1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
|
#define DMA_BUFF_SIZE 2200
/* Network statistics, with the same names as 'struct enet_statistics'. */
#define netstats enet_statistics
#define ON 1
#define OFF 0
/* Register offset info, specific to the PI
* E.g., to read the data port on channel A, use
* inportb(pichan[dev].base + CHANA + DATA)
*/
#define CHANB 0 /* Base of channel B regs */
#define CHANA 2 /* Base of channel A regs */
/* 8530 ports on each channel */
#define CTL 0
#define DATA 1
#define DMAEN 0x4 /* Offset off DMA Enable register */
/* Timer chip offsets */
#define TMR0 0x8 /* Offset of timer 0 register */
#define TMR1 0x9 /* Offset of timer 1 register */
#define TMR2 0xA /* Offset of timer 2 register */
#define TMRCMD 0xB /* Offset of timer command register */
/* Timer chip equates */
#define SC0 0x00 /* Select counter 0 */
#define SC1 0x40 /* Select counter 1 */
#define SC2 0x80 /* Select counter 2 */
#define CLATCH 0x00 /* Counter latching operation */
#define MSB 0x20 /* Read/load MSB only */
#define LSB 0x10 /* Read/load LSB only */
#define LSB_MSB 0x30 /* Read/load LSB, then MSB */
#define MODE0 0x00 /* Interrupt on terminal count */
#define MODE1 0x02 /* Programmable one shot */
#define MODE2 0x04 /* Rate generator */
#define MODE3 0x06 /* Square wave rate generator */
#define MODE4 0x08 /* Software triggered strobe */
#define MODE5 0x0a /* Hardware triggered strobe */
#define BCD 0x01 /* BCD counter */
/* DMA controller registers */
#define DMA_STAT 8 /* DMA controller status register */
#define DMA_CMD 8 /* DMA controller command register */
#define DMA_MASK 10 /* DMA controller mask register */
#define DMA_MODE 11 /* DMA controller mode register */
#define DMA_RESETFF 12 /* DMA controller first/last flip flop */
/* DMA data */
#define DMA_DISABLE (0x04) /* Disable channel n */
#define DMA_ENABLE (0x00) /* Enable channel n */
/* Single transfers, incr. address, auto init, writes, ch. n */
#define DMA_RX_MODE (0x54)
/* Single transfers, incr. address, no auto init, reads, ch. n */
#define DMA_TX_MODE (0x48)
#define SINGLE 3686400
#define DOUBLE 7372800
#define SIOCGPIPARAM 0x5000 /* get PI parameters */
#define SIOCSPIPARAM 0x5001 /* set */
#define SIOCGPIBAUD 0x5002 /* get only baud rate */
#define SIOCSPIBAUD 0x5003
#define SIOCGPIDMA 0x5004 /* get only DMA */
#define SIOCSPIDMA 0x5005
#define SIOCGPIIRQ 0x5006 /* get only IRQ */
#define SIOCSPIIRQ 0x5007
struct pi_req {
int cmd;
int speed;
int clockmode;
int txdelay;
unsigned char persist;
int slotime;
int squeldelay;
int dmachan;
int irq;
};
#ifdef __KERNEL__
/* Information that needs to be kept for each channel. */
struct pi_local {
struct netstats stats; /* %%%dp*/
long open_time; /* Useless example local info. */
unsigned long xtal;
struct mbuf *rcvbuf;/* Buffer for current rx packet */
struct mbuf *rxdmabuf1; /* DMA rx buffer */
struct mbuf *rxdmabuf2; /* DMA rx buffer */
int bufsiz; /* Size of rcvbuf */
char *rcp; /* Pointer into rcvbuf */
struct sk_buff_head sndq; /* Packets awaiting transmission */
int sndcnt; /* Number of packets on sndq */
struct sk_buff *sndbuf; /* Current buffer being transmitted */
char *txdmabuf; /* Transmit DMA buffer */
char *txptr; /* Used by B port tx */
int txcnt;
char tstate; /* Transmitter state */
#define IDLE 0 /* Transmitter off, no data pending */
#define ACTIVE 1 /* Transmitter on, sending data */
#define UNDERRUN 2 /* Transmitter on, flushing CRC */
#define FLAGOUT 3 /* CRC sent - attempt to start next frame */
#define DEFER 4 /* Receive Active - DEFER Transmit */
#define ST_TXDELAY 5 /* Sending leading flags */
#define CRCOUT 6
char rstate; /* Set when !DCD goes to 0 (TRUE) */
/* Normal state is ACTIVE if Receive enabled */
#define RXERROR 2 /* Error -- Aborting current Frame */
#define RXABORT 3 /* ABORT sequence detected */
#define TOOBIG 4 /* too large a frame to store */
int dev; /* Device number */
int base; /* Base of I/O registers */
int cardbase; /* Base address of card */
int stata; /* address of Channel A status regs */
int statb; /* address of Channel B status regs */
int speed; /* Line speed, bps */
int clockmode; /* tapr 9600 modem clocking option */
int txdelay; /* Transmit Delay 10 ms/cnt */
unsigned char persist; /* Persistence (0-255) as a % */
int slotime; /* Delay to wait on persistence hit */
int squeldelay; /* Delay after XMTR OFF for squelch tail */
struct iface *iface; /* Associated interface */
int dmachan; /* DMA channel for this port */
};
#endif
|
