diff options
Diffstat (limited to 'include/linux/sbpcd.h')
| -rw-r--r-- | include/linux/sbpcd.h | 180 |
1 files changed, 136 insertions, 44 deletions
diff --git a/include/linux/sbpcd.h b/include/linux/sbpcd.h index ee7ec8d4c..e9021316d 100644 --- a/include/linux/sbpcd.h +++ b/include/linux/sbpcd.h @@ -5,22 +5,28 @@ /* * Attention! This file contains user-serviceable parts! * I recommend to make use of it... + * If you feel helpless, look into linux/Documentation/cdrom/sbpcd + * (good idea anyway, at least before mailing me). * * The definitions for the first controller can get overridden by * the kernel command line ("lilo boot option"). * Examples: + * sbpcd=0x300,LaserMate + * or * sbpcd=0x230,SoundBlaster * or - * sbpcd=0x300,LaserMate + * sbpcd=0x338,SoundScape * or - * sbpcd=0x330,SPEA + * sbpcd=0x2C0,Teac16bit * * If sbpcd gets used as a module, you can load it with - * insmod /usr/src/linux/modules/sbpcd.o sbpcd=0x230,1 + * insmod sbpcd.o sbpcd=0x300,0 * or - * insmod /usr/src/linux/modules/sbpcd.o sbpcd=0x300,0 + * insmod sbpcd.o sbpcd=0x230,1 * or - * insmod /usr/src/linux/modules/sbpcd.o sbpcd=0x330,2 + * insmod sbpcd.o sbpcd=0x338,2 + * or + * insmod sbpcd.o sbpcd=0x2C0,3 * respective to override the configured address and type. */ @@ -28,35 +34,36 @@ * define your CDROM port base address as CDROM_PORT * and specify the type of your interface card as SBPRO. * - * Read linux/drivers/block/README.sbpcd if you are in doubt about the - * type of your interface card (you should do that anyway). - * * address: * ======== * SBPRO type addresses typically are 0x0230 (=0x220+0x10), 0x0250, ... * LASERMATE type (CI-101P, WDH-7001C) addresses typically are 0x0300, ... - * SPEA addresses are from the LASERMATE type and range. + * SOUNDSCAPE addresses are from the LASERMATE type and range. You have to + * specify the REAL address here, not the configuration port address. Look + * at the CDROM driver's invoking line within your DOS CONFIG.SYS, or let + * sbpcd auto-probe, if you are not firm with the address. * There are some soundcards on the market with 0x0630, 0x0650, ...; their * type is not obvious (both types are possible). * * example: if your SBPRO audio address is 0x220, specify 0x230 and SBPRO 1. * if your soundcard has its CDROM port above 0x300, specify * that address and try SBPRO 0 first. + * if your SoundScape configuration port is at 0x330, specify + * 0x338 and SBPRO 2. * * interface type: * =============== * set SBPRO to 1 for "true" SoundBlaster card * set SBPRO to 0 for "compatible" soundcards and * for "poor" (no sound) interface cards. - * set SBPRO to 2 for the SPEA Media FX card + * set SBPRO to 2 for Ensonic SoundScape or SPEA Media FX cards + * set SBPRO to 3 for Teac 16bit interface cards * * Almost all "compatible" sound boards need to set SBPRO to 0. * If SBPRO is set wrong, the drives will get found - but any * data access will give errors (audio access will work). - * The "OmniCD" no-sound interface card from CreativeLabs needs SBPRO 1. - * - * mail to emoenke@gwdg.de if you have a "compatible" sound card which - * in fact needs to set SBPRO to 1 (not any known at time). + * The "OmniCD" no-sound interface card from CreativeLabs and most Teac + * interface cards need SBPRO 1. * * sound base: * =========== @@ -80,7 +87,7 @@ #define SOUND_BASE 0x000 /* <-----------<< sound address of this card or 0 */ #endif #if !(SBPCD_ISSUE-3) /* ===================== third interface board: === */ -#define CDROM_PORT 0x634 /* <-----------<< port address */ +#define CDROM_PORT 0x630 /* <-----------<< port address */ #define SBPRO 1 /* <-----------<< interface type */ #define MAX_DRIVES 4 /* set to 1 if the card does not use "drive select" */ #define SOUND_BASE 0x240 /* <-----------<< sound address of this card or 0 */ @@ -96,38 +103,85 @@ * some more or less user dependent definitions - service them! */ -/* Set this to 0 after you have configured your interface definitions right. */ +/* Set this to 0 once you have configured your interface definitions right. */ #define DISTRIBUTION 1 -/* max. number of audio frames to read with one */ -/* request (allocates n* 2352 bytes kernel memory!) */ -/* may be freely adjusted, f.e. 75 (= 1 sec.), at */ -/* runtime by use of the CDROMAUDIOBUFSIZ ioctl. */ -#define READ_AUDIO 0 +/* + * Time to wait after giving a message. + * This gets important if you enable non-standard DBG_xxx flags. + * You will see what happens if you omit the pause or make it + * too short. Be warned! + */ +#define KLOGD_PAUSE 1 -/* tray control: eject tray if no disk is in (0 or 1) */ +/* tray control: eject tray if no disk is in */ +#if DISTRIBUTION +#define JUKEBOX 0 +#else #define JUKEBOX 1 +#endif DISTRIBUTION -/* tray control: eject tray after last use (0 or 1) */ +/* tray control: eject tray after last use */ +#if DISTRIBUTION +#define EJECT 0 +#else #define EJECT 1 +#endif DISTRIBUTION + +/* max. number of audio frames to read with one */ +/* request (allocates n* 2352 bytes kernel memory!) */ +/* may be freely adjusted, f.e. 75 (= 1 sec.), at */ +/* runtime by use of the CDROMAUDIOBUFSIZ ioctl. */ +#define READ_AUDIO 0 + +/* Optimizations for the Teac CD-55A drive read performance. + * SBP_TEAC_SPEED can be changed here, or one can set the + * variable "teac" when loading as a module. + * Valid settings are: + * 0 - very slow - the recommended "DISTRIBUTION 1" setup. + * 1 - 2x performance with little overhead. No busy waiting. + * 2 - 4x performance with 5ms overhead per read. Busy wait. + * + * Setting SBP_TEAC_SPEED or the variable 'teac' to anything + * other than 0 may cause problems. If you run into them, first + * change SBP_TEAC_SPEED back to 0 and see if your drive responds + * normally. If yes, you are "allowed" to report your case - to help + * me with the driver, not to solve your hassle. Donīt mail if you + * simply are stuck into your own "tuning" experiments, you know? + */ +#define SBP_TEAC_SPEED 1 /*==========================================================================*/ /*==========================================================================*/ /* - * nothing to change below here if you are not experimenting + * nothing to change below here if you are not fully aware what you're doing */ #ifndef _LINUX_SBPCD_H #define _LINUX_SBPCD_H /*==========================================================================*/ /*==========================================================================*/ +/* + * driver's own read_ahead, data mode + */ +#define SBP_BUFFER_FRAMES 8 + #define LONG_TIMING 0 /* test against timeouts with "gold" CDs on CR-521 */ #undef FUTURE +#undef SAFE_MIXED #define TEST_UPC 0 #define SPEA_TEST 0 #define TEST_STI 0 +#define OLD_BUSY 0 #undef PATH_CHECK +#ifndef SOUND_BASE +#define SOUND_BASE 0 +#endif +#if DISTRIBUTION +#undef SBP_TEAC_SPEED +#define SBP_TEAC_SPEED 0 +#endif /*==========================================================================*/ /* * DDI interface definitions @@ -139,8 +193,6 @@ /* * "private" IOCTL functions */ -#define CDROMRESET 0x5380 /* hard-rest the drive */ -#define CDROMVOLREAD 0x5381 /* let the drive tell its volume settings */ #define CDROMAUDIOBUFSIZ 0x5382 /* set the audio buffer size */ /*==========================================================================*/ @@ -174,9 +226,9 @@ #define DBG_AUD 25 /* READ AUDIO debugging */ #define DBG_SEQ 26 /* Sequoia interface configuration trace */ #define DBG_LCS 27 /* Longshine LCS-7260 debugging trace */ -#define DBG_CD2 28 /* MKE CD200 debugging trace */ +#define DBG_CD2 28 /* MKE/Funai CD200 debugging trace */ #define DBG_TEA 29 /* TEAC CD-55A debugging trace */ -#define DBG_TE2 30 /* TEAC CD-55A 2nd debugging level */ +#define DBG_ECS 30 /* ECS-AT (Vertos 100) debugging trace */ #define DBG_000 31 /* unnecessary information */ /*==========================================================================*/ @@ -233,7 +285,7 @@ * LCS-7260 special status result bits: */ #define p_lcs_door_locked 0x02 -#define p_lcs_door_closed 0x01 +#define p_lcs_door_closed 0x01 /* probably disk_in */ /* * CR-52x special status result bits: @@ -263,6 +315,14 @@ #define pL_door_locked 0x02 #define pL_door_closed 0x01 +#define pV_door_closed 0x40 +#define pV_spinning 0x20 +#define pV_check 0x10 +#define pV_success 0x08 +#define pV_busy 0x04 +#define pV_door_locked 0x02 +#define pV_disk_ok 0x01 + #define p1_door_closed 0x80 #define p1_disk_in 0x40 #define p1_spinning 0x20 @@ -306,9 +366,9 @@ #define RESULT_READY ((inb(CDi_status)&s_not_result_ready)==0) /* - * drive types (firmware versions): + * drive families and types (firmware versions): */ -#define drv_fam0 0x08 /* CR-52x family */ +#define drv_fam0 0x0100 /* CR-52x family */ #define drv_199 (drv_fam0+0x01) /* <200 */ #define drv_200 (drv_fam0+0x02) /* <201 */ #define drv_201 (drv_fam0+0x03) /* <210 */ @@ -316,25 +376,35 @@ #define drv_211 (drv_fam0+0x05) /* <300 */ #define drv_300 (drv_fam0+0x06) /* >=300 */ -#define drv_famL 0x10 /* Longshine family */ +#define drv_fam1 0x0200 /* CR-56x family */ +#define drv_099 (drv_fam1+0x01) /* <100 */ +#define drv_100 (drv_fam1+0x02) /* >=100, only 1.02 and 5.00 known */ + +#define drv_fam2 0x0400 /* CD200 family */ + +#define drv_famT 0x0800 /* TEAC CD-55A */ + +#define drv_famL 0x1000 /* Longshine family */ #define drv_260 (drv_famL+0x01) /* LCS-7260 */ #define drv_e1 (drv_famL+0x01) /* LCS-7260, firmware "A E1" */ #define drv_f4 (drv_famL+0x02) /* LCS-7260, firmware "A4F4" */ -#define drv_fam1 0x20 /* CR-56x family */ -#define drv_099 (drv_fam1+0x01) /* <100 */ -#define drv_100 (drv_fam1+0x02) /* >=100, only 5.00 known here */ - -#define drv_famT 0x40 /* TEAC CD-55A */ -#define drv_fam2 0x80 /* CD200 family */ +#define drv_famV 0x2000 /* ECS-AT (vertos-100) family */ +#define drv_at (drv_famV+0x01) /* ECS-AT, firmware "1.00" */ #define fam0_drive (D_S[d].drv_type&drv_fam0) #define famL_drive (D_S[d].drv_type&drv_famL) +#define famV_drive (D_S[d].drv_type&drv_famV) #define fam1_drive (D_S[d].drv_type&drv_fam1) #define fam2_drive (D_S[d].drv_type&drv_fam2) #define famT_drive (D_S[d].drv_type&drv_famT) #define fam0L_drive (D_S[d].drv_type&(drv_fam0|drv_famL)) +#define fam0V_drive (D_S[d].drv_type&(drv_fam0|drv_famV)) +#define famLV_drive (D_S[d].drv_type&(drv_famL|drv_famV)) +#define fam0LV_drive (D_S[d].drv_type&(drv_fam0|drv_famL|drv_famV)) #define fam1L_drive (D_S[d].drv_type&(drv_fam1|drv_famL)) +#define fam1V_drive (D_S[d].drv_type&(drv_fam1|drv_famV)) +#define fam1LV_drive (D_S[d].drv_type&(drv_fam1|drv_famL|drv_famV)) #define fam01_drive (D_S[d].drv_type&(drv_fam0|drv_fam1)) #define fam12_drive (D_S[d].drv_type&(drv_fam1|drv_fam2)) #define fam2T_drive (D_S[d].drv_type&(drv_fam2|drv_famT)) @@ -378,7 +448,6 @@ #define audx13 0x0d /* Audio play operation successfully completed */ #define audx14 0x0e /* Audio play operation stopped due to error */ #define audx15 0x0f /* No current audio status to return */ - /* audio status (bcd) */ #define aud_11 0x11 /* Audio play operation in progress */ #define aud_12 0x12 /* Audio play operation paused */ @@ -386,7 +455,6 @@ #define aud_14 0x14 /* Audio play operation stopped due to error */ #define aud_15 0x15 /* No current audio status to return */ - /* * highest allowed drive number (MINOR+1) */ @@ -404,13 +472,15 @@ /*==========================================================================*/ +#define MIXER_addr SOUND_BASE+4 /* sound card's address register */ +#define MIXER_data SOUND_BASE+5 /* sound card's data register */ #define MIXER_CD_Volume 0x28 /* internal SB Pro register address */ /*==========================================================================*/ -/* - * Creative Labs Programmers did this: - */ -#define MAX_TRACKS 120 /* why more than 99? */ + +#define MAX_TRACKS 99 + +#define ERR_DISKCHANGE 615 /*==========================================================================*/ /* @@ -589,6 +659,7 @@ Read XA Parameter: * CD200: CMD2_ * LCS-7260: CMDL_ * TEAC CD-55A: CMDT_ + * ECS-AT: CMDV_ */ #define CMD1_RESET 0x0a #define CMD2_RESET 0x01 @@ -598,14 +669,17 @@ Read XA Parameter: #define CMD2_LOCK_CTL 0x1e #define CMDT_LOCK_CTL CMD2_LOCK_CTL #define CMDL_LOCK_CTL 0x0e +#define CMDV_LOCK_CTL CMDL_LOCK_CTL #define CMD1_TRAY_CTL 0x07 #define CMD2_TRAY_CTL 0x1b #define CMDT_TRAY_CTL CMD2_TRAY_CTL #define CMDL_TRAY_CTL 0x0d +#define CMDV_TRAY_CTL CMDL_TRAY_CTL #define CMD1_MULTISESS 0x8d #define CMDL_MULTISESS 0x8c +#define CMDV_MULTISESS CMDL_MULTISESS #define CMD1_SUBCHANINF 0x11 #define CMD2_SUBCHANINF 0x?? @@ -623,22 +697,27 @@ Read XA Parameter: #define CMD2_PATH_CHECK 0x??? #define CMDT_PATH_CHECK 0x??? #define CMDL_PATH_CHECK CMD0_PATH_CHECK +#define CMDV_PATH_CHECK CMD0_PATH_CHECK #define CMD0_SEEK 0x01 #define CMD1_SEEK CMD0_SEEK #define CMD2_SEEK 0x2b #define CMDT_SEEK CMD2_SEEK #define CMDL_SEEK CMD0_SEEK +#define CMDV_SEEK CMD0_SEEK #define CMD0_READ 0x02 #define CMD1_READ 0x10 #define CMD2_READ 0x28 #define CMDT_READ CMD2_READ #define CMDL_READ CMD0_READ +#define CMDV_READ CMD0_READ #define CMD0_READ_XA 0x03 #define CMD2_READ_XA 0xd4 +#define CMD2_READ_XA2 0xd5 #define CMDL_READ_XA CMD0_READ_XA /* really ?? */ +#define CMDV_READ_XA CMD0_READ_XA #define CMD0_READ_HEAD 0x04 @@ -646,11 +725,13 @@ Read XA Parameter: #define CMD1_SPINUP 0x02 #define CMD2_SPINUP CMD2_TRAY_CTL #define CMDL_SPINUP CMD0_SPINUP +#define CMDV_SPINUP CMD0_SPINUP #define CMD0_SPINDOWN 0x06 /* really??? */ #define CMD1_SPINDOWN 0x06 #define CMD2_SPINDOWN CMD2_TRAY_CTL #define CMDL_SPINDOWN 0x0d +#define CMDV_SPINDOWN CMD0_SPINDOWN #define CMD0_DIAG 0x07 @@ -658,6 +739,7 @@ Read XA Parameter: #define CMD1_READ_UPC 0x88 #define CMD2_READ_UPC 0x??? #define CMDL_READ_UPC CMD0_READ_UPC +#define CMDV_READ_UPC 0x8f #define CMD0_READ_ISRC 0x09 @@ -665,6 +747,7 @@ Read XA Parameter: #define CMD1_PLAY 0x??? #define CMD2_PLAY 0x??? #define CMDL_PLAY CMD0_PLAY +#define CMDV_PLAY CMD0_PLAY #define CMD0_PLAY_MSF 0x0b #define CMD1_PLAY_MSF 0x0e @@ -680,18 +763,22 @@ Read XA Parameter: #define CMD2_STATUS 0x00 #define CMDT_STATUS CMD2_STATUS #define CMDL_STATUS CMD0_STATUS +#define CMDV_STATUS CMD0_STATUS +#define CMD2_SEEK_LEADIN 0x00 #define CMD0_READ_ERR 0x82 #define CMD1_READ_ERR CMD0_READ_ERR #define CMD2_READ_ERR 0x03 #define CMDT_READ_ERR CMD2_READ_ERR /* get audio status */ #define CMDL_READ_ERR CMD0_READ_ERR +#define CMDV_READ_ERR CMD0_READ_ERR #define CMD0_READ_VER 0x83 #define CMD1_READ_VER CMD0_READ_VER #define CMD2_READ_VER 0x12 #define CMDT_READ_VER CMD2_READ_VER /* really ?? */ #define CMDL_READ_VER CMD0_READ_VER +#define CMDV_READ_VER CMD0_READ_VER #define CMD0_SETMODE 0x84 #define CMD1_SETMODE 0x09 @@ -719,6 +806,7 @@ Read XA Parameter: #define CMD2_READSUBQ 0x42 #define CMDT_READSUBQ CMD2_READSUBQ #define CMDL_READSUBQ CMD0_READSUBQ +#define CMDV_READSUBQ CMD0_READSUBQ #define CMD0_DISKCODE 0x8a @@ -727,22 +815,26 @@ Read XA Parameter: #define CMD2_DISKINFO 0x43 #define CMDT_DISKINFO CMD2_DISKINFO #define CMDL_DISKINFO CMD0_DISKINFO +#define CMDV_DISKINFO CMD0_DISKINFO #define CMD0_READTOC 0x8c #define CMD1_READTOC CMD0_READTOC #define CMD2_READTOC 0x??? #define CMDL_READTOC CMD0_READTOC +#define CMDV_READTOC CMD0_READTOC #define CMD0_PAU_RES 0x8d #define CMD1_PAU_RES 0x0d #define CMD2_PAU_RES 0x4b #define CMDT_PAUSE CMD2_PAU_RES #define CMDL_PAU_RES CMD0_PAU_RES +#define CMDV_PAUSE CMD0_PAU_RES #define CMD0_PACKET 0x8e #define CMD1_PACKET CMD0_PACKET #define CMD2_PACKET 0x??? #define CMDL_PACKET CMD0_PACKET +#define CMDV_PACKET 0x??? /*==========================================================================*/ /*==========================================================================*/ |