path: root/Documentation/specialix.txt

      specialix.txt  -- specialix IO8+ multiport serial driver readme.



      Copyright (C) 1997  Roger Wolff (R.E.Wolff@BitWizard.nl)

      Specialix pays for the development and support of this driver.
      Please DO contact io8-linux@specialix.co.uk if you require
      support.

      This driver was developed in the BitWizard linux device
      driver service. If you require a linux device driver for your
      product, please contact devices@BitWizard.nl for a quote.

      This code is firmly based on the riscom/8 serial driver,
      written by Dmitry Gorodchanin. The specialix IO8+ card
      programming information was obtained from the CL-CD1865 Data
      Book, and Specialix document number 6200059: IO8+ Hardware
      Functional Specification, augmented by document number 6200088:
      Merak Hardware Functional Specification. (IO8+/PCI is also 
      called Merak)


      This program is free software; you can redistribute it and/or
      modify it under the terms of the GNU General Public License as
      published by the Free Software Foundation; either version 2 of
      the License, or (at your option) any later version.

      This program is distributed in the hope that it will be
      useful, but WITHOUT ANY WARRANTY; without even the implied
      warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR
      PURPOSE.  See the GNU General Public License for more details.

      You should have received a copy of the GNU General Public
      License along with this program; if not, write to the Free
      Software Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139,
      USA.


Intro
=====

 
This file contains some random information, that I like to have online
instead of in a manual that can get lost. Ever misplace your Linux
kernel sources?  And the manual of one of the boards in your computer?


Addresses and interrupts
========================

Address dip switch settings:
The dip switch sets bits 2-9 of the IO address. 

       9 8 7 6 5 4 3 2 
     +-----------------+
   0 | X   X X X X X X |
     |                 |    =   IoBase = 0x100 
   1 |   X             |
     +-----------------+          ------ RS232 connectors ---->
         
         |    |    |
       edge connector
         |    |    |
         V    V    V

Base address 0x100 caused a conflict in one of my computers once.  I
haven't the foggiest why. My Specialix card is now at 0x180.  My
other computer runs just fine with the Specialix card at 0x100....
The card occupies 4 addresses, but actually only two are really used.

The PCI version doesn't have any dip switches. The BIOS assigns
an IO address. 

The driver now still autoprobes at 0x100, 0x180, 0x250 and 0x260.  If
that causes trouble for you, please report that. I'll remove
autoprobing then.

The driver will tell the card what IRQ to use, so you don't have to
change any jumpers to change the IRQ. Just use a command line
argument (irq=xx) to the insmod program to set the interrupt.

The BIOS assigns the IRQ on the PCI version. You have no say in what
IRQ to use in that case. 

If your specialix cards are not at the default locations, you can use
the kernel command line argument "specialix=io0,irq0,io1,irq1...".
Here "io0" is the io address for the first card, and "irq0" is the
irq line that the first card should use. And so on. 

Examples. 

You use the driver as a module and have three cards at 0x100, 0x250
and 0x180. And some way or another you want them detected in that
order. Moreover irq 12 is taken (e.g. by your PS/2 mouse).

  insmod specialix.o iobase=0x100,0x250,0x180 irq=9,11,15

The same three cards, but now in the kernel would require you to
add 

   specialix=0x100,9,0x250,11,0x180,15

to the command line. This would become 

   append="specialix=0x100,9,0x250,11,0x180,15" 

in your /etc/lilo.conf file if you use lilo. 

The Specialix driver is slightly odd: It allows you to have the second
or third card detected without having a first card. This has
advantages and disadvantages. A slot that isn't filled by an ISA card,
might be filled if a PCI card is detected. Thus if you have an ISA
card at 0x250 and a PCI card, you would get:

sx0: specialix IO8+ Board at 0x100 not found.
sx1: specialix IO8+ Board at 0x180 not found.
sx2: specialix IO8+ board detected at 0x250, IRQ 12, CD1865 Rev. B.
sx3: specialix IO8+ Board at 0x260 not found.
sx0: specialix IO8+ board detected at 0xd800, IRQ 9, CD1865 Rev. B.

This would happen if you don't give any probe hints to the driver. 
If you would specify:

   specialix=0x250,11

you'd get the following messages:

sx0: specialix IO8+ board detected at 0x250, IRQ 11, CD1865 Rev. B.
sx1: specialix IO8+ board detected at 0xd800, IRQ 9, CD1865 Rev. B.

ISA probing is aborted after the IO address you gave is exhausted, and
the PCI card is now detected as the second card. The ISA card is now
also forced to IRQ11....


Baud rates
==========

The rev 1.2 and below boards use a CL-CD1864. These chips can only 
do 64kbit. The rev 1.3 and newer boards use a CL-CD1865. These chips
are officially capable of 115k2.

The Specialix card uses a 25MHz crystal (in times two mode, which in
fact is a divided by two mode). This is not enough to reach the rated
115k2 on all ports at the same time. With this clock rate you can only
do 37% of this rate. This means that at 115k2 on all ports you are
going to lose characters (The chip cannot handle that many incoming
bits at this clock rate.) (Yes, you read that correctly: there is a
limit to the number of -=bits=- per second that the chip can handle.)

If you near the "limit" you will first start to see a graceful
degradation in that the chip cannot keep the transmitter busy at all
times. However with a central clock this slow, you can also get it to
miss incoming characters. The driver will print a warning message when
you are outside the official specs. The messages usually show up in
the file /var/log/messages .

The specialix card cannot reliably do 115k2. If you use it, you have
to do "extensive testing" (*) to verify if it actually works.

When "mgetty" communicates with my modem at 115k2 it reports:
got: +++[0d]ATQ0V1H0[0d][0d][8a]O[cb][0d][8a]
                            ^^^^ ^^^^    ^^^^ 

The three characters that have the "^^^" under them have suffered a
bit error in the highest bit. In conclusion: I've tested it, and found
that it simply DOESN'T work for me. I also suspect that this is also
caused by the baud rate being just a little bit out of tune. 

I upgraded the crystal to 66Mhz on one of my Specialix cards. Works
great! Contact me for details. (Voids warranty, requires a steady hand
and more such restrictions....)


(*) Cirrus logic CD1864 databook, page 40.


Cables for the Specialix IO8+
=============================

The pinout of the connectors on the IO8+ is:

     pin    short    direction    long name
            name
    Pin 1   DCD      input        Data Carrier Detect
    Pin 2   RXD      input        Receive
    Pin 3   DTR/RTS  output       Data Terminal Ready/Ready To Send
    Pin 4   GND      -            Ground
    Pin 5   TXD      output       Transmit
    Pin 6   CTS      input        Clear To Send
        
    
             -- 6  5  4  3  2  1 --
             |                    |
             |                    |
             |                    |
             |                    |
             +-----          -----+
                  |__________|
                      clip
    
    Front view of an RJ12 connector. Cable moves "into" the paper.
    (the plug is ready to plug into your mouth this way...)

    
    NULL cable. I don't know who is going to use these except for
    testing purposes, but I tested the cards with this cable. (It 
    took quite a while to figure out, so I'm not going to delete
    it. So there! :-)
    
    
    This end goes               This end needs
    straight into the           some twists in
    RJ12 plug.                  the wiring.
       IO8+ RJ12                   IO8+ RJ12
        1  DCD       white          -
        -             -             1 DCD
        2  RXD       black          5 TXD
        3  DTR/RTS   red            6 CTS
        4  GND       green          4 GND
        5  TXD       yellow         2 RXD
        6  CTS       blue           3 DTR/RTS
    

    Same NULL cable, but now sorted on the second column.
 
        1  DCD       white          -
        -             -             1 DCD
        5  TXD       yellow         2 RXD
        6  CTS       blue           3 DTR/RTS
        4  GND       green          4 GND
        2  RXD       black          5 TXD
        3  DTR/RTS   red            6 CTS
    
    
    
    This is a modem cable usable for hardware handshaking:
        RJ12                        DB25           DB9
        1   DCD      white          8 DCD          1 DCD
        2   RXD      black          3 RXD          2 RXD
        3   DTR/RTS  red            4 RTS          7 RTS
        4   GND      green          7 GND          5 GND
        5   TXD      yellow         2 TXD          3 TXD
        6   CTS      blue           5 CTS          8 CTS
                            +----   6 DSR          6 DSR
                            +----  20 DTR          4 DTR

    This is a modem cable usable for software handshaking:
    It allows you to reset the modem using the DTR ioctls.
    I (REW) have never tested this, "but xxxxxxxxxxxxx
    says that it works." If you test this, please
    tell me and I'll fill in your name on the xxx's.

        RJ12                        DB25           DB9
        1   DCD      white          8 DCD          1 DCD
        2   RXD      black          3 RXD          2 RXD
        3   DTR/RTS  red           20 DTR          4 DTR
        4   GND      green          7 GND          5 GND
        5   TXD      yellow         2 TXD          3 TXD
        6   CTS      blue           5 CTS          8 CTS
                            +----   6 DSR          6 DSR
                            +----   4 RTS          7 RTS

   I bought a 6 wire flat cable. It was colored as indicated.
   Check that yours is the same before you trust me on this.
   
 
Hardware handshaking issues.
============================

The driver can be compiled in two different ways. The default
("Specialix DTR/RTS pin is RTS" is off) the pin behaves as DTR when
hardware handshaking is off. It behaves as the RTS hardware
handshaking signal when hardware handshaking is selected.

When you use this, you have to use the appropriate cable. The
cable will either be compatible with hardware handshaking or with
software handshaking. So switching on the fly is not really an
option.

I actually prefer to use the "Specialix DTR/RTS pin is RTS" option.
This makes the DTR/RTS pin always an RTS pin, and ioctls to
change DTR are always ignored. I have a cable that is configured
for this. 


Ports and devices
=================

Port 0 is the one furthest from the card-edge connector.

Devices:

You should make the devices as follows:

bash
cd /dev
for i in  0  1  2  3  4  5  6  7  8  9 10 11 12 13 14 15 \
         16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
do
  echo -n "$i "
  mknod /dev/ttyW$i c 75 $i
  mknod /dev/cuw$i c 76 $i
done
echo ""

If your system doesn't come with these devices preinstalled, bug your
linux-vendor about this. They have had ample time to get this
implemented by now.

You cannot have more than 4 boards in one computer. The card only
supports 4 different interrupts. If you really want this, contact me
about this and I'll give you a few tips (requires soldering iron)....

If you have enough PCI slots, you can probably use more than 4 PCI
versions of the card though.... 

The PCI version of the card cannot adhere to the mechanical part of
the PCI spec because the 8 serial connectors are simply too large. If
it doesn't fit in your computer, bring back the card.


------------------------------------------------------------------------


  Fixed bugs and restrictions:
       - During intialization, interrupts are blindly turned on.
            Having a shadow variable would cause an extra memory
            access on every IO instruction. 
       - The interrupt (on the card) should be disabled when we
         don't allocate the Linux end of the interrupt. This allows 
         a different driver/card to use it while all ports are not in
         use..... (a la standard serial port)
       == An extra _off variant of the sx_in and sx_out macros are
          now available. They don't set the interrupt enable bit.
          These are used during initialization. Normal operation uses
          the old variant which enables the interrupt line.
       - RTS/DTR issue needs to be implemented according to 
         specialix' spec.
            I kind of like the "determinism" of the current 
            implementation. Compile time flag?
       == Ok. Compile time flag! Default is how Specialix likes it.
       == Now a config time flag! Gets saved in your config file. Neat!
       - Can you set the IO address from the lilo command line?
            If you need this, bug me about it, I'll make it. 
       == Hah! No bugging needed. Fixed! :-)
       - Cirrus logic hasn't gotten back to me yet why the CD1865 can
            and the CD1864 can't do 115k2. I suspect that this is
            because the CD1864 is not rated for 33MHz operation.
            Therefore the CD1864 versions of the card can't do 115k2 on 
            all ports just like the CD1865 versions. The driver does
            not block 115k2 on CD1864 cards. 
        == I called the Cirrus Logic representative here in Holland.
           The CD1864 databook is identical to the CD1865 databook, 
           except for an extra warning at the end. Similar Bit errors
           have been observed in testing at 115k2 on both an 1865 and
           a 1864 chip. I see no reason why I would prohibit 115k2 on
           1864 chips and not do it on 1865 chips. Actually there is
           reason to prohibit it on BOTH chips. I print a warning.
           If you use 115k2, you're on your own. 
       - A spiky CD may send spurious HUPs. Also in CLOCAL???
         -- A fix for this turned out to be counter productive. 
            Different fix? Current behaviour is acceptable?
         -- Maybe the current implementation is correct. If anybody
            gets bitten by this, please report, and it will get fixed.

         -- Testing revealed that when in CLOCAL, the problem doesn't
            occur. As warned for in the CD1865 manual, the chip may
            send modem intr's on a spike. We could filter those out,
            but that would be a cludge anyway (You'd still risk getting
            a spurious HUP when two spikes occur.).....
 


  Bugs & restrictions:
       - This is a difficult card to autoprobe.
            You have to WRITE to the address register to even 
            read-probe a CD186x register. Disable autodetection?
         -- Specialix: any suggestions?
       - Arbitrary baud rates are not implemented yet. 
            If you need this, bug me about it.