +#define FCR_TX_LEVEL_56 0x30 // Tx FIFO Level = 56 bytes +#define FCR_RX_LEVEL_MASK 0xC0 // Mask for Rx FIFO Level +#define FCR_RX_LEVEL_8 0x00 // Rx FIFO Level = 8 bytes +#define FCR_RX_LEVEL_16 0x40 // Rx FIFO Level = 16 bytes +#define FCR_RX_LEVEL_56 0x80 // Rx FIFO Level = 56 bytes +#define FCR_RX_LEVEL_60 0xC0 // Rx FIFO Level = 60 bytes + + +#define ISR_INT_MDM_STATUS 0x00 // Modem status int pending +#define ISR_INT_NONE 0x01 // No interrupt pending +#define ISR_INT_TXRDY 0x02 // Tx ready int pending +#define ISR_INT_RXRDY 0x04 // Rx ready int pending +#define ISR_INT_LINE_STATUS 0x06 // Line status int pending +#define ISR_INT_RX_TIMEOUT 0x0C // Rx timeout int pending +#define ISR_INT_RX_XOFF 0x10 // Rx Xoff int pending +#define ISR_INT_RTS_CTS 0x20 // RTS/CTS change int pending +#define ISR_FIFO_ENABLED 0xC0 // Bits set if FIFOs enabled +#define ISR_INT_BITS_MASK 0x3E // Mask to isolate valid int causes + + +#define LCR_BITS_5 0x00 // 5 bits/char +#define LCR_BITS_6 0x01 // 6 bits/char +#define LCR_BITS_7 0x02 // 7 bits/char +#define LCR_BITS_8 0x03 // 8 bits/char +#define LCR_BITS_MASK 0x03 // Mask for bits/char field + +#define LCR_STOP_1 0x00 // 1 stop bit +#define LCR_STOP_1_5 0x04 // 1.5 stop bits (if 5 bits/char) +#define LCR_STOP_2 0x04 // 2 stop bits (if 6-8 bits/char) +#define LCR_STOP_MASK 0x04 // Mask for stop bits field + +#define LCR_PAR_NONE 0x00 // No parity +#define LCR_PAR_ODD 0x08 // Odd parity +#define LCR_PAR_EVEN 0x18 // Even parity +#define LCR_PAR_MARK 0x28 // Force parity bit to 1 +#define LCR_PAR_SPACE 0x38 // Force parity bit to 0 +#define LCR_PAR_MASK 0x38 // Mask for parity field + +#define LCR_SET_BREAK 0x40 // Set Break condition +#define LCR_DL_ENABLE 0x80 // Enable access to divisor latch + +#define LCR_ACCESS_EFR 0xBF // Load this value to access DLL,DLM, + // and also the '654-only registers + // EFR, XON1, XON2, XOFF1, XOFF2 + + +#define MCR_DTR 0x01 // Assert DTR +#define MCR_RTS 0x02 // Assert RTS +#define MCR_OUT1 0x04 // Loopback only: Sets state of RI +#define MCR_MASTER_IE 0x08 // Enable interrupt outputs +#define MCR_LOOPBACK 0x10 // Set internal (digital) loopback mode +#define MCR_XON_ANY 0x20 // Enable any char to exit XOFF mode +#define MCR_IR_ENABLE 0x40 // Enable IrDA functions +#define MCR_BRG_DIV_4 0x80 // Divide baud rate clk by /4 instead of /1 + + +#define LSR_RX_AVAIL 0x01 // Rx data available +#define LSR_OVER_ERR 0x02 // Rx overrun +#define LSR_PAR_ERR 0x04 // Rx parity error +#define LSR_FRM_ERR 0x08 // Rx framing error +#define LSR_BREAK 0x10 // Rx break condition detected +#define LSR_TX_EMPTY 0x20 // Tx Fifo empty +#define LSR_TX_ALL_EMPTY 0x40 // Tx Fifo and shift register empty +#define LSR_FIFO_ERR 0x80 // Rx Fifo contains at least 1 erred char + + +#define MSR_DELTA_CTS 0x01 // CTS changed from last read +#define MSR_DELTA_DSR 0x02 // DSR changed from last read +#define MSR_DELTA_RI 0x04 // RI changed from 0 -> 1 +#define MSR_DELTA_CD 0x08 // CD changed from last read +#define MSR_CTS 0x10 // Current state of CTS +#define MSR_DSR 0x20 // Current state of DSR +#define MSR_RI 0x40 // Current state of RI +#define MSR_CD 0x80 // Current state of CD + + + + // Tx Rx + //------------------------------- +#define EFR_SWFC_NONE 0x00 // None None +#define EFR_SWFC_RX1 0x02 // None XOFF1 +#define EFR_SWFC_RX2 0x01 // None XOFF2 +#define EFR_SWFC_RX12 0x03 // None XOFF1 & XOFF2 +#define EFR_SWFC_TX1 0x08 // XOFF1 None +#define EFR_SWFC_TX1_RX1 0x0a // XOFF1 XOFF1 +#define EFR_SWFC_TX1_RX2 0x09 // XOFF1 XOFF2 +#define EFR_SWFC_TX1_RX12 0x0b // XOFF1 XOFF1 & XOFF2 +#define EFR_SWFC_TX2 0x04 // XOFF2 None +#define EFR_SWFC_TX2_RX1 0x06 // XOFF2 XOFF1 +#define EFR_SWFC_TX2_RX2 0x05 // XOFF2 XOFF2 +#define EFR_SWFC_TX2_RX12 0x07 // XOFF2 XOFF1 & XOFF2 +#define EFR_SWFC_TX12 0x0c // XOFF1 & XOFF2 None +#define EFR_SWFC_TX12_RX1 0x0e // XOFF1 & XOFF2 XOFF1 +#define EFR_SWFC_TX12_RX2 0x0d // XOFF1 & XOFF2 XOFF2 +#define EFR_SWFC_TX12_RX12 0x0f // XOFF1 & XOFF2 XOFF1 & XOFF2 + +#define EFR_TX_FC_MASK 0x0c // Mask to isolate Rx flow control +#define EFR_TX_FC_NONE 0x00 // No Tx Xon/Xoff flow control +#define EFR_TX_FC_X1 0x08 // Transmit Xon1/Xoff1 +#define EFR_TX_FC_X2 0x04 // Transmit Xon2/Xoff2 +#define EFR_TX_FC_X1_2 0x0c // Transmit Xon1&2/Xoff1&2 + +#define EFR_RX_FC_MASK 0x03 // Mask to isolate Rx flow control +#define EFR_RX_FC_NONE 0x00 // No Rx Xon/Xoff flow control +#define EFR_RX_FC_X1 0x02 // Receiver compares Xon1/Xoff1 +#define EFR_RX_FC_X2 0x01 // Receiver compares Xon2/Xoff2 +#define EFR_RX_FC_X1_2 0x03 // Receiver compares Xon1&2/Xoff1&2 + + +#define EFR_SWFC_MASK 0x0F // Mask for software flow control field +#define EFR_ENABLE_16654 0x10 // Enable 16C654 features +#define EFR_SPEC_DETECT 0x20 // Enable special character detect interrupt +#define EFR_AUTO_RTS 0x40 // Use RTS for Rx flow control +#define EFR_AUTO_CTS 0x80 // Use CTS for Tx flow control + +#endif // if !defined(_16654_H) + |