path: root/drivers/scsi/advansys.c

/* $Id: advansys.c,v 1997/05/28 00:06:55 bobf Exp bobf $ */
#define ASC_VERSION "2.8"    /* AdvanSys Driver Version */

/*
 * advansys.c - Linux Host Driver for AdvanSys SCSI Adapters
 * 
 * Copyright (c) 1995-1997 Advanced System Products, Inc.
 * All Rights Reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that redistributions of source
 * code retain the above copyright notice and this comment without
 * modification.
 *
 * There is an AdvanSys Linux WWW page at:
 *  http://www.advansys.com/linux.html
 *
 * The latest version of the AdvanSys driver is available at:
 *  ftp://ftp.advansys.com/pub/linux
 *
 * Please send questions, comments, bug reports to:
 * bobf@advansys.com (Bob Frey)
 */


/*

  Documentation for the AdvanSys Driver

  A. Linux Kernel Testing
  B. Adapters Supported by this Driver
  C. Linux v1.2.X - Directions for Adding the AdvanSys Driver
  D. Linux v1.3.1 - v1.3.57 - Directions for Adding the AdvanSys Driver
  E. Linux v1.3.58 and Newer - Upgrading the AdvanSys Driver
  F. Source Comments
  G. Driver Compile Time Options and Debugging
  H. Driver LILO Option
  I. Release History
  J. Known Problems or Issues
  K. Credits
  L. AdvanSys Contact Information

  A. Linux Kernel Testing

     This driver has been tested in the following Linux kernels: v1.2.13,
     v1.3.57, v2.0.30, v2.1.40. These kernel versions are major releases
     of Linux or the latest Linux kernel versions available when this version
     of the driver was released. The driver should also work in earlier
     versions of the Linux kernel. Beginning with v1.3.58 the AdvanSys driver
     is included with all Linux kernels. Please refer to sections C, D, and
     E for instructions on adding or upgrading the AdvanSys driver.

  B. Adapters Supported by this Driver
 
     AdvanSys (Advanced System Products, Inc.) manufactures the following
     Bus-Mastering SCSI-2 Host Adapters for the ISA, EISA, VL, and PCI
     buses. This Linux driver supports all of these adapters.
     
     The CDB counts below indicate the number of SCSI CDB (Command
     Descriptor Block) requests that can be stored in the RISC chip
     cache and board LRAM. A CDB is a single SCSI command. The driver
     detect routine will display the number of CDBs available for each
     adapter detected. The number of CDBs used by the driver can be
     lowered in the BIOS by changing the 'Host Queue Size' adapter setting.

     Connectivity Products:
        ABP510/5150 - Bus-Master ISA (240 CDB) (Footnote 1)
        ABP5140 - Bus-Master ISA PnP (16 CDB) (Footnote 1, 3)
        ABP5142 - Bus-Master ISA PnP with floppy (16 CDB) (Footnote 4)
        ABP920 - Bus-Master PCI (16 CDB)
        ABP930 - Bus-Master PCI (16 CDB) (Footnote 5)
        ABP930U - Bus-Master PCI Ultra (16 CDB)
        ABP930UA - Bus-Master PCI Ultra (16 CDB)
        ABP960 - Bus-Master PCI MAC/PC (16 CDB) (Footnote 2)
        ABP960U - Bus-Master PCI MAC/PC Ultra (16 CDB)
     
     Single Channel Products:
        ABP542 - Bus-Master ISA with floppy (240 CDB)
        ABP742 - Bus-Master EISA (240 CDB)
        ABP842 - Bus-Master VL (240 CDB)
        ABP940 - Bus-Master PCI (240 CDB)
        ABP940U - Bus-Master PCI Ultra (240 CDB)
        ABP970 - Bus-Master PCI MAC/PC (240 CDB)
        ABP970U - Bus-Master PCI MAC/PC Ultra (240 CDB)
     
     Dual Channel Products:
        ABP752 - Dual Channel Bus-Master EISA (240 CDB Per Channel)
        ABP852 - Dual Channel Bus-Master VL (240 CDB Per Channel)
        ABP950 - Dual Channel Bus-Master PCI (240 CDB Per Channel)
     
     Footnotes:
       1. This board has been shipped by HP with the 4020i CD-R drive.
          The board has no BIOS so it cannot control a boot device, but
          it can control any secondary SCSI device.
       2. This board has been sold by Iomega as a Jaz Jet PCI adapter.
       3. This board has been sold by SIIG as the i540 SpeedMaster.
       4. This board has been sold by SIIG as the i542 SpeedMaster.
       5. This board has been sold by SIIG as the Fast SCSI Pro PCI.

  C. Linux v1.2.X - Directions for Adding the AdvanSys Driver

     These directions apply to v1.2.13. For versions that follow v1.2.13.
     but precede v1.3.57 some of the changes for Linux v1.3.X listed
     below may need to be modified or included. A patch is available
     for v1.2.13 from the AdvanSys WWW and FTP sites.
 
     There are two source files: advansys.h and advansys.c. Copy
     both of these files to the directory /usr/src/linux/drivers/scsi.
    
     1. Add the following line to /usr/src/linux/arch/i386/config.in
        after "comment 'SCSI low-level drivers'":
    
          bool 'AdvanSys SCSI support' CONFIG_SCSI_ADVANSYS y
    
     2. Add the following lines to /usr/src/linux/drivers/scsi/hosts.c
        after "#include "hosts.h"":
    
          #ifdef CONFIG_SCSI_ADVANSYS
          #include "advansys.h"
          #endif
    
        and after "static Scsi_Host_Template builtin_scsi_hosts[] =":
    
          #ifdef CONFIG_SCSI_ADVANSYS
          ADVANSYS,
          #endif
    
     3. Add the following lines to /usr/src/linux/drivers/scsi/Makefile:
    
          ifdef CONFIG_SCSI_ADVANSYS
          SCSI_SRCS := $(SCSI_SRCS) advansys.c
          SCSI_OBJS := $(SCSI_OBJS) advansys.o
          else
          SCSI_MODULE_OBJS := $(SCSI_MODULE_OBJS) advansys.o
          endif

     4. (Optional) If you would like to enable the LILO command line
        and /etc/lilo.conf 'advansys' option, make the following changes.
        This option can be used to disable I/O port scanning or to limit
        I/O port scanning to specific addresses. Refer to the 'Driver
        LILO Option' section below. Add the following lines to
        /usr/src/linux/init/main.c in the prototype section:

          extern void advansys_setup(char *str, int *ints);

        and add the following lines to the bootsetups[] array.

          #ifdef CONFIG_SCSI_ADVANSYS
             { "advansys=", advansys_setup },
          #endif

     5. If you have the HP 4020i CD-R driver and Linux v1.2.X you should
        add a fix to the CD-ROM target driver. This fix will allow
        you to mount CDs with the iso9660 file system. Linux v1.3.X
        already has this fix. In the file /usr/src/linux/drivers/scsi/sr.c
        and function get_sectorsize() after the line:

        if(scsi_CDs[i].sector_size == 0) scsi_CDs[i].sector_size = 2048;

        add the following line:

        if(scsi_CDs[i].sector_size == 2340) scsi_CDs[i].sector_size = 2048;

     6. In the directory /usr/src/linux run 'make config' to configure
        the AdvanSys driver, then run 'make vmlinux' or 'make zlilo' to
        make the kernel. If the AdvanSys driver is not configured, then
        a loadable module can be built by running 'make modules' and
        'make modules_install'. Use 'insmod' and 'rmmod' to install
        and remove advansys.o.
 
  D. Linux v1.3.1 - v1.3.57 - Directions for Adding the AdvanSys Driver

     These directions apply to v1.3.57. For versions that precede v1.3.57
     some of these changes may need to be modified or eliminated. A patch
     is available for v1.3.57 from the AdvanSys WWW and FTP sites.
     Beginning with v1.3.58 this driver is included with the Linux
     distribution eliminating the need for making any changes.

     There are two source files: advansys.h and advansys.c. Copy
     both of these files to the directory /usr/src/linux/drivers/scsi.
   
     1. Add the following line to /usr/src/linux/drivers/scsi/Config.in
        after "comment 'SCSI low-level drivers'":
   
          dep_tristate 'AdvanSys SCSI support' CONFIG_SCSI_ADVANSYS $CONFIG_SCSI
   
     2. Add the following lines to /usr/src/linux/drivers/scsi/hosts.c
        after "#include "hosts.h"":
   
          #ifdef CONFIG_SCSI_ADVANSYS
          #include "advansys.h"
          #endif
   
        and after "static Scsi_Host_Template builtin_scsi_hosts[] =":
   
          #ifdef CONFIG_SCSI_ADVANSYS
          ADVANSYS,
          #endif
   
     3. Add the following lines to /usr/src/linux/drivers/scsi/Makefile:
   
          ifeq ($(CONFIG_SCSI_ADVANSYS),y)
          L_OBJS += advansys.o
          else
            ifeq ($(CONFIG_SCSI_ADVANSYS),m)
            M_OBJS += advansys.o
            endif
          endif
   
     4. Add the following line to /usr/src/linux/include/linux/proc_fs.h
        in the enum scsi_directory_inos array:
   
          PROC_SCSI_ADVANSYS,
   
     5. (Optional) If you would like to enable the LILO command line
        and /etc/lilo.conf 'advansys' option, make the following changes.
        This option can be used to disable I/O port scanning or to limit
        I/O port scanning to specific addresses. Refer to the 'Driver
        LILO Option' section below. Add the following lines to
        /usr/src/linux/init/main.c in the prototype section:
   
          extern void advansys_setup(char *str, int *ints);
   
        and add the following lines to the bootsetups[] array.
   
          #ifdef CONFIG_SCSI_ADVANSYS
             { "advansys=", advansys_setup },
          #endif
   
     6. In the directory /usr/src/linux run 'make config' to configure
        the AdvanSys driver, then run 'make vmlinux' or 'make zlilo' to
        make the kernel. If the AdvanSys driver is not configured, then
        a loadable module can be built by running 'make modules' and
        'make modules_install'. Use 'insmod' and 'rmmod' to install
        and remove advansys.o.

  E. Linux v1.3.58 and Newer - Upgrading the AdvanSys Driver

     To upgrade the AdvanSys driver in a Linux v1.3.58 and newer
     kernel, first check the version of the current driver. The
     version is defined by the manifest constant ASC_VERSION at
     the beginning of advansys.c. The new driver should have a
     ASC_VERSION value greater than the current version. To install
     the new driver rename advansys.c and advansys.h in the Linux
     kernel source tree drivers/scsi directory to different names
     or save them to a different directory in case you want to revert
     to the old version of the driver. After the old driver is saved
     copy the new advansys.c and advansys.h to drivers/scsi, rebuild
     the kernel, and install the new kernel. No other changes are needed.

  F. Source Comments
 
     1. Use tab stops set to 4 for the source files. For vi use 'se tabstops=4'.
 
     2. This driver should be maintained in multiple files. But to make
        it easier to include with Linux and to follow Linux conventions,
        the whole driver is maintained in the source files advansys.h and
        advansys.c. In this file logical sections of the driver begin with
        a comment that contains '---'. The following are the logical sections
        of the driver below.
 
           --- Linux Version
           --- Linux Include Files 
           --- Driver Options
           --- Debugging Header
           --- Asc Library Constants and Macros
           --- Driver Constants and Macros
           --- Driver Structures
           --- Driver Data
           --- Driver Function Prototypes
           --- Linux 'Scsi_Host_Template' and advansys_setup() Functions
           --- Loadable Driver Support
           --- Miscellaneous Driver Functions
           --- Functions Required by the Asc Library
           --- Tracing and Debugging Functions
           --- Asc Library Functions
 
     3. The string 'XXX' is used to flag code that needs to be re-written
        or that contains a problem that needs to be addressed.
 
     4. I have stripped comments from and reformatted the source for the
        Asc Library which is included in this file. I haven't done this
        to obfuscate the code. Actually I have done this to deobfuscate
        the code. The Asc Library source can be found under the following
        headings.
 
           --- Asc Library Constants and Macros
           --- Asc Library Functions
 
  G. Driver Compile Time Options and Debugging
 
     In this source file the following constants can be defined. They are
     defined in the source below. Both of these options are enabled by
     default.
 
     1. ADVANSYS_ASSERT - Enable driver assertions (Def: Enabled)

        Enabling this option adds assertion logic statements to the
        driver. If an assertion fails a message will be displayed to
        the console, but the system will continue to operate. Any
        assertions encountered should be reported to the person
        responsible for the driver. Assertion statements may proactively
        detect problems with the driver and facilitate fixing these
        problems. Enabling assertions will add a small overhead to the
        execution of the driver.

     2. ADVANSYS_DEBUG - Enable driver debugging (Def: Disabled)

        Enabling this option adds tracing functions to the driver and
        the ability to set a driver tracing level at boot time. This
        option will also symbols not required outside the driver to
        the kernel name space. This option is very useful for debugging
        the driver, but it will add to the size of the driver execution
        image and add overhead to the execution of the driver.
 
        The amount of debugging output can be controlled with the global
        variable 'asc_dbglvl'. The higher the number the more output. By
        default the debug level is 0.
        
        If the driver is loaded at boot time and the LILO Driver Option
        is included in the system, the debug level can be changed by
        specifying a 5th (ASC_NUM_BOARD_SUPPORTED + 1) I/O Port. The
        first three hex digits of the pseudo I/O Port must be set to
        'deb' and the fourth hex digit specifies the debug level: 0 - F.
        The following command line will look for an adapter at 0x330
        and set the debug level to 2.

           linux advansys=0x330,0,0,0,0xdeb2

        If the driver is built as a loadable module this variable can be
        defined when the driver is loaded. The following insmod command
        will set the debug level to one.
  
           insmod advansys.o asc_dbglvl=1
 
        Debugging Message Levels:
           0: Errors Only
           1: High-Level Tracing
           2-N: Verbose Tracing
 
        I don't know the approved way for turning on printk()s to the
        console. Here's a program I use to do this. Debug output is
        logged in /var/adm/messages.
 
          main()
          {
                  syscall(103, 7, 0, 0);
          }
 
        I found that increasing LOG_BUF_LEN to 40960 in kernel/printk.c
        prevents most level 1 debug messages from being lost.

        this constant for debugging purposes, but for normal use of
        the driver the constant should not be defined. This option
        does not add overhead to the driver, but it does add unnecessary
        symbols to the kernel name space.
 
     3. ADVANSYS_STATS - Enable statistics (Def: Enabled >= v1.3.0)
 
        Enabling this option adds statistics collection and display
        through /proc to the driver. The information is useful for
        monitoring driver and device performance. It will add to the
        size of the driver execution image and add minor overhead to
        the execution of the driver.

        Statistics are maintained on a per adapter basis. Driver entry
        point call counts and transfer size counts are maintained.
        Statistics are only available for kernels greater than or equal
        to v1.3.0 with the CONFIG_PROC_FS (/proc) file system configured.

        AdvanSys SCSI adapter files have the following path name format:

           /proc/scsi/advansys/[0-(ASC_NUM_BOARD_SUPPORTED-1)]

        This information can be displayed with cat. For example:

           cat /proc/scsi/advansys/0

        When ADVANSYS_STATS is not defined the AdvanSys /proc files only
        contain adapter and device configuration information.


  H. Driver LILO Option
 
     If init/main.c is modified as described in the 'Directions for Adding
     the AdvanSys Driver to Linux' section (B.4.) above, the driver will
     recognize the 'advansys' LILO command line and /etc/lilo.conf option.
     This option can be used to either disable I/O port scanning or to limit
     scanning to 1 - 4 I/O ports. Regardless of the option setting EISA and
     PCI boards will still be searched for and detected. This option only
     affects searching for ISA and VL boards.

     Examples:
       1. Eliminate I/O port scanning:
            boot: linux advansys=
              or
            boot: linux advansys=0x0
       2. Limit I/O port scanning to one I/O port:
            boot: linux advansys=0x110
       3. Limit I/O port scanning to four I/O ports:
            boot: linux advansys=0x110,0x210,0x230,0x330

     For a loadable module the same effect can be achieved by setting
     the 'asc_iopflag' variable and 'asc_ioport' array when loading
     the driver, e.g.

           insmod advansys.o asc_iopflag=1 asc_ioport=0x110,0x330

     If ADVANSYS_DEBUG is defined a 5th (ASC_NUM_BOARD_SUPPORTED + 1)
     I/O Port may be added to specify the driver debug level. Refer to
     the 'Driver Compile Time Options and Debugging' section above for
     more information.

  I. Release History

     BETA-1.0 (12/23/95): 
         First Release

     BETA-1.1 (12/28/95):
         1. Prevent advansys_detect() from being called twice.
         2. Add LILO 0xdeb[0-f] option to set 'asc_dbglvl'.

     1.2 (1/12/96):
         1. Prevent re-entrancy in the interrupt handler which
            resulted in the driver hanging Linux.
         2. Fix problem that prevented ABP-940 cards from being
            recognized on some PCI motherboards.
         3. Add support for the ABP-5140 PnP ISA card.
         4. Fix check condition return status.
         5. Add conditionally compiled code for Linux v1.3.X.

     1.3 (2/23/96):
         1. Fix problem in advansys_biosparam() that resulted in the
            wrong drive geometry being returned for drives > 1GB with
            extended translation enabled.
         2. Add additional tracing during device initialization.
         3. Change code that only applies to ISA PnP adapter.
         4. Eliminate 'make dep' warning.
         5. Try to fix problem with handling resets by increasing their
            timeout value.

     1.4 (5/8/96):
         1. Change definitions to eliminate conflicts with other subsystems.
         2. Add versioning code for the shared interrupt changes.
         3. Eliminate problem in asc_rmqueue() with iterating after removing
            a request.
         4. Remove reset request loop problem from the "Known Problems or
            Issues" section. This problem was isolated and fixed in the
            mid-level SCSI driver.
        
     1.5 (8/8/96):
         1. Add support for ABP-940U (PCI Ultra) adapter.
         2. Add support for IRQ sharing by setting the SA_SHIRQ flag for
            request_irq and supplying a dev_id pointer to both request_irq()
            and free_irq().
         3. In AscSearchIOPortAddr11() restore a call to check_region() which
            should be used before I/O port probing.
         4. Fix bug in asc_prt_hex() which resulted in the displaying
            the wrong data.
         5. Incorporate miscellaneous Asc Library bug fixes and new microcode.
         6. Change driver versioning to be specific to each Linux sub-level.
         7. Change statistics gathering to be per adapter instead of global
            to the driver.
         8. Add more information and statistics to the adapter /proc file:
            /proc/scsi/advansys[0...].
         9. Remove 'cmd_per_lun' from the "Known Problems or Issues" list.
            This problem has been addressed with the SCSI mid-level changes
            made in v1.3.89. The advansys_select_queue_depths() function
            was added for the v1.3.89 changes.

     1.6 (9/10/96):
         1. Incorporate miscellaneous Asc Library bug fixes and new microcode.

     1.7 (9/25/96):
         1. Enable clustering and optimize the setting of the maximum number
            of scatter gather elements for any particular board. Clustering
            increases CPU utilization, but results in a relatively larger
            increase in I/O throughput.
         2. Improve the performance of the request queuing functions by
            adding a last pointer to the queue structure.
         3. Correct problems with reset and abort request handling that
            could have hung or crashed Linux.
         4. Add more information to the adapter /proc file:
            /proc/scsi/advansys[0...].
         5. Remove the request timeout issue form the driver issues list.
         6. Miscellaneous documentation additions and changes.

     1.8 (10/4/96):
         1. Make changes to handle the new v2.1.0 kernel memory mapping
            in which a kernel virtual address may not be equivalent to its
            bus or DMA memory address.
         2. Change abort and reset request handling to make it yet even
            more robust.
         3. Try to mitigate request starvation by sending ordered requests
            to heavily loaded, tag queuing enabled devices.
         4. Maintain statistics on request response time.
         5. Add request response time statistics and other information to
            the adapter /proc file: /proc/scsi/advansys[0...].

     1.9 (10/21/96):
         1. Add conditionally compiled code (ASC_QUEUE_FLOW_CONTROL) to
            make use of mid-level SCSI driver device queue depth flow
            control mechanism. This will eliminate aborts caused by a
            device being unable to keep up with requests and eliminate
            repeat busy or QUEUE FULL status returned by a device.
         2. Incorporate miscellaneous Asc Library bug fixes.
         3. To allow the driver to work in kernels with broken module
            support set 'cmd_per_lun' if the driver is compile as a
            module. This change affects kernels v1.3.89 to present.
         4. Remove PCI BIOS address from the driver banner. The PCI BIOS
            is relocated by the motherboard BIOS and its new address can
            not be determined by the driver.
         5. Add mid-level SCSI queue depth information to the adapter
            /proc file: /proc/scsi/advansys[0...].

     2.0 (11/14/96):
         1. Change allocation of global structures used for device
            initialization to guarantee they are in DMA-able memory.
            Previously when the driver was loaded as a module these
            structures might not have been in DMA-able memory, causing
            device initialization to fail.

     2.1 (12/30/96):
         1. In advansys_reset(), if the request is a synchronous reset
            request, even if the request serial number has changed, then
            complete the request.
         2. Add Asc Library bug fixes including new microcode.
         3. Clear inquiry buffer before using it.
         4. Correct ifdef typo.

     2.2 (1/15/97):
         1. Add Asc Library bug fixes including new microcode.
         2. Add synchronous data transfer rate information to the
            adapter /proc file: /proc/scsi/advansys[0...].
         3. Change ADVANSYS_DEBUG to be disabled by default. This
            will reduce the size of the driver image, eliminate execution
            overhead, and remove unneeded symbols from the kernel symbol
            space that were previously added by the driver.
         4. Add new compile-time option ADVANSYS_ASSERT for assertion
            code that used to be defined within ADVANSYS_DEBUG. This
            option is enabled by default.

     2.8 (5/26/97):
         1. Change version number to 2.8, skipping 2.3 through 2.7, in
            order to synchronize the Linux driver version numbering with
            other AdvanSys drivers.
         2. Reformat source files without tabs to give everyone everyone
            the same view of the file regardless of the tab setting used.
         3. Add Asc Library bug fixes.

  J. Known Problems or Issues

         1. Remove conditional constants (ASC_QUEUE_FLOW_CONTROL) around
            the queue depth flow control code when mid-level SCSI changes
            are included in Linux.

  K. Credits

     Nathan Hartwell <mage@cdc3.cdc.net> provided the directions and
     basis for the Linux v1.3.X changes which were included in the
     1.2 release.

     Thomas E Zerucha <zerucha@shell.portal.com> pointed out a bug
     in advansys_biosparam() which was fixed in the 1.3 release.

     Erik Ratcliffe <erik@caldera.com> has done a lot of testing of
     the AdvanSys driver in the Caldera releases.

  L. AdvanSys Contact Information
 
     Mail:                   Advanced System Products, Inc.
                             1150 Ringwood Court
                             San Jose, CA 95131
     Operator:               1-408-383-9400
     FAX:                    1-408-383-9612
     Tech Support:           1-800-525-7440/1-408-467-2930
     BBS:                    1-408-383-9540 (14400,N,8,1)
     Interactive FAX:        1-408-383-9753
     Customer Direct Sales:  1-800-883-1099/1-408-383-5777
     Tech Support E-Mail:    support@advansys.com
     FTP Site:               ftp.advansys.com (login: anonymous)
     Web Site:               http://www.advansys.com

*/


/*
 * --- Linux Version
 */

/* Convert Linux Version, Patch-level, Sub-level to LINUX_VERSION_CODE. */
#define ASC_LINUX_VERSION(V, P, S)    (((V) * 65536) + ((P) * 256) + (S))

#ifndef LINUX_VERSION_CODE
#include <linux/version.h>
#endif /* LINUX_VERSION_CODE */


/*
 * --- Linux Include Files 
 */

#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,0)
#ifdef MODULE
#include <linux/module.h>
#endif /* MODULE */
#endif /* version >= v1.3.0 */
#include <linux/string.h>
#include <linux/sched.h>
#include <linux/kernel.h>
#include <linux/head.h>
#include <linux/types.h>
#include <linux/ioport.h>
#include <linux/delay.h>
#include <linux/malloc.h>
#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,0)
#include <linux/proc_fs.h>
#endif /* version >= v1.3.0 */
#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(2,1,23)
#include <linux/init.h>
#endif /* version >= v2.1.23 */
#include <asm/io.h>
#include <asm/system.h>
#include <asm/dma.h>
#if LINUX_VERSION_CODE < ASC_LINUX_VERSION(1,3,0)
#include "../block/blk.h"
#else /* version >= v1.3.0 */
#include <linux/blk.h>
#include <linux/stat.h>
#endif /* version >= v1.3.0 */
#include "scsi.h"
#include "hosts.h"
#include "sd.h"
#include "advansys.h"


/*
 * --- Driver Options
 */

/* Enable driver assertions. */
#define ADVANSYS_ASSERT

/* Enable driver tracing. */
/*#define ADVANSYS_DEBUG*/

/*
 * Because of no /proc to display them, statistics are disabled
 * for version prior to v1.3.0.
 */
#if LINUX_VERSION_CODE < ASC_LINUX_VERSION(1,3,0)
#undef ADVANSYS_STATS /* Disable statistics */
#else /* version >= v1.3.0 */
#define ADVANSYS_STATS /* Enable statistics. */
#endif /* version >= v1.3.0 */


/*
 * --- Debugging Header
 */

#ifdef ADVANSYS_DEBUG
#define STATIC
#else /* ADVANSYS_DEBUG */
#define STATIC static
#endif /* ADVANSYS_DEBUG */


/*
 * --- Asc Library Constants and Macros
 */

#define ASC_LIB_VERSION_MAJOR  1
#define ASC_LIB_VERSION_MINOR  22
#define ASC_LIB_SERIAL_NUMBER  105

typedef unsigned char uchar;

#ifndef NULL
#define NULL     (0)
#endif
#ifndef TRUE
#define TRUE     (1)
#endif
#ifndef FALSE
#define FALSE    (0)
#endif
#define  REG     register
#define rchar    REG __s8
#define rshort   REG __s16
#define rint     REG __s32
#define rlong    REG __s32
#define ruchar   REG __u8
#define rushort  REG __u16
#define ruint    REG __u32
#define rulong   REG __u32
#define NULLPTR  (void *)0
#define FNULLPTR (void *)0UL
#define EOF      (-1)
#define EOS      '\0'
#define ERR      (-1)
#define UB_ERR   (uchar)(0xFF)
#define UW_ERR   (uint)(0xFFFF)
#define UL_ERR   (ulong)(0xFFFFFFFFUL)
#define iseven_word(val)  ((((uint)val) & (uint)0x0001) == 0)
#define isodd_word(val)   ((((uint)val) & (uint)0x0001) != 0)
#define toeven_word(val)  (((uint)val) & (uint)0xFFFE)
#define biton(val, bits)   (((uint)(val >> bits) & (uint)0x0001) != 0)
#define bitoff(val, bits)  (((uint)(val >> bits) & (uint)0x0001) == 0)
#define lbiton(val, bits)  (((ulong)(val >> bits) & (ulong)0x00000001UL) != 0)
#define lbitoff(val, bits) (((ulong)(val >> bits) & (ulong)0x00000001UL) == 0)
#define  absh(val)    ((val) < 0 ? -(val) : (val))
#define  swapbyte(ch)  ((((ch) << 4) | ((ch) >> 4)))
#ifndef GBYTE
#define GBYTE       (0x40000000UL)
#endif
#ifndef MBYTE
#define MBYTE       (0x100000UL)
#endif
#ifndef KBYTE
#define KBYTE       (0x400)
#endif
#define HI_BYTE(x) (*((__u8 *)(&x)+1))
#define LO_BYTE(x) (*((__u8 *)&x))
#define HI_WORD(x) (*((__u16 *)(&x)+1))
#define LO_WORD(x) (*((__u16 *)&x))
#ifndef MAKEWORD
#define MAKEWORD(lo, hi)    ((__u16) (((__u16) lo) | ((__u16) hi << 8)))
#endif
#ifndef MAKELONG
#define MAKELONG(lo, hi)    ((__u32) (((__u32) lo) | ((__u32) hi << 16)))
#endif
#define SwapWords(dWord)        ((__u32) ((dWord >> 16) | (dWord << 16)))
#define SwapBytes(word)         ((__u16) ((word >> 8) | (word << 8)))
#define BigToLittle(dWord) ((__u32) (SwapWords(MAKELONG(SwapBytes(LO_WORD(dWord)), SwapBytes(HI_WORD(dWord))))))
#define LittleToBig(dWord)      BigToLittle(dWord)
#define AscPCIConfigVendorIDRegister      0x0000
#define AscPCIConfigDeviceIDRegister      0x0002
#define AscPCIConfigCommandRegister       0x0004
#define AscPCIConfigStatusRegister        0x0006
#define AscPCIConfigRevisionIDRegister    0x0008
#define AscPCIConfigCacheSize             0x000C
#define AscPCIConfigLatencyTimer          0x000D
#define AscPCIIOBaseRegister              0x0010
#define AscPCICmdRegBits_IOMemBusMaster   0x0007
#define ASC_PCI_ID2BUS(id)    ((id) & 0xFF)
#define ASC_PCI_ID2DEV(id)    (((id) >> 11) & 0x1F)
#define ASC_PCI_ID2FUNC(id)   (((id) >> 8) & 0x7)
#define ASC_PCI_MKID(bus, dev, func) ((((dev) & 0x1F) << 11) | (((func) & 0x7) << 8) | ((bus) & 0xFF))
#define ASC_PCI_VENDORID                  0x10CD
#define ASC_PCI_DEVICEID_1200A            0x1100
#define ASC_PCI_DEVICEID_1200B            0x1200
#define ASC_PCI_DEVICEID_ULTRA            0x1300 
#define ASC_PCI_REVISION_3150             0x02
#define ASC_PCI_REVISION_3050             0x03

#define  ASC_DVCLIB_CALL_DONE     (1)
#define  ASC_DVCLIB_CALL_FAILED   (0)
#define  ASC_DVCLIB_CALL_ERROR    (-1)

#define PortAddr            unsigned short    /* port address size  */
#define Ptr2Func            ulong
#define inp(port)           inb(port)
#define inpw(port)          inw(port)
#define inpl(port)          inl(port)
#define outp(port, byte)    outb((byte), (port))
#define outpw(port, word)   outw((word), (port))
#define outpl(port, long)   outl((long), (port))
#define ASC_MAX_SG_QUEUE    7
#define ASC_MAX_SG_LIST     SG_ALL

#define CC_CLEAR_LRAM_SRB_PTR           FALSE
#define CC_VERIFY_LRAM_COPY             FALSE
#define CC_DEBUG_SG_LIST                FALSE
#define CC_FAST_STRING_IO               FALSE
#define CC_WRITE_IO_COUNT               FALSE
#define CC_CLEAR_DMA_REMAIN             FALSE
#define CC_DISABLE_PCI_PARITY_INT       TRUE
#define CC_LITTLE_ENDIAN_HOST           TRUE
#define CC_STRUCT_ALIGNED               TRUE
#define CC_MEMORY_MAPPED_IO             FALSE
#define CC_INCLUDE_EEP_CONFIG           TRUE
#define CC_PCI_ULTRA                    TRUE
#define CC_ASC_SCSI_Q_USRDEF            FALSE
#define CC_ASC_SCSI_REQ_Q_USRDEF        FALSE
#define CC_ASCISR_CHECK_INT_PENDING     TRUE
#define CC_CHK_FIX_EEP_CONTENT          TRUE
#define CC_INCLUDE_EEP_CONFIG           TRUE
#define CC_PLEXTOR_VL                   FALSE
#define CC_TMP_USE_EEP_SDTR             FALSE
#define CC_CHK_COND_REDO_SDTR           TRUE

#define ASC_CS_TYPE  unsigned short
#ifndef asc_ptr_type
#define asc_ptr_type
#endif

#ifndef ASC_GET_PTR2FUNC
#define ASC_GET_PTR2FUNC(fun)  (Ptr2Func)(fun)
#endif
#define FLIP_BYTE_NIBBLE(x)    (((x<<4)& 0xFF) | (x>>4))
#define ASC_IS_ISA          (0x0001)
#define ASC_IS_ISAPNP       (0x0081)
#define ASC_IS_EISA         (0x0002)
#define ASC_IS_PCI          (0x0004)
#define ASC_IS_PCI_ULTRA    (0x0104)
#define ASC_IS_PCMCIA       (0x0008)
#define ASC_IS_MCA          (0x0020)
#define ASC_IS_VL           (0x0040)
#define ASC_ISA_PNP_PORT_ADDR  (0x279)
#define ASC_ISA_PNP_PORT_WRITE (ASC_ISA_PNP_PORT_ADDR+0x800)
#define ASC_IS_WIDESCSI_16  (0x0100)
#define ASC_IS_WIDESCSI_32  (0x0200)
#define ASC_IS_BIG_ENDIAN   (0x8000)
#define ASC_CHIP_MIN_VER_VL      (0x01)
#define ASC_CHIP_MAX_VER_VL      (0x07)
#define ASC_CHIP_MIN_VER_PCI     (0x09)
#define ASC_CHIP_MAX_VER_PCI     (0x0F)
#define ASC_CHIP_VER_PCI_BIT     (0x08)
#define ASC_CHIP_MIN_VER_ISA     (0x11)
#define ASC_CHIP_MIN_VER_ISA_PNP (0x21)
#define ASC_CHIP_MAX_VER_ISA     (0x27)
#define ASC_CHIP_VER_ISA_BIT     (0x30)
#define ASC_CHIP_VER_ISAPNP_BIT  (0x20)
#define ASC_CHIP_VER_ASYN_BUG    (0x21)
#define ASC_CHIP_VER_PCI             0x08
#define ASC_CHIP_VER_PCI_ULTRA_3150  (ASC_CHIP_VER_PCI | 0x02)
#define ASC_CHIP_VER_PCI_ULTRA_3050  (ASC_CHIP_VER_PCI | 0x03)
#define ASC_CHIP_MIN_VER_EISA (0x41)
#define ASC_CHIP_MAX_VER_EISA (0x47)
#define ASC_CHIP_VER_EISA_BIT (0x40)
#define ASC_CHIP_LATEST_VER_EISA   ((ASC_CHIP_MIN_VER_EISA - 1) + 3)
#define ASC_MAX_LIB_SUPPORTED_ISA_CHIP_VER   0x21
#define ASC_MAX_LIB_SUPPORTED_PCI_CHIP_VER   0x0A
#define ASC_MAX_VL_DMA_ADDR     (0x07FFFFFFL)
#define ASC_MAX_VL_DMA_COUNT    (0x07FFFFFFL)
#define ASC_MAX_PCI_DMA_ADDR    (0xFFFFFFFFL)
#define ASC_MAX_PCI_DMA_COUNT   (0xFFFFFFFFL)
#define ASC_MAX_ISA_DMA_ADDR    (0x00FFFFFFL)
#define ASC_MAX_ISA_DMA_COUNT   (0x00FFFFFFL)
#define ASC_MAX_EISA_DMA_ADDR   (0x07FFFFFFL)
#define ASC_MAX_EISA_DMA_COUNT  (0x07FFFFFFL)
#if !CC_STRUCT_ALIGNED
#define DvcGetQinfo(iop_base, s_addr, outbuf, words)  \
AscMemWordCopyFromLram(iop_base, s_addr, outbuf, words)
#define DvcPutScsiQ(iop_base, s_addr, outbuf, words) \
AscMemWordCopyToLram(iop_base, s_addr, outbuf, words)
#endif
#ifdef ASC_CHIP_VERSION
#endif
#if CC_MEMORY_MAPPED_IO
#define inp(port)            *((uchar *)(port))
#define outp(port, data)     *((uchar *)(port)) = (uchar)(data)
#if CC_LITTLE_ENDIAN_HOST
#define inpw(port)              *((ushort *)(port))
#define outpw(port, data)       *((ushort *)(port)) = (ushort)(data)
#else
#define inpw(port)             EndianSwap16Bit((*((ushort *)(port))))
#define outpw(port, data)      *((ushort *)(port)) = EndianSwap16Bit((ushort)(data))
#define inpw_noswap(port)          *((ushort *)(port))
#define outpw_noswap(port, data)   *((ushort *)(port)) = (ushort)(data)
#endif
#endif
#ifndef inpw_noswap
#define inpw_noswap(port)         inpw(port)
#endif
#ifndef outpw_noswap
#define outpw_noswap(port, data)  outpw(port, data)
#endif
#define ASC_SCSI_ID_BITS  3
#define ASC_SCSI_TIX_TYPE     uchar
#define ASC_ALL_DEVICE_BIT_SET  0xFF
#ifdef ASC_WIDESCSI_16
#undef  ASC_SCSI_ID_BITS
#define ASC_SCSI_ID_BITS  4
#define ASC_ALL_DEVICE_BIT_SET  0xFFFF
#endif
#ifdef ASC_WIDESCSI_32
#undef  ASC_SCSI_ID_BITS
#define ASC_SCSI_ID_BITS  5
#define ASC_ALL_DEVICE_BIT_SET  0xFFFFFFFFL
#endif
#if ASC_SCSI_ID_BITS == 3
#define ASC_SCSI_BIT_ID_TYPE  uchar
#define ASC_MAX_TID       7
#define ASC_MAX_LUN       7
#define ASC_SCSI_WIDTH_BIT_SET  0xFF
#elif ASC_SCSI_ID_BITS == 4
#define ASC_SCSI_BIT_ID_TYPE   ushort
#define ASC_MAX_TID         15
#define ASC_MAX_LUN         7
#define ASC_SCSI_WIDTH_BIT_SET  0xFFFF
#elif ASC_SCSI_ID_BITS == 5
#define ASC_SCSI_BIT_ID_TYPE    ulong
#define ASC_MAX_TID         31
#define ASC_MAX_LUN         7
#define ASC_SCSI_WIDTH_BIT_SET  0xFFFFFFFF
#else
#error  ASC_SCSI_ID_BITS definition is wrong
#endif
#define ASC_MAX_SENSE_LEN   32
#define ASC_MIN_SENSE_LEN   14
#define ASC_MAX_CDB_LEN     12
#define SCSICMD_TestUnitReady     0x00
#define SCSICMD_Rewind            0x01
#define SCSICMD_Rezero            0x01
#define SCSICMD_RequestSense      0x03
#define SCSICMD_Format            0x04
#define SCSICMD_FormatUnit        0x04
#define SCSICMD_Read6             0x08
#define SCSICMD_Write6            0x0A
#define SCSICMD_Seek6             0x0B
#define SCSICMD_Inquiry           0x12
#define SCSICMD_Verify6           0x13
#define SCSICMD_ModeSelect6       0x15
#define SCSICMD_ModeSense6        0x1A
#define SCSICMD_StartStopUnit     0x1B
#define SCSICMD_LoadUnloadTape    0x1B
#define SCSICMD_ReadCapacity      0x25
#define SCSICMD_Read10            0x28
#define SCSICMD_Write10           0x2A
#define SCSICMD_Seek10            0x2B
#define SCSICMD_Erase10           0x2C
#define SCSICMD_WriteAndVerify10  0x2E
#define SCSICMD_Verify10          0x2F
#define SCSICMD_WriteBuffer       0x3B
#define SCSICMD_ReadBuffer        0x3C
#define SCSICMD_ReadLong          0x3E
#define SCSICMD_WriteLong         0x3F
#define SCSICMD_ReadTOC           0x43
#define SCSICMD_ReadHeader        0x44
#define SCSICMD_ModeSelect10      0x55
#define SCSICMD_ModeSense10       0x5A
#define SCSI_TYPE_DASD     0x00
#define SCSI_TYPE_SASD     0x01
#define SCSI_TYPE_PRN      0x02
#define SCSI_TYPE_PROC     0x03
#define SCSI_TYPE_WORM     0x04
#define SCSI_TYPE_CDROM    0x05
#define SCSI_TYPE_SCANNER  0x06
#define SCSI_TYPE_OPTMEM   0x07
#define SCSI_TYPE_MED_CHG  0x08
#define SCSI_TYPE_COMM     0x09
#define SCSI_TYPE_UNKNOWN  0x1F
#define SCSI_TYPE_NO_DVC   0xFF
#define ASC_SCSIDIR_NOCHK    0x00
#define ASC_SCSIDIR_T2H      0x08
#define ASC_SCSIDIR_H2T      0x10
#define ASC_SCSIDIR_NODATA   0x18
#define SCSI_SENKEY_NO_SENSE      0x00
#define SCSI_SENKEY_UNDEFINED     0x01
#define SCSI_SENKEY_NOT_READY     0x02
#define SCSI_SENKEY_MEDIUM_ERR    0x03
#define SCSI_SENKEY_HW_ERR        0x04
#define SCSI_SENKEY_ILLEGAL       0x05
#define SCSI_SENKEY_ATTENTION     0x06
#define SCSI_SENKEY_PROTECTED     0x07
#define SCSI_SENKEY_BLANK         0x08
#define SCSI_SENKEY_V_UNIQUE      0x09
#define SCSI_SENKEY_CPY_ABORT     0x0A
#define SCSI_SENKEY_ABORT         0x0B
#define SCSI_SENKEY_EQUAL         0x0C
#define SCSI_SENKEY_VOL_OVERFLOW  0x0D
#define SCSI_SENKEY_MISCOMP       0x0E
#define SCSI_SENKEY_RESERVED      0x0F
#define ASC_SRB_HOST(x)  ((uchar)((uchar)(x) >> 4))
#define ASC_SRB_TID(x)   ((uchar)((uchar)(x) & (uchar)0x0F))
#define ASC_SRB_LUN(x)   ((uchar)((uint)(x) >> 13))
#define PUT_CDB1(x)   ((uchar)((uint)(x) >> 8))
#define SS_GOOD              0x00
#define SS_CHK_CONDITION     0x02
#define SS_CONDITION_MET     0x04
#define SS_TARGET_BUSY       0x08
#define SS_INTERMID          0x10
#define SS_INTERMID_COND_MET 0x14
#define SS_RSERV_CONFLICT    0x18
#define SS_CMD_TERMINATED    0x22
#define SS_QUEUE_FULL        0x28
#define MS_CMD_DONE    0x00
#define MS_EXTEND      0x01
#define MS_SDTR_LEN    0x03
#define MS_SDTR_CODE   0x01
#define MS_WDTR_LEN    0x02
#define MS_WDTR_CODE   0x03
#define MS_MDP_LEN    0x05
#define MS_MDP_CODE   0x00
#define M1_SAVE_DATA_PTR        0x02
#define M1_RESTORE_PTRS         0x03
#define M1_DISCONNECT           0x04
#define M1_INIT_DETECTED_ERR    0x05
#define M1_ABORT                0x06
#define M1_MSG_REJECT           0x07
#define M1_NO_OP                0x08
#define M1_MSG_PARITY_ERR       0x09
#define M1_LINK_CMD_DONE        0x0A
#define M1_LINK_CMD_DONE_WFLAG  0x0B
#define M1_BUS_DVC_RESET        0x0C
#define M1_ABORT_TAG            0x0D
#define M1_CLR_QUEUE            0x0E
#define M1_INIT_RECOVERY        0x0F
#define M1_RELEASE_RECOVERY     0x10
#define M1_KILL_IO_PROC         0x11
#define M2_QTAG_MSG_SIMPLE      0x20
#define M2_QTAG_MSG_HEAD        0x21
#define M2_QTAG_MSG_ORDERED     0x22
#define M2_IGNORE_WIDE_RESIDUE  0x23

#if CC_LITTLE_ENDIAN_HOST
typedef struct {
    uchar               peri_dvc_type:5;
    uchar               peri_qualifier:3;
} ASC_SCSI_INQ0;

#else
typedef struct {
    uchar               peri_qualifier:3;
    uchar               peri_dvc_type:5;
} ASC_SCSI_INQ0;

#endif
#if CC_LITTLE_ENDIAN_HOST
typedef struct {
    uchar               dvc_type_modifier:7;
    uchar               rmb:1;
} ASC_SCSI_INQ1;

#else
typedef struct {
    uchar               rmb:1;
    uchar               dvc_type_modifier:7;
} ASC_SCSI_INQ1;

#endif
#if CC_LITTLE_ENDIAN_HOST
typedef struct {
    uchar               ansi_apr_ver:3;
    uchar               ecma_ver:3;
    uchar               iso_ver:2;
} ASC_SCSI_INQ2;

#else
typedef struct {
    uchar               iso_ver:2;
    uchar               ecma_ver:3;
    uchar               ansi_apr_ver:3;
} ASC_SCSI_INQ2;

#endif
#if CC_LITTLE_ENDIAN_HOST
typedef struct {
    uchar               rsp_data_fmt:4;
    uchar               res:2;
    uchar               TemIOP:1;
    uchar               aenc:1;
} ASC_SCSI_INQ3;

#else
typedef struct {
    uchar               aenc:1;
    uchar               TemIOP:1;
    uchar               res:2;
    uchar               rsp_data_fmt:4;
} ASC_SCSI_INQ3;

#endif
#if CC_LITTLE_ENDIAN_HOST
typedef struct {
    uchar               StfRe:1;
    uchar               CmdQue:1;
    uchar               Reserved:1;
    uchar               Linked:1;
    uchar               Sync:1;
    uchar               WBus16:1;
    uchar               WBus32:1;
    uchar               RelAdr:1;
} ASC_SCSI_INQ7;

#else
typedef struct {
    uchar               RelAdr:1;
    uchar               WBus32:1;
    uchar               WBus16:1;
    uchar               Sync:1;
    uchar               Linked:1;
    uchar               Reserved:1;
    uchar               CmdQue:1;
    uchar               StfRe:1;
} ASC_SCSI_INQ7;

#endif
typedef struct {
    ASC_SCSI_INQ0       byte0;
    ASC_SCSI_INQ1       byte1;
    ASC_SCSI_INQ2       byte2;
    ASC_SCSI_INQ3       byte3;
    uchar               add_len;
    uchar               res1;
    uchar               res2;
    ASC_SCSI_INQ7       byte7;
    uchar               vendor_id[8];
    uchar               product_id[16];
    uchar               product_rev_level[4];
} ASC_SCSI_INQUIRY;

#if CC_LITTLE_ENDIAN_HOST
typedef struct asc_req_sense {
    uchar               err_code:7;
    uchar               info_valid:1;
    uchar               segment_no;
    uchar               sense_key:4;
    uchar               reserved_bit:1;
    uchar               sense_ILI:1;
    uchar               sense_EOM:1;
    uchar               file_mark:1;
    uchar               info1[4];
    uchar               add_sense_len;
    uchar               cmd_sp_info[4];
    uchar               asc;
    uchar               ascq;
    uchar               fruc;
    uchar               sks_byte0:7;
    uchar               sks_valid:1;
    uchar               sks_bytes[2];
    uchar               notused[2];
    uchar               ex_sense_code;
    uchar               info2[4];
} ASC_REQ_SENSE;

#else
typedef struct asc_req_sense {
    uchar               info_valid:1;
    uchar               err_code:7;
    uchar               segment_no;
    uchar               file_mark:1;
    uchar               sense_EOM:1;
    uchar               sense_ILI:1;
    uchar               reserved_bit:1;
    uchar               sense_key:4;
    uchar               info1[4];
    uchar               add_sense_len;
    uchar               cmd_sp_info[4];
    uchar               asc;
    uchar               ascq;
    uchar               fruc;
    uchar               sks_valid:1;
    uchar               sks_byte0:7;
    uchar               sks_bytes[2];
    uchar               notused[2];
    uchar               ex_sense_code;
    uchar               info2[4];
} ASC_REQ_SENSE;

#endif
#define ASC_SG_LIST_PER_Q   7
#define QS_FREE        0x00
#define QS_READY       0x01
#define QS_DISC1       0x02
#define QS_DISC2       0x04
#define QS_BUSY        0x08
#define QS_ABORTED     0x40
#define QS_DONE        0x80
#define QC_NO_CALLBACK   0x01
#define QC_SG_SWAP_QUEUE 0x02
#define QC_SG_HEAD       0x04
#define QC_DATA_IN       0x08
#define QC_DATA_OUT      0x10
#define QC_URGENT        0x20
#define QC_MSG_OUT       0x40
#define QC_REQ_SENSE     0x80
#define QCSG_SG_XFER_LIST  0x02
#define QCSG_SG_XFER_MORE  0x04
#define QCSG_SG_XFER_END   0x08
#define QD_IN_PROGRESS       0x00
#define QD_NO_ERROR          0x01
#define QD_ABORTED_BY_HOST   0x02
#define QD_WITH_ERROR        0x04
#define QD_INVALID_REQUEST   0x80
#define QD_INVALID_HOST_NUM  0x81
#define QD_INVALID_DEVICE    0x82
#define QD_ERR_INTERNAL      0xFF
#define QHSTA_NO_ERROR               0x00
#define QHSTA_M_SEL_TIMEOUT          0x11
#define QHSTA_M_DATA_OVER_RUN        0x12
#define QHSTA_M_DATA_UNDER_RUN       0x12
#define QHSTA_M_UNEXPECTED_BUS_FREE  0x13
#define QHSTA_M_BAD_BUS_PHASE_SEQ    0x14
#define QHSTA_D_QDONE_SG_LIST_CORRUPTED 0x21
#define QHSTA_D_ASC_DVC_ERROR_CODE_SET  0x22
#define QHSTA_D_HOST_ABORT_FAILED       0x23
#define QHSTA_D_EXE_SCSI_Q_FAILED       0x24
#define QHSTA_D_EXE_SCSI_Q_BUSY_TIMEOUT 0x25
#define QHSTA_D_ASPI_NO_BUF_POOL        0x26
#define QHSTA_M_WTM_TIMEOUT         0x41
#define QHSTA_M_BAD_CMPL_STATUS_IN  0x42
#define QHSTA_M_NO_AUTO_REQ_SENSE   0x43
#define QHSTA_M_AUTO_REQ_SENSE_FAIL 0x44
#define QHSTA_M_TARGET_STATUS_BUSY  0x45
#define QHSTA_M_BAD_TAG_CODE        0x46
#define QHSTA_M_BAD_QUEUE_FULL_OR_BUSY  0x47
#define QHSTA_M_HUNG_REQ_SCSI_BUS_RESET 0x48
#define QHSTA_D_LRAM_CMP_ERROR        0x81
#define QHSTA_M_MICRO_CODE_ERROR_HALT 0xA1
#define ASC_FLAG_SCSIQ_REQ        0x01
#define ASC_FLAG_BIOS_SCSIQ_REQ   0x02
#define ASC_FLAG_BIOS_ASYNC_IO    0x04
#define ASC_FLAG_SRB_LINEAR_ADDR  0x08
#define ASC_FLAG_WIN16            0x10
#define ASC_FLAG_WIN32            0x20
#define ASC_FLAG_ISA_OVER_16MB    0x40
#define ASC_FLAG_DOS_VM_CALLBACK  0x80
#define ASC_TAG_FLAG_EXTRA_BYTES               0x10
#define ASC_TAG_FLAG_DISABLE_DISCONNECT        0x04
#define ASC_TAG_FLAG_DISABLE_ASYN_USE_SYN_FIX  0x08
#define ASC_TAG_FLAG_DISABLE_CHK_COND_INT_HOST 0x40
#define ASC_SCSIQ_CPY_BEG              4
#define ASC_SCSIQ_SGHD_CPY_BEG         2
#define ASC_SCSIQ_B_FWD                0
#define ASC_SCSIQ_B_BWD                1
#define ASC_SCSIQ_B_STATUS             2
#define ASC_SCSIQ_B_QNO                3
#define ASC_SCSIQ_B_CNTL               4
#define ASC_SCSIQ_B_SG_QUEUE_CNT       5
#define ASC_SCSIQ_D_DATA_ADDR          8
#define ASC_SCSIQ_D_DATA_CNT          12
#define ASC_SCSIQ_B_SENSE_LEN         20
#define ASC_SCSIQ_DONE_INFO_BEG       22
#define ASC_SCSIQ_D_SRBPTR            22
#define ASC_SCSIQ_B_TARGET_IX         26
#define ASC_SCSIQ_B_CDB_LEN           28
#define ASC_SCSIQ_B_TAG_CODE          29
#define ASC_SCSIQ_W_VM_ID             30
#define ASC_SCSIQ_DONE_STATUS         32
#define ASC_SCSIQ_HOST_STATUS         33
#define ASC_SCSIQ_SCSI_STATUS         34
#define ASC_SCSIQ_CDB_BEG             36
#define ASC_SCSIQ_DW_REMAIN_XFER_ADDR 56
#define ASC_SCSIQ_DW_REMAIN_XFER_CNT  60
#define ASC_SCSIQ_B_SG_WK_QP          49
#define ASC_SCSIQ_B_SG_WK_IX          50
#define ASC_SCSIQ_W_REQ_COUNT         52
#define ASC_SCSIQ_B_LIST_CNT          6
#define ASC_SCSIQ_B_CUR_LIST_CNT      7
#define ASC_SGQ_B_SG_CNTL             4
#define ASC_SGQ_B_SG_HEAD_QP          5
#define ASC_SGQ_B_SG_LIST_CNT         6
#define ASC_SGQ_B_SG_CUR_LIST_CNT     7
#define ASC_SGQ_LIST_BEG              8
#define ASC_DEF_SCSI1_QNG    4
#define ASC_MAX_SCSI1_QNG    4
#define ASC_DEF_SCSI2_QNG    16
#define ASC_MAX_SCSI2_QNG    32
#define ASC_TAG_CODE_MASK    0x23
#define ASC_STOP_REQ_RISC_STOP      0x01
#define ASC_STOP_ACK_RISC_STOP      0x03
#define ASC_STOP_CLEAN_UP_BUSY_Q    0x10
#define ASC_STOP_CLEAN_UP_DISC_Q    0x20
#define ASC_STOP_HOST_REQ_RISC_HALT 0x40
#define ASC_TIDLUN_TO_IX(tid, lun)  (ASC_SCSI_TIX_TYPE)((tid) + ((lun)<<ASC_SCSI_ID_BITS))
#define ASC_TID_TO_TARGET_ID(tid)   (ASC_SCSI_BIT_ID_TYPE)(0x01 << (tid))
#define ASC_TIX_TO_TARGET_ID(tix)   (0x01 << ((tix) & ASC_MAX_TID))
#define ASC_TIX_TO_TID(tix)         ((tix) & ASC_MAX_TID)
#define ASC_TID_TO_TIX(tid)         ((tid) & ASC_MAX_TID)
#define ASC_TIX_TO_LUN(tix)         (((tix) >> ASC_SCSI_ID_BITS) & ASC_MAX_LUN)
#define ASC_QNO_TO_QADDR(q_no)      ((ASC_QADR_BEG)+((int)(q_no) << 6))

typedef struct asc_scisq_1 {
    uchar               status;
    uchar               q_no;
    uchar               cntl;
    uchar               sg_queue_cnt;
    uchar               target_id;
    uchar               target_lun;
    ulong               data_addr;
    ulong               data_cnt;
    ulong               sense_addr;
    uchar               sense_len;
    uchar               extra_bytes;
} ASC_SCSIQ_1;

typedef struct asc_scisq_2 {
    ulong               srb_ptr;
    uchar               target_ix;
    uchar               flag;
    uchar               cdb_len;
    uchar               tag_code;
    ushort              vm_id;
} ASC_SCSIQ_2;

typedef struct asc_scsiq_3 {
    uchar               done_stat;
    uchar               host_stat;
    uchar               scsi_stat;
    uchar               scsi_msg;
} ASC_SCSIQ_3;

typedef struct asc_scsiq_4 {
    uchar               cdb[ASC_MAX_CDB_LEN];
    uchar               y_first_sg_list_qp;
    uchar               y_working_sg_qp;
    uchar               y_working_sg_ix;
    uchar               y_res;
    ushort              x_req_count;
    ushort              x_reconnect_rtn;
    ulong               x_saved_data_addr;
    ulong               x_saved_data_cnt;
} ASC_SCSIQ_4;

typedef struct asc_q_done_info {
    ASC_SCSIQ_2         d2;
    ASC_SCSIQ_3         d3;
    uchar               q_status;
    uchar               q_no;
    uchar               cntl;
    uchar               sense_len;
    uchar               extra_bytes;
    uchar               res;
    ulong               remain_bytes;
} ASC_QDONE_INFO;

typedef struct asc_sg_list {
    ulong               addr;
    ulong               bytes;
} ASC_SG_LIST;

typedef struct asc_sg_head {
    ushort              entry_cnt;
    ushort              queue_cnt;
    ushort              entry_to_copy;
    ushort              res;
    ASC_SG_LIST         sg_list[ASC_MAX_SG_LIST];
} ASC_SG_HEAD;

#define ASC_MIN_SG_LIST   2

typedef struct asc_min_sg_head {
    ushort              entry_cnt;
    ushort              queue_cnt;
    ushort              entry_to_copy;
    ushort              res;
    ASC_SG_LIST         sg_list[ASC_MIN_SG_LIST];
} ASC_MIN_SG_HEAD;

#define QCX_SORT        (0x0001)
#define QCX_COALEASE    (0x0002)

typedef struct asc_scsi_q {
    ASC_SCSIQ_1         q1;
    ASC_SCSIQ_2         q2;
    uchar               *cdbptr;
    ASC_SG_HEAD         *sg_head;
#if CC_ASC_SCSI_Q_USRDEF
    ASC_SCSI_Q_USR      usr;
#endif
} ASC_SCSI_Q;

typedef struct asc_scsi_req_q {
    ASC_SCSIQ_1         r1;
    ASC_SCSIQ_2         r2;
    uchar       *cdbptr;
    ASC_SG_HEAD *sg_head;
    uchar               *sense_ptr;
    ASC_SCSIQ_3         r3;
    uchar               cdb[ASC_MAX_CDB_LEN];
    uchar               sense[ASC_MIN_SENSE_LEN];
#if CC_ASC_SCSI_REQ_Q_USRDEF
    ASC_SCSI_REQ_Q_USR  usr;
#endif
} ASC_SCSI_REQ_Q;

typedef struct asc_scsi_bios_req_q {
    ASC_SCSIQ_1         r1;
    ASC_SCSIQ_2         r2;
    uchar               *cdbptr;
    ASC_SG_HEAD         *sg_head;
    uchar               *sense_ptr;
    ASC_SCSIQ_3         r3;
    uchar               cdb[ASC_MAX_CDB_LEN];
    uchar               sense[ASC_MIN_SENSE_LEN];
} ASC_SCSI_BIOS_REQ_Q;

typedef struct asc_risc_q {
    uchar               fwd;
    uchar               bwd;
    ASC_SCSIQ_1         i1;
    ASC_SCSIQ_2         i2;
    ASC_SCSIQ_3         i3;
    ASC_SCSIQ_4         i4;
} ASC_RISC_Q;

typedef struct asc_sg_list_q {
    uchar               seq_no;
    uchar               q_no;
    uchar               cntl;
    uchar               sg_head_qp;
    uchar               sg_list_cnt;
    uchar               sg_cur_list_cnt;
} ASC_SG_LIST_Q;

typedef struct asc_risc_sg_list_q {
    uchar               fwd;
    uchar               bwd;
    ASC_SG_LIST_Q       sg;
    ASC_SG_LIST         sg_list[7];
} ASC_RISC_SG_LIST_Q;

#define ASC_EXE_SCSI_IO_MAX_IDLE_LOOP  0x1000000UL
#define ASC_EXE_SCSI_IO_MAX_WAIT_LOOP  1024
#define ASCQ_ERR_NO_ERROR             0
#define ASCQ_ERR_IO_NOT_FOUND         1
#define ASCQ_ERR_LOCAL_MEM            2
#define ASCQ_ERR_CHKSUM               3
#define ASCQ_ERR_START_CHIP           4
#define ASCQ_ERR_INT_TARGET_ID        5
#define ASCQ_ERR_INT_LOCAL_MEM        6
#define ASCQ_ERR_HALT_RISC            7
#define ASCQ_ERR_GET_ASPI_ENTRY       8
#define ASCQ_ERR_CLOSE_ASPI           9
#define ASCQ_ERR_HOST_INQUIRY         0x0A
#define ASCQ_ERR_SAVED_SRB_BAD        0x0B
#define ASCQ_ERR_QCNTL_SG_LIST        0x0C
#define ASCQ_ERR_Q_STATUS             0x0D
#define ASCQ_ERR_WR_SCSIQ             0x0E
#define ASCQ_ERR_PC_ADDR              0x0F
#define ASCQ_ERR_SYN_OFFSET           0x10
#define ASCQ_ERR_SYN_XFER_TIME        0x11
#define ASCQ_ERR_LOCK_DMA             0x12
#define ASCQ_ERR_UNLOCK_DMA           0x13
#define ASCQ_ERR_VDS_CHK_INSTALL      0x14
#define ASCQ_ERR_MICRO_CODE_HALT      0x15
#define ASCQ_ERR_SET_LRAM_ADDR        0x16
#define ASCQ_ERR_CUR_QNG              0x17
#define ASCQ_ERR_SG_Q_LINKS           0x18
#define ASCQ_ERR_SCSIQ_PTR            0x19
#define ASCQ_ERR_ISR_RE_ENTRY         0x1A
#define ASCQ_ERR_CRITICAL_RE_ENTRY    0x1B
#define ASCQ_ERR_ISR_ON_CRITICAL      0x1C
#define ASCQ_ERR_SG_LIST_ODD_ADDRESS  0x1D
#define ASCQ_ERR_XFER_ADDRESS_TOO_BIG 0x1E
#define ASCQ_ERR_SCSIQ_NULL_PTR       0x1F
#define ASCQ_ERR_SCSIQ_BAD_NEXT_PTR   0x20
#define ASCQ_ERR_GET_NUM_OF_FREE_Q    0x21
#define ASCQ_ERR_SEND_SCSI_Q          0x22
#define ASCQ_ERR_HOST_REQ_RISC_HALT   0x23
#define ASCQ_ERR_RESET_SDTR           0x24
#define ASC_WARN_NO_ERROR             0x0000
#define ASC_WARN_IO_PORT_ROTATE       0x0001
#define ASC_WARN_EEPROM_CHKSUM        0x0002
#define ASC_WARN_IRQ_MODIFIED         0x0004
#define ASC_WARN_AUTO_CONFIG          0x0008
#define ASC_WARN_CMD_QNG_CONFLICT     0x0010
#define ASC_WARN_EEPROM_RECOVER       0x0020
#define ASC_WARN_CFG_MSW_RECOVER      0x0040
#define ASC_WARN_SET_PCI_CONFIG_SPACE 0x0080
#define ASC_IERR_WRITE_EEPROM         0x0001
#define ASC_IERR_MCODE_CHKSUM         0x0002
#define ASC_IERR_SET_PC_ADDR          0x0004
#define ASC_IERR_START_STOP_CHIP      0x0008
#define ASC_IERR_IRQ_NO               0x0010
#define ASC_IERR_SET_IRQ_NO           0x0020
#define ASC_IERR_CHIP_VERSION         0x0040
#define ASC_IERR_SET_SCSI_ID          0x0080
#define ASC_IERR_GET_PHY_ADDR         0x0100
#define ASC_IERR_BAD_SIGNATURE        0x0200
#define ASC_IERR_NO_BUS_TYPE          0x0400
#define ASC_IERR_SCAM                 0x0800
#define ASC_IERR_SET_SDTR             0x1000
#define ASC_IERR_RW_LRAM              0x8000
#define ASC_DEF_IRQ_NO  10
#define ASC_MAX_IRQ_NO  15
#define ASC_MIN_IRQ_NO  10
#define ASC_MIN_REMAIN_Q        (0x02)
#define ASC_DEF_MAX_TOTAL_QNG   (0xF0)
#define ASC_MIN_TAG_Q_PER_DVC   (0x04)
#define ASC_DEF_TAG_Q_PER_DVC   (0x04)
#define ASC_MIN_FREE_Q        ASC_MIN_REMAIN_Q
#define ASC_MIN_TOTAL_QNG     ((ASC_MAX_SG_QUEUE)+(ASC_MIN_FREE_Q))
#define ASC_MAX_TOTAL_QNG 240
#define ASC_MAX_PCI_ULTRA_INRAM_TOTAL_QNG 16
#define ASC_MAX_PCI_ULTRA_INRAM_TAG_QNG   8
#define ASC_MAX_PCI_INRAM_TOTAL_QNG  20
#define ASC_MAX_INRAM_TAG_QNG   16
#define ASC_IOADR_TABLE_MAX_IX  11
#define ASC_IOADR_GAP   0x10
#define ASC_SEARCH_IOP_GAP 0x10
#define ASC_MIN_IOP_ADDR   (PortAddr)0x0100
#define ASC_MAX_IOP_ADDR   (PortAddr)0x3F0
#define ASC_IOADR_1     (PortAddr)0x0110
#define ASC_IOADR_2     (PortAddr)0x0130
#define ASC_IOADR_3     (PortAddr)0x0150
#define ASC_IOADR_4     (PortAddr)0x0190
#define ASC_IOADR_5     (PortAddr)0x0210
#define ASC_IOADR_6     (PortAddr)0x0230
#define ASC_IOADR_7     (PortAddr)0x0250
#define ASC_IOADR_8     (PortAddr)0x0330
#define ASC_IOADR_DEF   ASC_IOADR_8
#define ASC_LIB_SCSIQ_WK_SP        256
#define ASC_MAX_SYN_XFER_NO        16
#define ASC_SYN_MAX_OFFSET         0x0F
#define ASC_DEF_SDTR_OFFSET        0x0F
#define ASC_DEF_SDTR_INDEX         0x00
#define ASC_SDTR_ULTRA_PCI_10MB_INDEX  0x02
#define SYN_XFER_NS_0  25
#define SYN_XFER_NS_1  30
#define SYN_XFER_NS_2  35
#define SYN_XFER_NS_3  40
#define SYN_XFER_NS_4  50
#define SYN_XFER_NS_5  60
#define SYN_XFER_NS_6  70
#define SYN_XFER_NS_7  85
#define SYN_ULTRA_XFER_NS_0    12
#define SYN_ULTRA_XFER_NS_1    19
#define SYN_ULTRA_XFER_NS_2    25
#define SYN_ULTRA_XFER_NS_3    32
#define SYN_ULTRA_XFER_NS_4    38
#define SYN_ULTRA_XFER_NS_5    44
#define SYN_ULTRA_XFER_NS_6    50
#define SYN_ULTRA_XFER_NS_7    57
#define SYN_ULTRA_XFER_NS_8    63
#define SYN_ULTRA_XFER_NS_9    69
#define SYN_ULTRA_XFER_NS_10   75
#define SYN_ULTRA_XFER_NS_11   82
#define SYN_ULTRA_XFER_NS_12   88
#define SYN_ULTRA_XFER_NS_13   94
#define SYN_ULTRA_XFER_NS_14  100
#define SYN_ULTRA_XFER_NS_15  107

typedef struct ext_msg {
    uchar               msg_type;
    uchar               msg_len;
    uchar               msg_req;
    union {
        struct {
            uchar               sdtr_xfer_period;
            uchar               sdtr_req_ack_offset;
        } sdtr;
        struct {
            uchar               wdtr_width;
        } wdtr;
        struct {
            uchar               mdp_b3;
            uchar               mdp_b2;
            uchar               mdp_b1;
            uchar               mdp_b0;
        } mdp;
    } u_ext_msg;
    uchar               res;
} EXT_MSG;

#define xfer_period     u_ext_msg.sdtr.sdtr_xfer_period
#define req_ack_offset  u_ext_msg.sdtr.sdtr_req_ack_offset
#define wdtr_width      u_ext_msg.wdtr.wdtr_width
#define mdp_b3          u_ext_msg.mdp_b3
#define mdp_b2          u_ext_msg.mdp_b2
#define mdp_b1          u_ext_msg.mdp_b1
#define mdp_b0          u_ext_msg.mdp_b0

typedef struct asc_dvc_cfg {
    ASC_SCSI_BIT_ID_TYPE can_tagged_qng;
    ASC_SCSI_BIT_ID_TYPE cmd_qng_enabled;
    ASC_SCSI_BIT_ID_TYPE disc_enable;
    uchar               res;
    uchar               chip_scsi_id:4;
    uchar               isa_dma_speed:4;
    uchar               isa_dma_channel;
    uchar               chip_version;
    ushort              pci_device_id;
    ushort              lib_serial_no;
    ushort              lib_version;
    ushort              mcode_date;
    ushort              mcode_version;
    uchar               max_tag_qng[ASC_MAX_TID + 1];
    uchar       *overrun_buf;
    uchar               sdtr_period_offset[ASC_MAX_TID + 1];
    ushort              pci_slot_info;
} ASC_DVC_CFG;

#define ASC_DEF_DVC_CNTL       0xFFFF
#define ASC_DEF_CHIP_SCSI_ID   7
#define ASC_DEF_ISA_DMA_SPEED  4
#define ASC_INIT_STATE_NULL          0x0000
#define ASC_INIT_STATE_BEG_GET_CFG   0x0001
#define ASC_INIT_STATE_END_GET_CFG   0x0002
#define ASC_INIT_STATE_BEG_SET_CFG   0x0004
#define ASC_INIT_STATE_END_SET_CFG   0x0008
#define ASC_INIT_STATE_BEG_LOAD_MC   0x0010
#define ASC_INIT_STATE_END_LOAD_MC   0x0020
#define ASC_INIT_STATE_BEG_INQUIRY   0x0040
#define ASC_INIT_STATE_END_INQUIRY   0x0080
#define ASC_INIT_RESET_SCSI_DONE     0x0100
#define ASC_INIT_STATE_WITHOUT_EEP   0x8000
#define ASC_PCI_DEVICE_ID_REV_A      0x1100
#define ASC_PCI_DEVICE_ID_REV_B      0x1200
#define ASC_BUG_FIX_IF_NOT_DWB       0x0001
#define ASC_BUG_FIX_ASYN_USE_SYN     0x0002
#define ASYN_SDTR_DATA_FIX_PCI_REV_AB 0x41
#define ASC_MIN_TAGGED_CMD  7
#define ASC_MAX_SCSI_RESET_WAIT      30

typedef struct asc_dvc_var {
    PortAddr            iop_base;
    ushort              err_code;
    ushort              dvc_cntl;
    ushort              bug_fix_cntl;
    ushort              bus_type;
    Ptr2Func            isr_callback;
    Ptr2Func            exe_callback;
    ASC_SCSI_BIT_ID_TYPE init_sdtr;
    ASC_SCSI_BIT_ID_TYPE sdtr_done;
    ASC_SCSI_BIT_ID_TYPE use_tagged_qng;
    ASC_SCSI_BIT_ID_TYPE unit_not_ready;
    ASC_SCSI_BIT_ID_TYPE queue_full_or_busy;
    ASC_SCSI_BIT_ID_TYPE start_motor;
    uchar               scsi_reset_wait;
    uchar               chip_no;
    char                is_in_int;
    uchar               max_total_qng;
    uchar               cur_total_qng;
    uchar               in_critical_cnt;
    uchar               irq_no;
    uchar               last_q_shortage;
    ushort              init_state;
    uchar               cur_dvc_qng[ASC_MAX_TID + 1];
    uchar               max_dvc_qng[ASC_MAX_TID + 1];
    ASC_SCSI_Q  *scsiq_busy_head[ASC_MAX_TID + 1];
    ASC_SCSI_Q  *scsiq_busy_tail[ASC_MAX_TID + 1];
    uchar               sdtr_period_tbl[ASC_MAX_SYN_XFER_NO];
    ASC_DVC_CFG *cfg;
    Ptr2Func            saved_ptr2func;
    ASC_SCSI_BIT_ID_TYPE pci_fix_asyn_xfer_always;
    char                redo_scam;
    ushort              res2;
    uchar               dos_int13_table[ASC_MAX_TID + 1];
    ulong               max_dma_count;
    ASC_SCSI_BIT_ID_TYPE no_scam;
    ASC_SCSI_BIT_ID_TYPE pci_fix_asyn_xfer;
    uchar               max_sdtr_index;
    uchar               host_init_sdtr_index;
    ulong               drv_ptr;
    ulong               uc_break;
    ulong               res7;
    ulong               res8;
} ASC_DVC_VAR;

typedef int (* ASC_ISR_CALLBACK) (ASC_DVC_VAR asc_ptr_type *, ASC_QDONE_INFO *);
typedef int (* ASC_EXE_CALLBACK) (ASC_DVC_VAR asc_ptr_type *, ASC_SCSI_Q *);

typedef struct asc_dvc_inq_info {
    uchar               type[ASC_MAX_TID + 1][ASC_MAX_LUN + 1];
} ASC_DVC_INQ_INFO;

typedef struct asc_cap_info {
    ulong               lba;
    ulong               blk_size;
} ASC_CAP_INFO;

typedef struct asc_cap_info_array {
    ASC_CAP_INFO        cap_info[ASC_MAX_TID + 1][ASC_MAX_LUN + 1];
} ASC_CAP_INFO_ARRAY;

#define ASC_MCNTL_NO_SEL_TIMEOUT  (ushort)0x0001
#define ASC_MCNTL_NULL_TARGET     (ushort)0x0002
#define ASC_CNTL_INITIATOR         (ushort)0x0001
#define ASC_CNTL_BIOS_GT_1GB       (ushort)0x0002
#define ASC_CNTL_BIOS_GT_2_DISK    (ushort)0x0004
#define ASC_CNTL_BIOS_REMOVABLE    (ushort)0x0008
#define ASC_CNTL_NO_SCAM           (ushort)0x0010
#define ASC_CNTL_INT_MULTI_Q       (ushort)0x0080
#define ASC_CNTL_NO_LUN_SUPPORT    (ushort)0x0040
#define ASC_CNTL_NO_VERIFY_COPY    (ushort)0x0100
#define ASC_CNTL_RESET_SCSI        (ushort)0x0200
#define ASC_CNTL_INIT_INQUIRY      (ushort)0x0400
#define ASC_CNTL_INIT_VERBOSE      (ushort)0x0800
#define ASC_CNTL_SCSI_PARITY       (ushort)0x1000
#define ASC_CNTL_BURST_MODE        (ushort)0x2000
#define ASC_CNTL_SDTR_ENABLE_ULTRA (ushort)0x4000
#define ASC_EEP_DVC_CFG_BEG_VL    2
#define ASC_EEP_MAX_DVC_ADDR_VL   15
#define ASC_EEP_DVC_CFG_BEG      32
#define ASC_EEP_MAX_DVC_ADDR     45
#define ASC_EEP_DEFINED_WORDS    10
#define ASC_EEP_MAX_ADDR         63
#define ASC_EEP_RES_WORDS         0
#define ASC_EEP_MAX_RETRY        20
#define ASC_MAX_INIT_BUSY_RETRY   8
#define ASC_EEP_ISA_PNP_WSIZE    16

typedef struct asceep_config {
    ushort              cfg_lsw;
    ushort              cfg_msw;
    uchar               init_sdtr;
    uchar               disc_enable;
    uchar               use_cmd_qng;
    uchar               start_motor;
    uchar               max_total_qng;
    uchar               max_tag_qng;
    uchar               bios_scan;
    uchar               power_up_wait;
    uchar               no_scam;
    uchar               chip_scsi_id:4;
    uchar               isa_dma_speed:4;
    uchar               dos_int13_table[ASC_MAX_TID + 1];
    uchar               adapter_info[6];
    ushort              cntl;
    ushort              chksum;
} ASCEEP_CONFIG;

#define ASC_PCI_CFG_LSW_SCSI_PARITY  0x0800
#define ASC_PCI_CFG_LSW_BURST_MODE   0x0080
#define ASC_PCI_CFG_LSW_INTR_ABLE    0x0020

#define ASC_EEP_CMD_READ          0x80
#define ASC_EEP_CMD_WRITE         0x40
#define ASC_EEP_CMD_WRITE_ABLE    0x30
#define ASC_EEP_CMD_WRITE_DISABLE 0x00
#define ASC_OVERRUN_BSIZE  0x00000048UL
#define ASC_CTRL_BREAK_ONCE        0x0001
#define ASC_CTRL_BREAK_STAY_IDLE   0x0002
#define ASCV_MSGOUT_BEG         0x0000
#define ASCV_MSGOUT_SDTR_PERIOD (ASCV_MSGOUT_BEG+3)
#define ASCV_MSGOUT_SDTR_OFFSET (ASCV_MSGOUT_BEG+4)
#define ASCV_BREAK_SAVED_CODE   (ushort)0x0006
#define ASCV_MSGIN_BEG          (ASCV_MSGOUT_BEG+8)
#define ASCV_MSGIN_SDTR_PERIOD  (ASCV_MSGIN_BEG+3)
#define ASCV_MSGIN_SDTR_OFFSET  (ASCV_MSGIN_BEG+4)
#define ASCV_SDTR_DATA_BEG      (ASCV_MSGIN_BEG+8)
#define ASCV_SDTR_DONE_BEG      (ASCV_SDTR_DATA_BEG+8)
#define ASCV_MAX_DVC_QNG_BEG    (ushort)0x0020
#define ASCV_BREAK_ADDR           (ushort)0x0028
#define ASCV_BREAK_NOTIFY_COUNT   (ushort)0x002A
#define ASCV_BREAK_CONTROL        (ushort)0x002C
#define ASCV_BREAK_HIT_COUNT      (ushort)0x002E

#define ASCV_ASCDVC_ERR_CODE_W  (ushort)0x0030
#define ASCV_MCODE_CHKSUM_W   (ushort)0x0032
#define ASCV_MCODE_SIZE_W     (ushort)0x0034
#define ASCV_STOP_CODE_B      (ushort)0x0036
#define ASCV_DVC_ERR_CODE_B   (ushort)0x0037
#define ASCV_OVERRUN_PADDR_D  (ushort)0x0038
#define ASCV_OVERRUN_BSIZE_D  (ushort)0x003C
#define ASCV_HALTCODE_W       (ushort)0x0040
#define ASCV_CHKSUM_W         (ushort)0x0042
#define ASCV_MC_DATE_W        (ushort)0x0044
#define ASCV_MC_VER_W         (ushort)0x0046
#define ASCV_NEXTRDY_B        (ushort)0x0048
#define ASCV_DONENEXT_B       (ushort)0x0049
#define ASCV_USE_TAGGED_QNG_B (ushort)0x004A
#define ASCV_SCSIBUSY_B       (ushort)0x004B
#define ASCV_Q_DONE_IN_PROGRESS_B  (ushort)0x004C
#define ASCV_CURCDB_B         (ushort)0x004D
#define ASCV_RCLUN_B          (ushort)0x004E
#define ASCV_BUSY_QHEAD_B     (ushort)0x004F
#define ASCV_DISC1_QHEAD_B    (ushort)0x0050
#define ASCV_DISC_ENABLE_B    (ushort)0x0052
#define ASCV_CAN_TAGGED_QNG_B (ushort)0x0053
#define ASCV_HOSTSCSI_ID_B    (ushort)0x0055
#define ASCV_MCODE_CNTL_B     (ushort)0x0056
#define ASCV_NULL_TARGET_B    (ushort)0x0057
#define ASCV_FREE_Q_HEAD_W    (ushort)0x0058
#define ASCV_DONE_Q_TAIL_W    (ushort)0x005A
#define ASCV_FREE_Q_HEAD_B    (ushort)(ASCV_FREE_Q_HEAD_W+1)
#define ASCV_DONE_Q_TAIL_B    (ushort)(ASCV_DONE_Q_TAIL_W+1)
#define ASCV_HOST_FLAG_B      (ushort)0x005D
#define ASCV_TOTAL_READY_Q_B  (ushort)0x0064
#define ASCV_VER_SERIAL_B     (ushort)0x0065
#define ASCV_HALTCODE_SAVED_W (ushort)0x0066
#define ASCV_WTM_FLAG_B       (ushort)0x0068
#define ASCV_RISC_FLAG_B      (ushort)0x006A
#define ASCV_REQ_SG_LIST_QP   (ushort)0x006B
#define ASC_HOST_FLAG_IN_ISR        0x01
#define ASC_HOST_FLAG_ACK_INT       0x02
#define ASC_RISC_FLAG_GEN_INT      0x01
#define ASC_RISC_FLAG_REQ_SG_LIST  0x02
#define IOP_CTRL         (0x0F)
#define IOP_STATUS       (0x0E)
#define IOP_INT_ACK      IOP_STATUS
#define IOP_REG_IFC      (0x0D)
#define IOP_SYN_OFFSET    (0x0B)
#define IOP_EXTRA_CONTROL (0x0D)
#define IOP_REG_PC        (0x0C)
#define IOP_RAM_ADDR      (0x0A)
#define IOP_RAM_DATA      (0x08)
#define IOP_EEP_DATA      (0x06)
#define IOP_EEP_CMD       (0x07)
#define IOP_VERSION       (0x03)
#define IOP_CONFIG_HIGH   (0x04)
#define IOP_CONFIG_LOW    (0x02)
#define IOP_SIG_BYTE      (0x01)
#define IOP_SIG_WORD      (0x00)
#define IOP_REG_DC1      (0x0E)
#define IOP_REG_DC0      (0x0C)
#define IOP_REG_SB       (0x0B)
#define IOP_REG_DA1      (0x0A)
#define IOP_REG_DA0      (0x08)
#define IOP_REG_SC       (0x09)
#define IOP_DMA_SPEED    (0x07)
#define IOP_REG_FLAG     (0x07)
#define IOP_FIFO_H       (0x06)
#define IOP_FIFO_L       (0x04)
#define IOP_REG_ID       (0x05)
#define IOP_REG_QP       (0x03)
#define IOP_REG_IH       (0x02)
#define IOP_REG_IX       (0x01)
#define IOP_REG_AX       (0x00)
#define IFC_REG_LOCK      (0x00)
#define IFC_REG_UNLOCK    (0x09)
#define IFC_WR_EN_FILTER  (0x10)
#define IFC_RD_NO_EEPROM  (0x10)
#define IFC_SLEW_RATE     (0x20)
#define IFC_ACT_NEG       (0x40)
#define IFC_INP_FILTER    (0x80)
#define IFC_INIT_DEFAULT  (IFC_ACT_NEG | IFC_REG_UNLOCK)
#define SC_SEL   (uchar)(0x80)
#define SC_BSY   (uchar)(0x40)
#define SC_ACK   (uchar)(0x20)
#define SC_REQ   (uchar)(0x10)
#define SC_ATN   (uchar)(0x08)
#define SC_IO    (uchar)(0x04)
#define SC_CD    (uchar)(0x02)
#define SC_MSG   (uchar)(0x01)
#define SEC_SCSI_CTL         (uchar)(0x80)
#define SEC_ACTIVE_NEGATE    (uchar)(0x40)
#define SEC_SLEW_RATE        (uchar)(0x20)
#define SEC_ENABLE_FILTER    (uchar)(0x10)
#define ASC_HALT_EXTMSG_IN     (ushort)0x8000
#define ASC_HALT_CHK_CONDITION (ushort)0x8100
#define ASC_HALT_SS_QUEUE_FULL (ushort)0x8200
#define ASC_HALT_DISABLE_ASYN_USE_SYN_FIX  (ushort)0x8300
#define ASC_HALT_ENABLE_ASYN_USE_SYN_FIX   (ushort)0x8400
#define ASC_HALT_SDTR_REJECTED (ushort)0x4000
#define ASC_MAX_QNO        0xF8
#define ASC_DATA_SEC_BEG   (ushort)0x0080
#define ASC_DATA_SEC_END   (ushort)0x0080
#define ASC_CODE_SEC_BEG   (ushort)0x0080
#define ASC_CODE_SEC_END   (ushort)0x0080
#define ASC_QADR_BEG       (0x4000)
#define ASC_QADR_USED      (ushort)(ASC_MAX_QNO * 64)
#define ASC_QADR_END       (ushort)0x7FFF
#define ASC_QLAST_ADR      (ushort)0x7FC0
#define ASC_QBLK_SIZE      0x40
#define ASC_BIOS_DATA_QBEG 0xF8
#define ASC_MIN_ACTIVE_QNO 0x01
#define ASC_QLINK_END      0xFF
#define ASC_EEPROM_WORDS   0x10
#define ASC_MAX_MGS_LEN    0x10
#define ASC_BIOS_ADDR_DEF  0xDC00
#define ASC_BIOS_SIZE      0x3800
#define ASC_BIOS_RAM_OFF   0x3800
#define ASC_BIOS_RAM_SIZE  0x800
#define ASC_BIOS_MIN_ADDR  0xC000
#define ASC_BIOS_MAX_ADDR  0xEC00
#define ASC_BIOS_BANK_SIZE 0x0400
#define ASC_MCODE_START_ADDR  0x0080
#define ASC_CFG0_HOST_INT_ON    0x0020
#define ASC_CFG0_BIOS_ON        0x0040
#define ASC_CFG0_VERA_BURST_ON  0x0080
#define ASC_CFG0_SCSI_PARITY_ON 0x0800
#define ASC_CFG1_SCSI_TARGET_ON 0x0080
#define ASC_CFG1_LRAM_8BITS_ON  0x0800
#define ASC_CFG_MSW_CLR_MASK    0x30C0
#define CSW_TEST1             (ASC_CS_TYPE)0x8000
#define CSW_AUTO_CONFIG       (ASC_CS_TYPE)0x4000
#define CSW_RESERVED1         (ASC_CS_TYPE)0x2000
#define CSW_IRQ_WRITTEN       (ASC_CS_TYPE)0x1000
#define CSW_33MHZ_SELECTED    (ASC_CS_TYPE)0x0800
#define CSW_TEST2             (ASC_CS_TYPE)0x0400
#define CSW_TEST3             (ASC_CS_TYPE)0x0200
#define CSW_RESERVED2         (ASC_CS_TYPE)0x0100
#define CSW_DMA_DONE          (ASC_CS_TYPE)0x0080
#define CSW_FIFO_RDY          (ASC_CS_TYPE)0x0040
#define CSW_EEP_READ_DONE     (ASC_CS_TYPE)0x0020
#define CSW_HALTED            (ASC_CS_TYPE)0x0010
#define CSW_SCSI_RESET_ACTIVE (ASC_CS_TYPE)0x0008
#define CSW_PARITY_ERR        (ASC_CS_TYPE)0x0004
#define CSW_SCSI_RESET_LATCH  (ASC_CS_TYPE)0x0002
#define CSW_INT_PENDING       (ASC_CS_TYPE)0x0001
#define CIW_CLR_SCSI_RESET_INT (ASC_CS_TYPE)0x1000
#define CIW_INT_ACK      (ASC_CS_TYPE)0x0100
#define CIW_TEST1        (ASC_CS_TYPE)0x0200
#define CIW_TEST2        (ASC_CS_TYPE)0x0400
#define CIW_SEL_33MHZ    (ASC_CS_TYPE)0x0800
#define CIW_IRQ_ACT      (ASC_CS_TYPE)0x1000
#define CC_CHIP_RESET   (uchar)0x80
#define CC_SCSI_RESET   (uchar)0x40
#define CC_HALT         (uchar)0x20
#define CC_SINGLE_STEP  (uchar)0x10
#define CC_DMA_ABLE     (uchar)0x08
#define CC_TEST         (uchar)0x04
#define CC_BANK_ONE     (uchar)0x02
#define CC_DIAG         (uchar)0x01
#define ASC_1000_ID0W      0x04C1
#define ASC_1000_ID0W_FIX  0x00C1
#define ASC_1000_ID1B      0x25
#define ASC_EISA_BIG_IOP_GAP   (0x1C30-0x0C50)
#define ASC_EISA_SMALL_IOP_GAP (0x0020)
#define ASC_EISA_MIN_IOP_ADDR  (0x0C30)
#define ASC_EISA_MAX_IOP_ADDR  (0xFC50)
#define ASC_EISA_REV_IOP_MASK  (0x0C83)
#define ASC_EISA_PID_IOP_MASK  (0x0C80)
#define ASC_EISA_CFG_IOP_MASK  (0x0C86)
#define ASC_GET_EISA_SLOT(iop)  (PortAddr)((iop) & 0xF000)
#define ASC_EISA_ID_740    0x01745004UL
#define ASC_EISA_ID_750    0x01755004UL
#define INS_HALTINT        (ushort)0x6281
#define INS_HALT           (ushort)0x6280
#define INS_SINT           (ushort)0x6200
#define INS_RFLAG_WTM      (ushort)0x7380
#define ASC_MC_SAVE_CODE_WSIZE  0x500
#define ASC_MC_SAVE_DATA_WSIZE  0x40

typedef struct asc_mc_saved {
    ushort              data[ASC_MC_SAVE_DATA_WSIZE];
    ushort              code[ASC_MC_SAVE_CODE_WSIZE];
} ASC_MC_SAVED;

#define AscGetQDoneInProgress(port)         AscReadLramByte((port), ASCV_Q_DONE_IN_PROGRESS_B)
#define AscPutQDoneInProgress(port, val)    AscWriteLramByte((port), ASCV_Q_DONE_IN_PROGRESS_B, val)
#define AscGetVarFreeQHead(port)            AscReadLramWord((port), ASCV_FREE_Q_HEAD_W)
#define AscGetVarDoneQTail(port)            AscReadLramWord((port), ASCV_DONE_Q_TAIL_W)
#define AscPutVarFreeQHead(port, val)       AscWriteLramWord((port), ASCV_FREE_Q_HEAD_W, val)
#define AscPutVarDoneQTail(port, val)       AscWriteLramWord((port), ASCV_DONE_Q_TAIL_W, val)
#define AscGetRiscVarFreeQHead(port)        AscReadLramByte((port), ASCV_NEXTRDY_B)
#define AscGetRiscVarDoneQTail(port)        AscReadLramByte((port), ASCV_DONENEXT_B)
#define AscPutRiscVarFreeQHead(port, val)   AscWriteLramByte((port), ASCV_NEXTRDY_B, val)
#define AscPutRiscVarDoneQTail(port, val)   AscWriteLramByte((port), ASCV_DONENEXT_B, val)
#define AscPutMCodeSDTRDoneAtID(port, id, data)  AscWriteLramByte((port), (ushort)((ushort)ASCV_SDTR_DONE_BEG+(ushort)id), (data)) ;
#define AscGetMCodeSDTRDoneAtID(port, id)        AscReadLramByte((port), (ushort)((ushort)ASCV_SDTR_DONE_BEG+(ushort)id)) ;
#define AscPutMCodeInitSDTRAtID(port, id, data)  AscWriteLramByte((port), (ushort)((ushort)ASCV_SDTR_DATA_BEG+(ushort)id), data) ;
#define AscGetMCodeInitSDTRAtID(port, id)        AscReadLramByte((port), (ushort)((ushort)ASCV_SDTR_DATA_BEG+(ushort)id)) ;
#define AscSynIndexToPeriod(index)        (uchar)(asc_dvc->sdtr_period_tbl[ (index) ])
#define AscGetChipSignatureByte(port)     (uchar)inp((port)+IOP_SIG_BYTE)
#define AscGetChipSignatureWord(port)     (ushort)inpw((port)+IOP_SIG_WORD)
#define AscGetChipVerNo(port)             (uchar)inp((port)+IOP_VERSION)
#define AscGetChipCfgLsw(port)            (ushort)inpw((port)+IOP_CONFIG_LOW)
#define AscGetChipCfgMsw(port)            (ushort)inpw((port)+IOP_CONFIG_HIGH)
#define AscSetChipCfgLsw(port, data)      outpw((port)+IOP_CONFIG_LOW, data)
#define AscSetChipCfgMsw(port, data)      outpw((port)+IOP_CONFIG_HIGH, data)
#define AscGetChipEEPCmd(port)            (uchar)inp((port)+IOP_EEP_CMD)
#define AscSetChipEEPCmd(port, data)      outp((port)+IOP_EEP_CMD, data)
#define AscGetChipEEPData(port)           (ushort)inpw((port)+IOP_EEP_DATA)
#define AscSetChipEEPData(port, data)     outpw((port)+IOP_EEP_DATA, data)
#define AscGetChipLramAddr(port)          (ushort)inpw((PortAddr)((port)+IOP_RAM_ADDR))
#define AscSetChipLramAddr(port, addr)    outpw((PortAddr)((port)+IOP_RAM_ADDR), addr)
#define AscGetChipLramData(port)          (ushort)inpw((port)+IOP_RAM_DATA)
#define AscSetChipLramData(port, data)    outpw((port)+IOP_RAM_DATA, data)
#define AscGetChipLramDataNoSwap(port)         (ushort)inpw_noswap((port)+IOP_RAM_DATA)
#define AscSetChipLramDataNoSwap(port, data)   outpw_noswap((port)+IOP_RAM_DATA, data)
#define AscGetChipIFC(port)               (uchar)inp((port)+IOP_REG_IFC)
#define AscSetChipIFC(port, data)          outp((port)+IOP_REG_IFC, data)
#define AscGetChipStatus(port)            (ASC_CS_TYPE)inpw((port)+IOP_STATUS)
#define AscSetChipStatus(port, cs_val)    outpw((port)+IOP_STATUS, cs_val)
#define AscGetChipControl(port)           (uchar)inp((port)+IOP_CTRL)
#define AscSetChipControl(port, cc_val)   outp((port)+IOP_CTRL, cc_val)
#define AscGetChipSyn(port)               (uchar)inp((port)+IOP_SYN_OFFSET)
#define AscSetChipSyn(port, data)         outp((port)+IOP_SYN_OFFSET, data)
#define AscSetPCAddr(port, data)          outpw((port)+IOP_REG_PC, data)
#define AscGetPCAddr(port)                (ushort)inpw((port)+IOP_REG_PC)
#define AscIsIntPending(port)             (AscGetChipStatus(port) & (CSW_INT_PENDING | CSW_SCSI_RESET_LATCH))
#define AscGetChipScsiID(port)            ((AscGetChipCfgLsw(port) >> 8) & ASC_MAX_TID)
#define AscGetExtraControl(port)          (uchar)inp((port)+IOP_EXTRA_CONTROL)
#define AscSetExtraControl(port, data)    outp((port)+IOP_EXTRA_CONTROL, data)
#define AscReadChipAX(port)               (ushort)inpw((port)+IOP_REG_AX)
#define AscWriteChipAX(port, data)        outpw((port)+IOP_REG_AX, data)
#define AscReadChipIX(port)               (uchar)inp((port)+IOP_REG_IX)
#define AscWriteChipIX(port, data)        outp((port)+IOP_REG_IX, data)
#define AscReadChipIH(port)               (ushort)inpw((port)+IOP_REG_IH)
#define AscWriteChipIH(port, data)        outpw((port)+IOP_REG_IH, data)
#define AscReadChipQP(port)               (uchar)inp((port)+IOP_REG_QP)
#define AscWriteChipQP(port, data)        outp((port)+IOP_REG_QP, data)
#define AscReadChipFIFO_L(port)           (ushort)inpw((port)+IOP_REG_FIFO_L)
#define AscWriteChipFIFO_L(port, data)    outpw((port)+IOP_REG_FIFO_L, data)
#define AscReadChipFIFO_H(port)           (ushort)inpw((port)+IOP_REG_FIFO_H)
#define AscWriteChipFIFO_H(port, data)    outpw((port)+IOP_REG_FIFO_H, data)
#define AscReadChipDmaSpeed(port)         (uchar)inp((port)+IOP_DMA_SPEED)
#define AscWriteChipDmaSpeed(port, data)  outp((port)+IOP_DMA_SPEED, data)
#define AscReadChipDA0(port)              (ushort)inpw((port)+IOP_REG_DA0)
#define AscWriteChipDA0(port)             outpw((port)+IOP_REG_DA0, data)
#define AscReadChipDA1(port)              (ushort)inpw((port)+IOP_REG_DA1)
#define AscWriteChipDA1(port)             outpw((port)+IOP_REG_DA1, data)
#define AscReadChipDC0(port)              (ushort)inpw((port)+IOP_REG_DC0)
#define AscWriteChipDC0(port)             outpw((port)+IOP_REG_DC0, data)
#define AscReadChipDC1(port)              (ushort)inpw((port)+IOP_REG_DC1)
#define AscWriteChipDC1(port)             outpw((port)+IOP_REG_DC1, data)
#define AscReadChipDvcID(port)            (uchar)inp((port)+IOP_REG_ID)
#define AscWriteChipDvcID(port, data)     outp((port)+IOP_REG_ID, data)

STATIC int       AscWriteEEPCmdReg(PortAddr iop_base, uchar cmd_reg);
STATIC int       AscWriteEEPDataReg(PortAddr iop_base, ushort data_reg);
STATIC void      AscWaitEEPRead(void);
STATIC void      AscWaitEEPWrite(void);
STATIC ushort    AscReadEEPWord(PortAddr, uchar);
STATIC ushort    AscWriteEEPWord(PortAddr, uchar, ushort);
STATIC ushort    AscGetEEPConfig(PortAddr, ASCEEP_CONFIG *, ushort);
STATIC int       AscSetEEPConfigOnce(PortAddr, ASCEEP_CONFIG *, ushort);
STATIC int       AscSetEEPConfig(PortAddr, ASCEEP_CONFIG *, ushort);
STATIC int       AscStartChip(PortAddr);
STATIC int       AscStopChip(PortAddr);
STATIC void      AscSetChipIH(PortAddr, ushort);
STATIC int       AscIsChipHalted(PortAddr);
STATIC void      AscAckInterrupt(PortAddr);
STATIC void      AscDisableInterrupt(PortAddr);
STATIC void      AscEnableInterrupt(PortAddr);
STATIC void      AscSetBank(PortAddr, uchar);
STATIC int       AscResetChipAndScsiBus(PortAddr);
STATIC ushort    AscGetIsaDmaChannel(PortAddr);
STATIC ushort    AscSetIsaDmaChannel(PortAddr, ushort);
STATIC uchar     AscSetIsaDmaSpeed(PortAddr, uchar);
STATIC uchar     AscGetIsaDmaSpeed(PortAddr);
STATIC uchar     AscReadLramByte(PortAddr, ushort);
STATIC ushort    AscReadLramWord(PortAddr, ushort);
STATIC ulong     AscReadLramDWord(PortAddr, ushort);
STATIC void      AscWriteLramWord(PortAddr, ushort, ushort);
STATIC void      AscWriteLramDWord(PortAddr, ushort, ulong);
STATIC void      AscWriteLramByte(PortAddr, ushort, uchar);
STATIC ulong     AscMemSumLramWord(PortAddr, ushort, rint);
STATIC void      AscMemWordSetLram(PortAddr, ushort, ushort, rint);
STATIC void      AscMemWordCopyToLram(PortAddr, ushort, ushort *, int);
STATIC void      AscMemDWordCopyToLram(PortAddr, ushort, ulong *, int);
STATIC void      AscMemWordCopyFromLram(PortAddr, ushort, ushort *, int);
STATIC ushort    AscInitAscDvcVar(ASC_DVC_VAR asc_ptr_type *);
STATIC ushort    AscInitFromEEP(ASC_DVC_VAR asc_ptr_type *);
STATIC ushort    AscInitFromAscDvcVar(ASC_DVC_VAR asc_ptr_type *);
STATIC ushort    AscInitMicroCodeVar(ASC_DVC_VAR asc_ptr_type * asc_dvc);
STATIC void      AscInitPollIsrCallBack(ASC_DVC_VAR asc_ptr_type *,
                    ASC_QDONE_INFO *);
STATIC int       AscTestExternalLram(ASC_DVC_VAR asc_ptr_type *);
STATIC uchar     AscMsgOutSDTR(ASC_DVC_VAR asc_ptr_type *, uchar, uchar);
STATIC uchar     AscCalSDTRData(ASC_DVC_VAR asc_ptr_type *, uchar, uchar);
STATIC void      AscSetChipSDTR(PortAddr, uchar, uchar);
STATIC uchar     AscGetSynPeriodIndex(ASC_DVC_VAR asc_ptr_type *, ruchar);
STATIC uchar     AscAllocFreeQueue(PortAddr, uchar);
STATIC uchar     AscAllocMultipleFreeQueue(PortAddr, uchar, uchar);
STATIC int       AscRiscHaltedAbortSRB(ASC_DVC_VAR asc_ptr_type *, ulong);
#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,89)
STATIC int       AscRiscHaltedAbortTIX(ASC_DVC_VAR asc_ptr_type *, uchar);
#endif /* version >= v1.3.89 */
STATIC int       AscHostReqRiscHalt(PortAddr);
STATIC int       AscStopQueueExe(PortAddr);
STATIC int       AscStartQueueExe(PortAddr);
#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,89)
STATIC int       AscCleanUpDiscQueue(PortAddr);
#endif /* version >= v1.3.89 */
STATIC int       AscCleanUpBusyQueue(PortAddr);
STATIC int       AscWaitTixISRDone(ASC_DVC_VAR asc_ptr_type *, uchar);
STATIC int       AscWaitISRDone(ASC_DVC_VAR asc_ptr_type *);
STATIC ulong     AscGetOnePhyAddr(ASC_DVC_VAR asc_ptr_type *, uchar *,
                    ulong);
STATIC int       AscSendScsiQueue(ASC_DVC_VAR asc_ptr_type * asc_dvc,
                    ASC_SCSI_Q * scsiq,
                    uchar n_q_required);
STATIC int       AscPutReadyQueue(ASC_DVC_VAR asc_ptr_type *,
                    ASC_SCSI_Q *, uchar);
STATIC int       AscPutReadySgListQueue(ASC_DVC_VAR asc_ptr_type *,
                    ASC_SCSI_Q *, uchar);
STATIC int       AscSetChipSynRegAtID(PortAddr, uchar, uchar);
STATIC int       AscSetRunChipSynRegAtID(PortAddr, uchar, uchar);
STATIC ushort    AscInitLram(ASC_DVC_VAR asc_ptr_type *);
STATIC int       AscReInitLram(ASC_DVC_VAR asc_ptr_type *);
STATIC ushort    AscInitQLinkVar(ASC_DVC_VAR asc_ptr_type *);
STATIC int       AscSetLibErrorCode(ASC_DVC_VAR asc_ptr_type *, ushort);
#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,89)
STATIC int       _AscWaitQDone(PortAddr, ASC_SCSI_Q *);
#endif /* version >= v1.3.89 */
STATIC int       AscIsrChipHalted(ASC_DVC_VAR asc_ptr_type *);
STATIC uchar     _AscCopyLramScsiDoneQ(PortAddr, ushort,
                    ASC_QDONE_INFO *, ulong);
STATIC int       AscIsrQDone(ASC_DVC_VAR asc_ptr_type *);
STATIC int       AscScsiSetupCmdQ(ASC_DVC_VAR asc_ptr_type *,
                    ASC_SCSI_REQ_Q *, uchar *, ulong);
STATIC int       AscScsiInquiry(ASC_DVC_VAR asc_ptr_type *,
                    ASC_SCSI_REQ_Q *, uchar *, int);
STATIC int       AscScsiTestUnitReady(ASC_DVC_VAR asc_ptr_type *,
                    ASC_SCSI_REQ_Q *);
STATIC int       AscScsiStartStopUnit(ASC_DVC_VAR asc_ptr_type *,
                    ASC_SCSI_REQ_Q *, uchar);
STATIC int       AscScsiReadCapacity(ASC_DVC_VAR asc_ptr_type *,
                    ASC_SCSI_REQ_Q *, uchar *);
STATIC ulong     *swapfarbuf4(uchar *);
STATIC int       PollQueueDone(ASC_DVC_VAR asc_ptr_type *,
                    ASC_SCSI_REQ_Q *, int);
STATIC int       PollScsiReadCapacity(ASC_DVC_VAR asc_ptr_type *,
                    ASC_SCSI_REQ_Q *, ASC_CAP_INFO *);
STATIC int       PollScsiInquiry(ASC_DVC_VAR asc_ptr_type *,
                    ASC_SCSI_REQ_Q *, uchar *, int);
STATIC int       PollScsiTestUnitReady(ASC_DVC_VAR asc_ptr_type *,
                    ASC_SCSI_REQ_Q *);
STATIC int       PollScsiStartUnit(ASC_DVC_VAR asc_ptr_type *,
                    ASC_SCSI_REQ_Q *);
STATIC int       InitTestUnitReady(ASC_DVC_VAR asc_ptr_type *,
                    ASC_SCSI_REQ_Q *);
STATIC int       AscPollQDone(ASC_DVC_VAR asc_ptr_type *,
                    ASC_SCSI_REQ_Q *, int);
STATIC int       AscCompareString(uchar *, uchar *, int);
STATIC ushort    AscGetEisaChipCfg(PortAddr);
STATIC ulong     AscGetEisaProductID(PortAddr);
STATIC PortAddr  AscSearchIOPortAddrEISA(PortAddr);
STATIC uchar     AscGetChipScsiCtrl(PortAddr);
STATIC uchar     AscSetChipScsiID(PortAddr, uchar);
STATIC uchar     AscGetChipVersion(PortAddr, ushort);
STATIC ushort    AscGetChipBusType(PortAddr);
STATIC ulong     AscLoadMicroCode(PortAddr, ushort, ushort *, ushort);
STATIC int       AscFindSignature(PortAddr);
STATIC PortAddr  AscSearchIOPortAddr11(PortAddr);
STATIC void      AscToggleIRQAct(PortAddr);
STATIC void      AscSetISAPNPWaitForKey(void);
STATIC uchar     AscGetChipIRQ(PortAddr, ushort);
STATIC uchar     AscSetChipIRQ(PortAddr, uchar, ushort);
STATIC ushort    AscGetChipBiosAddress(PortAddr, ushort);
STATIC int       DvcEnterCritical(void);
STATIC void      DvcLeaveCritical(int);
STATIC void      DvcInPortWords(PortAddr, ushort *, int);
STATIC void      DvcOutPortWords(PortAddr, ushort *, int);
STATIC void      DvcOutPortDWords(PortAddr, ulong *, int);
STATIC uchar     DvcReadPCIConfigByte(ASC_DVC_VAR asc_ptr_type *, ushort);
STATIC void      DvcWritePCIConfigByte(ASC_DVC_VAR asc_ptr_type *,
                    ushort, uchar);
STATIC ushort      AscGetChipBiosAddress(PortAddr, ushort);
STATIC void      DvcSleepMilliSecond(ulong);
STATIC void      DvcDelayNanoSecond(ASC_DVC_VAR asc_ptr_type *, ulong);
STATIC ulong     DvcGetSGList(ASC_DVC_VAR asc_ptr_type *, uchar *,
                    ulong, ASC_SG_HEAD *);
STATIC void      DvcPutScsiQ(PortAddr, ushort, ushort *, int);
STATIC void      DvcGetQinfo(PortAddr, ushort, ushort *, int);
STATIC PortAddr  AscSearchIOPortAddr(PortAddr, ushort);
STATIC ushort    AscInitGetConfig(ASC_DVC_VAR asc_ptr_type *);
STATIC ushort    AscInitSetConfig(ASC_DVC_VAR asc_ptr_type *);
STATIC ushort    AscInitAsc1000Driver(ASC_DVC_VAR asc_ptr_type *);
STATIC int       AscInitPollBegin(ASC_DVC_VAR asc_ptr_type *);
STATIC int       AscInitPollEnd(ASC_DVC_VAR asc_ptr_type *);
STATIC int       AscInitPollTarget(ASC_DVC_VAR asc_ptr_type *,
                     ASC_SCSI_REQ_Q *, ASC_SCSI_INQUIRY *, ASC_CAP_INFO *);
STATIC int       AscExeScsiQueue(ASC_DVC_VAR asc_ptr_type *, ASC_SCSI_Q *);
STATIC int       AscISR(ASC_DVC_VAR asc_ptr_type *);
STATIC uint      AscGetNumOfFreeQueue(ASC_DVC_VAR asc_ptr_type *, uchar,
                    uchar);
STATIC int       AscSgListToQueue(int);
STATIC int       AscAbortSRB(ASC_DVC_VAR asc_ptr_type *, ulong);
#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,89)
STATIC int       AscResetDevice(ASC_DVC_VAR asc_ptr_type *, uchar);
#endif /* version >= v1.3.89 */
STATIC int       AscResetSB(ASC_DVC_VAR asc_ptr_type *);
STATIC void      AscEnableIsaDma(uchar);
STATIC ulong     AscGetMaxDmaCount(ushort);


/*
 * --- Driver Constants and Macros
 */

#define ASC_NUM_BOARD_SUPPORTED 4
#define ASC_NUM_BUS             4

/* Reference Scsi_Host hostdata */
#define ASC_BOARDP(host) ((asc_board_t *) &((host)->hostdata))

/* asc_board_t flags */
#define ASC_HOST_IN_RESET       0x01
#define ASC_HOST_IN_ABORT       0x02

#define NO_ISA_DMA              0xff        /* No ISA DMA Channel Used */

/*
 * If the Linux kernel version supports throwing away initialization code
 * and data after loading, define macros for this purpose. These macros
 * are not used when the driver is built as a module, cf. linux/init.h.
 */
#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(2,1,23)
#define ASC_INITFUNC(func)      __initfunc(func)
#define ASC_INITDATA            __initdata
#define ASC_INIT                __init
#else /* version >= v2.1.23 */
#define ASC_INITFUNC(func)      func
#define ASC_INITDATA
#define ASC_INIT
#endif /* version >= v2.1.23 */

#define ASC_INFO_SIZE           128            /* advansys_info() line size */

/* /proc/scsi/advansys/[0...] related definitions */
#define ASC_PRTBUF_SIZE         2048
#define ASC_PRTLINE_SIZE        160

#define ASC_PRT_NEXT() \
    if (cp) { \
        totlen += len; \
        leftlen -= len; \
        if (leftlen == 0) { \
            return totlen; \
        } \
        cp += len; \
    }

#define ASC_MIN(a, b) (((a) < (b)) ? (a) : (b))

/* Asc Library return codes */
#define ASC_TRUE        1
#define ASC_FALSE       0
#define ASC_NOERROR     1
#define ASC_BUSY        0
#define ASC_ERROR       (-1)

/* Scsi_Cmnd function return codes */
#define STATUS_BYTE(byte)   (byte)
#define MSG_BYTE(byte)      ((byte) << 8)
#define HOST_BYTE(byte)     ((byte) << 16)
#define DRIVER_BYTE(byte)   ((byte) << 24)

/*
 * The following definitions and macros are OS independent interfaces to
 * the queue functions:
 *  REQ - SCSI request structure
 *  REQP - pointer to SCSI request structure
 *  REQPTID(reqp) - reqp's target id
 *  REQPNEXT(reqp) - reqp's next pointer
 *  REQPNEXTP(reqp) - pointer to reqp's next pointer
 *  REQPTIME(reqp) - reqp's time stamp value
 *  REQTIMESTAMP() - system time stamp value
 */
typedef Scsi_Cmnd            REQ, *REQP;
#define REQPNEXT(reqp)        ((REQP) ((reqp)->host_scribble))
#define REQPNEXTP(reqp)        ((REQP *) &((reqp)->host_scribble))
#define REQPTID(reqp)        ((reqp)->target)
#define REQPTIME(reqp)        ((reqp)->SCp.this_residual)
#define REQTIMESTAMP()        (jiffies)

#define REQTIMESTAT(function, ascq, reqp, tid) \
{ \
    /*
     * If the request time stamp is less than the system time stamp, then \
     * maybe the system time stamp wrapped. Set the request time to zero.\
     */ \
    if (REQPTIME(reqp) <= REQTIMESTAMP()) { \
        REQPTIME(reqp) = REQTIMESTAMP() - REQPTIME(reqp); \
    } else { \
        /* Indicate an error occurred with the assertion. */ \
        ASC_ASSERT(REQPTIME(reqp) <= REQTIMESTAMP()); \
        REQPTIME(reqp) = 0; \
    } \
    /* Handle first minimum time case without external initialization. */ \
    if (((ascq)->q_tot_cnt[tid] == 1) ||  \
        (REQPTIME(reqp) < (ascq)->q_min_tim[tid])) { \
            (ascq)->q_min_tim[tid] = REQPTIME(reqp); \
            ASC_DBG3(1, "%s: new q_min_tim[%d] %u\n", \
                (function), (tid), (ascq)->q_min_tim[tid]); \
        } \
    if (REQPTIME(reqp) > (ascq)->q_max_tim[tid]) { \
        (ascq)->q_max_tim[tid] = REQPTIME(reqp); \
        ASC_DBG3(1, "%s: new q_max_tim[%d] %u\n", \
            (function), tid, (ascq)->q_max_tim[tid]); \
    } \
    (ascq)->q_tot_tim[tid] += REQPTIME(reqp); \
    /* Reset the time stamp field. */ \
    REQPTIME(reqp) = 0; \
}

/* asc_enqueue() flags */
#define ASC_FRONT        1
#define ASC_BACK        2

/* asc_dequeue_list() argument */
#define ASC_TID_ALL        (-1)

/* Return non-zero, if the queue is empty. */
#define ASC_QUEUE_EMPTY(ascq)    ((ascq)->q_tidmask == 0)

/* PCI configuration declarations */

#define PCI_BASE_CLASS_PREDEFINED               0x00
#define PCI_BASE_CLASS_MASS_STORAGE             0x01
#define PCI_BASE_CLASS_NETWORK                  0x02
#define PCI_BASE_CLASS_DISPLAY                  0x03
#define PCI_BASE_CLASS_MULTIMEDIA               0x04
#define PCI_BASE_CLASS_MEMORY_CONTROLLER        0x05
#define PCI_BASE_CLASS_BRIDGE_DEVICE            0x06

/* MASS STORAGE */
#define PCI_SUB_CLASS_SCSI_CONTROLLER           0x00
#define PCI_SUB_CLASS_IDE_CONTROLLER            0x01
#define PCI_SUB_CLASS_FLOPPY_DISK_CONTROLLER    0x02
#define PCI_SUB_CLASS_IPI_BUS_CONTROLLER        0x03
#define PCI_SUB_CLASS_OTHER_MASS_CONTROLLER     0x80

/* NETWORK CONTROLLER */
#define PCI_SUB_CLASS_ETHERNET_CONTROLLER       0x00
#define PCI_SUB_CLASS_TOKEN_RING_CONTROLLER     0x01
#define PCI_SUB_CLASS_FDDI_CONTROLLER           0x02
#define PCI_SUB_CLASS_OTHER_NETWORK_CONTROLLER  0x80

/* DISPLAY CONTROLLER */
#define PCI_SUB_CLASS_VGA_CONTROLLER            0x00
#define PCI_SUB_CLASS_XGA_CONTROLLER            0x01
#define PCI_SUB_CLASS_OTHER_DISPLAY_CONTROLLER  0x80

/* MULTIMEDIA CONTROLLER */
#define PCI_SUB_CLASS_VIDEO_DEVICE              0x00
#define PCI_SUB_CLASS_AUDIO_DEVICE              0x01
#define PCI_SUB_CLASS_OTHER_MULTIMEDIA_DEVICE   0x80

/* MEMORY CONTROLLER */
#define PCI_SUB_CLASS_RAM_CONTROLLER            0x00
#define PCI_SUB_CLASS_FLASH_CONTROLLER          0x01
#define PCI_SUB_CLASS_OTHER_MEMORY_CONTROLLER   0x80

/* BRIDGE CONTROLLER */
#define PCI_SUB_CLASS_HOST_BRIDGE_CONTROLLER    0x00
#define PCI_SUB_CLASS_ISA_BRIDGE_CONTROLLER     0x01
#define PCI_SUB_CLASS_EISA_BRIDGE_CONTROLLER    0x02
#define PCI_SUB_CLASS_MC_BRIDGE_CONTROLLER      0x03
#define PCI_SUB_CLASS_PCI_TO_PCI_BRIDGE_CONTROLLER    0x04
#define PCI_SUB_CLASS_PCMCIA_BRIDGE_CONTROLLER  0x05
#define PCI_SUB_CLASS_OTHER_BRIDGE_CONTROLLER   0x80

#define PCI_MAX_SLOT            0x1F
#define PCI_MAX_BUS             0xFF
#define PCI_IOADDRESS_MASK      0xFFFE
#define ASC_PCI_VENDORID        0x10CD
#define ASC_PCI_DEVICE_ID_1100  0x1100
#define ASC_PCI_DEVICE_ID_1200  0x1200
#define ASC_PCI_DEVICE_ID_1300  0x1300

/* PCI IO Port Addresses to generate special cycle */

#define PCI_CONFIG_ADDRESS_MECH1          0x0CF8
#define PCI_CONFIG_DATA_MECH1             0x0CFC

#define PCI_CONFIG_FORWARD_REGISTER       0x0CFA    /* 0=type 0; 1=type 1; */

#define PCI_CONFIG_BUS_NUMBER_MASK        0x00FF0000
#define PCI_CONFIG_DEVICE_FUNCTION_MASK   0x0000FF00
#define PCI_CONFIG_REGISTER_NUMBER_MASK   0x000000F8

#define PCI_DEVICE_FOUND                0x0000
#define PCI_DEVICE_NOT_FOUND            0xffff

#define SUBCLASS_OFFSET         0x0A
#define CLASSCODE_OFFSET        0x0B
#define VENDORID_OFFSET         0x00
#define DEVICEID_OFFSET         0x02

#ifndef ADVANSYS_STATS
#define ASC_STATS(shp, counter)
#define ASC_STATS_ADD(shp, counter, count)
#else /* ADVANSYS_STATS */
#define ASC_STATS(shp, counter) \
    (ASC_BOARDP(shp)->asc_stats.counter++)

#define ASC_STATS_ADD(shp, counter, count) \
    (ASC_BOARDP(shp)->asc_stats.counter += (count))
#endif /* ADVANSYS_STATS */

#define ASC_CEILING(val, unit) (((val) + ((unit) - 1))/(unit))

/* If the result wraps when calculating tenths, return 0. */
#define ASC_TENTHS(num, den) \
    (((10 * ((num)/(den))) > (((num) * 10)/(den))) ? \
    0 : ((((num) * 10)/(den)) - (10 * ((num)/(den)))))

/*
 * Display a message to the console.
 */
#define ASC_PRINT(s) \
    { \
        printk("advansys: "); \
        printk(s); \
    }

#define ASC_PRINT1(s, a1) \
    { \
        printk("advansys: "); \
        printk((s), (a1)); \
    }

#define ASC_PRINT2(s, a1, a2) \
    { \
        printk("advansys: "); \
        printk((s), (a1), (a2)); \
    }

#define ASC_PRINT3(s, a1, a2, a3) \
    { \
        printk("advansys: "); \
        printk((s), (a1), (a2), (a3)); \
    }

#define ASC_PRINT4(s, a1, a2, a3, a4) \
    { \
        printk("advansys: "); \
        printk((s), (a1), (a2), (a3), (a4)); \
    }


#ifndef ADVANSYS_DEBUG

#define ASC_DBG(lvl, s)
#define ASC_DBG1(lvl, s, a1)
#define ASC_DBG2(lvl, s, a1, a2)
#define ASC_DBG3(lvl, s, a1, a2, a3)
#define ASC_DBG4(lvl, s, a1, a2, a3, a4)
#define ASC_DBG_PRT_SCSI_HOST(lvl, s)
#define ASC_DBG_PRT_SCSI_CMND(lvl, s)
#define ASC_DBG_PRT_SCSI_Q(lvl, scsiqp)
#define ASC_DBG_PRT_QDONE_INFO(lvl, qdone)
#define ASC_DBG_PRT_HEX(lvl, name, start, length)
#define ASC_DBG_PRT_CDB(lvl, cdb, len)
#define ASC_DBG_PRT_SENSE(lvl, sense, len)
#define ASC_DBG_PRT_INQUIRY(lvl, inq, len)

#else /* ADVANSYS_DEBUG */

/*
 * Debugging Message Levels:
 * 0: Errors Only
 * 1: High-Level Tracing
 * 2-N: Verbose Tracing
 */

#define ASC_DBG(lvl, s) \
    { \
        if (asc_dbglvl >= (lvl)) { \
            printk(s); \
        } \
    }

#define ASC_DBG1(lvl, s, a1) \
    { \
        if (asc_dbglvl >= (lvl)) { \
            printk((s), (a1)); \
        } \
    }

#define ASC_DBG2(lvl, s, a1, a2) \
    { \
        if (asc_dbglvl >= (lvl)) { \
            printk((s), (a1), (a2)); \
        } \
    }

#define ASC_DBG3(lvl, s, a1, a2, a3) \
    { \
        if (asc_dbglvl >= (lvl)) { \
            printk((s), (a1), (a2), (a3)); \
        } \
    }

#define ASC_DBG4(lvl, s, a1, a2, a3, a4) \
    { \
        if (asc_dbglvl >= (lvl)) { \
            printk((s), (a1), (a2), (a3), (a4)); \
        } \
    }

#define ASC_DBG_PRT_SCSI_HOST(lvl, s) \
    { \
        if (asc_dbglvl >= (lvl)) { \
            asc_prt_scsi_host(s); \
        } \
    }

#define ASC_DBG_PRT_SCSI_CMND(lvl, s) \
    { \
        if (asc_dbglvl >= (lvl)) { \
            asc_prt_scsi_cmnd(s); \
        } \
    }

#define ASC_DBG_PRT_SCSI_Q(lvl, scsiqp) \
    { \
        if (asc_dbglvl >= (lvl)) { \
            asc_prt_scsi_q(scsiqp); \
        } \
    }

#define ASC_DBG_PRT_QDONE_INFO(lvl, qdone) \
    { \
        if (asc_dbglvl >= (lvl)) { \
            asc_prt_qdone_info(qdone); \
        } \
    }

#define ASC_DBG_PRT_HEX(lvl, name, start, length) \
    { \
        if (asc_dbglvl >= (lvl)) { \
            asc_prt_hex((name), (start), (length)); \
        } \
    }

#define ASC_DBG_PRT_CDB(lvl, cdb, len) \
        ASC_DBG_PRT_HEX((lvl), "CDB", (uchar *) (cdb), (len));

#define ASC_DBG_PRT_SENSE(lvl, sense, len) \
        ASC_DBG_PRT_HEX((lvl), "SENSE", (uchar *) (sense), (len));

#define ASC_DBG_PRT_INQUIRY(lvl, inq, len) \
        ASC_DBG_PRT_HEX((lvl), "INQUIRY", (uchar *) (inq), (len));
#endif /* ADVANSYS_DEBUG */

#ifndef ADVANSYS_ASSERT
#define ASC_ASSERT(a)
#else /* ADVANSYS_ASSERT */

#define ASC_ASSERT(a) \
    { \
        if (!(a)) { \
            printk("ASC_ASSERT() Failure: file %s, line %d\n", \
                __FILE__, __LINE__); \
        } \
    }

#endif /* ADVANSYS_ASSERT */


/*
 * --- Driver Structures
 */

#ifdef ADVANSYS_STATS

/* Per board statistics structure */
struct asc_stats {
    /* Driver Entrypoint Statistics */
    ulong     command;         /* # calls to advansys_command() */
    ulong     queuecommand;    /* # calls to advansys_queuecommand() */
    ulong     abort;           /* # calls to advansys_abort() */
    ulong     reset;           /* # calls to advansys_reset() */
    ulong     biosparam;       /* # calls to advansys_biosparam() */
    ulong     check_interrupt; /* # advansys_interrupt() check pending calls */
    ulong     interrupt;       /* # advansys_interrupt() interrupts */
    ulong     callback;        /* # calls asc_isr_callback() */
    ulong     done;            /* # calls request scsi_done */
    /* AscExeScsiQueue() Statistics */
    ulong     asc_noerror;     /* # AscExeScsiQueue() ASC_NOERROR returns. */
    ulong     asc_busy;        /* # AscExeScsiQueue() ASC_BUSY returns. */
    ulong     asc_error;       /* # AscExeScsiQueue() ASC_ERROR returns. */
    ulong     asc_unknown;     /* # AscExeScsiQueue() unknown returns. */
    /* Data Transfer Statistics */
    ulong     cont_cnt;        /* # non-scatter-gather I/O requests received */
    ulong     cont_xfer;       /* # contiguous transfer 512-bytes */
    ulong     sg_cnt;          /* # scatter-gather I/O requests received */
    ulong     sg_elem;         /* # scatter-gather elements */
    ulong     sg_xfer;         /* # scatter-gather transfer 512-bytes */
};
#endif /* ADVANSYS_STATS */

/*
 * Request queuing structure
 */
typedef struct asc_queue {
    ASC_SCSI_BIT_ID_TYPE  q_tidmask;                /* queue mask */
    REQP                  q_first[ASC_MAX_TID+1];   /* first queued request */
    REQP                  q_last[ASC_MAX_TID+1];    /* last queued request */
#ifdef ADVANSYS_STATS
    short                 q_cur_cnt[ASC_MAX_TID+1]; /* current queue count */
    short                 q_max_cnt[ASC_MAX_TID+1]; /* maximum queue count */
    ulong                 q_tot_cnt[ASC_MAX_TID+1]; /* total enqueue count */
    ulong                 q_tot_tim[ASC_MAX_TID+1]; /* total time queued */
    ushort                q_max_tim[ASC_MAX_TID+1]; /* maximum time queued */
    ushort                q_min_tim[ASC_MAX_TID+1]; /* minimum time queued */
#endif /* ADVANSYS_STATS */
} asc_queue_t;

/*
 * Structure allocated for each board.
 *
 * This structure is allocated by scsi_register() at the end
 * of the 'Scsi_Host' structure starting at the 'hostdata'
 * field. It is guaranteed to be allocated from DMA-able memory.
 */
typedef struct asc_board {
    int                  id;                     /* Board Id */
    uint                 flags;                  /* Board flags */
    ASC_DVC_VAR          asc_dvc_var;            /* Board configuration */
    ASC_DVC_CFG          asc_dvc_cfg;            /* Device configuration */
    asc_queue_t          active;                 /* Active command queue */
    asc_queue_t          waiting;                /* Waiting command queue */
    asc_queue_t          done;                   /* Done command queue */
    ASC_SCSI_BIT_ID_TYPE init_tidmask;           /* Target initialized mask */
    /* The following three structures must be in DMA-able memory. */
    ASC_SCSI_REQ_Q       scsireqq;
    ASC_CAP_INFO         cap_info;
    ASC_SCSI_INQUIRY     inquiry;
    Scsi_Device          *device[ASC_MAX_TID+1]; /* Mid-Level Scsi Device */
    ushort               reqcnt[ASC_MAX_TID+1];  /* Starvation request count */
    uchar                sdtr_data[ASC_MAX_TID+1]; /* SDTR information */
#if ASC_QUEUE_FLOW_CONTROL
    ushort               nerrcnt[ASC_MAX_TID+1]; /* No error request count */
#endif /* ASC_QUEUE_FLOW_CONTROL */
    ASC_SCSI_BIT_ID_TYPE queue_full;             /* Queue full mask */
    ushort    queue_full_cnt[ASC_MAX_TID+1];     /* Queue full count */
    ASCEEP_CONFIG        eep_config;             /* EEPROM configuration */
    ulong                last_reset;             /* Saved last reset time */
#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,0)
    /* /proc/scsi/advansys/[0...] */
    char                 *prtbuf;                /* Statistics Print Buffer */
#endif /* version >= v1.3.0 */
#ifdef ADVANSYS_STATS
    struct asc_stats     asc_stats;              /* Board statistics */
#endif /* ADVANSYS_STATS */
} asc_board_t;

/*
 * PCI configuration structures
 */
typedef struct _PCI_DATA_
{
    uchar    type;
    uchar    bus;
    uchar    slot;
    uchar    func;
    uchar    offset;
} PCI_DATA;

typedef struct _PCI_DEVICE_
{
    ushort   vendorID;
    ushort   deviceID;
    ushort   slotNumber;
    ushort   slotFound;
    uchar    busNumber;
    uchar    maxBusNumber;
    uchar    devFunc;
    ushort   startSlot;
    ushort   endSlot;
    uchar    bridge;
    uchar    type;
} PCI_DEVICE;

typedef struct _PCI_CONFIG_SPACE_
{
    ushort   vendorID;
    ushort   deviceID;
    ushort   command;
    ushort   status;
    uchar    revision;
    uchar    classCode[3];
    uchar    cacheSize;
    uchar    latencyTimer;
    uchar    headerType;
    uchar    bist;
    ulong    baseAddress[6];
    ushort   reserved[4];
    ulong    optionRomAddr;
    ushort   reserved2[4];
    uchar    irqLine;
    uchar    irqPin;
    uchar    minGnt;
    uchar    maxLatency;
} PCI_CONFIG_SPACE;


/*
 * --- Driver Data
 */

/* Note: All driver global data should be initialized. */

#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,0)
struct proc_dir_entry proc_scsi_advansys =
{
    PROC_SCSI_ADVANSYS,                /* unsigned short low_ino */
    8,                                /* unsigned short namelen */
    "advansys",                        /* const char *name */
    S_IFDIR | S_IRUGO | S_IXUGO,    /* mode_t mode */
    2                                /* nlink_t nlink */
};
#endif /* version >= v1.3.0 */

/* Number of boards detected in system. */
STATIC int asc_board_count = 0;
STATIC struct Scsi_Host    *asc_host[ASC_NUM_BOARD_SUPPORTED] = { 0 };

/* Overrun buffer shared between all boards. */
STATIC uchar overrun_buf[ASC_OVERRUN_BSIZE] = { 0 };

/*
 * Global structures required to issue a command.
 */
STATIC ASC_SCSI_Q asc_scsi_q = { { 0 } };
STATIC ASC_SG_HEAD asc_sg_head = { 0 };

/* List of supported bus types. */
STATIC ushort asc_bus[ASC_NUM_BUS] ASC_INITDATA = {
    ASC_IS_ISA,
    ASC_IS_VL,
    ASC_IS_EISA,
    ASC_IS_PCI,
};

STATIC int pci_scan_method ASC_INITDATA = -1;

/*
 * Used with the LILO 'advansys' option to eliminate or
 * limit I/O port probing at boot time, cf. advansys_setup().
 */
STATIC int asc_iopflag = ASC_FALSE;
STATIC int asc_ioport[ASC_NUM_BOARD_SUPPORTED] = { 0, 0, 0, 0 };

#ifdef ADVANSYS_DEBUG
STATIC char *
asc_bus_name[ASC_NUM_BUS] = {
    "ASC_IS_ISA",
    "ASC_IS_VL",
    "ASC_IS_EISA",
    "ASC_IS_PCI",
};

STATIC int          asc_dbglvl = 0;
#endif /* ADVANSYS_DEBUG */

/* Declaration for Asc Library internal data referenced by driver. */
STATIC PortAddr     _asc_def_iop_base[];


/*
 * --- Driver Function Prototypes
 *
 * advansys.h contains function prototypes for functions global to Linux.
 */

#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,0)
STATIC int          asc_proc_copy(off_t, off_t, char *, int , char *, int);
#endif /* version >= v1.3.0 */
#if LINUX_VERSION_CODE < ASC_LINUX_VERSION(1,3,70)
STATIC void         advansys_interrupt(int, struct pt_regs *);
#else /* version >= v1.3.70 */
STATIC void         advansys_interrupt(int, void *, struct pt_regs *);
#endif /* version >= v1.3.70 */
#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,89)
STATIC void         advansys_select_queue_depths(struct Scsi_Host *,
                                                Scsi_Device *);
#endif /* version >= v1.3.89 */
STATIC void         advansys_command_done(Scsi_Cmnd *);
STATIC void         asc_scsi_done_list(Scsi_Cmnd *);
STATIC int          asc_execute_scsi_cmnd(Scsi_Cmnd *);
STATIC void         asc_isr_callback(ASC_DVC_VAR *, ASC_QDONE_INFO *);
STATIC int          asc_init_dev(ASC_DVC_VAR *, Scsi_Cmnd *);
STATIC int          asc_srch_pci_dev(PCI_DEVICE *);
STATIC uchar        asc_scan_method(void);
STATIC int          asc_pci_find_dev(PCI_DEVICE *);
STATIC void         asc_get_pci_cfg(PCI_DEVICE *, PCI_CONFIG_SPACE *);
STATIC ushort       asc_get_cfg_word(PCI_DATA *);
STATIC uchar        asc_get_cfg_byte(PCI_DATA *);
STATIC void         asc_put_cfg_byte(PCI_DATA *, uchar);
STATIC void         asc_enqueue(asc_queue_t *, REQP, int);
STATIC REQP         asc_dequeue(asc_queue_t *, int);
STATIC REQP         asc_dequeue_list(asc_queue_t *, REQP *, int);
STATIC int          asc_rmqueue(asc_queue_t *, REQP);
STATIC int          asc_isqueued(asc_queue_t *, REQP);
STATIC void         asc_execute_queue(asc_queue_t *);
#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,0)
STATIC int            asc_prt_board_devices(struct Scsi_Host *, char *, int);
STATIC int            asc_prt_board_eeprom(struct Scsi_Host *, char *, int);
STATIC int            asc_prt_driver_conf(struct Scsi_Host *, char *, int);
STATIC int            asc_prt_board_info(struct Scsi_Host *, char *, int);
STATIC int            asc_prt_line(char *, int, char *fmt, ...);
#endif /* version >= v1.3.0 */

/* Declaration for Asc Library internal functions reference by driver. */
STATIC int            AscFindSignature(PortAddr);
STATIC ushort         AscGetEEPConfig(PortAddr, ASCEEP_CONFIG *, ushort);

#ifdef ADVANSYS_STATS
STATIC int            asc_prt_board_stats(struct Scsi_Host *, char *, int);
#endif /* ADVANSYS_STATS */

#ifdef ADVANSYS_DEBUG
STATIC void         asc_prt_scsi_host(struct Scsi_Host *);
STATIC void         asc_prt_scsi_cmnd(Scsi_Cmnd *);
STATIC void         asc_prt_dvc_cfg(ASC_DVC_CFG *);
STATIC void         asc_prt_dvc_var(ASC_DVC_VAR *);
STATIC void         asc_prt_scsi_q(ASC_SCSI_Q *);
STATIC void         asc_prt_qdone_info(ASC_QDONE_INFO *);
STATIC void         asc_prt_hex(char *f, uchar *, int);
#endif /* ADVANSYS_DEBUG */

#ifdef ADVANSYS_ASSERT
STATIC int             interrupts_enabled(void);
#endif /* ADVANSYS_ASSERT */


/*
 * --- Linux 'Scsi_Host_Template' and advansys_setup() Functions
 */

#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,0)
/*
 * advansys_proc_info() - /proc/scsi/advansys/[0-(ASC_NUM_BOARD_SUPPORTED-1)]
 *
 * *buffer: I/O buffer
 * **start: if inout == FALSE pointer into buffer where user read should start
 * offset: current offset into a /proc/scsi/advansys/[0...] file
 * length: length of buffer
 * hostno: Scsi_Host host_no
 * inout: TRUE - user is writing; FALSE - user is reading
 *
 * Return the number of bytes read from or written to a
 * /proc/scsi/advansys/[0...] file.
 *
 * Note: This function uses the per board buffer 'prtbuf' which is
 * allocated when the board is initialized in advansys_detect(). The
 * buffer is ASC_PRTBUF_SIZE bytes. The function asc_proc_copy() is
 * used to write to the buffer. The way asc_proc_copy() is written
 * if 'prtbuf' is too small it will not be overwritten. Instead the
 * user just won't get all the available statistics.
 */
int
advansys_proc_info(char *buffer, char **start, off_t offset, int length, 
                   int hostno, int inout)
{
    struct Scsi_Host    *shp;
    asc_board_t         *boardp;
    int                 i;
    char                *cp;
    int                 cplen;
    int                 cnt;
    int                 totcnt;
    int                 leftlen;
    char                *curbuf;
    off_t               advoffset;
    Scsi_Device         *scd;

    ASC_DBG(1, "advansys_proc_info: begin\n");

    /*
     * User write not supported.
     */
    if (inout == TRUE) {
        return(-ENOSYS);
    }

    /*
     * User read of /proc/scsi/advansys/[0...] file.
     */

    /* Find the specified board. */
    for (i = 0; i < asc_board_count; i++) {
        if (asc_host[i]->host_no == hostno) {
            break;
        }
    }
    if (i == asc_board_count) {
        return(-ENOENT);
    }

    shp = asc_host[i];
    boardp = ASC_BOARDP(shp);

    /* Copy read data starting at the beginning of the buffer. */
    *start = buffer;
    curbuf = buffer;
    advoffset = 0;
    totcnt = 0;
    leftlen = length;

    /*
     * Get board configuration information.
     *
     * advansys_info() returns the board string from its own static buffer.
     */
    cp = (char *) advansys_info(shp);
    strcat(cp, "\n");
    cplen = strlen(cp);
    /* Copy board information. */
    cnt = asc_proc_copy(advoffset, offset, curbuf, leftlen, cp, cplen);
    totcnt += cnt;
    leftlen -= cnt;
    if (leftlen == 0) {
        ASC_DBG1(1, "advansys_proc_info: totcnt %d\n", totcnt);
        return totcnt;
    }
    advoffset += cplen;
    curbuf += cnt;

    /*
     * Display driver information for each device attached to the board.
     */
    cp = boardp->prtbuf;
    cplen = asc_prt_board_devices(shp, cp, ASC_PRTBUF_SIZE);
    ASC_ASSERT(cplen < ASC_PRTBUF_SIZE);
    cnt = asc_proc_copy(advoffset, offset, curbuf, leftlen, cp, cplen);
    totcnt += cnt;
    leftlen -= cnt;
    if (leftlen == 0) {
        ASC_DBG1(1, "advansys_proc_info: totcnt %d\n", totcnt);
        return totcnt;
    }
    advoffset += cplen;
    curbuf += cnt;

    /*
     * Display target driver information for each device attached
     * to the board.
     */
    for (scd = scsi_devices; scd; scd = scd->next) {
        if (scd->host == shp) {
            cp = boardp->prtbuf;
            /*
             * Note: If proc_print_scsidevice() writes more than
             * ASC_PRTBUF_SIZE bytes, it will overrun 'prtbuf'.
             */
            proc_print_scsidevice(scd, cp, &cplen, 0);
            ASC_ASSERT(cplen < ASC_PRTBUF_SIZE);
            cnt = asc_proc_copy(advoffset, offset, curbuf, leftlen, cp, cplen);
            totcnt += cnt;
            leftlen -= cnt;
            if (leftlen == 0) {
                ASC_DBG1(1, "advansys_proc_info: totcnt %d\n", totcnt);
                return totcnt;
            }
            advoffset += cplen;
            curbuf += cnt;
        }
    }
    
    /*
     * Display EEPROM configuration for the board.
     */
    cp = boardp->prtbuf;
    cplen = asc_prt_board_eeprom(shp, cp, ASC_PRTBUF_SIZE);
    ASC_ASSERT(cplen < ASC_PRTBUF_SIZE);
    cnt = asc_proc_copy(advoffset, offset, curbuf, leftlen, cp, cplen);
    totcnt += cnt;
    leftlen -= cnt;
    if (leftlen == 0) {
        ASC_DBG1(1, "advansys_proc_info: totcnt %d\n", totcnt);
        return totcnt;
    }
    advoffset += cplen;
    curbuf += cnt;

    /*
     * Display driver configuration and information for the board.
     */
    cp = boardp->prtbuf;
    cplen = asc_prt_driver_conf(shp, cp, ASC_PRTBUF_SIZE);
    ASC_ASSERT(cplen < ASC_PRTBUF_SIZE);
    cnt = asc_proc_copy(advoffset, offset, curbuf, leftlen, cp, cplen);
    totcnt += cnt;
    leftlen -= cnt;
    if (leftlen == 0) {
        ASC_DBG1(1, "advansys_proc_info: totcnt %d\n", totcnt);
        return totcnt;
    }
    advoffset += cplen;
    curbuf += cnt;

#ifdef ADVANSYS_STATS
    /*
     * Display driver statistics for the board.
     */
    cp = boardp->prtbuf;
    cplen = asc_prt_board_stats(shp, cp, ASC_PRTBUF_SIZE);
    ASC_ASSERT(cplen < ASC_PRTBUF_SIZE);
    cnt = asc_proc_copy(advoffset, offset, curbuf, leftlen, cp, cplen);
    totcnt += cnt;
    leftlen -= cnt;
    if (leftlen == 0) {
        ASC_DBG1(1, "advansys_proc_info: totcnt %d\n", totcnt);
        return totcnt;
    }
    advoffset += cplen;
    curbuf += cnt;
#endif /* ADVANSYS_STATS */

    /*
     * Display Asc Library dynamic configuration information
     * for the board.
     */
    cp = boardp->prtbuf;
    cplen = asc_prt_board_info(shp, cp, ASC_PRTBUF_SIZE);
    ASC_ASSERT(cplen < ASC_PRTBUF_SIZE);
    cnt = asc_proc_copy(advoffset, offset, curbuf, leftlen, cp, cplen);
    totcnt += cnt;
    leftlen -= cnt;
    if (leftlen == 0) {
        ASC_DBG1(1, "advansys_proc_info: totcnt %d\n", totcnt);
        return totcnt;
    }
    advoffset += cplen;
    curbuf += cnt;

    ASC_DBG1(1, "advansys_proc_info: totcnt %d\n", totcnt);

    return totcnt;
}
#endif /* version >= v1.3.0 */


/*
 * advansys_detect()
 *
 * Detect function for AdvanSys adapters.
 *
 * Argument is a pointer to the host driver's scsi_hosts entry.
 *
 * Return number of adapters found.
 *
 * Note: Because this function is called during system initialization
 * it must not call SCSI mid-level functions including scsi_malloc()
 * and scsi_free().
 */
ASC_INITFUNC(
int
advansys_detect(Scsi_Host_Template *tpnt)
)
{
    static int          detect_called = ASC_FALSE;
    int                 iop;
    int                 bus;
    struct Scsi_Host    *shp;
    asc_board_t         *boardp;
    ASC_DVC_VAR         *asc_dvc_varp;
    int                 ioport = 0;
    int                 share_irq = FALSE;
    PCI_DEVICE          pciDevice;
    PCI_CONFIG_SPACE    pciConfig;
    int                 ret;

    if (detect_called == ASC_FALSE) {
        detect_called = ASC_TRUE;
    } else {
        printk("AdvanSys SCSI: advansys_detect() mulitple calls ignored\n");
        return 0;
    }

    ASC_DBG(1, "advansys_detect: begin\n");

#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,0)
    tpnt->proc_dir = &proc_scsi_advansys;
#endif /* version >= v1.3.0 */

    asc_board_count = 0;

    /*
     * If I/O port probing has been modified, then verify and
     * clean-up the 'asc_ioport' list.
     */
    if (asc_iopflag == ASC_TRUE) {
        for (ioport = 0; ioport < ASC_NUM_BOARD_SUPPORTED; ioport++) {
            ASC_DBG2(1, "advansys_detect: asc_ioport[%d] %x\n",
                ioport, asc_ioport[ioport]);
            if (asc_ioport[ioport] != 0) {
                for (iop = 0; iop < ASC_IOADR_TABLE_MAX_IX; iop++) {
                    if (_asc_def_iop_base[iop] == asc_ioport[ioport]) {
                        break;
                    }
                }
                if (iop == ASC_IOADR_TABLE_MAX_IX) {
                    printk("AdvanSys SCSI: specified I/O Port 0x%X is invalid\n",
                        asc_ioport[ioport]);
                    asc_ioport[ioport] = 0;
                }
            }
        }
        ioport = 0;
    }

    memset(&pciDevice, 0, sizeof(PCI_DEVICE));
    memset(&pciConfig, 0, sizeof(PCI_CONFIG_SPACE));
    pciDevice.maxBusNumber = PCI_MAX_BUS;
    pciDevice.endSlot = PCI_MAX_SLOT;

    for (bus = 0; bus < ASC_NUM_BUS; bus++) {

        ASC_DBG2(1, "advansys_detect: bus search type %d (%s)\n",
            bus, asc_bus_name[bus]);
        iop = 0;

        while (asc_board_count < ASC_NUM_BOARD_SUPPORTED) {

            ASC_DBG1(2, "advansys_detect: asc_board_count %d\n",
                asc_board_count);

            switch (asc_bus[bus]) {
            case ASC_IS_ISA:
            case ASC_IS_VL:
                if (asc_iopflag == ASC_FALSE) {
                    iop = AscSearchIOPortAddr(iop, asc_bus[bus]);
                } else {
                    /*
                     * ISA and VL I/O port scanning has either been
                     * eliminated or limited to selected ports on
                     * the LILO command line, /etc/lilo.conf, or
                     * by setting variables when the module was loaded.
                     */
                    ASC_DBG(1, "advansys_detect: I/O port scanning modified\n");
                ioport_try_again:
                    iop = 0;
                    for (; ioport < ASC_NUM_BOARD_SUPPORTED; ioport++) {
                        if ((iop = asc_ioport[ioport]) != 0) {
                            break;
                        }
                    }
                    if (iop) {
                        ASC_DBG1(1, "advansys_detect: probing I/O port %x...\n",
                            iop);
                        if (check_region(iop, ASC_IOADR_GAP) != 0) {
                            printk("AdvanSys SCSI: specified I/O Port 0x%X is busy\n", iop);
                            /* Don't try this I/O port twice. */
                            asc_ioport[ioport] = 0;
                            goto ioport_try_again;
                        } else if (AscFindSignature(iop) == ASC_FALSE) {
                            printk("AdvanSys SCSI: specified I/O Port 0x%X has no adapter\n", iop);
                            /* Don't try this I/O port twice. */
                            asc_ioport[ioport] = 0;
                            goto ioport_try_again;
                        } else {
                            /*
                             * If this isn't an ISA board, then it must be
                             * a VL board. If currently looking an ISA
                             * board is being looked for then try for
                             * another ISA board in 'asc_ioport'.
                             */
                            if (asc_bus[bus] == ASC_IS_ISA &&
                                (AscGetChipVersion(iop, ASC_IS_ISA) &
                                 ASC_CHIP_VER_ISA_BIT) == 0) {
                                 /*
                                 * Don't clear 'asc_ioport[ioport]'. Try
                                 * this board again for VL. Increment
                                 * 'ioport' past this board.
                                 */
                                 ioport++;
                                 goto ioport_try_again;
                            }
                        }
                        /*
                         * This board appears good, don't try the I/O port
                         * again by clearing its value. Increment 'ioport'
                         * for the next iteration.
                         */
                        asc_ioport[ioport++] = 0;
                    }
                }
                break;

            case ASC_IS_EISA:
                iop = AscSearchIOPortAddr(iop, asc_bus[bus]);
                break;

            case ASC_IS_PCI:
                    if (asc_srch_pci_dev(&pciDevice) != PCI_DEVICE_FOUND) {
                        iop = 0;
                    } else {
                        ASC_DBG2(2,
                            "advansys_detect: slotFound %d, busNumber %d\n",
                            pciDevice.slotFound, pciDevice.busNumber);
                        asc_get_pci_cfg(&pciDevice, &pciConfig);
                        iop = pciConfig.baseAddress[0] & PCI_IOADDRESS_MASK;
                        ASC_DBG2(2, "advansys_detect: iop %x, irqLine %d\n",
                            iop, pciConfig.irqLine);
                    }
                break;

            default:
                ASC_PRINT1("advansys_detect: unknown bus type: %d\n",
                    asc_bus[bus]);
                break;
            }
            ASC_DBG1(1, "advansys_detect: iop %x\n", iop);

            /*
             * Adapter not found, try next bus type.
             */
            if (iop == 0) {
                break;
            }

            /*
             * Adapter found.
             *
             * Register the adapter, get its configuration, and
             * initialize it.
             */
            ASC_DBG(2, "advansys_detect: scsi_register()\n");
            shp = scsi_register(tpnt, sizeof(asc_board_t));

            /* Save a pointer to the Scsi_host of each board found. */
            asc_host[asc_board_count++] = shp;

            /* Initialize private per board data */
            boardp = ASC_BOARDP(shp);
            memset(boardp, 0, sizeof(asc_board_t));
            boardp->id = asc_board_count - 1;
            asc_dvc_varp = &boardp->asc_dvc_var;
            asc_dvc_varp->drv_ptr = (ulong) boardp;
            asc_dvc_varp->cfg = &boardp->asc_dvc_cfg;
            asc_dvc_varp->cfg->overrun_buf = &overrun_buf[0];
            asc_dvc_varp->iop_base = iop;

#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,0)
            if ((boardp->prtbuf =
                kmalloc(ASC_PRTBUF_SIZE, GFP_ATOMIC)) == NULL) {
                ASC_PRINT3(
"advansys_detect: board %d: kmalloc(%d, %d) returned NULL\n",
                    boardp->id, ASC_PRTBUF_SIZE, GFP_ATOMIC);
                scsi_unregister(shp);
                asc_board_count--;
                continue;
            }
#endif /* version >= v1.3.0 */

            /*
             * Set the board bus type and PCI IRQ for AscInitGetConfig().
             */
            asc_dvc_varp->bus_type = asc_bus[bus];
            switch (asc_dvc_varp->bus_type) {
            case ASC_IS_ISA:
                shp->unchecked_isa_dma = TRUE;
                share_irq = FALSE;
                break;
            case ASC_IS_VL:
                shp->unchecked_isa_dma = FALSE;
                share_irq = FALSE;
                break;
            case ASC_IS_EISA:
                shp->unchecked_isa_dma = FALSE;
                share_irq = TRUE;
                break;
            case ASC_IS_PCI:
                shp->irq = asc_dvc_varp->irq_no = pciConfig.irqLine;
                asc_dvc_varp->cfg->pci_device_id = pciConfig.deviceID;
                asc_dvc_varp->cfg->pci_slot_info =
                        ASC_PCI_MKID(pciDevice.busNumber,
                                     pciDevice.slotFound,
                                     pciDevice.devFunc);
                shp->unchecked_isa_dma = FALSE;
                share_irq = TRUE;
                break;
            default:
                ASC_PRINT2(
"advansys_detect: board %d: unknown adapter type: %d",
                    boardp->id, asc_dvc_varp->bus_type);
                shp->unchecked_isa_dma = TRUE;
                share_irq = FALSE;
                break;
            }

            /*
             * Get the board configuration.
             *
             * NOTE: AscInitGetConfig() may change the board's bus_type
             * value. The asc_bus[bus] value should no longer be used. If
             * the bus_type field must be referenced only use the bit-wise
             * AND operator "&".
             */
            ASC_DBG(2, "advansys_detect: AscInitGetConfig()\n");
            switch(ret = AscInitGetConfig(asc_dvc_varp)) {
            case 0:    /* No error */
                break;
            case ASC_WARN_IO_PORT_ROTATE:
                ASC_PRINT1(
"AscInitGetConfig: board %d: I/O port address modified\n",
                    boardp->id);
                break;
            case ASC_WARN_AUTO_CONFIG:
                ASC_PRINT1(
"AscInitGetConfig: board %d: I/O port increment switch enabled\n",
                    boardp->id);
                break;
            case ASC_WARN_EEPROM_CHKSUM:
                ASC_PRINT1(
"AscInitGetConfig: board %d: EEPROM checksum error\n",
                    boardp->id);
                break;
            case ASC_WARN_IRQ_MODIFIED:
                ASC_PRINT1(
"AscInitGetConfig: board %d: IRQ modified\n",
                    boardp->id);
                break;
            case ASC_WARN_CMD_QNG_CONFLICT:
                ASC_PRINT1(
"AscInitGetConfig: board %d: tag queuing enabled w/o disconnects\n",
                    boardp->id);
                break;
            default:
                ASC_PRINT2(
"AscInitGetConfig: board %d: unknown warning: %x\n",
                    boardp->id, ret);
                break;
            }
            if (asc_dvc_varp->err_code != 0) {
                ASC_PRINT3(
"AscInitGetConfig: board %d error: init_state %x, err_code %x\n",
                    boardp->id, asc_dvc_varp->init_state,
                    asc_dvc_varp->err_code);
#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,0)
                kfree(boardp->prtbuf);
#endif /* version >= v1.3.0 */
                scsi_unregister(shp);
                asc_board_count--;
                continue;
            }

            /*
             * Set the adapter's target id bit in the init_tidmask field.
             */
            boardp->init_tidmask |=
                ASC_TIX_TO_TARGET_ID(asc_dvc_varp->cfg->chip_scsi_id);

            /*
             * Save EEPROM settings for the board.
             */
            boardp->eep_config.init_sdtr = asc_dvc_varp->init_sdtr;
            boardp->eep_config.disc_enable = asc_dvc_varp->cfg->disc_enable;
            boardp->eep_config.use_cmd_qng = asc_dvc_varp->cfg->cmd_qng_enabled;
            boardp->eep_config.isa_dma_speed = asc_dvc_varp->cfg->isa_dma_speed;
            boardp->eep_config.start_motor = asc_dvc_varp->start_motor;
            boardp->eep_config.cntl = asc_dvc_varp->dvc_cntl;
            boardp->eep_config.no_scam = asc_dvc_varp->no_scam;
            boardp->eep_config.max_total_qng = asc_dvc_varp->max_total_qng;
            boardp->eep_config.chip_scsi_id = asc_dvc_varp->cfg->chip_scsi_id;
            /* 'max_tag_qng' is set to the same value for every device. */
            boardp->eep_config.max_tag_qng = asc_dvc_varp->cfg->max_tag_qng[0];

            /*
             * Modify board configuration.
             */
            asc_dvc_varp->isr_callback = (Ptr2Func) asc_isr_callback;
            asc_dvc_varp->exe_callback = (Ptr2Func) NULL;

            ASC_DBG(2, "advansys_detect: AscInitSetConfig()\n");
            switch (ret = AscInitSetConfig(asc_dvc_varp)) {
            case 0:    /* No error. */
                break;
            case ASC_WARN_IO_PORT_ROTATE:
                ASC_PRINT1(
"AscInitSetConfig: board %d: I/O port address modified\n",
                    boardp->id);
                break;
            case ASC_WARN_AUTO_CONFIG:
                ASC_PRINT1(
"AscInitSetConfig: board %d: I/O port increment switch enabled\n",
                    boardp->id);
                break;
            case ASC_WARN_EEPROM_CHKSUM:
                ASC_PRINT1(
"AscInitSetConfig: board %d: EEPROM checksum error\n",
                    boardp->id);
                break;
            case ASC_WARN_IRQ_MODIFIED:
                ASC_PRINT1(
"AscInitSetConfig: board %d: IRQ modified\n",
                    boardp->id);
                break;
            case ASC_WARN_CMD_QNG_CONFLICT:
                ASC_PRINT1(
"AscInitSetConfig: board %d: tag queuing w/o disconnects\n",
                    boardp->id);
                break;
            default:
                ASC_PRINT2(
"AscInitSetConfig: board %d: unknown warning: %x\n",
                    boardp->id, ret);
                break;
            }
            if (asc_dvc_varp->err_code != 0) {
                ASC_PRINT3(
"AscInitSetConfig: board %d error: init_state %x, err_code %x\n",
                    boardp->id, asc_dvc_varp->init_state,
                    asc_dvc_varp->err_code);
#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,0)
                kfree(boardp->prtbuf);
#endif /* version >= v1.3.0 */
                scsi_unregister(shp);
                asc_board_count--;
                continue;
            }

            /*
             * Finish initializing the 'Scsi_Host' structure.
             */

            /* AscInitSetConfig() will set the IRQ for non-PCI boards. */
            if ((asc_dvc_varp->bus_type & ASC_IS_PCI) == 0) {
                shp->irq = asc_dvc_varp->irq_no;
            }

            /*
             * One host supports one channel. There are two different
             * hosts for each channel of a dual channel board.
             */
#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,89)
            shp->max_channel = 0;
#endif /* version >= v1.3.89 */
            shp->max_id = ASC_MAX_TID + 1;
            shp->max_lun = ASC_MAX_LUN + 1;

            shp->io_port = asc_dvc_varp->iop_base;
            shp->n_io_port = ASC_IOADR_GAP;
            shp->this_id = asc_dvc_varp->cfg->chip_scsi_id;

            /* Maximum number of queues this adapter can handle. */
            shp->can_queue = asc_dvc_varp->max_total_qng;

#if LINUX_VERSION_CODE < ASC_LINUX_VERSION(1,3,89)
            /*
             * Set a conservative 'cmd_per_lun' value to prevent memory
             * allocation failures.
             */
#ifdef MODULE
            shp->cmd_per_lun = 1;
#else /* MODULE */
            shp->cmd_per_lun = 4;
#endif /* MODULE */
            ASC_DBG1(1, "advansys_detect: cmd_per_lun: %d\n", shp->cmd_per_lun);
#else /* version >= v1.3.89 */
            /*
             * Use the host 'select_queue_depths' function to determine
             * the number of commands to queue per device.
             */
            shp->select_queue_depths = advansys_select_queue_depths;

#ifdef MODULE
            /*
             * Following v1.3.89, 'cmd_per_lun' is no longer needed
             * and should be set to zero. But because of a bug introduced
             * in v1.3.89 if the driver is compiled as a module and
             * 'cmd_per_lun' is zero, the Mid-Level SCSI function
             * 'allocate_device' will panic. To allow the driver to
             * work as a module in these kernels set 'cmd_per_lun' to 1.
             */
            shp->cmd_per_lun = 1;
#else /* MODULE */
            shp->cmd_per_lun = 0;
#endif /* MODULE */
#endif /* version >= v1.3.89 */

            /*
             * Set the maximum number of scatter-gather elements adapter
             * can handle.
             */

#ifdef MODULE
            /*
             * If the driver is compiled as a module, set a conservative
             * 'sg_tablesize' value to prevent memory allocation failures.
             * Memory allocation errors are more likely to occur at module
             * load time, then at driver initialization time.
             */
            shp->sg_tablesize = 8;
#else /* MODULE */
            /*
             * Allow two commands with 'sg_tablesize' scatter-gather
             * elements to be executed simultaneously. This value is
             * the theoretical hardware limit. It may be decreased
             * below.
             */
            shp->sg_tablesize =
                (((asc_dvc_varp->max_total_qng - 2) / 2) *
                ASC_SG_LIST_PER_Q) + 1;
#endif /* MODULE */

            /*
             * The value of 'sg_tablesize' can not exceed the SCSI
             * mid-level driver definition of SG_ALL. SG_ALL also
             * must not be exceeded, because it is used to define the
             * size of the scatter-gather table in 'struct asc_sg_head'.
             */
            if (shp->sg_tablesize > SG_ALL) {
                shp->sg_tablesize = SG_ALL;
            }

            ASC_DBG1(1, "advansys_detect: sg_tablesize: %d\n",
                shp->sg_tablesize);

            /* BIOS start address. */
            shp->base = (char *) ((ulong) AscGetChipBiosAddress(
                                                asc_dvc_varp->iop_base,
                                                asc_dvc_varp->bus_type));

            /*
             * Register Board Resources - I/O Port, DMA, IRQ
             */

            /* Register I/O port range */
            ASC_DBG(2, "advansys_detect: request_region()\n");
            request_region(shp->io_port, shp->n_io_port, "advansys");

            /* Register DMA channel for ISA bus. */
            if ((asc_dvc_varp->bus_type & ASC_IS_ISA) == 0) {
                shp->dma_channel = NO_ISA_DMA;
            } else {
                shp->dma_channel = asc_dvc_varp->cfg->isa_dma_channel;
                if ((ret = request_dma(shp->dma_channel, "advansys")) != 0) {
                    ASC_PRINT3(
"advansys_detect: board %d: request_dma() %d failed %d\n",
                        boardp->id, shp->dma_channel, ret);
                    release_region(shp->io_port, shp->n_io_port);
#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,0)
                    kfree(boardp->prtbuf);
#endif /* version >= v1.3.0 */
                    scsi_unregister(shp);
                    asc_board_count--;
                    continue;
                }
                AscEnableIsaDma(shp->dma_channel);
            }

            /* Register IRQ Number. */
            ASC_DBG1(2, "advansys_detect: request_irq() %d\n", shp->irq);
#if LINUX_VERSION_CODE < ASC_LINUX_VERSION(1,3,70)
            if ((ret = request_irq(shp->irq, advansys_interrupt,
                            SA_INTERRUPT, "advansys")) != 0) {
#else /* version >= v1.3.70 */
            if ((ret = request_irq(shp->irq, advansys_interrupt,
                            SA_INTERRUPT | (share_irq == TRUE ? SA_SHIRQ : 0),
                            "advansys", boardp)) != 0) {
#endif /* version >= v1.3.70 */
                ASC_PRINT2(
"advansys_detect: board %d: request_irq() failed %d\n",
                    boardp->id, ret);
                release_region(shp->io_port, shp->n_io_port);
                if (shp->dma_channel != NO_ISA_DMA) {
                    free_dma(shp->dma_channel);
                }
#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,0)
                kfree(boardp->prtbuf);
#endif /* version >= v1.3.0 */
                scsi_unregister(shp);
                asc_board_count--;
                continue;
            }

            /*
             * Initialize board RISC chip and enable interrupts.
             */
            ASC_DBG(2, "advansys_detect: AscInitAsc1000Driver()\n");
            if (AscInitAsc1000Driver(asc_dvc_varp)) {
                ASC_PRINT3(
"AscInitAsc1000Driver: board %d: error: init_state %x, err_code %x\n",
                    boardp->id, asc_dvc_varp->init_state,
                    asc_dvc_varp->err_code);
                release_region(shp->io_port, shp->n_io_port);
                if (shp->dma_channel != NO_ISA_DMA) {
                    free_dma(shp->dma_channel);
                }
#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,0)
                kfree(boardp->prtbuf);
#endif /* version >= v1.3.0 */
#if LINUX_VERSION_CODE < ASC_LINUX_VERSION(1,3,70)
                free_irq(shp->irq);
#else /* version >= v1.3.70 */
                free_irq(shp->irq, boardp);
#endif /* version >= v1.3.70 */
                scsi_unregister(shp);
                asc_board_count--;
                continue;
            }
            ASC_DBG_PRT_SCSI_HOST(2, shp);
        }
    }
    ASC_DBG1(1, "advansys_detect: done: asc_board_count %d\n", asc_board_count);
    return asc_board_count;
}

/*
 * advansys_release()
 *
 * Release resources allocated for a single AdvanSys adapter.
 */
int
advansys_release(struct Scsi_Host *shp)
{
    asc_board_t    *boardp;

    ASC_DBG(1, "advansys_release: begin\n");
    boardp = ASC_BOARDP(shp);
#if LINUX_VERSION_CODE < ASC_LINUX_VERSION(1,3,70)
    free_irq(shp->irq);
#else /* version >= v1.3.70 */
    free_irq(shp->irq, boardp);
#endif /* version >= v1.3.70 */
    if (shp->dma_channel != NO_ISA_DMA) {
        ASC_DBG(1, "advansys_release: free_dma()\n");
        free_dma(shp->dma_channel);
    }
    release_region(shp->io_port, shp->n_io_port);
#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,0)
    ASC_ASSERT(boardp->prtbuf != NULL);
    kfree(boardp->prtbuf);
#endif /* version >= v1.3.0 */
    scsi_unregister(shp);
    ASC_DBG(1, "advansys_release: end\n");
    return 0;
}

/*
 * advansys_info()
 *
 * Return suitable for printing on the console with the argument
 * adapter's configuration information.
 *
 * Note: The information line should not exceed ASC_INFO_SIZE bytes,
 * otherwise the static 'info' array will be overrun.
 */
const char *
advansys_info(struct Scsi_Host *shp)
{
    static char     info[ASC_INFO_SIZE];
    asc_board_t     *boardp;
    ASC_DVC_VAR     *asc_dvc_varp;
    char            *busname;

    boardp = ASC_BOARDP(shp);
    asc_dvc_varp = &boardp->asc_dvc_var;
    ASC_DBG(1, "advansys_info: begin\n");
    if (asc_dvc_varp->bus_type & ASC_IS_ISA) {
        if ((asc_dvc_varp->bus_type & ASC_IS_ISAPNP) == ASC_IS_ISAPNP) {
            busname = "ISA PnP";
        } else {
            busname = "ISA";
        }
        sprintf(info,
            "AdvanSys SCSI %s: %s %u CDB: BIOS %X, IO %X-%X, IRQ %u, DMA %u",
            ASC_VERSION, busname, boardp->asc_dvc_var.max_total_qng,
            (unsigned) shp->base, shp->io_port,
            shp->io_port + (shp->n_io_port - 1), shp->irq, shp->dma_channel);
    } else if (asc_dvc_varp->bus_type & ASC_IS_PCI) {
        if ((asc_dvc_varp->bus_type & ASC_IS_PCI_ULTRA)
            == ASC_IS_PCI_ULTRA) {
            busname = "PCI Ultra";
        } else {
            busname = "PCI";
        }
        sprintf(info,
            "AdvanSys SCSI %s: %s %u CDB: IO %X-%X, IRQ %u",
            ASC_VERSION, busname, boardp->asc_dvc_var.max_total_qng,
            shp->io_port, shp->io_port + (shp->n_io_port - 1), shp->irq);
    } else {
        if (asc_dvc_varp->bus_type & ASC_IS_VL) {
            busname = "VL";
        } else if (asc_dvc_varp->bus_type & ASC_IS_EISA) {
            busname = "EISA";
        } else {
            busname = "?";
            ASC_PRINT2(
"advansys_info: board %d: unknown bus type %d\n",
                boardp->id, asc_dvc_varp->bus_type);
        }
        sprintf(info,
            "AdvanSys SCSI %s: %s %u CDB: BIOS %X, IO %X-%X, IRQ %u",
            ASC_VERSION, busname, boardp->asc_dvc_var.max_total_qng,
            (unsigned) shp->base, shp->io_port,
            shp->io_port + (shp->n_io_port - 1), shp->irq);
    }
    ASC_ASSERT(strlen(info) < ASC_INFO_SIZE);
    ASC_DBG(1, "advansys_info: end\n");
    return info;
}

/*
 * advansys_command()
 *
 * Polled-I/O. Apparently host drivers shouldn't return until
 * command is finished.
 *
 * Note: This is an old interface that is no longer used by the SCSI
 * mid-level driver. The new interface, advansys_queuecommand(),
 * currently handles all requests.
 */
int
advansys_command(Scsi_Cmnd *scp)
{
    ASC_DBG1(1, "advansys_command: scp %x\n", (unsigned) scp);
    ASC_STATS(scp->host, command);
    scp->SCp.Status = 0; /* Set to a known state */
    advansys_queuecommand(scp, advansys_command_done);
    /*
     * XXX - Can host drivers block here instead of spinning on
     * command status?
     */
    while (scp->SCp.Status == 0) {
        continue;
    }
    ASC_DBG1(1, "advansys_command: result %x\n", scp->result);
    return scp->result;
}

/*
 * advansys_queuecommand()
 *
 * This function always returns 0. Command return status is saved
 * in the 'scp' result field.
 */
int
advansys_queuecommand(Scsi_Cmnd *scp, void (*done)(Scsi_Cmnd *))
{
    struct Scsi_Host    *shp;
    asc_board_t         *boardp;
    int                 flags;
    Scsi_Cmnd           *done_scp;

    shp = scp->host;
    boardp = ASC_BOARDP(shp);
    ASC_STATS(shp, queuecommand);

    /*
     * Disable interrupts to preserve request ordering and provide
     * mutually exclusive access to global structures used to initiate
     * a request.
     */
    save_flags(flags);
    cli();

    /*
     * Block new commands while handling a reset or abort request.
     */
    if (boardp->flags & (ASC_HOST_IN_RESET | ASC_HOST_IN_ABORT)) {
        if (boardp->flags & ASC_HOST_IN_RESET) {
            ASC_DBG1(1,
                "advansys_queuecommand: scp %x blocked for reset request\n",
                (unsigned) scp);
            scp->result = HOST_BYTE(DID_RESET);
        } else {
            ASC_DBG1(1,
                "advansys_queuecommand: scp %x blocked for abort request\n",
                (unsigned) scp);
            scp->result = HOST_BYTE(DID_ABORT);
        }

        /*
         * Add blocked requests to the board's 'done' queue. The queued
         * requests will be completed at the end of the abort or reset
         * handling.
         */
        asc_enqueue(&boardp->done, scp, ASC_BACK);
        restore_flags(flags);
        return 0;
    }

    /*
     * Attempt to execute any waiting commands for the board.
     */
    if (!ASC_QUEUE_EMPTY(&boardp->waiting)) {
        ASC_DBG(1,
            "advansys_queuecommand: before asc_execute_queue() waiting\n");
        asc_execute_queue(&boardp->waiting);
    }

    /*
     * Save the function pointer to Linux mid-level 'done' function
     * and attempt to execute the command.
     *
     * If ASC_ERROR is returned the request has been added to the
     * board's 'active' queue and will be completed by the interrupt
     * handler.
     *
     * If ASC_BUSY is returned add the request to the board's per
     * target waiting list.
     * 
     * If an error occurred, the request will have been placed on the
     * board's 'done' queue and must be completed before returning.
     */
    scp->scsi_done = done;
    switch (asc_execute_scsi_cmnd(scp)) {
    case ASC_NOERROR:
        break;
    case ASC_BUSY:
        asc_enqueue(&boardp->waiting, scp, ASC_BACK);
        break;
    case ASC_ERROR:
    default:
        done_scp = asc_dequeue_list(&boardp->done, NULL, ASC_TID_ALL);
        /* Interrupts could be enabled here. */
        asc_scsi_done_list(done_scp);
        break;
    }

    restore_flags(flags);
    return 0;
}

/*
 * advansys_abort()
 *
 * Abort the command specified by 'scp'.
 */
int
advansys_abort(Scsi_Cmnd *scp)
{
    struct Scsi_Host    *shp;
    asc_board_t         *boardp;
    ASC_DVC_VAR         *asc_dvc_varp;
    int                 flags;
    int                 do_scsi_done;
    int                 scp_found;
    Scsi_Cmnd           *done_scp = NULL;
    int                 ret;

    /* Save current flags and disable interrupts. */
    save_flags(flags);
    cli();

    ASC_DBG1(1, "advansys_abort: scp %x\n", (unsigned) scp);

#ifdef ADVANSYS_STATS
    if (scp->host != NULL) {
        ASC_STATS(scp->host, abort);
    }    
#endif /* ADVANSYS_STATS */

#ifdef ADVANSYS_ASSERT
    do_scsi_done = ASC_ERROR;
    scp_found = ASC_ERROR;
    ret = ASC_ERROR;
#endif /* ADVANSYS_ASSERT */

#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,89)
    if (scp->serial_number != scp->serial_number_at_timeout) {
        ASC_PRINT1(
"advansys_abort: timeout serial number changed for request %x\n",
            (unsigned) scp);
        do_scsi_done = ASC_FALSE;
        scp_found = ASC_FALSE;
        ret = SCSI_ABORT_NOT_RUNNING;
    } else
#endif /* version >= v1.3.89 */
    if ((shp = scp->host) == NULL) {
        scp->result = HOST_BYTE(DID_ERROR);
        do_scsi_done = ASC_TRUE;
        scp_found = ASC_FALSE;
        ret = SCSI_ABORT_ERROR;
    } else if ((boardp = ASC_BOARDP(shp))->flags & 
                (ASC_HOST_IN_RESET | ASC_HOST_IN_ABORT)) {
        ASC_PRINT2(
"advansys_abort: board %d: Nested host reset or abort, flags 0x%x\n",
            boardp->id, boardp->flags);
        do_scsi_done = ASC_TRUE;
        if ((asc_rmqueue(&boardp->active, scp) == ASC_TRUE) ||
            (asc_rmqueue(&boardp->waiting, scp) == ASC_TRUE)) {
            scp_found = ASC_TRUE;
        } else {
            scp_found = ASC_FALSE;
        }
        scp->result = HOST_BYTE(DID_ERROR);
        ret = SCSI_ABORT_ERROR;
    } else {
        /* Set abort flag to avoid nested reset or abort requests. */
        boardp->flags |= ASC_HOST_IN_ABORT;

        do_scsi_done = ASC_TRUE;
        if (asc_rmqueue(&boardp->waiting, scp) == ASC_TRUE) {
            /*
              * If asc_rmqueue() found the command on the waiting
             * queue, it had not been sent to the device. After
             * the queue is removed, no other handling is required.
              */
            ASC_DBG1(1, "advansys_abort: scp %x found on waiting queue\n",
                (unsigned) scp);
            scp_found = ASC_TRUE;
            scp->result = HOST_BYTE(DID_ABORT);
            ret = SCSI_ABORT_SUCCESS;
        } else if (asc_isqueued(&boardp->active, scp) == ASC_TRUE) {
            /*
              * If asc_isqueued() found the command on the active
             * queue, it has been sent to the device. The command
             * should be returned through the interrupt handler after
             * calling AscAbortSRB().
              */
            asc_dvc_varp = &boardp->asc_dvc_var;
            scp->result = HOST_BYTE(DID_ABORT);

            sti(); /* Enable interrupts for AscAbortSRB(). */
            ASC_DBG1(1, "advansys_abort: before AscAbortSRB(), scp %x\n",
                (unsigned) scp);
            switch (AscAbortSRB(asc_dvc_varp, (ulong) scp)) {
            case ASC_TRUE:
                /* asc_isr_callback() will be called */
                ASC_DBG(1, "advansys_abort: AscAbortSRB() TRUE\n");
                ret = SCSI_ABORT_PENDING;
                break;
            case ASC_FALSE:
                /* Request has apparently already completed. */
                ASC_DBG(1, "advansys_abort: AscAbortSRB() FALSE\n");
                ret = SCSI_ABORT_NOT_RUNNING;
                break;
            case ASC_ERROR:
            default:
                ASC_DBG(1, "advansys_abort: AscAbortSRB() ERROR\n");
                ret = SCSI_ABORT_ERROR;
                break;
            }
            cli();

            /*
             * The request will either still be on the active queue
             * or have been added to the board's done queue.
             */
            if (asc_rmqueue(&boardp->active, scp) == ASC_TRUE) {
                scp->result = HOST_BYTE(DID_ABORT);
                scp_found = ASC_TRUE;
            } else {
                scp_found = asc_rmqueue(&boardp->done, scp);
                ASC_ASSERT(scp_found == ASC_TRUE);
            }

        } else {
            /*
             * The command was not found on the active or waiting queues.
             */
            do_scsi_done = ASC_TRUE;
            scp_found = ASC_FALSE;
            ret = SCSI_ABORT_NOT_RUNNING;
        }

        /* Clear abort flag. */
        boardp->flags &= ~ASC_HOST_IN_ABORT;

        /*
         * Because the ASC_HOST_IN_ABORT flag causes both
         * 'advansys_interrupt' and 'asc_isr_callback' to
         * queue requests to the board's 'done' queue and
         * prevents waiting commands from being executed,
         * these queued requests must be handled here.
         */
        done_scp = asc_dequeue_list(&boardp->done, NULL, ASC_TID_ALL);

        /*
         * Start any waiting commands for the board.
         */
        if (!ASC_QUEUE_EMPTY(&boardp->waiting)) {
            ASC_DBG(1, "advansys_interrupt: before asc_execute_queue()\n");
            asc_execute_queue(&boardp->waiting);
        }
    }

    /* Interrupts could be enabled here. */

    /*
     * Complete the request to be aborted, unless it has been
     * restarted as detected above, even if it was not found on
     * the device active or waiting queues.
     */
    ASC_ASSERT(do_scsi_done != ASC_ERROR);
    ASC_ASSERT(scp_found != ASC_ERROR);
    if (do_scsi_done == ASC_TRUE) {
        if (scp->scsi_done == NULL) {
            ASC_PRINT1(
"advansys_abort: aborted request scsi_done() is NULL, %x\n",
                (unsigned) scp);
        } else {
            if (scp_found == ASC_FALSE) {
                ASC_PRINT1(
"advansys_abort: abort request not active or waiting, completing anyway %x\n",
                    (unsigned) scp);
            }
            ASC_STATS(scp->host, done);
            scp->scsi_done(scp);
        }
    }

    /*
     * It is possible for the request done function to re-enable
     * interrupts without confusing the driver. But here interrupts
     * aren't enabled until all requests have been completed.
     */
    if (done_scp != NULL) {
        asc_scsi_done_list(done_scp);
    }

    ASC_DBG1(1, "advansys_abort: ret %d\n", ret);

    /* Re-enable interrupts, if they were enabled on entry. */
    restore_flags(flags);

    ASC_ASSERT(ret != ASC_ERROR);
    return ret;
}

/*
 * advansys_reset()
 *
 * Reset the device associated with the command 'scp'.
 */
int
#if LINUX_VERSION_CODE < ASC_LINUX_VERSION(1,3,89)
advansys_reset(Scsi_Cmnd *scp)
#else /* version >= v1.3.89 */
advansys_reset(Scsi_Cmnd *scp, unsigned int reset_flags)
#endif /* version >= v1.3.89 */
{
    struct Scsi_Host     *shp;
    asc_board_t          *boardp;
    ASC_DVC_VAR          *asc_dvc_varp;
    int                  flags;
    Scsi_Cmnd            *done_scp = NULL, *last_scp = NULL;
    Scsi_Cmnd            *tscp, *new_last_scp;
    int                  do_scsi_done;
    int                  scp_found;
    int                  status;
    int                  target;
    int                  ret;

    /* Save current flags and disable interrupts. */
    save_flags(flags);
    cli();

    ASC_DBG1(1, "advansys_reset: %x\n", (unsigned) scp);

#ifdef ADVANSYS_STATS
    if (scp->host != NULL) {
        ASC_STATS(scp->host, reset);
    }    
#endif /* ADVANSYS_STATS */

#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,89)
    if ((reset_flags & SCSI_RESET_ASYNCHRONOUS) &&
        (scp->serial_number != scp->serial_number_at_timeout)) {
        ASC_PRINT1(
"advansys_reset: timeout serial number changed for request %x\n",
            (unsigned) scp);
        do_scsi_done = ASC_FALSE;
        scp_found = ASC_FALSE;
        ret = SCSI_RESET_NOT_RUNNING;
    } else
#endif /* version >= v1.3.89 */
    if ((shp = scp->host) == NULL) {
        scp->result = HOST_BYTE(DID_ERROR);
        do_scsi_done = ASC_TRUE;
        scp_found = ASC_FALSE;
        ret = SCSI_RESET_ERROR;
    } else if ((boardp = ASC_BOARDP(shp))->flags & 
                (ASC_HOST_IN_RESET | ASC_HOST_IN_ABORT)) {
        ASC_PRINT2(
"advansys_reset: board %d: Nested host reset or abort, flags 0x%x\n",
            boardp->id, boardp->flags);
        do_scsi_done = ASC_TRUE;
        if ((asc_rmqueue(&boardp->active, scp) == ASC_TRUE) ||
            (asc_rmqueue(&boardp->waiting, scp) == ASC_TRUE)) {
            scp_found = ASC_TRUE;
        } else {
            scp_found = ASC_FALSE;
        }
        scp->result = HOST_BYTE(DID_ERROR);
        ret = SCSI_RESET_ERROR;
    } else if (jiffies >= boardp->last_reset &&
               jiffies < (boardp->last_reset + (10 * HZ))) {
        /*
         * Don't allow a reset to be attempted within 10 seconds
         * of the last reset.
         *
         * If 'jiffies' wrapping occurs, the reset request will go
         * through, because a wrapped 'jiffies' would not pass the
         * test above.
         */
        ASC_DBG(1,
            "advansys_reset: reset within 10 sec of last reset ignored\n");
        do_scsi_done = ASC_TRUE;
        if ((asc_rmqueue(&boardp->active, scp) == ASC_TRUE) ||
            (asc_rmqueue(&boardp->waiting, scp) == ASC_TRUE)) {
            scp_found = ASC_TRUE;
        } else {
            scp_found = ASC_FALSE;
        }
        scp->result = HOST_BYTE(DID_ERROR);
        ret = SCSI_RESET_ERROR;
    } else {
        int device_reset = ASC_FALSE;

        do_scsi_done = ASC_TRUE;

        /* Set reset flag to avoid nested reset or abort requests. */
        boardp->flags |= ASC_HOST_IN_RESET;

        /*
          * If the request is on the target waiting or active queue
         * or the board done queue, then remove it and note that it
         * was found.
         */
        if (asc_rmqueue(&boardp->active, scp) == ASC_TRUE) {
            ASC_DBG(1, "advansys_reset: active scp_found = TRUE\n");
            scp_found = ASC_TRUE;
        } else if (asc_rmqueue(&boardp->waiting, scp) == ASC_TRUE) {
            ASC_DBG(1, "advansys_reset: waiting scp_found = TRUE\n");
            scp_found = ASC_TRUE;
        } else if (asc_rmqueue(&boardp->done, scp) == ASC_TRUE) {
            scp_found = ASC_TRUE;
        } else {
            scp_found = ASC_FALSE;
        }

        /*
         * If the suggest reset bus flags are set, reset the bus.
         * Otherwise only reset the device.
         */
        asc_dvc_varp = &boardp->asc_dvc_var;
#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,89)
        if (reset_flags &
            (SCSI_RESET_SUGGEST_BUS_RESET | SCSI_RESET_SUGGEST_HOST_RESET)) {
#endif /* version >= v1.3.89 */

            /*
             * Reset the target's SCSI bus.
             */
            ASC_DBG(1, "advansys_reset: before AscResetSB()\n");
            sti();    /* Enable interrupts for AscResetSB(). */
            status = AscResetSB(asc_dvc_varp);
            cli();
            switch (status) {
            case ASC_TRUE:
                ASC_DBG(1, "advansys_reset: AscResetSB() success\n");
                ret = SCSI_RESET_SUCCESS;
                break;
            case ASC_ERROR:
            default:
                ASC_DBG(1, "advansys_reset: AscResetSB() failed\n");
                ret = SCSI_RESET_ERROR;
                break;
            }

#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,89)
        } else {
            /*
             * Reset the specified device. If the device reset fails,
             * then reset the SCSI bus.
             */

            ASC_DBG1(1, "advansys_reset: before AscResetDevice(), target %d\n",
                scp->target);
            sti();    /* Enable interrupts for AscResetDevice(). */
            status = AscResetDevice(asc_dvc_varp, scp->target);
            cli();

            /*
             * If the device has been reset, try to initialize it.
             */
            if (status == ASC_TRUE) {
                status = asc_init_dev(asc_dvc_varp, scp);
            }

            switch (status) {
            case ASC_TRUE:
                ASC_DBG(1, "advansys_reset: AscResetDevice() success\n");
                device_reset = ASC_TRUE;
                ret = SCSI_RESET_SUCCESS;
                break;
            case ASC_ERROR:
            default:
                ASC_DBG(1,
"advansys_reset: AscResetDevice() failed; Calling AscResetSB()\n");
                sti();    /* Enable interrupts for AscResetSB(). */
                status = AscResetSB(asc_dvc_varp);
                cli();
                switch (status) {
                case ASC_TRUE:
                    ASC_DBG(1, "advansys_reset: AscResetSB() TRUE\n");
                    ret = SCSI_RESET_SUCCESS;
                    break;
                case ASC_ERROR:
                default:
                    ASC_DBG(1, "advansys_reset: AscResetSB() ERROR\n");
                    ret = SCSI_RESET_ERROR;
                    break;
                }
                break;
            }
        }
#endif /* version >= v1.3.89 */

        /*
         * Because the ASC_HOST_IN_RESET flag causes both
         * 'advansys_interrupt' and 'asc_isr_callback' to
         * queue requests to the board's 'done' queue and
         * prevents waiting commands from being executed,
         * these queued requests must be handled here.
         */
        done_scp = asc_dequeue_list(&boardp->done, &last_scp,
                                    ASC_TID_ALL);

        /*
         * If a device reset was performed dequeue all waiting
         * and active requests for the device and set the request
         * status to DID_RESET.
         *
         * If a SCSI bus reset was performed dequeue all waiting
         * and active requests for all devices and set the request
         * status to DID_RESET.
         */
        if (device_reset == ASC_TRUE) {
            target = scp->target;
        } else {
            target = ASC_TID_ALL;
        }

        /*
         * Add active requests to 'done_scp' and set the request status
         * to DID_RESET.
         */
        if (done_scp == NULL) {
            done_scp = asc_dequeue_list(&boardp->active, &last_scp, target);
            for (tscp = done_scp; tscp; tscp = REQPNEXT(tscp)) {
                tscp->result = HOST_BYTE(DID_RESET);
            }
        } else {
            ASC_ASSERT(last_scp != NULL);
            REQPNEXT(last_scp) = asc_dequeue_list(&boardp->active,
                &new_last_scp, target);
            if (new_last_scp != NULL) {
                ASC_ASSERT(REQPNEXT(last_scp) != NULL);
                for (tscp = REQPNEXT(last_scp); tscp; tscp = REQPNEXT(tscp)) {
                    tscp->result = HOST_BYTE(DID_RESET);
                }
                last_scp = new_last_scp;
            }
        }

        /*
         * Add waiting requests to 'done_scp' and set the request status
         * to DID_RESET.
         */
        if (done_scp == NULL) {
            done_scp = asc_dequeue_list(&boardp->waiting, &last_scp, target);
            for (tscp = done_scp; tscp; tscp = REQPNEXT(tscp)) {
                tscp->result = HOST_BYTE(DID_RESET);
            }
        } else {
            ASC_ASSERT(last_scp != NULL);
            REQPNEXT(last_scp) = asc_dequeue_list(&boardp->waiting,
                &new_last_scp, target);
            if (new_last_scp != NULL) {
                ASC_ASSERT(REQPNEXT(last_scp) != NULL);
                for (tscp = REQPNEXT(last_scp); tscp; tscp = REQPNEXT(tscp)) {
                    tscp->result = HOST_BYTE(DID_RESET);
                }
                last_scp = new_last_scp;
            }
        }

        /* Save the time of the most recently completed reset. */
        boardp->last_reset = jiffies;

        /* Clear reset flag. */
        boardp->flags &= ~ASC_HOST_IN_RESET;

        /*
         * Start any waiting commands for the board.
         */
        if (!ASC_QUEUE_EMPTY(&boardp->waiting)) {
            ASC_DBG(1, "advansys_interrupt: before asc_execute_queue()\n");
            asc_execute_queue(&boardp->waiting);
        }
        ret = SCSI_RESET_SUCCESS;
    }

    /* Interrupts could be enabled here. */

    ASC_ASSERT(do_scsi_done != ASC_ERROR);
    ASC_ASSERT(scp_found != ASC_ERROR);
    if (do_scsi_done == ASC_TRUE) {
        if (scp->scsi_done == NULL) {
            ASC_PRINT1(
"advansys_reset: reset request scsi_done() is NULL, %x\n",
                (unsigned) scp);
        } else {
            if (scp_found == ASC_FALSE) {
                ASC_PRINT1(
"advansys_reset: reset request not active or waiting, completing anyway %x\n",
                    (unsigned) scp);
            }
            ASC_STATS(scp->host, done);
            scp->scsi_done(scp);
        }
    }

    /*
     * It is possible for the request done function to re-enable
     * interrupts without confusing the driver. But here interrupts
     * aren't enabled until requests have been completed.
     */
    if (done_scp != NULL) {
        asc_scsi_done_list(done_scp);
    }

    ASC_DBG1(1, "advansys_reset: ret %d", ret);

    /* Re-enable interrupts, if they were enabled on entry. */
    restore_flags(flags);

    ASC_ASSERT(ret != ASC_ERROR);
    return ret;
}

/*
 * advansys_biosparam()
 *
 * Translate disk drive geometry if the "BIOS greater than 1 GB"
 * support is enabled for a drive.
 *
 * ip (information pointer) is an int array with the following definition:
 * ip[0]: heads
 * ip[1]: sectors
 * ip[2]: cylinders
 */
int
#if LINUX_VERSION_CODE < ASC_LINUX_VERSION(1,3,0)
advansys_biosparam(Disk *dp, int dep, int ip[])
#else /* version >= v1.3.0 */
advansys_biosparam(Disk *dp, kdev_t dep, int ip[])
#endif /* version >= v1.3.0 */
{
    ASC_DBG(1, "advansys_biosparam: begin\n");
    ASC_STATS(dp->device->host, biosparam);
    if ((ASC_BOARDP(dp->device->host)->asc_dvc_var.dvc_cntl &
         ASC_CNTL_BIOS_GT_1GB) && dp->capacity > 0x200000) {
            ip[0] = 255;
            ip[1] = 63;
    } else {
            ip[0] = 64;
            ip[1] = 32;
    }
    ip[2] = dp->capacity / (ip[0] * ip[1]);
    ASC_DBG(1, "advansys_biosparam: end\n");
    return 0;
}

/*
 * advansys_setup()
 *
 * This function is called from init/main.c at boot time.
 * It it passed LILO parameters that can be set from the
 * LILO command line or in /etc/lilo.conf.
 *
 * It is used by the AdvanSys driver to either disable I/O
 * port scanning or to limit scanning to 1 - 4 I/O ports.
 * Regardless of the option setting EISA and PCI boards
 * will still be searched for and detected. This option
 * only affects searching for ISA and VL boards.
 *
 * If ADVANSYS_DEBUG is defined the driver debug level may
 * be set using the 5th (ASC_NUM_BOARD_SUPPORTED + 1) I/O Port.
 *
 * Examples:
 * 1. Eliminate I/O port scanning:
 *         boot: linux advansys=
 *       or
 *         boot: linux advansys=0x0
 * 2. Limit I/O port scanning to one I/O port:
 *        boot: linux advansys=0x110
 * 3. Limit I/O port scanning to four I/O ports:
 *        boot: linux advansys=0x110,0x210,0x230,0x330
 * 4. If ADVANSYS_DEBUG, limit I/O port scanning to four I/O ports and
 *    set the driver debug level to 2.
 *        boot: linux advansys=0x110,0x210,0x230,0x330,0xdeb2
 *
 * ints[0] - number of arguments
 * ints[1] - first argument
 * ints[2] - second argument
 * ...
 */
ASC_INITFUNC(
void
advansys_setup(char *str, int *ints)
)
{
    int    i;

    if (asc_iopflag == ASC_TRUE) {
        printk("AdvanSys SCSI: 'advansys' LILO option may appear only once\n");
        return;
    }

    asc_iopflag = ASC_TRUE;

    if (ints[0] > ASC_NUM_BOARD_SUPPORTED) {
#ifdef ADVANSYS_DEBUG
        if ((ints[0] == ASC_NUM_BOARD_SUPPORTED + 1) &&
            (ints[ASC_NUM_BOARD_SUPPORTED + 1] >> 4 == 0xdeb)) {
            asc_dbglvl = ints[ASC_NUM_BOARD_SUPPORTED + 1] & 0xf;
        } else {
#endif /* ADVANSYS_DEBUG */
            printk("AdvanSys SCSI: only %d I/O ports accepted\n",
                ASC_NUM_BOARD_SUPPORTED);
#ifdef ADVANSYS_DEBUG
        }
#endif /* ADVANSYS_DEBUG */
    }

#ifdef ADVANSYS_DEBUG
    ASC_DBG1(1, "advansys_setup: ints[0] %d\n", ints[0]);
    for (i = 1; i < ints[0]; i++) {
        ASC_DBG2(1, " ints[%d] %x", i, ints[i]);
    }
    ASC_DBG(1, "\n");
#endif /* ADVANSYS_DEBUG */

    for (i = 1; i <= ints[0] && i <= ASC_NUM_BOARD_SUPPORTED; i++) {
        asc_ioport[i-1] = ints[i];
        ASC_DBG2(1, "advansys_setup: asc_ioport[%d] %x\n",
            i - 1, asc_ioport[i-1]);
    }
}


/*
 * --- Loadable Driver Support
 */

#ifdef MODULE
Scsi_Host_Template driver_template = ADVANSYS;
# include "scsi_module.c"
#endif /* MODULE */


/*
 * --- Miscellaneous Driver Functions
 */

/*
 * First-level interrupt handler.
 *
 * For versions > v1.3.70, 'dev_id' is a pointer to the interrupting
 * adapter's asc_board_t. Because all boards are currently checked
 * for interrupts on each interrupt, 'dev_id' is not referenced. 'dev_id'
 * could be used to identify an interrupt passed to the AdvanSys driver,
 * which is for a device sharing an interrupt with an AdvanSys adapter.
 */
STATIC void
#if LINUX_VERSION_CODE < ASC_LINUX_VERSION(1,3,70)
advansys_interrupt(int irq, struct pt_regs *regs)
#else /* version >= v1.3.70 */
advansys_interrupt(int irq, void *dev_id, struct pt_regs *regs)
#endif /* version >= v1.3.70 */
{
    int             flags;
    int             i;
    asc_board_t     *boardp;
    Scsi_Cmnd       *done_scp = NULL, *last_scp = NULL;
    Scsi_Cmnd       *new_last_scp;

    /* Disable interrupts, if they aren't already disabled. */
    save_flags(flags);
    cli();

    ASC_DBG(1, "advansys_interrupt: begin\n");
    /*
     * Check for interrupts on all boards.
     * AscISR() will call asc_isr_callback().
     */
    for (i = 0; i < asc_board_count; i++) {
        ASC_STATS(asc_host[i], check_interrupt);
        boardp = ASC_BOARDP(asc_host[i]);
        while (AscIsIntPending(asc_host[i]->io_port)) {
            ASC_STATS(asc_host[i], interrupt);
            ASC_DBG(1, "advansys_interrupt: before AscISR()\n");
            AscISR(&boardp->asc_dvc_var);
        }

        /*
         * Start waiting requests and create a list of completed requests.
         * 
         * If a reset or abort request is being performed for the board,
         * the reset or abort handler will complete pending requests after
         * it has completed.
         */
        if ((boardp->flags & (ASC_HOST_IN_RESET | ASC_HOST_IN_ABORT)) == 0) {
            /* Start any waiting commands for the board. */
            if (!ASC_QUEUE_EMPTY(&boardp->waiting)) {
                ASC_DBG(1, "advansys_interrupt: before asc_execute_queue()\n");
                asc_execute_queue(&boardp->waiting);
            }

             /*
             * Add to the list of requests that must be completed.
             */
            if (done_scp == NULL) {
                done_scp = asc_dequeue_list(&boardp->done, &last_scp,
                    ASC_TID_ALL);
            } else {
                ASC_ASSERT(last_scp != NULL);
                REQPNEXT(last_scp) = asc_dequeue_list(&boardp->done,
                    &new_last_scp, ASC_TID_ALL);
                if (new_last_scp != NULL) {
                    ASC_ASSERT(REQPNEXT(last_scp) != NULL);
                    last_scp = new_last_scp;
                }
            }
        }
    }

    /* Interrupts could be enabled here. */

    /*
     * It is possible for the request done function to re-enable
     * interrupts without confusing the driver. But here interrupts
     * aren't enabled until all requests have been completed.
     */
    asc_scsi_done_list(done_scp);

    /* Re-enable interrupts, if they were enabled on entry. */
    restore_flags(flags);

    ASC_DBG(1, "advansys_interrupt: end\n");
    return;
}

#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,89)
/*
 * Set the number of commands to queue per device for the
 * specified host adapter.
 */
STATIC void
advansys_select_queue_depths(struct Scsi_Host *shp, Scsi_Device *devicelist)
{
    Scsi_Device        *device;
    asc_board_t        *boardp;

    boardp = ASC_BOARDP(shp);
    for (device = devicelist; device != NULL; device = device->next) {
        if (device->host != shp) {
            continue;
        }
        /*
         * Save a pointer to the device and set its initial/maximum
         * queue depth.
         */
        boardp->device[device->id] = device;
        device->queue_depth = boardp->asc_dvc_var.max_dvc_qng[device->id];
        ASC_DBG3(1, "advansys_select_queue_depths: shp %x, id %d, depth %d\n",
            (unsigned) shp, device->id, device->queue_depth);
    }
}
#endif /* version >= v1.3.89 */

/*
 * Function used only with polled I/O requests that are initiated by
 * advansys_command().
 */
STATIC void
advansys_command_done(Scsi_Cmnd *scp)
{
    ASC_DBG1(1, "advansys_command_done: scp %x\n", (unsigned) scp);
    scp->SCp.Status = 1;
}

/*
 * Complete all requests on the singly linked list pointed
 * to by 'scp'.
 *
 * Interrupts can be enabled on entry.
 */
STATIC void
asc_scsi_done_list(Scsi_Cmnd *scp)
{
    Scsi_Cmnd    *tscp;

    while (scp != NULL) {
        tscp = REQPNEXT(scp);
        REQPNEXT(scp) = NULL;
        ASC_STATS(scp->host, done);
        ASC_ASSERT(scp->scsi_done != NULL);
        scp->scsi_done(scp);
        scp = tscp;
    }
    return;
}

/*
 * Execute a single 'Scsi_Cmnd'.
 *
 * The function 'done' is called when the request has been completed.
 *
 * Scsi_Cmnd:
 *
 *  host - board controlling device
 *  device - device to send command
 *  target - target of device
 *  lun - lun of device
 *  cmd_len - length of SCSI CDB
 *    cmnd - buffer for SCSI 8, 10, or 12 byte CDB
 *  use_sg - if non-zero indicates scatter-gather request with use_sg elements
 *
 *  if (use_sg == 0)
 *        request_buffer - buffer address for request
 *        request_bufflen - length of request buffer
 *  else
 *        request_buffer - pointer to scatterlist structure
 *
 *  sense_buffer - sense command buffer
 *
 *  result (4 bytes of an int):
 *   Byte Meaning
 *   0      SCSI Status Byte Code
 *   1      SCSI One Byte Message Code
 *   2       Host Error Code
 *   3      Mid-Level Error Code
 *
 *  host driver fields:
 *  SCp - Scsi_Pointer used for command processing status
 *  scsi_done - used to save caller's done function
 *     host_scribble - used for pointer to another Scsi_Cmnd
 *
 * If this function returns ASC_NOERROR or ASC_ERROR the request
 * has been enqueued on the board's 'done' queue and must be
 * completed by the caller.
 *
 * If ASC_BUSY is returned the request must be enqueued by the
 * caller and re-tried later.
 */
STATIC int
asc_execute_scsi_cmnd(Scsi_Cmnd *scp)
{
    asc_board_t        *boardp;
    ASC_DVC_VAR        *asc_dvc_varp;
    Scsi_Device        *device;
    int                ret;

    ASC_ASSERT(interrupts_enabled() == ASC_FALSE);
    ASC_DBG2(1, "asc_execute_scsi_cmnd: scp %x, done %x\n",
        (unsigned) scp, (unsigned) scp->scsi_done);

    boardp = ASC_BOARDP(scp->host);
    asc_dvc_varp = &boardp->asc_dvc_var;
    device = boardp->device[scp->target];

    /*
     * If this is the first command, then initialize the device. If
     * no device is found set 'DID_BAD_TARGET' and return.
     */
    if ((boardp->init_tidmask & ASC_TIX_TO_TARGET_ID(scp->target)) == 0) {
        if (asc_init_dev(asc_dvc_varp, scp) == ASC_FALSE) {
            scp->result = HOST_BYTE(DID_BAD_TARGET);
            asc_enqueue(&boardp->done, scp, ASC_BACK);
            return ASC_ERROR;
        }
        boardp->init_tidmask |= ASC_TIX_TO_TARGET_ID(scp->target);
    }

    /*
     * Mutually exclusive access is required to 'asc_scsi_q' and
     * 'asc_sg_head' until after the request is started.
     */
    memset(&asc_scsi_q, 0, sizeof(ASC_SCSI_Q));

    /*
     * Point the ASC_SCSI_Q to the 'Scsi_Cmnd'.
     */
    asc_scsi_q.q2.srb_ptr = (ulong) scp;

    /*
     * Build the ASC_SCSI_Q request.
     */
    asc_scsi_q.cdbptr = &scp->cmnd[0];
    asc_scsi_q.q2.cdb_len = scp->cmd_len;
    asc_scsi_q.q1.target_id = ASC_TID_TO_TARGET_ID(scp->target);
    asc_scsi_q.q1.target_lun = scp->lun;
    asc_scsi_q.q2.target_ix = ASC_TIDLUN_TO_IX(scp->target, scp->lun);
#if LINUX_VERSION_CODE < ASC_LINUX_VERSION(2,0,0)
    asc_scsi_q.q1.sense_addr = (ulong) &scp->sense_buffer[0];
#else /* version >= v2.0.0 */
    asc_scsi_q.q1.sense_addr = virt_to_bus(&scp->sense_buffer[0]);
#endif /* version >= v2.0.0 */
    asc_scsi_q.q1.sense_len = sizeof(scp->sense_buffer);

    /*
     * If there are any outstanding requests for the current target,
     * then every 255th request send an ORDERED request. This heuristic
     * tries to retain the benefit of request sorting while preventing
     * request starvation. 255 is the max number of tags or pending commands
     * a device may have outstanding.
     *
     * The request count is incremented below for every successfully
     * started request.
     * 
     */
    if ((asc_dvc_varp->cur_dvc_qng[scp->target] > 0) &&
        (boardp->reqcnt[scp->target] % 255) == 0) {
        asc_scsi_q.q2.tag_code = M2_QTAG_MSG_ORDERED;
    } else {
        asc_scsi_q.q2.tag_code = M2_QTAG_MSG_SIMPLE;
    }

    /*
     * Build ASC_SCSI_Q for a contiguous buffer or a scatter-gather
     * buffer command.
     */
    if (scp->use_sg == 0) {
        /*
         * CDB request of single contiguous buffer.
         */
        ASC_STATS(scp->host, cont_cnt);
#if LINUX_VERSION_CODE < ASC_LINUX_VERSION(2,0,0)
        asc_scsi_q.q1.data_addr = (ulong) scp->request_buffer;
#else /* version >= v2.0.0 */
        asc_scsi_q.q1.data_addr = virt_to_bus(scp->request_buffer);
#endif /* version >= v2.0.0 */
        asc_scsi_q.q1.data_cnt = scp->request_bufflen;
        ASC_STATS_ADD(scp->host, cont_xfer,
                      ASC_CEILING(scp->request_bufflen, 512));
        asc_scsi_q.q1.sg_queue_cnt = 0;
        asc_scsi_q.sg_head = NULL;
    } else {
        /*
         * CDB scatter-gather request list.
         */
        int                    sgcnt;
        struct scatterlist    *slp;

        if (scp->use_sg > scp->host->sg_tablesize) {
            ASC_PRINT3(
"asc_execute_scsi_cmnd: board %d: use_sg %d > sg_tablesize %d\n",
                boardp->id, scp->use_sg, scp->host->sg_tablesize);
            scp->result = HOST_BYTE(DID_ERROR);
            asc_enqueue(&boardp->done, scp, ASC_BACK);
            return ASC_ERROR;
        }

        ASC_STATS(scp->host, sg_cnt);

        /*
         * Allocate a ASC_SG_HEAD structure and set the ASC_SCSI_Q
         * to point to it.
         */
        memset(&asc_sg_head, 0, sizeof(ASC_SG_HEAD));

        asc_scsi_q.q1.cntl |= QC_SG_HEAD;
        asc_scsi_q.sg_head = &asc_sg_head;
        asc_scsi_q.q1.data_cnt = 0;
        asc_scsi_q.q1.data_addr = 0;
        asc_sg_head.entry_cnt = asc_scsi_q.q1.sg_queue_cnt = scp->use_sg;
        ASC_STATS_ADD(scp->host, sg_elem, asc_sg_head.entry_cnt);

        /*
         * Convert scatter-gather list into ASC_SG_HEAD list.
         */
        slp = (struct scatterlist *) scp->request_buffer;
        for (sgcnt = 0; sgcnt < scp->use_sg; sgcnt++, slp++) {
#if LINUX_VERSION_CODE < ASC_LINUX_VERSION(2,0,0)
            asc_sg_head.sg_list[sgcnt].addr = (ulong) slp->address;
#else /* version >= v2.0.0 */
            asc_sg_head.sg_list[sgcnt].addr = virt_to_bus(slp->address);
#endif /* version >= v2.0.0 */
            asc_sg_head.sg_list[sgcnt].bytes = slp->length;
            ASC_STATS_ADD(scp->host, sg_xfer, ASC_CEILING(slp->length, 512));
        }
    }

    ASC_DBG_PRT_SCSI_Q(2, &asc_scsi_q);
    ASC_DBG_PRT_CDB(1, scp->cmnd, scp->cmd_len);

    /*
     * Execute the command. If there is no error, add the command
     * to the active queue.
     */
    switch (ret = AscExeScsiQueue(asc_dvc_varp, &asc_scsi_q)) {
    case ASC_NOERROR:
        ASC_STATS(scp->host, asc_noerror);
        /*
         * Increment monotonically increasing per device successful
         * request counter. Wrapping doesn't matter.
         */
        boardp->reqcnt[scp->target]++;

#if ASC_QUEUE_FLOW_CONTROL
        /*
         * Conditionally increment the device queue depth.
         *
          * If no error occurred and there have been 100 consecutive
         * successfull requests and the current queue depth is less
         * than the maximum queue depth, then increment the current
         * queue depth.
         */
        if (boardp->nerrcnt[scp->target]++ > 100) {
            boardp->nerrcnt[scp->target] = 0;
            if ((device->queue_curr_depth < device->queue_depth) &&
                (!(boardp->queue_full & ASC_TIX_TO_TARGET_ID(scp->target)) ||
                 (boardp->queue_full_cnt[scp->target] >
                  device->queue_curr_depth))) {
                device->queue_curr_depth++;
            }
        }
#endif /* ASC_QUEUE_FLOW_CONTROL */
        asc_enqueue(&boardp->active, scp, ASC_BACK);
        ASC_DBG(1, "asc_execute_scsi_cmnd: AscExeScsiQueue(), ASC_NOERROR\n");
        break;
    case ASC_BUSY:
        /* Caller must enqueue request and retry later. */
        ASC_STATS(scp->host, asc_busy);
#if ASC_QUEUE_FLOW_CONTROL
        /*
         * Clear consecutive no error counter and if possbile decrement
         * queue depth.
         */
        boardp->nerrcnt[scp->target] = 0;
        if (device->queue_curr_depth > 1) {
            device->queue_curr_depth--;
        }
#endif /* ASC_QUEUE_FLOW_CONTROL */
        break;
    case ASC_ERROR:
        ASC_PRINT2(
"asc_execute_scsi_cmnd: board %d: AscExeScsiQueue() ASC_ERROR, err_code %x\n",
            boardp->id, asc_dvc_varp->err_code);
        ASC_STATS(scp->host, asc_error);
#if ASC_QUEUE_FLOW_CONTROL
        /* Clear consecutive no error counter. */
        boardp->nerrcnt[scp->target] = 0;
#endif /* ASC_QUEUE_FLOW_CONTROL */
        scp->result = HOST_BYTE(DID_ERROR);
        asc_enqueue(&boardp->done, scp, ASC_BACK);
        break;
    default:
        ASC_PRINT2(
"asc_execute_scsi_cmnd: board %d: AscExeScsiQueue() unknown, err_code %x\n",
            boardp->id, asc_dvc_varp->err_code);
        ASC_STATS(scp->host, asc_unknown);
#if ASC_QUEUE_FLOW_CONTROL
        /* Clear consecutive no error counter. */
        boardp->nerrcnt[scp->target] = 0;
#endif /* ASC_QUEUE_FLOW_CONTROL */
        scp->result = HOST_BYTE(DID_ERROR);
        asc_enqueue(&boardp->done, scp, ASC_BACK);
        break;
    }

    ASC_DBG(1, "asc_execute_scsi_cmnd: end\n");
    ASC_ASSERT(interrupts_enabled() == ASC_FALSE);
    return ret;
}

/*
 * asc_isr_callback() - Second Level Interrupt Handler called by AscISR().
 */
STATIC void
asc_isr_callback(ASC_DVC_VAR *asc_dvc_varp, ASC_QDONE_INFO *qdonep)
{
    asc_board_t         *boardp;
    Scsi_Cmnd           *scp;
    struct Scsi_Host    *shp;
    int                 i;

    ASC_ASSERT(interrupts_enabled() == ASC_FALSE);
    ASC_DBG2(1, "asc_isr_callback: asc_dvc_varp %x, qdonep %x\n",
        (unsigned) asc_dvc_varp, (unsigned) qdonep);
    ASC_DBG_PRT_QDONE_INFO(2, qdonep);

    /*
     * Get the Scsi_Cmnd structure and Scsi_Host structure for the
     * command that has been completed.
     */
    scp = (Scsi_Cmnd *) qdonep->d2.srb_ptr;
    ASC_DBG1(1, "asc_isr_callback: scp %x\n", (unsigned) scp);
    ASC_DBG_PRT_CDB(2, scp->cmnd, scp->cmd_len);

    if (scp == NULL) {
        ASC_PRINT("asc_isr_callback: scp is NULL\n");
        return;
    }

    /*
     * If the request's host pointer is not valid, display a
     * message and return.
     */
    shp = scp->host;
    for (i = 0; i < asc_board_count; i++) {
        if (asc_host[i] == shp) {
            break;
        }
    }
    if (i == asc_board_count) {
        ASC_PRINT2("asc_isr_callback: scp %x has bad host pointer, host %x\n",
            (unsigned) scp, (unsigned) shp);
        return;
    }

    ASC_STATS(shp, callback);
    ASC_DBG1(1, "asc_isr_callback: shp %x\n", (unsigned) shp);

    /*
     * If the request isn't found on the active queue, it may
     * have been removed to handle a reset or abort request.
     * Display a message and return.
     */
    boardp = ASC_BOARDP(shp);
    if (asc_rmqueue(&boardp->active, scp) == ASC_FALSE) {
        ASC_PRINT2("asc_isr_callback: board %d: scp %x not on active queue\n",
            boardp->id, (unsigned) scp);
        return;
    }

    /*
     * 'qdonep' contains the command's ending status.
     */
    switch (qdonep->d3.done_stat) {
    case QD_NO_ERROR:
        ASC_DBG(2, "asc_isr_callback: QD_NO_ERROR\n");
        switch (qdonep->d3.host_stat) {
        case QHSTA_NO_ERROR:
            scp->result = 0;
            break;
        default:
            /* QHSTA error occurred */
            scp->result = HOST_BYTE(DID_ERROR);
            break;
        }
        break;

    case QD_WITH_ERROR:
        ASC_DBG(2, "asc_isr_callback: QD_WITH_ERROR\n");
        switch (qdonep->d3.host_stat) {
        case QHSTA_NO_ERROR:
            if (qdonep->d3.scsi_stat == SS_CHK_CONDITION) {
                ASC_DBG(2, "asc_isr_callback: SS_CHK_CONDITION\n");
                ASC_DBG_PRT_SENSE(2, scp->sense_buffer,
                    sizeof(scp->sense_buffer));
                /*
                 * Note: The 'status_byte()' macro used by target drivers
                 * defined in scsi.h shifts the status byte returned by
                 * host drivers right by 1 bit. This is why target drivers
                 * also use right shifted status byte definitions. For
                 * instance target drivers use CHECK_CONDITION, defined to
                 * 0x1, instead of the SCSI defined check condition value
                 * of 0x2. Host drivers are supposed to return the status
                 * byte as it is defined by SCSI.
                 */
                scp->result = DRIVER_BYTE(DRIVER_SENSE) |
                    STATUS_BYTE(qdonep->d3.scsi_stat); 
            } else {
                scp->result = STATUS_BYTE(qdonep->d3.scsi_stat); 
            }
            break;

        default:
            /* QHSTA error occurred */
            ASC_DBG1(2, "asc_isr_callback: host_stat %x\n",
                qdonep->d3.host_stat);
            scp->result = HOST_BYTE(DID_ERROR) | MSG_BYTE(qdonep->d3.scsi_msg) |
                STATUS_BYTE(qdonep->d3.scsi_stat);
            break;
        }
        break;

    case QD_ABORTED_BY_HOST:
        ASC_DBG(1, "asc_isr_callback: QD_ABORTED_BY_HOST\n");
        scp->result = HOST_BYTE(DID_ABORT) | MSG_BYTE(qdonep->d3.scsi_msg) |
                STATUS_BYTE(qdonep->d3.scsi_stat);
        break;

    default:
        ASC_PRINT1("asc_isr_callback: done_stat %x\n", qdonep->d3.done_stat);
        scp->result = HOST_BYTE(DID_ERROR) | MSG_BYTE(qdonep->d3.scsi_msg) |
                STATUS_BYTE(qdonep->d3.scsi_stat);
        break;
    }

    /* 
     * Because interrupts may be enabled by the 'Scsi_Cmnd' done
     * function, add the command to the end of the board's done queue.
     * The done function for the command will be called from
     * advansys_interrupt().
     */
    asc_enqueue(&boardp->done, scp, ASC_BACK);

    return;
}

/*
 * asc_init_dev()
 *
 * Perform one-time initialization of a device.
 */
STATIC int
asc_init_dev(ASC_DVC_VAR *asc_dvc_varp, Scsi_Cmnd *scp)
{
    asc_board_t             *boardp;
    ASC_SCSI_REQ_Q          *scsireqq;
    ASC_CAP_INFO            *cap_info;
    ASC_SCSI_INQUIRY        *inquiry;
    int                     found;
    ASC_SCSI_BIT_ID_TYPE    save_use_tagged_qng;
    ASC_SCSI_BIT_ID_TYPE    save_can_tagged_qng;
    int                     ret;
#ifdef ADVANSYS_DEBUG
    ASC_SCSI_BIT_ID_TYPE    tidmask; /* target id bit mask: 1 - 128 */
#endif /* ADVANSYS_DEBUG */

    ASC_DBG1(1, "asc_init_dev: target %d\n", (unsigned) scp->target);

    /* The host's target id is set in init_tidmask during initialization. */
    ASC_ASSERT(asc_dvc_varp->cfg->chip_scsi_id != scp->target);

    boardp = ASC_BOARDP(scp->host);

    /* Set-up AscInitPollTarget() arguments. */
    scsireqq = &boardp->scsireqq;
    memset(scsireqq, 0, sizeof(ASC_SCSI_REQ_Q));
    cap_info = &boardp->cap_info;
    memset(cap_info, 0, sizeof(ASC_CAP_INFO));
    inquiry = &boardp->inquiry;
    memset(inquiry, 0, sizeof(ASC_SCSI_INQUIRY));

    /*
     * XXX - AscInitPollBegin() re-initializes these fields to
     * zero. 'Or' in the new values and restore them before calling 
     * AscInitPollEnd(). Normally all targets are initialized within
     * a call to AscInitPollBegin() and AscInitPollEnd().
     */
    save_use_tagged_qng = asc_dvc_varp->use_tagged_qng;
    save_can_tagged_qng = asc_dvc_varp->cfg->can_tagged_qng;

    ASC_DBG(2, "asc_init_dev: AscInitPollBegin()\n");
    if (AscInitPollBegin(asc_dvc_varp)) {
        ASC_PRINT1("asc_init_dev: board %d: AscInitPollBegin() failed\n",
            boardp->id);
        return ASC_FALSE;
    }

    scsireqq->sense_ptr = &scsireqq->sense[0];
    scsireqq->r1.sense_len = ASC_MIN_SENSE_LEN;
    scsireqq->r1.target_id = ASC_TID_TO_TARGET_ID(scp->target);
    scsireqq->r1.target_lun = 0;
    scsireqq->r2.target_ix = ASC_TIDLUN_TO_IX(scp->target, 0);

    found = ASC_FALSE;
    ASC_DBG(2, "asc_init_dev: AscInitPollTarget()\n");
    switch (ret = AscInitPollTarget(asc_dvc_varp, scsireqq, inquiry,
        cap_info)) {
    case ASC_TRUE:
        found = ASC_TRUE;
#ifdef ADVANSYS_DEBUG
        tidmask = ASC_TIX_TO_TARGET_ID(scp->target);
        ASC_DBG2(1, "asc_init_dev: lba %lu, blk_size %lu\n",
            cap_info->lba, cap_info->blk_size);
        ASC_DBG1(1, "asc_init_dev: peri_dvc_type %x\n",
            inquiry->byte0.peri_dvc_type);
        if (asc_dvc_varp->use_tagged_qng & tidmask) {
            ASC_DBG1(1, "asc_init_dev: command queuing enabled: %d\n",
                asc_dvc_varp->max_dvc_qng[scp->target]);
        } else {
            ASC_DBG(1, "asc_init_dev: command queuing disabled\n");
        }
        if (asc_dvc_varp->init_sdtr & tidmask) {
            ASC_DBG(1, "asc_init_dev: synchronous transfers enabled\n");
        } else {
            ASC_DBG(1, "asc_init_dev: synchronous transfers disabled\n");
        }
        /* Set bit means fix disabled. */
        if (asc_dvc_varp->pci_fix_asyn_xfer & tidmask) {
            ASC_DBG(1, "asc_init_dev: synchronous transfer fix disabled\n");
        } else {
            ASC_DBG(1, "asc_init_dev: synchronous transfer fix enabled\n");
        }
#endif /* ADVANSYS_DEBUG */
        break;
    case ASC_FALSE:
        ASC_DBG(1, "asc_init_dev: no device found\n");
        break;
    case ASC_ERROR:
        ASC_PRINT1("asc_init_dev: board %d: AscInitPollTarget() ASC_ERROR\n",
                boardp->id);
        break;
    default:
        ASC_PRINT2(
"asc_init_dev: board %d: AscInitPollTarget() unknown ret %d\n",
                boardp->id, ret);
        break;
    }

    /* XXX - 'Or' in original tag bits. */
    asc_dvc_varp->use_tagged_qng |= save_use_tagged_qng;
    asc_dvc_varp->cfg->can_tagged_qng |= save_can_tagged_qng;

    ASC_DBG(2, "asc_init_dev: AscInitPollEnd()\n");
    AscInitPollEnd(asc_dvc_varp);

    ASC_DBG1(1, "asc_init_dev: found %d\n", found); 

    return found;
}

/*
 * Search for an AdvanSys PCI device in the PCI configuration space.
 */
ASC_INITFUNC(
STATIC int
asc_srch_pci_dev(PCI_DEVICE *pciDevice)
)
{
    int ret;

    ASC_DBG(2, "asc_srch_pci_dev: begin\n");

    if (pci_scan_method == -1) {
        pci_scan_method = asc_scan_method();
    }
    pciDevice->type = pci_scan_method;
    ASC_DBG1(2, "asc_srch_pci_dev: type %d\n", pciDevice->type);

    ret = asc_pci_find_dev(pciDevice);
    ASC_DBG1(2, "asc_srch_pci_dev: asc_pci_find_dev() return %d\n", ret);
    if (ret == PCI_DEVICE_FOUND) {
        pciDevice->slotNumber = pciDevice->slotFound + 1;
        pciDevice->startSlot = pciDevice->slotFound + 1;
    } else {
        if (pciDevice->bridge > pciDevice->busNumber) {
            ASC_DBG2(2, "asc_srch_pci_dev: bridge %x, busNumber %x\n",
                pciDevice->bridge, pciDevice->busNumber);
            pciDevice->busNumber++;
            pciDevice->slotNumber = 0;
            pciDevice->startSlot = 0;
            pciDevice->endSlot = 0x0f;
            ret = asc_srch_pci_dev(pciDevice);
            ASC_DBG1(2, "asc_srch_pci_dev: recursive call return %d\n", ret);
        }
    }
    ASC_DBG1(2, "asc_srch_pci_dev: return %d\n", ret);
    return ret;
}

/*
 * Determine the access method to be used for 'pciDevice'.
 */
ASC_INITFUNC(
STATIC uchar
asc_scan_method(void)
)
{
    ushort      data;
    PCI_DATA    pciData;
    uchar       type;
    uchar       slot;

    ASC_DBG(2, "asc_scan_method: begin\n");
    memset(&pciData, 0, sizeof(pciData));
    for (type = 1; type < 3; type++) {
        pciData.type = type;
        for (slot = 0; slot < PCI_MAX_SLOT; slot++) {
            pciData.slot = slot;
            data = asc_get_cfg_word(&pciData);
            if ((data != 0xFFFF) && (data != 0x0000)) {
                ASC_DBG2(4, "asc_scan_method: data %x, type %d\n", data, type);
                return (type);
            }
        }
    }
    ASC_DBG1(4, "asc_scan_method: type %d\n", type);
    return (type);
}

/*
 * Check for an AdvanSys PCI device in 'pciDevice'.
 *
 * Return PCI_DEVICE_FOUND if found, otherwise return PCI_DEVICE_NOT_FOUND.
 */
ASC_INITFUNC(
STATIC int
asc_pci_find_dev(PCI_DEVICE *pciDevice)
)
{
    PCI_DATA    pciData;
    ushort      vendorid, deviceid;
    uchar       classcode, subclass;
    uchar       lslot;

    ASC_DBG(3, "asc_pci_find_dev: begin\n");
    pciData.type = pciDevice->type;
    pciData.bus = pciDevice->busNumber;
    pciData.func = pciDevice->devFunc;
    lslot = pciDevice->startSlot;
    for (; lslot < pciDevice->endSlot; lslot++) {
        pciData.slot = lslot;
        pciData.offset = VENDORID_OFFSET;
        vendorid = asc_get_cfg_word(&pciData);
        ASC_DBG1(3, "asc_pci_find_dev: vendorid %x\n", vendorid);
        if (vendorid != 0xffff) {
            pciData.offset = DEVICEID_OFFSET;
            deviceid = asc_get_cfg_word(&pciData);
            ASC_DBG1(3, "asc_pci_find_dev: deviceid %x\n", deviceid);
            if ((vendorid == ASC_PCI_VENDORID) &&
                ((deviceid == ASC_PCI_DEVICE_ID_1100) ||
                 (deviceid == ASC_PCI_DEVICE_ID_1200) ||
                 (deviceid == ASC_PCI_DEVICE_ID_1300))) {
                pciDevice->slotFound = lslot;
                ASC_DBG(3, "asc_pci_find_dev: PCI_DEVICE_FOUND\n");
                return PCI_DEVICE_FOUND;
            } else {
                pciData.offset = SUBCLASS_OFFSET;
                subclass = asc_get_cfg_byte(&pciData);
                pciData.offset = CLASSCODE_OFFSET;
                classcode = asc_get_cfg_byte(&pciData);
                if ((classcode & PCI_BASE_CLASS_BRIDGE_DEVICE) &&
                    (subclass & PCI_SUB_CLASS_PCI_TO_PCI_BRIDGE_CONTROLLER)) {
                    pciDevice->bridge++;
                }
                ASC_DBG2(3, "asc_pci_find_dev: subclass %x, classcode %x\n",
                    subclass, classcode);
            }
        }
    }
    return PCI_DEVICE_NOT_FOUND;
}

/*
 * Read PCI configuration data into 'pciConfig'.
 */
ASC_INITFUNC(
STATIC void
asc_get_pci_cfg(PCI_DEVICE *pciDevice, PCI_CONFIG_SPACE *pciConfig)
)
{
    PCI_DATA    pciData;
    uchar       counter;
    uchar       *localConfig;

    ASC_DBG1(4, "asc_get_pci_cfg: slot found - %d\n ",
        pciDevice->slotFound);

    pciData.type = pciDevice->type;
    pciData.bus = pciDevice->busNumber;
    pciData.slot = pciDevice->slotFound;
    pciData.func = pciDevice->devFunc;
    localConfig = (uchar *) pciConfig;

    for (counter = 0; counter < sizeof(PCI_CONFIG_SPACE); counter++) {
        pciData.offset = counter;
        *localConfig = asc_get_cfg_byte(&pciData);
        ASC_DBG1(4, "asc_get_pci_cfg: byte %x\n", *localConfig);
        localConfig++;
    }
    ASC_DBG1(4, "asc_get_pci_cfg: counter %d\n", counter);
}

/*
 * Read a word (16 bits) from the PCI configuration space.
 *
 * The configuration mechanism is checked for the correct access method.
 */
ASC_INITFUNC(
STATIC ushort
asc_get_cfg_word(PCI_DATA *pciData)
)
{
    ushort   tmp;
    ulong    address;
    ulong    lbus = pciData->bus;
    ulong    lslot = pciData->slot;
    ulong    lfunc = pciData->func;
    uchar    t2CFA, t2CF8;
    ulong    t1CF8, t1CFC;

    ASC_DBG4(4, "asc_get_cfg_word: type %d, bus %lu, slot %lu, func %lu\n",
        pciData->type, lbus, lslot, lfunc);

    /*
     * Check type of configuration mechanism.
     */
    if (pciData->type == 2) {
        /*
         * Save registers to be restored later.
         */
        t2CFA = inp(0xCFA);    /* save PCI bus register */
        t2CF8 = inp(0xCF8);    /* save config space enable register */

        /*
         * Write the bus and enable registers.
         */
        /* set for type 1 cycle, if needed */
        outp(0xCFA, pciData->bus);
        /* set the function number */
        outp(0xCF8, 0x10 | (pciData->func << 1)) ;

        /*
         * Read the configuration space type 2 locations.
         */
        tmp = (ushort) inpw(0xC000 | ((pciData->slot << 8) + pciData->offset));

        outp(0xCFA, t2CFA);    /* save PCI bus register */
        outp(0xCF8, t2CF8);    /* save config space enable register */
    } else {
        /*
         * Type 1 or 3 configuration mechanism.
         *
         * Save the CONFIG_ADDRESS and CONFIG_DATA register values.
         */
        t1CF8 = inpl(0xCF8);
        t1CFC = inpl(0xCFC);

        /*
         * enable <31>, bus = <23:16>, slot = <15:11>,
         * func = <10:8>, reg = <7:2>
         */
        address = (ulong) ((lbus << 16) | (lslot << 11) |
            (lfunc << 8) | (pciData->offset & 0xFC) | 0x80000000L);

        /*
         * Write out the address to CONFIG_ADDRESS.
         */
        outpl(0xCF8, address);

        /*
         * Read in word from CONFIG_DATA.
         */
        tmp = (ushort) ((inpl(0xCFC) >>
                 ((pciData->offset & 2) * 8)) & 0xFFFF);

        /*
         * Restore registers.
         */
        outpl(0xCF8, t1CF8);
        outpl(0xCFC, t1CFC);
    }
    ASC_DBG1(4, "asc_get_cfg_word: config data: %x\n", tmp);
    return tmp;
}

/*
 * Reads a byte from the PCI configuration space.
 *
 * The configuration mechanism is checked for the correct access method.
 */
ASC_INITFUNC(
STATIC uchar
asc_get_cfg_byte(PCI_DATA *pciData)
)
{
    uchar tmp;
    ulong address;
    ulong lbus = pciData->bus, lslot = pciData->slot, lfunc = pciData->func;
    uchar t2CFA, t2CF8;
    ulong t1CF8, t1CFC;

    ASC_DBG1(4, "asc_get_cfg_byte: type: %d\n", pciData->type);

    /*
     * Check type of configuration mechanism.
     */
    if (pciData->type == 2) {
        /*
         * Save registers to be restored later.
         */
        t2CFA = inp(0xCFA);    /* save PCI bus register */
        t2CF8 = inp(0xCF8);    /* save config space enable register */

        /*
         * Write the bus and enable registers.
         */
        /* set for type 1 cycle, if needed */
        outp(0xCFA, pciData->bus);
        /* set the function number */
        outp(0xCF8, 0x10 | (pciData->func << 1));

        /*
         * Read configuration space type 2 locations.
         */
        tmp = inp(0xC000 | ((pciData->slot << 8) + pciData->offset));

        /*
         * Restore registers.
         */
        outp(0xCF8, t2CF8);    /* restore the enable register */
        outp(0xCFA, t2CFA);    /* restore PCI bus register */
    } else {
        /*
         * Type 1 or 3 configuration mechanism.
         *
         * Save CONFIG_ADDRESS and CONFIG_DATA register values.
         */
        t1CF8 = inpl(0xCF8);
        t1CFC = inpl(0xCFC);

        /*
         * enable <31>, bus = <23:16>, slot = <15:11>, func = <10:8>,
         * reg = <7:2>
         */
        address = (ulong) ((lbus << 16) | (lslot << 11) |
            (lfunc << 8) | (pciData->offset & 0xFC) | 0x80000000L);

        /*
         * Write out address to CONFIG_ADDRESS.
         */
        outpl(0xCF8, address);

        /*
         * Read in word from CONFIG_DATA.
         */
        tmp = (uchar) ((inpl(0xCFC) >> ((pciData->offset & 3) * 8)) & 0xFF);

        /*
         * Restore registers.
         */
        outpl(0xCF8, t1CF8);
        outpl(0xCFC, t1CFC);
    }
    ASC_DBG1(4, "asc_get_cfg_byte: config data: %x\n", tmp);
    return tmp;
}

/*
 * Write a byte to the PCI configuration space.
 */
ASC_INITFUNC(
STATIC void
asc_put_cfg_byte(PCI_DATA *pciData, uchar byte_data)
)
{
    ulong tmpl;
    ulong address;
    ulong lbus = pciData->bus, lslot = pciData->slot, lfunc = pciData->func;
    uchar t2CFA, t2CF8;
    ulong t1CF8, t1CFC;

    ASC_DBG2(4, "asc_put_cfg_byte: type: %d, byte_data %x\n",
        pciData->type, byte_data);

    /*
     * Check type of configuration mechanism.
     */
    if (pciData->type == 2) {

        /*
         * Save registers to be restored later.
         */
        t2CFA = inp(0xCFA);    /* save PCI bus register */
        t2CF8 = inp(0xCF8);    /* save config space enable register */

        /*
         * Write bus and enable registers.
         */
        outp(0xCFA, pciData->bus);

        /*
         * Set the function number.
         */
        outp(0xCF8, 0x10 | (pciData->func << 1));

        /*
         * Write the configuration space type 2 locations.
         */
        outp(0xC000 | ((pciData->slot << 8) + pciData->offset), byte_data);

        /*
         * Restore registers.
         */
        outp(0xCF8, t2CF8);    /* restore the enable register */
        outp(0xCFA, t2CFA);    /* restore PCI bus register    */
    } else {

        /*
         * Type 1 or 3 configuration mechanism.
         *
         * Save the CONFIG_ADDRESS and CONFIG_DATA register values.
         */
        t1CF8 = inpl(0xCF8);
        t1CFC = inpl(0xCFC);

        /*
         * enable <31>, bus = <23:16>, slot = <15:11>, func = <10:8>,
         * reg = <7:2>
         */
        address = (ulong) ((lbus << 16) | (lslot << 11) | (lfunc << 8) |
                (pciData->offset & 0xFC) | 0x80000000L);
        /*
         * Write out address to CONFIG_ADDRESS.
         */
        outpl(0xCF8, address);

        /*
         * Write double word to CONFIG_DATA preserving the bytes
         * in the double not written.
         */
        tmpl = inpl(0xCFC) & ~(0xFF << ((pciData->offset & 3) * 8));
        outpl(0xCFC, tmpl | (byte_data << ((pciData->offset & 3) * 8)));

        /*
         * Restore registers.
         */
        outpl(0xCF8, t1CF8);
        outpl(0xCFC, t1CFC);
    }
    ASC_DBG(4, "asc_put_cfg_byte: end\n");
}

/*
 * Add a 'REQP' to the end of specified queue. Set 'tidmask'
 * to indicate a command is queued for the device.
 *
 * 'flag' may be either ASC_FRONT or ASC_BACK.
 *
 * 'REQPNEXT(reqp)' returns reqp's next pointer.
 */
STATIC void
asc_enqueue(asc_queue_t *ascq, REQP reqp, int flag)
{
    int        tid;

    ASC_DBG3(2, "asc_enqueue: ascq %x, reqp %x, flag %d\n",
        (unsigned) ascq, (unsigned) reqp, flag);
    ASC_ASSERT(interrupts_enabled() == ASC_FALSE);
    ASC_ASSERT(reqp != NULL);
    ASC_ASSERT(flag == ASC_FRONT || flag == ASC_BACK);
    tid = REQPTID(reqp);
    ASC_ASSERT(tid >= 0 && tid <= ASC_MAX_TID);
    if (flag == ASC_FRONT) {
        REQPNEXT(reqp) = ascq->q_first[tid];
        ascq->q_first[tid] = reqp;
        /* If the queue was empty, set the last pointer. */
        if (ascq->q_last[tid] == NULL) {
            ascq->q_last[tid] = reqp;
        }
    } else { /* ASC_BACK */
        if (ascq->q_last[tid] != NULL) {
            REQPNEXT(ascq->q_last[tid]) = reqp;
        }
        ascq->q_last[tid] = reqp;
        REQPNEXT(reqp) = NULL;
        /* If the queue was empty, set the first pointer. */
        if (ascq->q_first[tid] == NULL) {
            ascq->q_first[tid] = reqp;
        }
    }
    /* The queue has at least one entry, set its bit. */
    ascq->q_tidmask |= ASC_TIX_TO_TARGET_ID(tid);
#ifdef ADVANSYS_STATS
    /* Maintain request queue statistics. */
    ascq->q_tot_cnt[tid]++;
    ascq->q_cur_cnt[tid]++;
    if (ascq->q_cur_cnt[tid] > ascq->q_max_cnt[tid]) {
        ascq->q_max_cnt[tid] = ascq->q_cur_cnt[tid];
        ASC_DBG2(1, "asc_enqueue: new q_max_cnt[%d] %d\n",
            tid, ascq->q_max_cnt[tid]);
    }
    REQPTIME(reqp) = REQTIMESTAMP();
#endif /* ADVANSYS_STATS */
    ASC_DBG1(1, "asc_enqueue: reqp %x\n", (unsigned) reqp);
    return;
}

/*
 * Return first queued 'REQP' on the specified queue for
 * the specified target device. Clear the 'tidmask' bit for
 * the device if no more commands are left queued for it.
 *
 * 'REQPNEXT(reqp)' returns reqp's next pointer.
 */
STATIC REQP
asc_dequeue(asc_queue_t *ascq, int tid)
{
    REQP    reqp;

    ASC_DBG2(1, "asc_dequeue: ascq %x, tid %d\n", (unsigned) ascq, tid);
    ASC_ASSERT(interrupts_enabled() == ASC_FALSE);
    ASC_ASSERT(tid >= 0 && tid <= ASC_MAX_TID);
    if ((reqp = ascq->q_first[tid]) != NULL) {
        ASC_ASSERT(ascq->q_tidmask & ASC_TIX_TO_TARGET_ID(tid));
        ascq->q_first[tid] = REQPNEXT(reqp);
        /* If the queue is empty, clear its bit and the last pointer. */
        if (ascq->q_first[tid] == NULL) {
            ascq->q_tidmask &= ~ASC_TIX_TO_TARGET_ID(tid);
            ASC_ASSERT(ascq->q_last[tid] == reqp);
            ascq->q_last[tid] = NULL;
        }
#ifdef ADVANSYS_STATS
        /* Maintain request queue statistics. */
        ascq->q_cur_cnt[tid]--;
        ASC_ASSERT(ascq->q_cur_cnt[tid] >= 0);
        REQTIMESTAT("asc_dequeue", ascq, reqp, tid);
#endif /* ADVANSYS_STATS */
    }
    ASC_DBG1(1, "asc_dequeue: reqp %x\n", (unsigned) reqp);
    return reqp;
}

/*
 * Return a pointer to a singly linked list of all the requests queued
 * for 'tid' on the 'asc_queue_t' pointed to by 'ascq'.
 *
 * If 'lastpp' is not NULL, '*lastpp' will be set to point to the 
 * the last request returned in the singly linked list.
 *
 * 'tid' should either be a valid target id or if it is ASC_TID_ALL,
 * then all queued requests are concatenated into one list and
 * returned.
 *
 * Note: If 'lastpp' is used to append a new list to the end of
 * an old list, only change the old list last pointer if '*lastpp'
 * (or the function return value) is not NULL, i.e. use a temporary
 * variable for 'lastpp' and check its value after the function return
 * before assigning it to the list last pointer.
 *
 * Unfortunately collecting queuing time statistics adds overhead to
 * the function that isn't inherent to the function's algorithm.
 */
STATIC REQP
asc_dequeue_list(asc_queue_t *ascq, REQP *lastpp, int tid)
{
    REQP    firstp, lastp;
    int     i;

    ASC_DBG2(1, "asc_dequeue_list: ascq %x, tid %d\n", (unsigned) ascq, tid);
    ASC_ASSERT(interrupts_enabled() == ASC_FALSE);
    ASC_ASSERT((tid == ASC_TID_ALL) || (tid >= 0 && tid <= ASC_MAX_TID));

    /*
     * If 'tid' is not ASC_TID_ALL, return requests only for
     * the specified 'tid'. If 'tid' is ASC_TID_ALL, return all
     * requests for all tids.
     */
    if (tid != ASC_TID_ALL) {
        /* Return all requests for the specified 'tid'. */
        if ((ascq->q_tidmask & ASC_TIX_TO_TARGET_ID(tid)) == 0) {
            /* List is empty; Set first and last return pointers to NULL. */
            firstp = lastp = NULL;
        } else {
            firstp = ascq->q_first[tid];
            lastp = ascq->q_last[tid];
            ascq->q_first[tid] = ascq->q_last[tid] = NULL;
            ascq->q_tidmask &= ~ASC_TIX_TO_TARGET_ID(tid);
#ifdef ADVANSYS_STATS
            {
                REQP reqp;
                ascq->q_cur_cnt[tid] = 0;
                for (reqp = firstp; reqp; reqp = REQPNEXT(reqp)) {
                    REQTIMESTAT("asc_dequeue_list", ascq, reqp, tid);
                }
            }
#endif /* ADVANSYS_STATS */
        }
    } else {
        /* Return all requests for all tids. */
        firstp = lastp = NULL;
        for (i = 0; i <= ASC_MAX_TID; i++) {
            if (ascq->q_tidmask & ASC_TIX_TO_TARGET_ID(i)) {
                if (firstp == NULL) {
                    firstp = ascq->q_first[i];
                    lastp = ascq->q_last[i];
                } else {
                    ASC_ASSERT(lastp != NULL);
                    REQPNEXT(lastp) = ascq->q_first[i];
                    lastp = ascq->q_last[i];
                }
                ascq->q_first[i] = ascq->q_last[i] = NULL;
                ascq->q_tidmask &= ~ASC_TIX_TO_TARGET_ID(i);
#ifdef ADVANSYS_STATS
                ascq->q_cur_cnt[i] = 0;
#endif /* ADVANSYS_STATS */
            }
        }
#ifdef ADVANSYS_STATS
        {
            REQP reqp;
            for (reqp = firstp; reqp; reqp = REQPNEXT(reqp)) {
                REQTIMESTAT("asc_dequeue_list", ascq, reqp, reqp->target);
            }
        }
#endif /* ADVANSYS_STATS */
    }
    if (lastpp) {
        *lastpp = lastp;
    }
    ASC_DBG1(1, "asc_dequeue_list: firstp %x\n", (unsigned) firstp);
    return firstp;
}

/*
 * Remove the specified 'REQP' from the specified queue for
 * the specified target device. Clear the 'tidmask' bit for the
 * device if no more commands are left queued for it.
 *
 * 'REQPNEXT(reqp)' returns reqp's the next pointer.
 *
 * Return ASC_TRUE if the command was found and removed,
 * otherwise return ASC_FALSE.
 */
STATIC int
asc_rmqueue(asc_queue_t *ascq, REQP reqp)
{
    REQP        currp, prevp;
    int         tid;
    int         ret = ASC_FALSE;

    ASC_DBG2(1, "asc_rmqueue: ascq %x, reqp %x\n",
        (unsigned) ascq, (unsigned) reqp);
    ASC_ASSERT(interrupts_enabled() == ASC_FALSE);
    ASC_ASSERT(reqp != NULL);

    tid = REQPTID(reqp);
    ASC_ASSERT(tid >= 0 && tid <= ASC_MAX_TID);

    /*
     * Handle the common case of 'reqp' being the first
     * entry on the queue.
     */
    if (reqp == ascq->q_first[tid]) {
        ret = ASC_TRUE;
        ascq->q_first[tid] = REQPNEXT(reqp);
        /* If the queue is now empty, clear its bit and the last pointer. */
        if (ascq->q_first[tid] == NULL) {
            ascq->q_tidmask &= ~ASC_TIX_TO_TARGET_ID(tid);
            ASC_ASSERT(ascq->q_last[tid] == reqp);
            ascq->q_last[tid] = NULL;
        }
    } else if (ascq->q_first[tid] != NULL) {
        ASC_ASSERT(ascq->q_last[tid] != NULL);
        /*
         * Because the case of 'reqp' being the first entry has been
         * handled above and it is known the queue is not empty, if
         * 'reqp' is found on the queue it is guaranteed the queue will
         * not become empty and that 'q_first[tid]' will not be changed.
         *
         * Set 'prevp' to the first entry, 'currp' to the second entry,
         * and search for 'reqp'.
         */
        for (prevp = ascq->q_first[tid], currp = REQPNEXT(prevp);
             currp; prevp = currp, currp = REQPNEXT(currp)) {
            if (currp == reqp) {
                ret = ASC_TRUE;
                REQPNEXT(prevp) = REQPNEXT(currp);
                REQPNEXT(reqp) = NULL;
                if (ascq->q_last[tid] == reqp) {
                    ascq->q_last[tid] = prevp;
                }
                break;
            }
        }
    }
#ifdef ADVANSYS_STATS
    /* Maintain request queue statistics. */
    if (ret == ASC_TRUE) {
        ascq->q_cur_cnt[tid]--;
        REQTIMESTAT("asc_rmqueue", ascq, reqp, tid);
    }
    ASC_ASSERT(ascq->q_cur_cnt[tid] >= 0);
#endif /* ADVANSYS_STATS */
    ASC_DBG2(1, "asc_rmqueue: reqp %x, ret %d\n", (unsigned) reqp, ret);
    return ret;
}

/*
 * If the specified 'REQP' is queued on the specified queue for
 * the specified target device, return ASC_TRUE.
 */
STATIC int
asc_isqueued(asc_queue_t *ascq, REQP reqp)
{
    REQP        treqp;
    int            tid;
    int            ret = ASC_FALSE;

    ASC_DBG2(1, "asc_isqueued: ascq %x, reqp %x\n",
        (unsigned) ascq, (unsigned) reqp);
    ASC_ASSERT(interrupts_enabled() == ASC_FALSE);
    ASC_ASSERT(reqp != NULL);

    tid = REQPTID(reqp);
    ASC_ASSERT(tid >= 0 && tid <= ASC_MAX_TID);

    for (treqp = ascq->q_first[tid]; treqp; treqp = REQPNEXT(treqp)) {
        ASC_ASSERT(ascq->q_tidmask & ASC_TIX_TO_TARGET_ID(tid));
        if (treqp == reqp) {
            ret = ASC_TRUE;
            break;
        }
    }
    ASC_DBG1(1, "asc_isqueued: ret %x\n", ret);
    return ret;
}

/*
 * Execute as many queued requests as possible for the specified queue.
 *
 * Calls asc_execute_scsi_cmnd() to execute a REQP/Scsi_Cmnd.
 */
STATIC void
asc_execute_queue(asc_queue_t *ascq)
{
    ASC_SCSI_BIT_ID_TYPE    scan_tidmask;
    REQP                    reqp;
    int                        i;

    ASC_DBG1(1, "asc_execute_queue: ascq %x\n", (unsigned) ascq);
    ASC_ASSERT(interrupts_enabled() == ASC_FALSE);
    /*
     * Execute queued commands for devices attached to
     * the current board in round-robin fashion.
     */
    scan_tidmask = ascq->q_tidmask;
    do {
        for (i = 0; i <= ASC_MAX_TID; i++) {
            if (scan_tidmask & ASC_TIX_TO_TARGET_ID(i)) {
                if ((reqp = asc_dequeue(ascq, i)) == NULL) {
                    scan_tidmask &= ~ASC_TIX_TO_TARGET_ID(i);
                } else if (asc_execute_scsi_cmnd((Scsi_Cmnd *) reqp)
                            == ASC_BUSY) {
                    scan_tidmask &= ~ASC_TIX_TO_TARGET_ID(i);
                    /* Put the request back at front of the list. */
                    asc_enqueue(ascq, reqp, ASC_FRONT);
                }
            }
        }
    } while (scan_tidmask);
    return;
}

#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,0)
/*
 * asc_prt_board_devices()
 *
 * Print driver information for devices attached to the board.
 *
 * Note: no single line should be greater than ASC_PRTLINE_SIZE,
 * cf. asc_prt_line().
 *
 * Return the number of characters copied into 'cp'. No more than
 * 'cplen' characters will be copied to 'cp'.
 */
STATIC int
asc_prt_board_devices(struct Scsi_Host *shp, char *cp, int cplen)
{
    asc_board_t        *boardp;
    int                leftlen;
    int                totlen;
    int                len;
    int                i;

    boardp = ASC_BOARDP(shp);
    leftlen = cplen;
    totlen = len = 0;

    len = asc_prt_line(cp, leftlen,
"\nDevice Information for AdvanSys SCSI Host %d:\n", shp->host_no);
    ASC_PRT_NEXT();

    len = asc_prt_line(cp, leftlen, "Target Ids Detected:");
    ASC_PRT_NEXT();
    for (i = 0; i <= ASC_MAX_TID; i++) {
        if (boardp->asc_dvc_cfg.chip_scsi_id == i) {
            continue;
        } else if (boardp->init_tidmask & ASC_TIX_TO_TARGET_ID(i)) {
            len = asc_prt_line(cp, leftlen, " %d,", i);
            ASC_PRT_NEXT();
        }
    }
    len = asc_prt_line(cp, leftlen, " (%d=Host Adapter)\n",
                       boardp->asc_dvc_cfg.chip_scsi_id);
    ASC_PRT_NEXT();

     return totlen;
}

/*
 * asc_prt_board_eeprom()
 *
 * Print board EEPROM configuration.
 *
 * Note: no single line should be greater than ASC_PRTLINE_SIZE,
 * cf. asc_prt_line().
 *
 * Return the number of characters copied into 'cp'. No more than
 * 'cplen' characters will be copied to 'cp'.
 */
STATIC int
asc_prt_board_eeprom(struct Scsi_Host *shp, char *cp, int cplen)
{
    asc_board_t        *boardp;
    ASC_DVC_VAR        *asc_dvc_varp;
    int                leftlen;
    int                totlen;
    int                len;
    ASCEEP_CONFIG      *ep;
    int                i;
    int                isa_dma_speed[] = { 10, 8, 7, 6, 5, 4, 3, 2 };

    boardp = ASC_BOARDP(shp);
    asc_dvc_varp = &boardp->asc_dvc_var;
    ep = &boardp->eep_config;

    leftlen = cplen;
    totlen = len = 0;

    len = asc_prt_line(cp, leftlen,
"\nEEPROM Settings for AdvanSys SCSI Host %d:\n", shp->host_no);
    ASC_PRT_NEXT();

    len = asc_prt_line(cp, leftlen,
" Host SCSI ID: %u, Host Queue Size: %u, Device Queue Size: %u\n",
        ep->chip_scsi_id, ep->max_total_qng, ep->max_tag_qng);
    ASC_PRT_NEXT();

    len = asc_prt_line(cp, leftlen,
" Disconnects:         ");
    ASC_PRT_NEXT();
    for (i = 0; i <= ASC_MAX_TID; i++) {
        len = asc_prt_line(cp, leftlen, " %d:%c",
            i, (ep->disc_enable & ASC_TIX_TO_TARGET_ID(i)) ? 'Y' : 'N');
        ASC_PRT_NEXT();
    }
    len = asc_prt_line(cp, leftlen, "\n");
    ASC_PRT_NEXT();

    len = asc_prt_line(cp, leftlen,
" Command Queuing:     ");
    ASC_PRT_NEXT();
    for (i = 0; i <= ASC_MAX_TID; i++) {
        len = asc_prt_line(cp, leftlen, " %d:%c",
            i, (ep->use_cmd_qng & ASC_TIX_TO_TARGET_ID(i)) ? 'Y' : 'N');
        ASC_PRT_NEXT();
    }
    len = asc_prt_line(cp, leftlen, "\n");
    ASC_PRT_NEXT();

    len = asc_prt_line(cp, leftlen,
" Start Motor:         ");
    ASC_PRT_NEXT();
    for (i = 0; i <= ASC_MAX_TID; i++) {
        len = asc_prt_line(cp, leftlen, " %d:%c",
            i, (ep->start_motor & ASC_TIX_TO_TARGET_ID(i)) ? 'Y' : 'N');
        ASC_PRT_NEXT();
    }
    len = asc_prt_line(cp, leftlen, "\n");
    ASC_PRT_NEXT();

    len = asc_prt_line(cp, leftlen,
" Synchronous Transfer:");
    ASC_PRT_NEXT();
    for (i = 0; i <= ASC_MAX_TID; i++) {
        len = asc_prt_line(cp, leftlen, " %d:%c",
            i, (ep->init_sdtr & ASC_TIX_TO_TARGET_ID(i)) ? 'Y' : 'N');
        ASC_PRT_NEXT();
    }
    len = asc_prt_line(cp, leftlen, "\n");
    ASC_PRT_NEXT();

    if (asc_dvc_varp->bus_type & ASC_IS_ISA) {
        len = asc_prt_line(cp, leftlen,
" Host ISA DMA speed:   %d MB/S\n",
            isa_dma_speed[ep->isa_dma_speed]);
        ASC_PRT_NEXT();
    }

     return totlen;
}

/*
 * asc_prt_driver_conf()
 *
 * Note: no single line should be greater than ASC_PRTLINE_SIZE,
 * cf. asc_prt_line().
 *
 * Return the number of characters copied into 'cp'. No more than
 * 'cplen' characters will be copied to 'cp'.
 */
STATIC int
asc_prt_driver_conf(struct Scsi_Host *shp, char *cp, int cplen)
{
    asc_board_t            *boardp;
    int                    leftlen;
    int                    totlen;
    int                    len;
#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,89)
    int                    i;
#endif /* version >= v1.3.89 */

    boardp = ASC_BOARDP(shp);

    leftlen = cplen;
    totlen = len = 0;

    len = asc_prt_line(cp, leftlen,
"\nLinux Driver Configuration and Information for AdvanSys SCSI Host %d:\n",
        shp->host_no);
    ASC_PRT_NEXT();

    len = asc_prt_line(cp, leftlen,
#if LINUX_VERSION_CODE < ASC_LINUX_VERSION(1,3,89)
" host_busy %u, last_reset %u, max_id %u, max_lun %u\n",
        shp->host_busy, shp->last_reset, shp->max_id, shp->max_lun);
#else /* version >= v1.3.89 */
" host_busy %u, last_reset %u, max_id %u, max_lun %u, max_channel %u\n",
        shp->host_busy, shp->last_reset, shp->max_id, shp->max_lun,
        shp->max_channel);
#endif /* version >= v1.3.89 */
    ASC_PRT_NEXT();
    
    len = asc_prt_line(cp, leftlen,
#if LINUX_VERSION_CODE < ASC_LINUX_VERSION(1,3,57)
" can_queue %d, this_id %d, sg_tablesize %u, cmd_per_lun %u\n",
        shp->can_queue, shp->this_id, shp->sg_tablesize, shp->cmd_per_lun);
#else /* version >= v1.3.57 */
" unique_id %d, can_queue %d, this_id %d, sg_tablesize %u, cmd_per_lun %u\n",
        shp->unique_id, shp->can_queue, shp->this_id, shp->sg_tablesize,
        shp->cmd_per_lun);
#endif /* version >= v1.3.57 */
    ASC_PRT_NEXT();

    len = asc_prt_line(cp, leftlen,
#if LINUX_VERSION_CODE < ASC_LINUX_VERSION(1,3,57)
" unchecked_isa_dma %d, loaded_as_module %d\n",
        shp->unchecked_isa_dma, shp->loaded_as_module);
#else /* version >= v1.3.57 */
" unchecked_isa_dma %d, use_clustering %d, loaded_as_module %d\n",
        shp->unchecked_isa_dma, shp->use_clustering, shp->loaded_as_module);
#endif /* version >= v1.3.57 */
    ASC_PRT_NEXT();

    len = asc_prt_line(cp, leftlen,
" flags %x, last_reset %x, jiffies %x\n",
        ASC_BOARDP(shp)->flags, ASC_BOARDP(shp)->last_reset, jiffies);
    ASC_PRT_NEXT();

#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,89)
    len = asc_prt_line(cp, leftlen,
" queue_depth:     ");
    ASC_PRT_NEXT();
    for (i = 0; i <= ASC_MAX_TID; i++) {
        if ((boardp->asc_dvc_cfg.chip_scsi_id == i) ||
            ((boardp->init_tidmask & ASC_TIX_TO_TARGET_ID(i)) == 0)) {
            continue;
        }
        len = asc_prt_line(cp, leftlen, " %d:%d",
            i, boardp->device[i]->queue_depth);
        ASC_PRT_NEXT();
    }
    len = asc_prt_line(cp, leftlen, "\n");
    ASC_PRT_NEXT();
#endif /* version >= v1.3.89 */

#if ASC_QUEUE_FLOW_CONTROL
    len = asc_prt_line(cp, leftlen,
" queue_curr_depth:");
    ASC_PRT_NEXT();
    for (i = 0; i <= ASC_MAX_TID; i++) {
        if ((boardp->asc_dvc_cfg.chip_scsi_id == i) ||
            ((boardp->init_tidmask & ASC_TIX_TO_TARGET_ID(i)) == 0)) {
            continue;
        }
        len = asc_prt_line(cp, leftlen, " %d:%d",
            i, boardp->device[i]->queue_curr_depth);
        ASC_PRT_NEXT();
    }
    len = asc_prt_line(cp, leftlen, "\n");
    ASC_PRT_NEXT();

    len = asc_prt_line(cp, leftlen,
" queue_count:     ");
    ASC_PRT_NEXT();
    for (i = 0; i <= ASC_MAX_TID; i++) {
        if ((boardp->asc_dvc_cfg.chip_scsi_id == i) ||
            ((boardp->init_tidmask & ASC_TIX_TO_TARGET_ID(i)) == 0)) {
            continue;
        }
        len = asc_prt_line(cp, leftlen, " %d:%d",
            i, boardp->device[i]->queue_count);
        ASC_PRT_NEXT();
    }
    len = asc_prt_line(cp, leftlen, "\n");
    ASC_PRT_NEXT();
#endif /* ASC_QUEUE_FLOW_CONTROL */

     return totlen;
}

/*
 * asc_prt_board_info()
 *
 * Print dynamic board configuration information.
 *
 * Note: no single line should be greater than ASC_PRTLINE_SIZE,
 * cf. asc_prt_line().
 *
 * Return the number of characters copied into 'cp'. No more than
 * 'cplen' characters will be copied to 'cp'.
 */
STATIC int
asc_prt_board_info(struct Scsi_Host *shp, char *cp, int cplen)
{
    asc_board_t            *boardp;
    int                    leftlen;
    int                    totlen;
    int                    len;
    ASC_DVC_VAR            *v;
    ASC_DVC_CFG            *c;
    int                    i;

    boardp = ASC_BOARDP(shp);
    v = &boardp->asc_dvc_var;
    c = &boardp->asc_dvc_cfg;

    leftlen = cplen;
    totlen = len = 0;

    len = asc_prt_line(cp, leftlen,
"\nAsc Library Configuration and Statistics for AdvanSys SCSI Host %d:\n",
    shp->host_no);
    ASC_PRT_NEXT();

    len = asc_prt_line(cp, leftlen,
" chip_version %u, lib_version %u, lib_serial_no %u, mcode_date %u\n",
        c->chip_version, c->lib_version, c->lib_serial_no, c->mcode_date);
    ASC_PRT_NEXT();

    len = asc_prt_line(cp, leftlen,
" mcode_version %u, err_code %u\n",
         c->mcode_version, v->err_code);
    ASC_PRT_NEXT();

    /* Current number of commands waiting for the host. */
    len = asc_prt_line(cp, leftlen,
" Total Command Pending:    %d\n", v->cur_total_qng);
    ASC_PRT_NEXT();

    len = asc_prt_line(cp, leftlen,
" Command Queuing:         ");
    ASC_PRT_NEXT();
    for (i = 0; i <= ASC_MAX_TID; i++) {
        if ((boardp->asc_dvc_cfg.chip_scsi_id == i) ||
            ((boardp->init_tidmask & ASC_TIX_TO_TARGET_ID(i)) == 0)) {
            continue;
        }
        len = asc_prt_line(cp, leftlen, " %d:%c",
            i, (v->use_tagged_qng & ASC_TIX_TO_TARGET_ID(i)) ? 'Y' : 'N');
        ASC_PRT_NEXT();
    }
    len = asc_prt_line(cp, leftlen, "\n");
    ASC_PRT_NEXT();

    /* Current number of commands waiting for a device. */
    len = asc_prt_line(cp, leftlen,
" Command Queue Pending:   ");
    ASC_PRT_NEXT();
    for (i = 0; i <= ASC_MAX_TID; i++) {
        if ((boardp->asc_dvc_cfg.chip_scsi_id == i) ||
            ((boardp->init_tidmask & ASC_TIX_TO_TARGET_ID(i)) == 0)) {
            continue;
        }
        len = asc_prt_line(cp, leftlen, " %d:%u", i, v->cur_dvc_qng[i]);
        ASC_PRT_NEXT();
    }
    len = asc_prt_line(cp, leftlen, "\n");
    ASC_PRT_NEXT();

    /* Current limit on number of commands that can be sent to a device. */
    len = asc_prt_line(cp, leftlen,
" Command Queue Limit:     ");
    ASC_PRT_NEXT();
    for (i = 0; i <= ASC_MAX_TID; i++) {
        if ((boardp->asc_dvc_cfg.chip_scsi_id == i) ||
            ((boardp->init_tidmask & ASC_TIX_TO_TARGET_ID(i)) == 0)) {
            continue;
        }
        len = asc_prt_line(cp, leftlen, " %d:%u", i, v->max_dvc_qng[i]);
        ASC_PRT_NEXT();
    }
    len = asc_prt_line(cp, leftlen, "\n");
    ASC_PRT_NEXT();

    /* Indicate whether the device has returned queue full status. */
    len = asc_prt_line(cp, leftlen,
" Command Queue Full:      ");
    ASC_PRT_NEXT();
    for (i = 0; i <= ASC_MAX_TID; i++) {
        if ((boardp->asc_dvc_cfg.chip_scsi_id == i) ||
            ((boardp->init_tidmask & ASC_TIX_TO_TARGET_ID(i)) == 0)) {
            continue;
        }
        if (boardp->queue_full & ASC_TIX_TO_TARGET_ID(i)) {
            len = asc_prt_line(cp, leftlen, " %d:Y-%d",
                i, boardp->queue_full_cnt[i]);
        } else {
            len = asc_prt_line(cp, leftlen, " %d:N", i);
        }
        ASC_PRT_NEXT();
    }
    len = asc_prt_line(cp, leftlen, "\n");
    ASC_PRT_NEXT();

    len = asc_prt_line(cp, leftlen,
" Synchronous Transfer:    ");
    ASC_PRT_NEXT();
    for (i = 0; i <= ASC_MAX_TID; i++) {
        if ((boardp->asc_dvc_cfg.chip_scsi_id == i) ||
            ((boardp->init_tidmask & ASC_TIX_TO_TARGET_ID(i)) == 0)) {
            continue;
        }
        len = asc_prt_line(cp, leftlen, " %d:%c",
            i, (v->sdtr_done & ASC_TIX_TO_TARGET_ID(i)) ? 'Y' : 'N');
        ASC_PRT_NEXT();
    }
    len = asc_prt_line(cp, leftlen, "\n");
    ASC_PRT_NEXT();

    for (i = 0; i <= ASC_MAX_TID; i++) {
        uchar syn_period_ix;

        if ((boardp->asc_dvc_cfg.chip_scsi_id == i) ||
            ((boardp->init_tidmask & ASC_TIX_TO_TARGET_ID(i)) == 0)) {
            continue;
        }
        if ((v->sdtr_done & ASC_TIX_TO_TARGET_ID(i)) == 0) {
            continue;
        }
        syn_period_ix = (boardp->sdtr_data[i] >> 4) & (v->max_sdtr_index - 1);
        len = asc_prt_line(cp, leftlen, "   %d:", i);
        ASC_PRT_NEXT();

        len = asc_prt_line(cp, leftlen,
            " Transfer Period Factor: %d (%d.%d Mhz),",
            v->sdtr_period_tbl[syn_period_ix],
            250 / v->sdtr_period_tbl[syn_period_ix],
            ASC_TENTHS(250, v->sdtr_period_tbl[syn_period_ix]));
        ASC_PRT_NEXT();

        len = asc_prt_line(cp, leftlen, " REQ/ACK Offset: %d\n",
            boardp->sdtr_data[i] & ASC_SYN_MAX_OFFSET);
        ASC_PRT_NEXT();
    }

     return totlen;
}

/*
 * asc_proc_copy() 
 *
 * Copy proc information to a read buffer taking into account the current
 * read offset in the file and the remaining space in the read buffer.
 */
STATIC int
asc_proc_copy(off_t advoffset, off_t offset, char *curbuf, int leftlen,
              char *cp, int cplen)
{
    int cnt = 0;
    
    ASC_DBG3(2, "asc_proc_copy: offset %d, advoffset %d, cplen %d\n",
            (unsigned) offset, (unsigned) advoffset, cplen);
    if (offset <= advoffset) {
        /* Read offset below current offset, copy everything. */
        cnt = ASC_MIN(cplen, leftlen);
        ASC_DBG3(2, "asc_proc_copy: curbuf %x, cp %x, cnt %d\n",
                (unsigned) curbuf, (unsigned) cp, cnt);
        memcpy(curbuf, cp, cnt);
    } else if (offset < advoffset + cplen) {
        /* Read offset within current range, partial copy. */
        cnt = (advoffset + cplen) - offset;
        cp = (cp + cplen) - cnt;
        cnt = ASC_MIN(cnt, leftlen);
        ASC_DBG3(2, "asc_proc_copy: curbuf %x, cp %x, cnt %d\n",
                (unsigned) curbuf, (unsigned) cp, cnt);
        memcpy(curbuf, cp, cnt);
    }
    return cnt;
}

/*
 * asc_prt_line()
 *
 * If 'cp' is NULL print to the console, otherwise print to a buffer.
 *
 * Return 0 if printing to the console, otherwise return the number of
 * bytes written to the buffer.
 *
 * Note: If any single line is greater than ASC_PRTLINE_SIZE bytes the stack
 * will be corrupted. 's[]' is defined to be ASC_PRTLINE_SIZE bytes.
 */
STATIC int
asc_prt_line(char *buf, int buflen, char *fmt, ...)
{
    va_list        args;
    int            ret;
    char        s[ASC_PRTLINE_SIZE];

    va_start(args, fmt);
    ret = vsprintf(s, fmt, args);
    ASC_ASSERT(ret < ASC_PRTLINE_SIZE);
    if (buf == NULL) {
        (void) printk(s);
        ret = 0;
    } else {
        ret = ASC_MIN(buflen, ret);
        memcpy(buf, s, ret);
    }
    va_end(args);
    return ret;
}
#endif /* version >= v1.3.0 */


/*
 * --- Functions Required by the Asc Library
 */

/*
 * Delay for 'n' milliseconds. Don't use the 'jiffies'
 * global variable which is incremented once every 5 ms
 * from a timer interrupt, because this function may be
 * called when interrupts are disabled.
 */
STATIC void
DvcSleepMilliSecond(ulong n)
{
    ulong i;

    ASC_DBG1(4, "DvcSleepMilliSecond: %lu\n", n);
    for (i = 0; i < n; i++) {
        udelay(1000);
    }
}

STATIC int
DvcEnterCritical(void)
{
    int    flags;

    save_flags(flags);
    cli();
    return flags;
}

STATIC void
DvcLeaveCritical(int flags)
{
    restore_flags(flags);
}

STATIC ulong
DvcGetSGList(ASC_DVC_VAR *asc_dvc_sg, uchar *buf_addr, ulong buf_len,
             ASC_SG_HEAD *asc_sg_head_ptr)
{
    ulong buf_size;

    buf_size = buf_len;
    asc_sg_head_ptr->entry_cnt = 1;
#if LINUX_VERSION_CODE < ASC_LINUX_VERSION(2,0,0)
    asc_sg_head_ptr->sg_list[0].addr = (ulong) buf_addr;
#else /* version >= v2.0.0 */
    asc_sg_head_ptr->sg_list[0].addr = virt_to_bus(buf_addr);
#endif /* version >= v2.0.0 */
    asc_sg_head_ptr->sg_list[0].bytes = buf_size;
    return buf_size;
}

/*
 * void
 * DvcPutScsiQ(PortAddr iop_base, ushort s_addr, ushort *outbuf, int words)
 *
 * Calling/Exit State:
 *    none
 *
 * Description:
 *     Output an ASC_SCSI_Q structure to the chip
 */
STATIC void
DvcPutScsiQ(PortAddr iop_base, ushort s_addr, ushort *outbuf, int words)
{
    int    i;

    ASC_DBG_PRT_HEX(2, "DvcPutScsiQ", (uchar *) outbuf, 2 * words);
    AscSetChipLramAddr(iop_base, s_addr);
    for (i = 0; i < words; i++, outbuf++) {
        if (i == 2 || i == 10) {
            continue;
        }
        AscSetChipLramDataNoSwap(iop_base, *outbuf);
    }
}

/*
 * void
 * DvcGetQinfo(PortAddr iop_base, ushort s_addr, ushort *inbuf, int words)
 *
 * Calling/Exit State:
 *    none
 *
 * Description:
 *     Input an ASC_QDONE_INFO structure from the chip
 */
STATIC void
DvcGetQinfo(PortAddr iop_base, ushort s_addr, ushort *inbuf, int words)
{
    int    i;

    AscSetChipLramAddr(iop_base, s_addr);
    for (i = 0; i < words; i++, inbuf++) {
        if (i == 5) {
            continue;
        }
        *inbuf = AscGetChipLramDataNoSwap(iop_base);
    }
    ASC_DBG_PRT_HEX(2, "DvcGetQinfo", (uchar *) inbuf, 2 * words);
}

/*
 * void    DvcOutPortWords(ushort iop_base, ushort &outbuf, int words)
 *
 * Calling/Exit State:
 *    none
 *
 * Description:
 *     output a buffer to an i/o port address
 */
STATIC void
DvcOutPortWords(ushort iop_base, ushort *outbuf, int words)
{
    int    i;

    for (i = 0; i < words; i++, outbuf++)
        outpw(iop_base, *outbuf);
}

/*
 * void    DvcInPortWords(ushort iop_base, ushort &outbuf, int words)
 *
 * Calling/Exit State:
 *    none
 *
 * Description:
 *     input a buffer from an i/o port address
 */
STATIC void
DvcInPortWords(ushort iop_base, ushort *inbuf, int words)
{
    int    i;

    for (i = 0; i < words; i++, inbuf++)
        *inbuf = inpw(iop_base);
}


/*
 * void DvcOutPortDWords(PortAddr port, ulong *pdw, int dwords)
 *
 * Calling/Exit State:
 *    none
 *
 * Description:
 *     output a buffer of 32-bit integers to an i/o port address in
 *  16 bit integer units
 */
STATIC void  
DvcOutPortDWords(PortAddr port, ulong *pdw, int dwords)
{
    int        i;
    int        words;
    ushort    *pw;

    pw = (ushort *) pdw;
    words = dwords << 1;
    for(i = 0; i < words; i++, pw++) {
        outpw(port, *pw);
    }
    return;
}

/*
 * Read a PCI configuration byte.
 */
ASC_INITFUNC(
STATIC uchar
DvcReadPCIConfigByte(
        ASC_DVC_VAR asc_ptr_type *asc_dvc, 
        ushort offset)
)
{
    PCI_DATA    pciData;

    pciData.bus = ASC_PCI_ID2BUS(asc_dvc->cfg->pci_slot_info);
    pciData.slot = ASC_PCI_ID2DEV(asc_dvc->cfg->pci_slot_info);
    pciData.func = ASC_PCI_ID2FUNC(asc_dvc->cfg->pci_slot_info);
    pciData.offset = offset;
    pciData.type = pci_scan_method;
    return asc_get_cfg_byte(&pciData);
}

/*
 * Write a PCI configuration byte.
 */
ASC_INITFUNC(
STATIC void
DvcWritePCIConfigByte(
        ASC_DVC_VAR asc_ptr_type *asc_dvc, 
        ushort offset, 
        uchar  byte_data)
)
{
    PCI_DATA    pciData;

    pciData.bus = ASC_PCI_ID2BUS(asc_dvc->cfg->pci_slot_info);
    pciData.slot = ASC_PCI_ID2DEV(asc_dvc->cfg->pci_slot_info);
    pciData.func = ASC_PCI_ID2FUNC(asc_dvc->cfg->pci_slot_info);
    pciData.offset = offset;
    pciData.type = pci_scan_method;
    asc_put_cfg_byte(&pciData, byte_data);
}

/*
 * Return the BIOS address of the adapter at the specified
 * I/O port and with the specified bus type.
 */
ASC_INITFUNC(
STATIC ushort
AscGetChipBiosAddress(
        PortAddr iop_base,
        ushort bus_type
)
)
{
    ushort  cfg_lsw ;
    ushort  bios_addr ;

    /*
     * The PCI BIOS is re-located by the motherboard BIOS. Because
     * of this the driver can not determine where a PCI BIOS is
     * loaded and executes.
     */
    if (bus_type & ASC_IS_PCI)
    {
        return(0);
    }

    if((bus_type & ASC_IS_EISA) != 0)
    {
        cfg_lsw = AscGetEisaChipCfg(iop_base) ;
        cfg_lsw &= 0x000F ;
        bios_addr = (ushort)(ASC_BIOS_MIN_ADDR  +
                                (cfg_lsw * ASC_BIOS_BANK_SIZE)) ;
        return(bios_addr) ;
    }/* if */

    cfg_lsw = AscGetChipCfgLsw(iop_base) ;

    /*
    *  ISA PnP uses the top bit as the 32K BIOS flag
    */
    if (bus_type == ASC_IS_ISAPNP)
    {
        cfg_lsw &= 0x7FFF;
    }/* if */

    bios_addr = (ushort)(((cfg_lsw >> 12) * ASC_BIOS_BANK_SIZE) +
            ASC_BIOS_MIN_ADDR) ;
    return(bios_addr) ;
}


/*
 * --- Tracing and Debugging Functions
 */

#ifdef ADVANSYS_STATS
/*
 * asc_prt_board_stats()
 *
 * Note: no single line should be greater than ASC_PRTLINE_SIZE,
 * cf. asc_prt_line().
 *
 * Return the number of characters copied into 'cp'. No more than
 * 'cplen' characters will be copied to 'cp'.
 */
STATIC int
asc_prt_board_stats(struct Scsi_Host *shp, char *cp, int cplen)
{
    int                    leftlen;
    int                    totlen;
    int                    len;
    struct asc_stats    *s;
    int                    i;
    asc_queue_t            *active;
    asc_queue_t            *waiting;

    leftlen = cplen;
    totlen = len = 0;

    s = &ASC_BOARDP(shp)->asc_stats;
    len = asc_prt_line(cp, leftlen,
"\nLinux Driver Statistics for AdvanSys SCSI Host %d:\n", shp->host_no);
    ASC_PRT_NEXT();
    
    len = asc_prt_line(cp, leftlen,
" command %lu, queuecommand %lu, abort %lu, reset %lu, biosparam %lu\n",
        s->command, s->queuecommand, s->abort, s->reset, s->biosparam);
    ASC_PRT_NEXT();

    len = asc_prt_line(cp, leftlen,
" check_interrupt %lu, interrupt %lu, callback %lu, done %lu\n",
        s->check_interrupt, s->interrupt, s->callback, s->done);
    ASC_PRT_NEXT();

    len = asc_prt_line(cp, leftlen,
" asc_noerror %lu, asc_busy %lu, asc_error %lu, asc_unknown %lu\n",
        s->asc_noerror, s->asc_busy, s->asc_error, s->asc_unknown);
    ASC_PRT_NEXT();

    /*
     * Display data transfer statistics.
     */
    if (s->cont_cnt > 0) {
        len = asc_prt_line(cp, leftlen, " cont_cnt %lu, ", s->cont_cnt);
        ASC_PRT_NEXT();

        len = asc_prt_line(cp, leftlen, "cont_xfer %lu.%01lu kb ",
                    s->cont_xfer/2,
                    ASC_TENTHS(s->cont_xfer, 2));
        ASC_PRT_NEXT();

        /* Contiguous transfer average size */
        len = asc_prt_line(cp, leftlen, "avg_xfer %lu.%01lu kb\n",
                    (s->cont_xfer/2)/s->cont_cnt,
                    ASC_TENTHS((s->cont_xfer/2), s->cont_cnt));
        ASC_PRT_NEXT();
    }

    if (s->sg_cnt > 0) {

        len = asc_prt_line(cp, leftlen, " sg_cnt %lu, sg_elem %lu, ",
                    s->sg_cnt, s->sg_elem);
        ASC_PRT_NEXT();

        len = asc_prt_line(cp, leftlen, "sg_xfer %lu.%01lu kb\n",
                    s->sg_xfer/2,
                    ASC_TENTHS(s->sg_xfer, 2));
        ASC_PRT_NEXT();

        /* Scatter gather transfer statistics */
        len = asc_prt_line(cp, leftlen, " avg_num_elem %lu.%01lu, ",
                    s->sg_elem/s->sg_cnt,
                    ASC_TENTHS(s->sg_elem, s->sg_cnt));
        ASC_PRT_NEXT();

        len = asc_prt_line(cp, leftlen, "avg_elem_size %lu.%01lu kb, ",
                    (s->sg_xfer/2)/s->sg_elem,
                    ASC_TENTHS((s->sg_xfer/2), s->sg_elem));
        ASC_PRT_NEXT();

        len = asc_prt_line(cp, leftlen, "avg_xfer_size %lu.%01lu kb\n",
                    (s->sg_xfer/2)/s->sg_cnt,
                    ASC_TENTHS((s->sg_xfer/2), s->sg_cnt));
        ASC_PRT_NEXT();
    }

    /*
     * Display request queuing statistics.
     */
    len = asc_prt_line(cp, leftlen,
" Active and Waiting Request Queues (time unit: %d HZ):\n", HZ);
    ASC_PRT_NEXT();

    active = &ASC_BOARDP(shp)->active;
    waiting = &ASC_BOARDP(shp)->waiting;
    for (i = 0; i < ASC_MAX_TID + 1; i++) {
        if (active->q_tot_cnt[i] > 0 || waiting->q_tot_cnt[i] > 0) {
            len = asc_prt_line(cp, leftlen, " target %d\n", i);
            ASC_PRT_NEXT();

            len = asc_prt_line(cp, leftlen,
"   active: cnt [cur %d, max %d, tot %u], time [min %d, max %d, avg %lu.%01lu]\n",
                active->q_cur_cnt[i], active->q_max_cnt[i],
                active->q_tot_cnt[i],
                active->q_min_tim[i], active->q_max_tim[i],
                (active->q_tot_cnt[i] == 0) ? 0 :
                (active->q_tot_tim[i]/active->q_tot_cnt[i]),
                (active->q_tot_cnt[i] == 0) ? 0 :
                ASC_TENTHS(active->q_tot_tim[i], active->q_tot_cnt[i]));
            ASC_PRT_NEXT();

            len = asc_prt_line(cp, leftlen,
"   waiting: cnt [cur %d, max %d, tot %u], time [min %u, max %u, avg %lu.%01lu]\n",
                waiting->q_cur_cnt[i], waiting->q_max_cnt[i],
                waiting->q_tot_cnt[i],
                waiting->q_min_tim[i], waiting->q_max_tim[i],
                (waiting->q_tot_cnt[i] == 0) ? 0 :
                (waiting->q_tot_tim[i]/waiting->q_tot_cnt[i]),
                (waiting->q_tot_cnt[i] == 0) ? 0 :
                ASC_TENTHS(waiting->q_tot_tim[i], waiting->q_tot_cnt[i]));
            ASC_PRT_NEXT();
        }
    }

     return totlen;
}
#endif /* ADVANSYS_STATS */

#ifdef ADVANSYS_DEBUG
/*
 * asc_prt_scsi_host()
 */
STATIC void 
asc_prt_scsi_host(struct Scsi_Host *s)
{
    printk("Scsi_Host at addr %x\n", (unsigned) s);
    printk(
" next %x, extra_bytes %u, host_busy %u, host_no %d, last_reset %d,\n",
        (unsigned) s->next, s->extra_bytes, s->host_busy, s->host_no,
        (unsigned) s->last_reset);

    printk(
" host_wait %x, host_queue %x, hostt %x, block %x,\n",
        (unsigned) s->host_wait, (unsigned) s->host_queue,
        (unsigned) s->hostt, (unsigned) s->block);

    printk(
" wish_block %d, base %x, io_port %d, n_io_port %d, irq %d, dma_channel %d,\n",
        s->wish_block, (unsigned) s->base, s->io_port, s->n_io_port,
        s->irq, s->dma_channel);

    printk(
" this_id %d, can_queue %d,\n", s->this_id, s->can_queue);

    printk(
" cmd_per_lun %d, sg_tablesize %d, unchecked_isa_dma %d, loaded_as_module %d\n",
        s->cmd_per_lun, s->sg_tablesize, s->unchecked_isa_dma,
        s->loaded_as_module);

    asc_prt_dvc_var(&ASC_BOARDP(s)->asc_dvc_var);
    asc_prt_dvc_cfg(&ASC_BOARDP(s)->asc_dvc_cfg);
}

/*
 * asc_prt_scsi_cmnd()
 */
STATIC void 
asc_prt_scsi_cmnd(Scsi_Cmnd *s)
{
    printk("Scsi_Cmnd at addr %x\n", (unsigned) s);

#if LINUX_VERSION_CODE < ASC_LINUX_VERSION(1,3,0)
    printk(
" host %x, device %x, target %u, lun %u\n",
        (unsigned) s->host, (unsigned) s->device, s->target, s->lun);
#else /* version >= v1.3.0 */
    printk(
" host %x, device %x, target %u, lun %u, channel %u,\n",
        (unsigned) s->host, (unsigned) s->device, s->target, s->lun,
        s->channel);
#endif /* version >= v1.3.0 */

    asc_prt_hex(" CDB", s->cmnd, s->cmd_len);

    printk(
" use_sg %u, sglist_len %u, abort_reason %x\n",
        s->use_sg, s->sglist_len, s->abort_reason);

#if LINUX_VERSION_CODE < ASC_LINUX_VERSION(1,3,89)
    printk(
" retries %d, allowed %d\n",
         s->retries, s->allowed);
#else /* version >= v1.3.89 */
    printk(
" serial_number %x, serial_number_at_timeout %x, retries %d, allowed %d\n",
        (unsigned) s->serial_number, (unsigned) s->serial_number_at_timeout,
         s->retries, s->allowed);
#endif /* version >= v1.3.89 */

    printk(
" timeout_per_command %d, timeout_total %d, timeout %d\n",
        s->timeout_per_command, s->timeout_total, s->timeout);

    printk(
" internal_timeout %u, flags %u, this_count %d\n",
        s->internal_timeout, s->flags, s->this_count);

    printk(
" scsi_done %x, done %x, host_scribble %x, result %x\n",
        (unsigned) s->scsi_done, (unsigned) s->done,
        (unsigned) s->host_scribble, s->result);

    printk(
" tag %u, pid %u\n",
        (unsigned) s->tag, (unsigned) s->pid);
}

/*
 * asc_prt_dvc_var()
 */
STATIC void 
asc_prt_dvc_var(ASC_DVC_VAR *h)
{
    printk("ASC_DVC_VAR at addr %x\n", (unsigned) h);

    printk(
" iop_base %x, err_code %x, dvc_cntl %x, bug_fix_cntl %d,\n",
        h->iop_base, h->err_code, h->dvc_cntl, h->bug_fix_cntl);

    printk(
" bus_type %d, isr_callback %x, exe_callback %x, init_sdtr %x,\n",
        h->bus_type, (unsigned) h->isr_callback, (unsigned) h->exe_callback,
        (unsigned) h->init_sdtr);

    printk(
" sdtr_done %x, use_tagged_qng %x, unit_not_ready %x, chip_no %x,\n",
        (unsigned) h->sdtr_done, (unsigned) h->use_tagged_qng,
        (unsigned) h->unit_not_ready, (unsigned) h->chip_no);
        
    printk(
" queue_full_or_busy %x, start_motor %x, scsi_reset_wait %x, irq_no %x,\n",
        (unsigned) h->queue_full_or_busy, (unsigned) h->start_motor,
        (unsigned) h->scsi_reset_wait, (unsigned) h->irq_no);

    printk(
" is_in_int %x, max_total_qng %x, cur_total_qng %x, in_critical_cnt %x,\n",
        (unsigned) h->is_in_int, (unsigned) h->max_total_qng,
        (unsigned) h->cur_total_qng, (unsigned) h->in_critical_cnt);

    printk(
" last_q_shortage %x, init_state %x, no_scam %x, pci_fix_asyn_xfer %x,\n",
        (unsigned) h->last_q_shortage, (unsigned) h->init_state,
        (unsigned) h->no_scam, (unsigned) h->pci_fix_asyn_xfer);

    printk(
" cfg %x, saved_ptr2func %x\n",
        (unsigned) h->cfg, (unsigned) h->saved_ptr2func);
}

/*
 * asc_prt_dvc_cfg()
 */
STATIC void 
asc_prt_dvc_cfg(ASC_DVC_CFG *h)
{
    printk("ASC_DVC_CFG at addr %x\n", (unsigned) h);

    printk(
" can_tagged_qng %x, cmd_qng_enabled %x, disc_enable %x, res %x,\n",
            h->can_tagged_qng, h->cmd_qng_enabled, h->disc_enable, h->res);

    printk(
" chip_scsi_id %d, isa_dma_speed %d, isa_dma_channel %d, chip_version %d,\n",
             h->chip_scsi_id, h->isa_dma_speed, h->isa_dma_channel,
             h->chip_version);

    printk(
" pci_device_id %d, lib_serial_no %d, lib_version %d, mcode_date %d,\n",
          h->pci_device_id, h->lib_serial_no, h->lib_version, h->mcode_date);

    printk(
" mcode_version %d, overrun_buf %x\n",
            h->mcode_version, (unsigned) h->overrun_buf);
}

/*
 * asc_prt_scsi_q()
 */
STATIC void 
asc_prt_scsi_q(ASC_SCSI_Q *q)
{
    ASC_SG_HEAD    *sgp;
    int i;

    printk("ASC_SCSI_Q at addr %x\n", (unsigned) q);

    printk(
" target_ix %u, target_lun %u, srb_ptr %x, tag_code %u,\n",
            q->q2.target_ix, q->q1.target_lun,
            (unsigned) q->q2.srb_ptr, q->q2.tag_code);

    printk(
" data_addr %x, data_cnt %lu, sense_addr %x, sense_len %u,\n",
            (unsigned) q->q1.data_addr, q->q1.data_cnt,
            (unsigned) q->q1.sense_addr, q->q1.sense_len);

    printk(
" cdbptr %x, cdb_len %u, sg_head %x, sg_queue_cnt %u\n",
            (unsigned) q->cdbptr, q->q2.cdb_len,
            (unsigned) q->sg_head, q->q1.sg_queue_cnt);

    if (q->sg_head) {
        sgp = q->sg_head;
        printk("ASC_SG_HEAD at addr %x\n", (unsigned) sgp);
        printk(" entry_cnt %u, queue_cnt %u\n", sgp->entry_cnt, sgp->queue_cnt);
        for (i = 0; i < sgp->entry_cnt; i++) {
            printk(" [%u]: addr %x, bytes %lu\n",
                i, (unsigned) sgp->sg_list[i].addr, sgp->sg_list[i].bytes);
        }

    }
}

/*
 * asc_prt_qdone_info()
 */
STATIC void 
asc_prt_qdone_info(ASC_QDONE_INFO *q)
{
    printk("ASC_QDONE_INFO at addr %x\n", (unsigned) q);
    printk(
" srb_ptr %x, target_ix %u, cdb_len %u, tag_code %u, done_stat %x\n",
            (unsigned) q->d2.srb_ptr, q->d2.target_ix, q->d2.cdb_len,
            q->d2.tag_code, q->d3.done_stat);
    printk(
" host_stat %x, scsi_stat %x, scsi_msg %x\n",
            q->d3.host_stat, q->d3.scsi_stat, q->d3.scsi_msg);
}

/*
 * asc_prt_hex()
 *
 * Print hexadecimal output in 4 byte groupings 32 bytes 
 * or 8 double-words per line.
 */
STATIC void 
asc_prt_hex(char *f, uchar *s, int l)
{
    int            i;
    int            j;
    int            k;
    int            m;

    printk("%s: (%d bytes)\n", f, l);

    for (i = 0; i < l; i += 32) {
        
        /* Display a maximum of 8 double-words per line. */
        if ((k = (l - i) / 4) >= 8) {
            k = 8;
            m = 0;
        } else {
            m = (l - i) % 4 ;
        }

        for (j = 0; j < k; j++) {
            printk(" %2.2X%2.2X%2.2X%2.2X",
                (unsigned) s[i+(j*4)], (unsigned) s[i+(j*4)+1],
                (unsigned) s[i+(j*4)+2], (unsigned) s[i+(j*4)+3]);
        }

        switch (m) {
        case 0:
        default:
            break;
        case 1:
            printk(" %2.2X",
                (unsigned) s[i+(j*4)]);
            break;
        case 2:
            printk(" %2.2X%2.2X",
                (unsigned) s[i+(j*4)],
                (unsigned) s[i+(j*4)+1]);
            break;
        case 3:
            printk(" %2.2X%2.2X%2.2X",
                (unsigned) s[i+(j*4)+1],
                (unsigned) s[i+(j*4)+2],
                (unsigned) s[i+(j*4)+3]);
            break;
        }

        printk("\n");
    }
}
#endif /* ADVANSYS_DEBUG */

#ifdef ADVANSYS_ASSERT
/*
 * interrupts_enabled()
 *
 * Return 1 if interrupts are enabled, otherwise return 0.
 */
STATIC int
interrupts_enabled(void)
{
    int flags;

    save_flags(flags);
    if (flags & 0x0200) {
        return ASC_TRUE;
    } else {
        return ASC_FALSE;
    }
}
#endif /* ADVANSYS_ASSERT */


/*
 * --- Asc Library Functions
 */

ASC_INITFUNC(
STATIC ushort
AscGetEisaChipCfg(
                     PortAddr iop_base
)
)
{
    PortAddr            eisa_cfg_iop;
    eisa_cfg_iop = (PortAddr) ASC_GET_EISA_SLOT(iop_base) |
      (PortAddr) (ASC_EISA_CFG_IOP_MASK);
    return (inpw(eisa_cfg_iop));
}

ASC_INITFUNC(
STATIC uchar
AscSetChipScsiID(
                    PortAddr iop_base,
                    uchar new_host_id
)
)
{
    ushort              cfg_lsw;
    if (AscGetChipScsiID(iop_base) == new_host_id) {
        return (new_host_id);
    }
    cfg_lsw = AscGetChipCfgLsw(iop_base);
    cfg_lsw &= 0xF8FF;
    cfg_lsw |= (ushort) ((new_host_id & ASC_MAX_TID) << 8);
    AscSetChipCfgLsw(iop_base, cfg_lsw);
    return (AscGetChipScsiID(iop_base));
}

ASC_INITFUNC(
STATIC uchar
AscGetChipScsiCtrl(
                      PortAddr iop_base
)
)
{
    uchar               sc;
    AscSetBank(iop_base, 1);
    sc = inp(iop_base + IOP_REG_SC);
    AscSetBank(iop_base, 0);
    return (sc);
}

ASC_INITFUNC(
STATIC uchar
AscGetChipVersion(
                     PortAddr iop_base,
                     ushort bus_type
)
)
{
    if ((bus_type & ASC_IS_EISA) != 0) {
        PortAddr            eisa_iop;
        uchar               revision;
        eisa_iop = (PortAddr) ASC_GET_EISA_SLOT(iop_base) |
          (PortAddr) ASC_EISA_REV_IOP_MASK;
        revision = inp(eisa_iop);
        return ((uchar) ((ASC_CHIP_MIN_VER_EISA - 1) + revision));
    }
    return (AscGetChipVerNo(iop_base));
}

ASC_INITFUNC(
STATIC ushort
AscGetChipBusType(
                     PortAddr iop_base
)
)
{
    ushort              chip_ver;
    chip_ver = AscGetChipVerNo(iop_base);
    if (
           (chip_ver >= ASC_CHIP_MIN_VER_VL)
           && (chip_ver <= ASC_CHIP_MAX_VER_VL)
) {
        if (
               ((iop_base & 0x0C30) == 0x0C30)
               || ((iop_base & 0x0C50) == 0x0C50)
) {
            return (ASC_IS_EISA);
        }
        return (ASC_IS_VL);
    }
    if ((chip_ver >= ASC_CHIP_MIN_VER_ISA) &&
        (chip_ver <= ASC_CHIP_MAX_VER_ISA)) {
        if (chip_ver >= ASC_CHIP_MIN_VER_ISA_PNP) {
            return (ASC_IS_ISAPNP);
        }
        return (ASC_IS_ISA);
    } else if ((chip_ver >= ASC_CHIP_MIN_VER_PCI) &&
               (chip_ver <= ASC_CHIP_MAX_VER_PCI)) {
        return (ASC_IS_PCI);
    }
    return (0);
}

ASC_INITFUNC(
STATIC ulong
AscLoadMicroCode(
                    PortAddr iop_base,
                    ushort s_addr,
                    ushort *mcode_buf,
                    ushort mcode_size
)
)
{
    ulong               chksum;
    ushort              mcode_word_size;
    ushort              mcode_chksum;
    mcode_word_size = (ushort) (mcode_size >> 1);
    AscMemWordSetLram(iop_base, s_addr, 0, mcode_word_size);
    AscMemWordCopyToLram(iop_base, s_addr, mcode_buf, mcode_word_size);
    chksum = AscMemSumLramWord(iop_base, s_addr, mcode_word_size);
    mcode_chksum = (ushort) AscMemSumLramWord(iop_base,
                                              (ushort) ASC_CODE_SEC_BEG,
          (ushort) ((mcode_size - s_addr - (ushort) ASC_CODE_SEC_BEG) / 2));
    AscWriteLramWord(iop_base, ASCV_MCODE_CHKSUM_W, mcode_chksum);
    AscWriteLramWord(iop_base, ASCV_MCODE_SIZE_W, mcode_size);
    return (chksum);
}

ASC_INITFUNC(
STATIC int
AscFindSignature(
                    PortAddr iop_base
)
)
{
    ushort              sig_word;
    if (AscGetChipSignatureByte(iop_base) == (uchar) ASC_1000_ID1B) {
        sig_word = AscGetChipSignatureWord(iop_base);
        if ((sig_word == (ushort) ASC_1000_ID0W) ||
            (sig_word == (ushort) ASC_1000_ID0W_FIX)) {
            return (1);
        }
    }
    return (0);
}

STATIC uchar _isa_pnp_inited ASC_INITDATA = 0;
STATIC PortAddr _asc_def_iop_base[ASC_IOADR_TABLE_MAX_IX] ASC_INITDATA =
{
    0x100, ASC_IOADR_1, 0x120, ASC_IOADR_2, 0x140, ASC_IOADR_3, ASC_IOADR_4,
    ASC_IOADR_5, ASC_IOADR_6, ASC_IOADR_7, ASC_IOADR_8
};

ASC_INITFUNC(
STATIC PortAddr
AscSearchIOPortAddr(
                       PortAddr iop_beg,
                       ushort bus_type
)
)
{
    if (bus_type & ASC_IS_VL) {
        while ((iop_beg = AscSearchIOPortAddr11(iop_beg)) != 0) {
            if (AscGetChipVersion(iop_beg, bus_type) <= ASC_CHIP_MAX_VER_VL) {
                return (iop_beg);
            }
        }
        return (0);
    }
    if (bus_type & ASC_IS_ISA) {
        if (_isa_pnp_inited == 0) {
            AscSetISAPNPWaitForKey();
            _isa_pnp_inited++;
        }
        while ((iop_beg = AscSearchIOPortAddr11(iop_beg)) != 0) {
            if ((AscGetChipVersion(iop_beg, bus_type) & ASC_CHIP_VER_ISA_BIT) != 0) {
                return (iop_beg);
            }
        }
        return (0);
    }
    if (bus_type & ASC_IS_EISA) {
        if ((iop_beg = AscSearchIOPortAddrEISA(iop_beg)) != 0) {
            return (iop_beg);
        }
        return (0);
    }
    return (0);
}

ASC_INITFUNC(
STATIC PortAddr
AscSearchIOPortAddr11(
                         PortAddr s_addr
)
)
{
    int                 i;
    PortAddr            iop_base;
    for (i = 0; i < ASC_IOADR_TABLE_MAX_IX; i++) {
        if (_asc_def_iop_base[i] > s_addr) {
            break;
        }
    }
    for (; i < ASC_IOADR_TABLE_MAX_IX; i++) {
        iop_base = _asc_def_iop_base[i];
        if (check_region(iop_base, ASC_IOADR_GAP) != 0) {
            ASC_DBG1(1,
               "AscSearchIOPortAddr11: check_region() failed I/O port %x\n",
                     iop_base);
            continue;
        }
        ASC_DBG1(1, "AscSearchIOPortAddr11: probing I/O port %x\n", iop_base);
        if (AscFindSignature(iop_base)) {
            return (iop_base);
        }
    }
    return (0);
}

ASC_INITFUNC(
STATIC void
AscToggleIRQAct(
                   PortAddr iop_base
)
)
{
    AscSetChipStatus(iop_base, CIW_IRQ_ACT);
    AscSetChipStatus(iop_base, 0);
    return;
}

ASC_INITFUNC(
STATIC void
AscSetISAPNPWaitForKey(
    void)
)
{
    outp(ASC_ISA_PNP_PORT_ADDR, 0x02);
    outp(ASC_ISA_PNP_PORT_WRITE, 0x02);
    return;
}

ASC_INITFUNC(
STATIC uchar
AscGetChipIRQ(
                 PortAddr iop_base,
                 ushort bus_type
)
)
{
    ushort              cfg_lsw;
    uchar               chip_irq;
    if ((bus_type & ASC_IS_EISA) != 0) {
        cfg_lsw = AscGetEisaChipCfg(iop_base);
        chip_irq = (uchar) (((cfg_lsw >> 8) & 0x07) + 10);
        if ((chip_irq == 13) || (chip_irq > 15)) {
            return (0);
        }
        return (chip_irq);
    }
    if ((bus_type & ASC_IS_VL) != 0) {
        cfg_lsw = AscGetChipCfgLsw(iop_base);
        chip_irq = (uchar) (((cfg_lsw >> 2) & 0x07));
        if ((chip_irq == 0) ||
            (chip_irq == 4) ||
            (chip_irq == 7)) {
            return (0);
        }
#if CC_PLEXTOR_VL
        if (chip_irq == 5) {
            return (9);
        }
#endif
        return ((uchar) (chip_irq + (ASC_MIN_IRQ_NO - 1)));
    }
    cfg_lsw = AscGetChipCfgLsw(iop_base);
    chip_irq = (uchar) (((cfg_lsw >> 2) & 0x03));
    if (chip_irq == 3)
        chip_irq += (uchar) 2;
    return ((uchar) (chip_irq + ASC_MIN_IRQ_NO));
}

ASC_INITFUNC(
STATIC uchar
AscSetChipIRQ(
                 PortAddr iop_base,
                 uchar irq_no,
                 ushort bus_type
)
)
{
    ushort              cfg_lsw;
    if ((bus_type & ASC_IS_VL) != 0) {
        if (irq_no != 0) {
#if CC_PLEXTOR_VL
            if (irq_no == 9) {
                irq_no = 14;
            }
#endif
            if ((irq_no < ASC_MIN_IRQ_NO) || (irq_no > ASC_MAX_IRQ_NO)) {
                irq_no = 0;
            } else {
                irq_no -= (uchar) ((ASC_MIN_IRQ_NO - 1));
            }
        }
        cfg_lsw = (ushort) (AscGetChipCfgLsw(iop_base) & 0xFFE3);
        cfg_lsw |= (ushort) 0x0010;
        AscSetChipCfgLsw(iop_base, cfg_lsw);
        AscToggleIRQAct(iop_base);
        cfg_lsw = (ushort) (AscGetChipCfgLsw(iop_base) & 0xFFE0);
        cfg_lsw |= (ushort) ((irq_no & 0x07) << 2);
        AscSetChipCfgLsw(iop_base, cfg_lsw);
        AscToggleIRQAct(iop_base);
        return (AscGetChipIRQ(iop_base, bus_type));
    }
    if ((bus_type & (ASC_IS_ISA)) != 0) {
        if (irq_no == 15)
            irq_no -= (uchar) 2;
        irq_no -= (uchar) ASC_MIN_IRQ_NO;
        cfg_lsw = (ushort) (AscGetChipCfgLsw(iop_base) & 0xFFF3);
        cfg_lsw |= (ushort) ((irq_no & 0x03) << 2);
        AscSetChipCfgLsw(iop_base, cfg_lsw);
        return (AscGetChipIRQ(iop_base, bus_type));
    }
    return (0);
}

ASC_INITFUNC(
STATIC void
AscEnableIsaDma(
                   uchar dma_channel
)
)
{
    if (dma_channel < 4) {
        outp(0x000B, (ushort) (0xC0 | dma_channel));
        outp(0x000A, dma_channel);
    } else if (dma_channel < 8) {
        outp(0x00D6, (ushort) (0xC0 | (dma_channel - 4)));
        outp(0x00D4, (ushort) (dma_channel - 4));
    }
    return;
}

STATIC int 
AscIsrChipHalted(
                    REG ASC_DVC_VAR asc_ptr_type * asc_dvc
)
{
    EXT_MSG             ext_msg;
    EXT_MSG             out_msg;
    ushort              halt_q_addr;
    int                 sdtr_accept;
    ushort              int_halt_code;
    ASC_SCSI_BIT_ID_TYPE scsi_busy;
    ASC_SCSI_BIT_ID_TYPE target_id;
    PortAddr            iop_base;
    uchar               tag_code;
    uchar               q_status;
    uchar               halt_qp;
    uchar               sdtr_data;
    uchar               target_ix;
    uchar               q_cntl, tid_no;
    uchar               cur_dvc_qng;
    uchar               asyn_sdtr;
    uchar               scsi_status;
    asc_board_t            *boardp;

    ASC_ASSERT(asc_dvc->drv_ptr != 0);
    boardp = (asc_board_t *) asc_dvc->drv_ptr;

    iop_base = asc_dvc->iop_base;
    int_halt_code = AscReadLramWord(iop_base, ASCV_HALTCODE_W);

    halt_qp = AscReadLramByte(iop_base, ASCV_CURCDB_B);
    halt_q_addr = ASC_QNO_TO_QADDR(halt_qp);
    target_ix = AscReadLramByte(iop_base,
                   (ushort) (halt_q_addr + (ushort) ASC_SCSIQ_B_TARGET_IX));
    q_cntl = AscReadLramByte(iop_base,
                        (ushort) (halt_q_addr + (ushort) ASC_SCSIQ_B_CNTL));
    tid_no = ASC_TIX_TO_TID(target_ix);
    target_id = (uchar) ASC_TID_TO_TARGET_ID(tid_no);
    if (asc_dvc->pci_fix_asyn_xfer & target_id) {

        asyn_sdtr = ASYN_SDTR_DATA_FIX_PCI_REV_AB;
    } else {
        asyn_sdtr = 0;
    }
    if (int_halt_code == ASC_HALT_DISABLE_ASYN_USE_SYN_FIX) {
        if (asc_dvc->pci_fix_asyn_xfer & target_id) {
            AscSetChipSDTR(iop_base, 0, tid_no);
            boardp->sdtr_data[tid_no] = 0;
        }
        AscWriteLramWord(iop_base, ASCV_HALTCODE_W, 0);
        return (0);
    } else if (int_halt_code == ASC_HALT_ENABLE_ASYN_USE_SYN_FIX) {
        if (asc_dvc->pci_fix_asyn_xfer & target_id) {
            AscSetChipSDTR(iop_base, asyn_sdtr, tid_no);
            boardp->sdtr_data[tid_no] = asyn_sdtr;
        }
        AscWriteLramWord(iop_base, ASCV_HALTCODE_W, 0);
        return (0);
    } else if (int_halt_code == ASC_HALT_EXTMSG_IN) {

        AscMemWordCopyFromLram(iop_base,
                               ASCV_MSGIN_BEG,
                               (ushort *) & ext_msg,
                               (ushort) (sizeof (EXT_MSG) >> 1));

        if (ext_msg.msg_type == MS_EXTEND &&
            ext_msg.msg_req == MS_SDTR_CODE &&
            ext_msg.msg_len == MS_SDTR_LEN) {
            sdtr_accept = TRUE;
            if ((ext_msg.req_ack_offset > ASC_SYN_MAX_OFFSET)) {

                sdtr_accept = FALSE;
                ext_msg.req_ack_offset = ASC_SYN_MAX_OFFSET;
            }
            if ((ext_msg.xfer_period <
                 asc_dvc->sdtr_period_tbl[asc_dvc->host_init_sdtr_index]) ||
                (ext_msg.xfer_period >
                 asc_dvc->sdtr_period_tbl[asc_dvc->max_sdtr_index])) {
                sdtr_accept = FALSE;
                ext_msg.xfer_period =
                    asc_dvc->sdtr_period_tbl[asc_dvc->host_init_sdtr_index];
            }
            if (sdtr_accept) {
                sdtr_data = AscCalSDTRData(asc_dvc, ext_msg.xfer_period,
                                           ext_msg.req_ack_offset);
                if ((sdtr_data == 0xFF)) {

                    q_cntl |= QC_MSG_OUT;
                    asc_dvc->init_sdtr &= ~target_id;
                    asc_dvc->sdtr_done &= ~target_id;
                    AscSetChipSDTR(iop_base, asyn_sdtr, tid_no);
                    boardp->sdtr_data[tid_no] = asyn_sdtr;
                }
            }
            if (ext_msg.req_ack_offset == 0) {

                q_cntl &= ~QC_MSG_OUT;
                asc_dvc->init_sdtr &= ~target_id;
                asc_dvc->sdtr_done &= ~target_id;
                AscSetChipSDTR(iop_base, asyn_sdtr, tid_no);
            } else {
                if (sdtr_accept && (q_cntl & QC_MSG_OUT)) {

                    q_cntl &= ~QC_MSG_OUT;
                    asc_dvc->sdtr_done |= target_id;
                    asc_dvc->init_sdtr |= target_id;
                    asc_dvc->pci_fix_asyn_xfer &= ~target_id;
                    sdtr_data = AscCalSDTRData(asc_dvc, ext_msg.xfer_period,
                                               ext_msg.req_ack_offset);
                    AscSetChipSDTR(iop_base, sdtr_data, tid_no);
                    boardp->sdtr_data[tid_no] = sdtr_data;
                } else {

                    q_cntl |= QC_MSG_OUT;
                    AscMsgOutSDTR(asc_dvc,
                                  ext_msg.xfer_period,
                                  ext_msg.req_ack_offset);
                    asc_dvc->pci_fix_asyn_xfer &= ~target_id;
                    sdtr_data = AscCalSDTRData(asc_dvc, ext_msg.xfer_period,
                                               ext_msg.req_ack_offset);
                    AscSetChipSDTR(iop_base, sdtr_data, tid_no);
                    boardp->sdtr_data[tid_no] = sdtr_data;
                    asc_dvc->sdtr_done |= target_id;
                    asc_dvc->init_sdtr |= target_id;
                }
            }

            AscWriteLramByte(iop_base,
                         (ushort) (halt_q_addr + (ushort) ASC_SCSIQ_B_CNTL),
                             q_cntl);
            AscWriteLramWord(iop_base, ASCV_HALTCODE_W, 0);
            return (0);
        } else if (ext_msg.msg_type == MS_EXTEND &&
                   ext_msg.msg_req == MS_WDTR_CODE &&
                   ext_msg.msg_len == MS_WDTR_LEN) {

            ext_msg.wdtr_width = 0;
            AscMemWordCopyToLram(iop_base,
                                 ASCV_MSGOUT_BEG,
                                 (ushort *) & ext_msg,
                                 (ushort) (sizeof (EXT_MSG) >> 1));
            q_cntl |= QC_MSG_OUT;
            AscWriteLramByte(iop_base,
                         (ushort) (halt_q_addr + (ushort) ASC_SCSIQ_B_CNTL),
                             q_cntl);
            AscWriteLramWord(iop_base, ASCV_HALTCODE_W, 0);
            return (0);
        } else {

            ext_msg.msg_type = M1_MSG_REJECT;
            AscMemWordCopyToLram(iop_base,
                                 ASCV_MSGOUT_BEG,
                                 (ushort *) & ext_msg,
                                 (ushort) (sizeof (EXT_MSG) >> 1));
            q_cntl |= QC_MSG_OUT;
            AscWriteLramByte(iop_base,
                         (ushort) (halt_q_addr + (ushort) ASC_SCSIQ_B_CNTL),
                             q_cntl);
            AscWriteLramWord(iop_base, ASCV_HALTCODE_W, 0);
            return (0);
        }
    } else if (int_halt_code == ASC_HALT_CHK_CONDITION) {

        q_cntl |= QC_REQ_SENSE;

#if CC_CHK_COND_REDO_SDTR
        if ((asc_dvc->init_sdtr & target_id) != 0) {

            asc_dvc->sdtr_done &= ~target_id;

            sdtr_data = AscGetMCodeInitSDTRAtID(iop_base, tid_no);
            q_cntl |= QC_MSG_OUT;
            AscMsgOutSDTR(asc_dvc,
                          asc_dvc->sdtr_period_tbl[(sdtr_data >> 4) &
                           (uchar) (asc_dvc->max_sdtr_index - 1)],
                          (uchar) (sdtr_data & (uchar) ASC_SYN_MAX_OFFSET));
        }
#endif

        AscWriteLramByte(iop_base,
                         (ushort) (halt_q_addr + (ushort) ASC_SCSIQ_B_CNTL),
                         q_cntl);

        tag_code = AscReadLramByte(iop_base,
                    (ushort) (halt_q_addr + (ushort) ASC_SCSIQ_B_TAG_CODE));
        tag_code &= 0xDC;
        if (
               (asc_dvc->pci_fix_asyn_xfer & target_id)
               && !(asc_dvc->pci_fix_asyn_xfer_always & target_id)
) {

            tag_code |= (ASC_TAG_FLAG_DISABLE_DISCONNECT
                         | ASC_TAG_FLAG_DISABLE_ASYN_USE_SYN_FIX);

        }
        AscWriteLramByte(iop_base,
                     (ushort) (halt_q_addr + (ushort) ASC_SCSIQ_B_TAG_CODE),
                         tag_code);

        q_status = AscReadLramByte(iop_base,
                      (ushort) (halt_q_addr + (ushort) ASC_SCSIQ_B_STATUS));
        q_status |= (QS_READY | QS_BUSY);
        AscWriteLramByte(iop_base,
                       (ushort) (halt_q_addr + (ushort) ASC_SCSIQ_B_STATUS),
                         q_status);

        scsi_busy = AscReadLramByte(iop_base,
                                    (ushort) ASCV_SCSIBUSY_B);
        scsi_busy &= ~target_id;
        AscWriteLramByte(iop_base, (ushort) ASCV_SCSIBUSY_B, scsi_busy);

        AscWriteLramWord(iop_base, ASCV_HALTCODE_W, 0);
        return (0);
    } else if (int_halt_code == ASC_HALT_SDTR_REJECTED) {

        AscMemWordCopyFromLram(iop_base,
                               ASCV_MSGOUT_BEG,
                               (ushort *) & out_msg,
                               (ushort) (sizeof (EXT_MSG) >> 1));

        if ((out_msg.msg_type == MS_EXTEND) &&
            (out_msg.msg_len == MS_SDTR_LEN) &&
            (out_msg.msg_req == MS_SDTR_CODE)) {

            asc_dvc->init_sdtr &= ~target_id;
            asc_dvc->sdtr_done &= ~target_id;
            AscSetChipSDTR(iop_base, asyn_sdtr, tid_no);
            boardp->sdtr_data[tid_no] = asyn_sdtr;
        }
        q_cntl &= ~QC_MSG_OUT;
        AscWriteLramByte(iop_base,
                         (ushort) (halt_q_addr + (ushort) ASC_SCSIQ_B_CNTL),
                         q_cntl);
        AscWriteLramWord(iop_base, ASCV_HALTCODE_W, 0);
        return (0);
    } else if (int_halt_code == ASC_HALT_SS_QUEUE_FULL) {

        scsi_status = AscReadLramByte(iop_base,
          (ushort) ((ushort) halt_q_addr + (ushort) ASC_SCSIQ_SCSI_STATUS));
        cur_dvc_qng = AscReadLramByte(iop_base,
                     (ushort) ((ushort) ASC_QADR_BEG + (ushort) target_ix));
        if ((cur_dvc_qng > 0) &&
            (asc_dvc->cur_dvc_qng[tid_no] > 0)) {

            scsi_busy = AscReadLramByte(iop_base,
                                        (ushort) ASCV_SCSIBUSY_B);
            scsi_busy |= target_id;
            AscWriteLramByte(iop_base,
                             (ushort) ASCV_SCSIBUSY_B, scsi_busy);
            asc_dvc->queue_full_or_busy |= target_id;

            if (scsi_status == SS_QUEUE_FULL) {
                if (cur_dvc_qng > ASC_MIN_TAGGED_CMD) {
                    cur_dvc_qng -= 1;
                    asc_dvc->max_dvc_qng[tid_no] = cur_dvc_qng;

                    AscWriteLramByte(iop_base,
                          (ushort) ((ushort) ASCV_MAX_DVC_QNG_BEG +
                           (ushort) tid_no),
                          cur_dvc_qng);

                    /*
                     * Set the device queue depth to the number of
                     * active requests when the QUEUE FULL condition
                     * was encountered.
                     */
                    boardp->queue_full |= target_id;
                    boardp->queue_full_cnt[tid_no] = cur_dvc_qng;
#if ASC_QUEUE_FLOW_CONTROL
                    if (boardp->device[tid_no]->queue_curr_depth >
                        cur_dvc_qng) {
                        boardp->device[tid_no]->queue_curr_depth =
                            cur_dvc_qng;
                    }
#endif /* ASC_QUEUE_FLOW_CONTROL */
                }
            }
        }
        AscWriteLramWord(iop_base, ASCV_HALTCODE_W, 0);
        return (0);
    }
    return (0);
}

STATIC uchar
_AscCopyLramScsiDoneQ(
                         PortAddr iop_base,
                         ushort q_addr,
                         REG ASC_QDONE_INFO * scsiq,
                         ulong max_dma_count
)
{
    ushort              _val;
    uchar               sg_queue_cnt;
    DvcGetQinfo(iop_base,
                (ushort) (q_addr + (ushort) ASC_SCSIQ_DONE_INFO_BEG),
                (ushort *) scsiq,
              (ushort) ((sizeof (ASC_SCSIQ_2) + sizeof (ASC_SCSIQ_3)) / 2));
#if !CC_LITTLE_ENDIAN_HOST
    AscAdjEndianQDoneInfo(scsiq);
#endif
    _val = AscReadLramWord(iop_base,
                           (ushort) (q_addr + (ushort) ASC_SCSIQ_B_STATUS));
    scsiq->q_status = (uchar) _val;
    scsiq->q_no = (uchar) (_val >> 8);
    _val = AscReadLramWord(iop_base,
                           (ushort) (q_addr + (ushort) ASC_SCSIQ_B_CNTL));
    scsiq->cntl = (uchar) _val;
    sg_queue_cnt = (uchar) (_val >> 8);
    _val = AscReadLramWord(iop_base,
                        (ushort) (q_addr + (ushort) ASC_SCSIQ_B_SENSE_LEN));
    scsiq->sense_len = (uchar) _val;
    scsiq->extra_bytes = (uchar) (_val >> 8);
    scsiq->remain_bytes = AscReadLramWord(iop_base,
                 (ushort) (q_addr + (ushort) ASC_SCSIQ_DW_REMAIN_XFER_CNT));
    scsiq->remain_bytes &= max_dma_count;
    return (sg_queue_cnt);
}

STATIC int
AscIsrQDone(
               REG ASC_DVC_VAR asc_ptr_type * asc_dvc
)
{
    uchar               next_qp;
    uchar               n_q_used;
    uchar               sg_list_qp;
    uchar               sg_queue_cnt;
    uchar               q_cnt;
    uchar               done_q_tail;
    uchar               tid_no;
    ASC_SCSI_BIT_ID_TYPE scsi_busy;
    ASC_SCSI_BIT_ID_TYPE target_id;
    PortAddr            iop_base;
    ushort              q_addr;
    ushort              sg_q_addr;
    uchar               cur_target_qng;
    ASC_QDONE_INFO      scsiq_buf;
    REG ASC_QDONE_INFO *scsiq;
    int                 false_overrun;
    ASC_ISR_CALLBACK    asc_isr_callback;
    iop_base = asc_dvc->iop_base;
    asc_isr_callback = (ASC_ISR_CALLBACK) asc_dvc->isr_callback;
    n_q_used = 1;
    scsiq = (ASC_QDONE_INFO *) & scsiq_buf;
    done_q_tail = (uchar) AscGetVarDoneQTail(iop_base);
    q_addr = ASC_QNO_TO_QADDR(done_q_tail);
    next_qp = AscReadLramByte(iop_base,
                              (ushort) (q_addr + (ushort) ASC_SCSIQ_B_FWD));
    if (next_qp != ASC_QLINK_END) {
        AscPutVarDoneQTail(iop_base, next_qp);
        q_addr = ASC_QNO_TO_QADDR(next_qp);
        sg_queue_cnt = _AscCopyLramScsiDoneQ(iop_base, q_addr, scsiq,
            asc_dvc->max_dma_count);
        AscWriteLramByte(iop_base,
                         (ushort) (q_addr + (ushort) ASC_SCSIQ_B_STATUS),
             (uchar) (scsiq->q_status & (uchar) ~ (QS_READY | QS_ABORTED)));
        tid_no = ASC_TIX_TO_TID(scsiq->d2.target_ix);
        target_id = ASC_TIX_TO_TARGET_ID(scsiq->d2.target_ix);
        if ((scsiq->cntl & QC_SG_HEAD) != 0) {
            sg_q_addr = q_addr;
            sg_list_qp = next_qp;
            for (q_cnt = 0; q_cnt < sg_queue_cnt; q_cnt++) {
                sg_list_qp = AscReadLramByte(iop_base,
                           (ushort) (sg_q_addr + (ushort) ASC_SCSIQ_B_FWD));
                sg_q_addr = ASC_QNO_TO_QADDR(sg_list_qp);
                if (sg_list_qp == ASC_QLINK_END) {
                    AscSetLibErrorCode(asc_dvc, ASCQ_ERR_SG_Q_LINKS);
                    scsiq->d3.done_stat = QD_WITH_ERROR;
                    scsiq->d3.host_stat = QHSTA_D_QDONE_SG_LIST_CORRUPTED;
                    goto FATAL_ERR_QDONE;
                }
                AscWriteLramByte(iop_base,
                         (ushort) (sg_q_addr + (ushort) ASC_SCSIQ_B_STATUS),
                                 QS_FREE);
            }
            n_q_used = sg_queue_cnt + 1;
            AscPutVarDoneQTail(iop_base, sg_list_qp);
        }
        if (asc_dvc->queue_full_or_busy & target_id) {
            cur_target_qng = AscReadLramByte(iop_base,
            (ushort) ((ushort) ASC_QADR_BEG + (ushort) scsiq->d2.target_ix));
            if (cur_target_qng < asc_dvc->max_dvc_qng[tid_no]) {
                scsi_busy = AscReadLramByte(iop_base,
                                            (ushort) ASCV_SCSIBUSY_B);
                scsi_busy &= ~target_id;
                AscWriteLramByte(iop_base,
                                 (ushort) ASCV_SCSIBUSY_B, scsi_busy);
                asc_dvc->queue_full_or_busy &= ~target_id;
            }
        }
        if (asc_dvc->cur_total_qng >= n_q_used) {
            asc_dvc->cur_total_qng -= n_q_used;
            if (asc_dvc->cur_dvc_qng[tid_no] != 0) {
                asc_dvc->cur_dvc_qng[tid_no]--;
            }
        } else {
            AscSetLibErrorCode(asc_dvc, ASCQ_ERR_CUR_QNG);
            scsiq->d3.done_stat = QD_WITH_ERROR;
            goto FATAL_ERR_QDONE;
        }
        if ((scsiq->d2.srb_ptr == 0UL) ||
            ((scsiq->q_status & QS_ABORTED) != 0)) {
            return (0x11);
        } else if (scsiq->q_status == QS_DONE) {
            false_overrun = FALSE;
            if (scsiq->extra_bytes != 0) {
                scsiq->remain_bytes += (ulong) scsiq->extra_bytes;
            }
            if (scsiq->d3.done_stat == QD_WITH_ERROR) {
                if (scsiq->d3.host_stat == QHSTA_M_DATA_OVER_RUN) {
                    if ((scsiq->cntl & (QC_DATA_IN | QC_DATA_OUT)) == 0) {
                        scsiq->d3.done_stat = QD_NO_ERROR;
                        scsiq->d3.host_stat = QHSTA_NO_ERROR;
                    } else if (false_overrun) {
                        scsiq->d3.done_stat = QD_NO_ERROR;
                        scsiq->d3.host_stat = QHSTA_NO_ERROR;
                    }
                } else if (scsiq->d3.host_stat ==
                           QHSTA_M_HUNG_REQ_SCSI_BUS_RESET) {
                    AscStopChip(iop_base);
                    AscSetChipControl(iop_base,
                        (uchar) (CC_SCSI_RESET | CC_HALT));
                    DvcDelayNanoSecond(asc_dvc, 30000);
                    AscSetChipControl(iop_base, CC_HALT);
                    AscSetChipStatus(iop_base, CIW_CLR_SCSI_RESET_INT);
                    AscSetChipStatus(iop_base, 0);
                    AscSetChipControl(iop_base, 0);
                }
            }
#if CC_CLEAR_LRAM_SRB_PTR
            AscWriteLramDWord(iop_base,
                            (ushort) (q_addr + (ushort) ASC_SCSIQ_D_SRBPTR),
                              asc_dvc->int_count);
#endif
            if ((scsiq->cntl & QC_NO_CALLBACK) == 0) {
                (*asc_isr_callback) (asc_dvc, scsiq);
            } else {
                if ((AscReadLramByte(iop_base,
                          (ushort) (q_addr + (ushort) ASC_SCSIQ_CDB_BEG)) ==
                     SCSICMD_StartStopUnit)) {
                    asc_dvc->unit_not_ready &= ~target_id;
                    if (scsiq->d3.done_stat != QD_NO_ERROR) {
                        asc_dvc->start_motor &= ~target_id;
                    }
                }
            }
            return (1);
        } else {
            AscSetLibErrorCode(asc_dvc, ASCQ_ERR_Q_STATUS);
          FATAL_ERR_QDONE:
            if ((scsiq->cntl & QC_NO_CALLBACK) == 0) {
                (*asc_isr_callback) (asc_dvc, scsiq);
            }
            return (0x80);
        }
    }
    return (0);
}

STATIC int
AscISR(
          REG ASC_DVC_VAR asc_ptr_type * asc_dvc
)
{
    ASC_CS_TYPE         chipstat;
    PortAddr            iop_base;
    ushort              saved_ram_addr;
    uchar               ctrl_reg;
    uchar               saved_ctrl_reg;
    int                 int_pending;
    int                 status;
    uchar               host_flag;
    iop_base = asc_dvc->iop_base;
    int_pending = FALSE;
    if (((asc_dvc->init_state & ASC_INIT_STATE_END_LOAD_MC) == 0)
        || (asc_dvc->isr_callback == 0)
) {
        return (ERR);
    }
    if (asc_dvc->in_critical_cnt != 0) {
        AscSetLibErrorCode(asc_dvc, ASCQ_ERR_ISR_ON_CRITICAL);
        return (ERR);
    }
    if (asc_dvc->is_in_int) {
        AscSetLibErrorCode(asc_dvc, ASCQ_ERR_ISR_RE_ENTRY);
        return (ERR);
    }
    asc_dvc->is_in_int = TRUE;
    ctrl_reg = AscGetChipControl(iop_base);
    saved_ctrl_reg = ctrl_reg & (~(CC_SCSI_RESET | CC_CHIP_RESET |
                                   CC_SINGLE_STEP | CC_DIAG | CC_TEST));
    chipstat = AscGetChipStatus(iop_base);
    if (chipstat & CSW_SCSI_RESET_LATCH) {
        if (!(asc_dvc->bus_type & (ASC_IS_VL | ASC_IS_EISA))) {
            int_pending = TRUE;
            asc_dvc->sdtr_done = 0;
            saved_ctrl_reg &= (uchar) (~CC_HALT);
            while (AscGetChipStatus(iop_base) & CSW_SCSI_RESET_ACTIVE) ;
            AscSetChipControl(iop_base, (CC_CHIP_RESET | CC_HALT));
            AscSetChipControl(iop_base, CC_HALT);
            AscSetChipStatus(iop_base, CIW_CLR_SCSI_RESET_INT);
            AscSetChipStatus(iop_base, 0);
            chipstat = AscGetChipStatus(iop_base);
        }
    }
    saved_ram_addr = AscGetChipLramAddr(iop_base);
    host_flag = AscReadLramByte(iop_base,
        ASCV_HOST_FLAG_B) & (uchar) (~ASC_HOST_FLAG_IN_ISR);
    AscWriteLramByte(iop_base, ASCV_HOST_FLAG_B,
                     (uchar) (host_flag | (uchar) ASC_HOST_FLAG_IN_ISR));
#if CC_ASCISR_CHECK_INT_PENDING
    if ((chipstat & CSW_INT_PENDING)
        || (int_pending)
) {
        AscAckInterrupt(iop_base);
#endif
        int_pending = TRUE;
        if ((chipstat & CSW_HALTED) &&
            (ctrl_reg & CC_SINGLE_STEP)) {
            if (AscIsrChipHalted(asc_dvc) == ERR) {
                goto ISR_REPORT_QDONE_FATAL_ERROR;
            } else {
                saved_ctrl_reg &= (uchar) (~CC_HALT);
            }
        } else {
          ISR_REPORT_QDONE_FATAL_ERROR:
            if ((asc_dvc->dvc_cntl & ASC_CNTL_INT_MULTI_Q) != 0) {
                while (((status = AscIsrQDone(asc_dvc)) & 0x01) != 0) {
                }
            } else {
                do {
                    if ((status = AscIsrQDone(asc_dvc)) == 1) {
                        break;
                    }
                } while (status == 0x11);
            }
            if ((status & 0x80) != 0)
                int_pending = ERR;
        }
#if CC_ASCISR_CHECK_INT_PENDING
    }
#endif
    AscWriteLramByte(iop_base, ASCV_HOST_FLAG_B, host_flag);
    AscSetChipLramAddr(iop_base, saved_ram_addr);
    AscSetChipControl(iop_base, saved_ctrl_reg);
    asc_dvc->is_in_int = FALSE;
    return (int_pending);
}

STATIC int
AscScsiSetupCmdQ(
                    REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                    REG ASC_SCSI_REQ_Q * scsiq,
                    uchar * buf_addr,
                    ulong buf_len
)
{
    ulong               phy_addr;
    scsiq->r1.cntl = 0;
    scsiq->r1.sg_queue_cnt = 0;
    scsiq->r1.q_no = 0;
    scsiq->r1.extra_bytes = 0;
    scsiq->r3.scsi_stat = 0;
    scsiq->r3.scsi_msg = 0;
    scsiq->r3.host_stat = 0;
    scsiq->r3.done_stat = 0;
    scsiq->r2.vm_id = 0;
    scsiq->r1.data_cnt = buf_len;
    scsiq->cdbptr = (uchar *) scsiq->cdb;
    scsiq->sense_ptr = (uchar *) scsiq->sense ;
    scsiq->r1.sense_len = ASC_MIN_SENSE_LEN ;
    scsiq->r2.tag_code = (uchar) M2_QTAG_MSG_SIMPLE;
    scsiq->r2.flag = (uchar) ASC_FLAG_SCSIQ_REQ;
    scsiq->r2.srb_ptr = (ulong) scsiq;
    scsiq->r1.status = (uchar) QS_READY;
    scsiq->r1.data_addr = 0L;
    if (buf_len != 0L) {
        if ((phy_addr = AscGetOnePhyAddr(asc_dvc,
                    (uchar *) buf_addr, scsiq->r1.data_cnt)) == 0L) {
            return (ERR);
        }
        scsiq->r1.data_addr = phy_addr;
    }
    if ((phy_addr = AscGetOnePhyAddr(asc_dvc,
                       (uchar *) scsiq->sense_ptr,
                       (ulong) scsiq->r1.sense_len)) == 0L) {
        return (ERR);
    }
    scsiq->r1.sense_addr = phy_addr ;
    return (0);
}

STATIC uchar _mcode_buf[] ASC_INITDATA =
{
    0x01, 0x03, 0x01, 0x19, 0x0F, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
    0x0F, 0x0F, 0x0F, 0x0F, 0x0F, 0x0F, 0x0F, 0x0F, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
    0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
    0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
    0x00, 0x00, 0x00, 0x00, 0x79, 0x0D, 0x09, 0x05, 0x01, 0x00, 0x00, 0x00, 0x00, 0xFF, 0x00, 0x00,
    0x00, 0x00, 0x00, 0x00, 0xFF, 0x80, 0xFF, 0xFF, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
    0x00, 0x00, 0x00, 0x23, 0x00, 0x22, 0x00, 0x00, 0x00, 0x07, 0x00, 0xFF, 0x00, 0x00, 0x00, 0x00,
    0xFF, 0xFF, 0xFF, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xCC, 0x88, 0x00, 0x00, 0x00, 0x00,
    0x80, 0x73, 0x48, 0x04, 0x36, 0x00, 0x00, 0xA2, 0xC2, 0x00, 0x80, 0x73, 0x03, 0x23, 0x36, 0x40,
    0xB6, 0x00, 0x36, 0x00, 0x05, 0xD6, 0x0C, 0xD2, 0x12, 0xDA, 0x00, 0xA2, 0xC2, 0x00, 0x92, 0x80,
    0x08, 0x98, 0x50, 0x00, 0xF5, 0x00, 0x32, 0x98, 0xDF, 0x23, 0x36, 0x60, 0xB6, 0x00, 0x92, 0x80,
    0x4F, 0x00, 0xF5, 0x00, 0x32, 0x98, 0xEF, 0x23, 0x36, 0x60, 0xB6, 0x00, 0x92, 0x80, 0x80, 0x62,
    0x92, 0x80, 0x00, 0x46, 0x17, 0xEE, 0x13, 0xEA, 0x02, 0x01, 0x09, 0xD8, 0xCD, 0x04, 0x4D, 0x00,
    0x00, 0xA3, 0xD6, 0x00, 0x90, 0x97, 0x7F, 0x23, 0x04, 0x61, 0x84, 0x01, 0xD8, 0x84, 0xD2, 0xC1,
    0x80, 0x73, 0xCD, 0x04, 0x4D, 0x00, 0x00, 0xA3, 0xE2, 0x01, 0x90, 0x97, 0xCE, 0x81, 0x00, 0x33,
    0x02, 0x00, 0xAA, 0x88, 0x80, 0x73, 0x80, 0x77, 0x00, 0x01, 0x01, 0xA1, 0x02, 0x01, 0x4F, 0x00,
    0x6E, 0x97, 0x07, 0xA6, 0x0C, 0x01, 0x00, 0x33, 0x03, 0x00, 0xAA, 0x88, 0x03, 0x03, 0x03, 0xDE,
    0x00, 0x33, 0x05, 0x00, 0xAA, 0x88, 0xCE, 0x00, 0x69, 0x60, 0xCE, 0x00, 0x02, 0x03, 0x4A, 0x60,
    0x00, 0xA2, 0x80, 0x01, 0x80, 0x63, 0x07, 0xA6, 0x2C, 0x01, 0x80, 0x81, 0x03, 0x03, 0x80, 0x63,
    0xE2, 0x00, 0x07, 0xA6, 0x3C, 0x01, 0x00, 0x33, 0x04, 0x00, 0xAA, 0x88, 0x03, 0x07, 0x02, 0x01,
    0x04, 0xCA, 0x0D, 0x23, 0x52, 0x98, 0x4D, 0x04, 0xF6, 0x84, 0x05, 0xD8, 0x0D, 0x23, 0x52, 0x98,
    0xCD, 0x04, 0x15, 0x23, 0xE0, 0x88, 0xFB, 0x23, 0x02, 0x61, 0x82, 0x01, 0x80, 0x63, 0x02, 0x03,
    0x06, 0xA3, 0x6A, 0x01, 0x00, 0x33, 0x0A, 0x00, 0xAA, 0x88, 0x4E, 0x00, 0x07, 0xA3, 0x76, 0x01,
    0x00, 0x33, 0x0B, 0x00, 0xAA, 0x88, 0xCD, 0x04, 0x36, 0x2D, 0x00, 0x33, 0x1A, 0x00, 0xAA, 0x88,
    0x50, 0x04, 0x90, 0x81, 0x06, 0xAB, 0x8A, 0x01, 0x90, 0x81, 0x4E, 0x00, 0x07, 0xA3, 0x9A, 0x01,
    0x50, 0x00, 0x00, 0xA3, 0x44, 0x01, 0x00, 0x05, 0x84, 0x81, 0x30, 0x97, 0x02, 0x01, 0x05, 0xC6,
    0x04, 0x23, 0xA0, 0x01, 0x15, 0x23, 0xA1, 0x01, 0xC6, 0x81, 0xFD, 0x23, 0x02, 0x61, 0x82, 0x01,
    0x0A, 0xDA, 0x4A, 0x00, 0x06, 0x61, 0x00, 0xA0, 0xBC, 0x01, 0x80, 0x63, 0xCD, 0x04, 0x36, 0x2D,
    0x00, 0x33, 0x1B, 0x00, 0xAA, 0x88, 0x06, 0x23, 0x52, 0x98, 0xCD, 0x04, 0xD8, 0x84, 0x06, 0x01,
    0x00, 0xA2, 0xDC, 0x01, 0x57, 0x60, 0x00, 0xA0, 0xE2, 0x01, 0xD8, 0x84, 0x80, 0x23, 0xA0, 0x01,
    0xD8, 0x84, 0x80, 0x73, 0x4B, 0x00, 0x06, 0x61, 0x00, 0xA2, 0x08, 0x02, 0x04, 0x01, 0x0C, 0xDE,
    0x02, 0x01, 0x03, 0xCC, 0x4F, 0x00, 0x6E, 0x97, 0x04, 0x82, 0x08, 0x23, 0x02, 0x41, 0x82, 0x01,
    0x4F, 0x00, 0x4C, 0x97, 0x48, 0x04, 0x84, 0x80, 0xDA, 0x97, 0x00, 0x46, 0x56, 0x00, 0x03, 0xC0,
    0x01, 0x23, 0xE8, 0x00, 0x81, 0x73, 0x06, 0x29, 0x03, 0x42, 0x06, 0xE2, 0x03, 0xEE, 0x67, 0xEB,
    0x11, 0x23, 0xE0, 0x88, 0xEE, 0x97, 0xF4, 0x80, 0x80, 0x73, 0x80, 0x77, 0x06, 0xA6, 0x36, 0x02,
    0x00, 0x33, 0x31, 0x00, 0xAA, 0x88, 0x04, 0x01, 0x03, 0xD8, 0x9C, 0x98, 0x44, 0x96, 0x48, 0x82,
    0xD4, 0x95, 0x80, 0x67, 0x83, 0x03, 0x80, 0x63, 0xB6, 0x2D, 0x02, 0xA6, 0x72, 0x02, 0x07, 0xA6,
    0x60, 0x02, 0x06, 0xA6, 0x64, 0x02, 0x03, 0xA6, 0x68, 0x02, 0x00, 0x33, 0x10, 0x00, 0xAA, 0x88,
    0x6E, 0x95, 0x4A, 0x82, 0x3A, 0x96, 0x4A, 0x82, 0x04, 0x23, 0xA0, 0x01, 0x14, 0x23, 0xA1, 0x01,
    0x2E, 0x84, 0x04, 0x01, 0x0C, 0xDC, 0xE0, 0x23, 0x25, 0x61, 0xEF, 0x00, 0x14, 0x01, 0x4F, 0x04,
    0xA8, 0x01, 0x6F, 0x00, 0xA5, 0x01, 0x03, 0x23, 0xA4, 0x01, 0x06, 0x23, 0x9C, 0x01, 0x24, 0x2B,
    0x1C, 0x01, 0x02, 0xA6, 0xB0, 0x02, 0x07, 0xA6, 0x60, 0x02, 0x06, 0xA6, 0x64, 0x02, 0x03, 0xA6,
    0x12, 0x04, 0x01, 0xA6, 0xBA, 0x02, 0x00, 0xA6, 0xBA, 0x02, 0x00, 0x33, 0x12, 0x00, 0xAA, 0x88,
    0x00, 0x0E, 0x80, 0x63, 0x00, 0x43, 0x00, 0xA0, 0x92, 0x02, 0x4D, 0x04, 0x04, 0x01, 0x0B, 0xDC,
    0xE7, 0x23, 0x04, 0x61, 0x84, 0x01, 0x10, 0x31, 0x12, 0x35, 0x14, 0x01, 0xEC, 0x00, 0x6C, 0x38,
    0x00, 0x3F, 0x00, 0x00, 0xF0, 0x82, 0x18, 0x23, 0x04, 0x61, 0x18, 0xA0, 0xE8, 0x02, 0x04, 0x01,
    0x98, 0xC8, 0x00, 0x33, 0x1F, 0x00, 0xAA, 0x88, 0x08, 0x31, 0x0A, 0x35, 0x0C, 0x39, 0x0E, 0x3D,
    0x68, 0x98, 0xB6, 0x2D, 0x01, 0xA6, 0x1A, 0x03, 0x00, 0xA6, 0x1A, 0x03, 0x07, 0xA6, 0x12, 0x03,
    0x06, 0xA6, 0x16, 0x03, 0x03, 0xA6, 0x12, 0x04, 0x02, 0xA6, 0x72, 0x02, 0x00, 0x33, 0x33, 0x00,
    0xAA, 0x88, 0x6E, 0x95, 0xF4, 0x82, 0x3A, 0x96, 0xF4, 0x82, 0x6C, 0x98, 0x80, 0x42, 0x68, 0x98,
    0x60, 0xE4, 0x04, 0x01, 0x29, 0xC8, 0x31, 0x05, 0x07, 0x01, 0x00, 0xA2, 0x5A, 0x03, 0x00, 0x43,
    0x87, 0x01, 0x05, 0x05, 0x70, 0x98, 0x68, 0x98, 0x00, 0xA6, 0x1C, 0x03, 0x07, 0xA6, 0x52, 0x03,
    0x03, 0xA6, 0x2E, 0x04, 0x06, 0xA6, 0x56, 0x03, 0x01, 0xA6, 0x1C, 0x03, 0x00, 0x33, 0x25, 0x00,
    0xAA, 0x88, 0x6E, 0x95, 0x38, 0x83, 0x3A, 0x96, 0x38, 0x83, 0x04, 0x01, 0x0C, 0xCE, 0x03, 0xC8,
    0x00, 0x33, 0x42, 0x00, 0xAA, 0x88, 0x00, 0x01, 0x05, 0x05, 0xFF, 0xA2, 0x78, 0x03, 0xB1, 0x01,
    0x08, 0x23, 0xB2, 0x01, 0x34, 0x83, 0x05, 0x05, 0x15, 0x01, 0x00, 0xA2, 0x98, 0x03, 0xEC, 0x00,
    0x6E, 0x00, 0x95, 0x01, 0x6C, 0x38, 0x00, 0x3F, 0x00, 0x00, 0x01, 0xA6, 0x94, 0x03, 0x00, 0xA6,
    0x94, 0x03, 0x08, 0x84, 0x80, 0x42, 0x68, 0x98, 0x01, 0xA6, 0xA2, 0x03, 0x00, 0xA6, 0xBA, 0x03,
    0x08, 0x84, 0x90, 0x98, 0x80, 0x42, 0x01, 0xA6, 0xA2, 0x03, 0x07, 0xA6, 0xB0, 0x03, 0xD2, 0x83,
    0x6E, 0x95, 0xA6, 0x83, 0x00, 0x33, 0x2F, 0x00, 0xAA, 0x88, 0x90, 0x98, 0x80, 0x42, 0x00, 0xA6,
    0xBA, 0x03, 0x07, 0xA6, 0xC8, 0x03, 0xD2, 0x83, 0x6E, 0x95, 0xBE, 0x83, 0x00, 0x33, 0x26, 0x00,
    0xAA, 0x88, 0x38, 0x2B, 0x80, 0x32, 0x80, 0x36, 0x04, 0x23, 0xA0, 0x01, 0x12, 0x23, 0xA1, 0x01,
    0x08, 0x84, 0x04, 0xF0, 0x80, 0x6B, 0x00, 0x33, 0x20, 0x00, 0xAA, 0x88, 0x03, 0xA6, 0x06, 0x04,
    0x07, 0xA6, 0xFE, 0x03, 0x06, 0xA6, 0x02, 0x04, 0x00, 0x33, 0x17, 0x00, 0xAA, 0x88, 0x6E, 0x95,
    0xEC, 0x83, 0x3A, 0x96, 0xEC, 0x83, 0x12, 0x84, 0x04, 0xF0, 0x80, 0x6B, 0x00, 0x33, 0x20, 0x00,
    0xAA, 0x88, 0xB6, 0x2D, 0x03, 0xA6, 0x2E, 0x04, 0x07, 0xA6, 0x26, 0x04, 0x06, 0xA6, 0x2A, 0x04,
    0x00, 0x33, 0x30, 0x00, 0xAA, 0x88, 0x6E, 0x95, 0x12, 0x84, 0x3A, 0x96, 0x12, 0x84, 0x1D, 0x01,
    0x06, 0xCC, 0x00, 0x33, 0x00, 0x84, 0xC0, 0x20, 0x00, 0x23, 0xEA, 0x00, 0x81, 0x62, 0xA2, 0x0D,
    0x80, 0x63, 0x07, 0xA6, 0x4C, 0x04, 0x00, 0x33, 0x18, 0x00, 0xAA, 0x88, 0x03, 0x03, 0x80, 0x63,
    0xA3, 0x01, 0x07, 0xA4, 0x56, 0x04, 0x23, 0x01, 0x00, 0xA2, 0x78, 0x04, 0x0A, 0xA0, 0x68, 0x04,
    0xE0, 0x00, 0x00, 0x33, 0x1D, 0x00, 0xAA, 0x88, 0x0B, 0xA0, 0x74, 0x04, 0xE0, 0x00, 0x00, 0x33,
    0x1E, 0x00, 0xAA, 0x88, 0x42, 0x23, 0xE0, 0x88, 0x00, 0x23, 0x22, 0xA3, 0xD8, 0x04, 0x08, 0x23,
    0x22, 0xA3, 0x94, 0x04, 0x28, 0x23, 0x22, 0xA3, 0xA0, 0x04, 0x02, 0x23, 0x22, 0xA3, 0xB6, 0x04,
    0x42, 0x23, 0xE0, 0x88, 0x4A, 0x00, 0x06, 0x61, 0x00, 0xA0, 0xA0, 0x04, 0x45, 0x23, 0xE0, 0x88,
    0xEE, 0x97, 0x00, 0xA2, 0xB2, 0x04, 0x9C, 0x98, 0x00, 0x33, 0x00, 0x82, 0xC0, 0x20, 0x81, 0x62,
    0xF0, 0x81, 0x47, 0x23, 0xE0, 0x88, 0x04, 0x01, 0x0B, 0xDE, 0xEE, 0x97, 0x9C, 0x98, 0x00, 0x33,
    0x00, 0x81, 0xC0, 0x20, 0x81, 0x62, 0x14, 0x01, 0x00, 0xA0, 0x08, 0x02, 0x43, 0x23, 0xE0, 0x88,
    0x04, 0x23, 0xA0, 0x01, 0x44, 0x23, 0xA1, 0x01, 0x80, 0x73, 0x4D, 0x00, 0x03, 0xA3, 0xE6, 0x04,
    0x00, 0x33, 0x27, 0x00, 0xAA, 0x88, 0x04, 0x01, 0x04, 0xDC, 0x02, 0x23, 0xA2, 0x01, 0x04, 0x23,
    0xA0, 0x01, 0xEE, 0x97, 0x18, 0x95, 0x4B, 0x00, 0xF6, 0x00, 0x4F, 0x04, 0x4F, 0x00, 0x00, 0xA3,
    0x14, 0x05, 0x00, 0x05, 0x76, 0x00, 0x06, 0x61, 0x00, 0xA2, 0x0E, 0x05, 0xFC, 0x84, 0x30, 0x97,
    0xCD, 0x04, 0x16, 0x85, 0x48, 0x04, 0x84, 0x80, 0x02, 0x01, 0x03, 0xDA, 0x80, 0x23, 0x82, 0x01,
    0x26, 0x85, 0x02, 0x23, 0xA0, 0x01, 0x4A, 0x00, 0x06, 0x61, 0x00, 0xA2, 0x32, 0x05, 0x1D, 0x01,
    0x04, 0xD6, 0xFF, 0x23, 0x86, 0x41, 0x4B, 0x60, 0xCB, 0x00, 0xFF, 0x23, 0x80, 0x01, 0x49, 0x00,
    0x81, 0x01, 0x04, 0x01, 0x02, 0xC8, 0x30, 0x01, 0x80, 0x01, 0xF7, 0x04, 0x03, 0x01, 0x49, 0x04,
    0x80, 0x01, 0xC9, 0x00, 0x00, 0x05, 0x00, 0x01, 0xFF, 0xA0, 0x52, 0x05, 0x77, 0x04, 0x01, 0x23,
    0xEA, 0x00, 0x5D, 0x00, 0xFE, 0xC7, 0x00, 0x62, 0x00, 0x23, 0xEA, 0x00, 0x00, 0x63, 0x07, 0xA4,
    0xD2, 0x05, 0x03, 0x03, 0x02, 0xA0, 0x80, 0x05, 0xCE, 0x85, 0x00, 0x33, 0x2D, 0x00, 0xAA, 0x88,
    0x04, 0xA0, 0xA6, 0x05, 0x80, 0x63, 0x4A, 0x00, 0x06, 0x61, 0x00, 0xA2, 0x92, 0x05, 0x1D, 0x01,
    0x06, 0xD6, 0x02, 0x23, 0x02, 0x41, 0x82, 0x01, 0x50, 0x00, 0x4C, 0x97, 0xF6, 0x84, 0x04, 0x23,
    0x02, 0x41, 0x82, 0x01, 0xF6, 0x84, 0x08, 0xA0, 0xAC, 0x05, 0xCE, 0x85, 0x03, 0xA0, 0xB2, 0x05,
    0xCE, 0x85, 0x01, 0xA0, 0xBC, 0x05, 0x88, 0x00, 0x80, 0x63, 0xAA, 0x86, 0x07, 0xA0, 0xC8, 0x05,
    0x06, 0x23, 0x52, 0x98, 0x48, 0x23, 0xE0, 0x88, 0x07, 0x23, 0x80, 0x00, 0xF0, 0x86, 0x80, 0x63,
    0x6E, 0x85, 0x00, 0x63, 0x4A, 0x00, 0x06, 0x61, 0x00, 0xA2, 0x10, 0x06, 0x1D, 0x01, 0x18, 0xD4,
    0xC0, 0x23, 0x07, 0x41, 0x83, 0x03, 0x80, 0x63, 0x06, 0xA6, 0xF2, 0x05, 0x00, 0x33, 0x37, 0x00,
    0xAA, 0x88, 0x1D, 0x01, 0x02, 0xD6, 0x46, 0x23, 0xE0, 0x88, 0x63, 0x60, 0x83, 0x03, 0x80, 0x63,
    0x06, 0xA6, 0x0A, 0x06, 0x00, 0x33, 0x38, 0x00, 0xAA, 0x88, 0xEF, 0x04, 0x6F, 0x00, 0x00, 0x63,
    0x4B, 0x00, 0x06, 0x41, 0xCB, 0x00, 0x52, 0x00, 0x06, 0x61, 0x00, 0xA2, 0x28, 0x06, 0x1D, 0x01,
    0x03, 0xCA, 0xC0, 0x23, 0x07, 0x41, 0x00, 0x63, 0x1D, 0x01, 0x04, 0xCC, 0x00, 0x33, 0x00, 0x83,
    0xC0, 0x20, 0x81, 0x62, 0x80, 0x23, 0x07, 0x41, 0x00, 0x63, 0x80, 0x67, 0x08, 0x23, 0x83, 0x03,
    0x80, 0x63, 0x00, 0x63, 0x06, 0xA6, 0x56, 0x06, 0x07, 0xA6, 0x6E, 0x05, 0x02, 0xA6, 0xE4, 0x06,
    0x00, 0x33, 0x39, 0x00, 0xAA, 0x88, 0x00, 0x00, 0x01, 0xA0, 0xFE, 0x06, 0xD4, 0x95, 0x83, 0x03,
    0x80, 0x63, 0x06, 0xA6, 0x6A, 0x06, 0x07, 0xA6, 0x6E, 0x05, 0x00, 0x00, 0x01, 0xA0, 0xFE, 0x06,
    0x00, 0x2B, 0x40, 0x0E, 0x80, 0x63, 0x01, 0x00, 0x06, 0xA6, 0x86, 0x06, 0x07, 0xA6, 0x6E, 0x05,
    0x00, 0x33, 0x3A, 0x00, 0xAA, 0x88, 0x40, 0x0E, 0x80, 0x63, 0x00, 0x43, 0x00, 0xA0, 0x78, 0x06,
    0x06, 0xA6, 0x9E, 0x06, 0x07, 0xA6, 0x6E, 0x05, 0x00, 0x33, 0x3B, 0x00, 0xAA, 0x88, 0x80, 0x67,
    0x40, 0x0E, 0x80, 0x63, 0x07, 0xA6, 0x6E, 0x05, 0x00, 0x63, 0x07, 0xA6, 0xB4, 0x06, 0x00, 0x33,
    0x2A, 0x00, 0xAA, 0x88, 0x03, 0x03, 0x80, 0x63, 0x89, 0x00, 0x0A, 0x2B, 0x07, 0xA6, 0xC6, 0x06,
    0x00, 0x33, 0x29, 0x00, 0xAA, 0x88, 0x00, 0x43, 0x00, 0xA2, 0xD2, 0x06, 0xC0, 0x0E, 0x80, 0x63,
    0xBC, 0x86, 0xC0, 0x0E, 0x00, 0x33, 0x00, 0x80, 0xC0, 0x20, 0x81, 0x62, 0x04, 0x01, 0x08, 0xDA,
    0x80, 0x63, 0x6E, 0x85, 0x80, 0x67, 0x00, 0x33, 0x00, 0x40, 0xC0, 0x20, 0x81, 0x62, 0x00, 0x63,
    0x80, 0x7B, 0x80, 0x63, 0x06, 0xA6, 0x62, 0x06, 0x00, 0x33, 0x2C, 0x00, 0xAA, 0x88, 0x0C, 0xA2,
    0x18, 0x07, 0xD4, 0x95, 0x83, 0x03, 0x80, 0x63, 0x06, 0xA6, 0x16, 0x07, 0x07, 0xA6, 0x6E, 0x05,
    0x00, 0x33, 0x3D, 0x00, 0xAA, 0x88, 0x00, 0x00, 0x80, 0x67, 0x83, 0x03, 0x80, 0x63, 0x0C, 0xA0,
    0x2E, 0x07, 0x07, 0xA6, 0x6E, 0x05, 0xBF, 0x23, 0x04, 0x61, 0x84, 0x01, 0xD8, 0x84, 0x00, 0x63,
    0xF0, 0x04, 0x01, 0x01, 0xF1, 0x00, 0x00, 0x01, 0xF2, 0x00, 0x01, 0x05, 0x80, 0x01, 0x72, 0x04,
    0x71, 0x00, 0x81, 0x01, 0x70, 0x04, 0x80, 0x05, 0x81, 0x05, 0x00, 0x63, 0xF0, 0x04, 0xF2, 0x00,
    0x72, 0x04, 0x01, 0x01, 0xF1, 0x00, 0x70, 0x00, 0x81, 0x01, 0x70, 0x04, 0x71, 0x00, 0x81, 0x01,
    0x72, 0x00, 0x80, 0x01, 0x71, 0x04, 0x70, 0x00, 0x80, 0x01, 0x70, 0x04, 0x00, 0x63, 0xF0, 0x04,
    0xF2, 0x00, 0x72, 0x04, 0x00, 0x01, 0xF1, 0x00, 0x70, 0x00, 0x80, 0x01, 0x70, 0x04, 0x71, 0x00,
    0x80, 0x01, 0x72, 0x00, 0x81, 0x01, 0x71, 0x04, 0x70, 0x00, 0x81, 0x01, 0x70, 0x04, 0x00, 0x63,
    0x00, 0x23, 0xB3, 0x01, 0x83, 0x05, 0xA3, 0x01, 0xA2, 0x01, 0xA1, 0x01, 0x01, 0x23, 0xA0, 0x01,
    0x00, 0x01, 0xC8, 0x00, 0x03, 0xA1, 0xAE, 0x07, 0x00, 0x33, 0x07, 0x00, 0xAA, 0x88, 0x80, 0x05,
    0x81, 0x05, 0x04, 0x01, 0x11, 0xC8, 0x48, 0x00, 0xB0, 0x01, 0xB1, 0x01, 0x08, 0x23, 0xB2, 0x01,
    0x05, 0x01, 0x48, 0x04, 0x00, 0x43, 0x00, 0xA2, 0xCE, 0x07, 0x00, 0x05, 0xC4, 0x87, 0x00, 0x01,
    0xC8, 0x00, 0xFF, 0x23, 0x80, 0x01, 0x05, 0x05, 0x00, 0x63, 0xF7, 0x04, 0x1A, 0x09, 0xF6, 0x08,
    0x6E, 0x04, 0x00, 0x02, 0x80, 0x43, 0x76, 0x08, 0x80, 0x02, 0x77, 0x04, 0x00, 0x63, 0xF7, 0x04,
    0x1A, 0x09, 0xF6, 0x08, 0x6E, 0x04, 0x00, 0x02, 0x00, 0xA0, 0xFE, 0x07, 0x00, 0x88, 0x00, 0x43,
    0x76, 0x08, 0x80, 0x02, 0x77, 0x04, 0x00, 0x63, 0xF3, 0x04, 0x00, 0x23, 0xF4, 0x00, 0x74, 0x00,
    0x80, 0x43, 0xF4, 0x00, 0xCF, 0x40, 0x00, 0xA2, 0x2E, 0x08, 0x74, 0x04, 0x02, 0x01, 0xF7, 0xC9,
    0xF6, 0xD9, 0x00, 0x01, 0x01, 0xA1, 0x0E, 0x08, 0xEE, 0x97, 0x18, 0x95, 0x0E, 0x88, 0x73, 0x04,
    0x00, 0x63, 0xF3, 0x04, 0x75, 0x04, 0x44, 0x88, 0x02, 0x01, 0x04, 0xD8, 0x30, 0x97, 0xEE, 0x97,
    0x18, 0x95, 0x34, 0x88, 0x75, 0x00, 0x00, 0xA3, 0x4E, 0x08, 0x00, 0x05, 0x38, 0x88, 0x73, 0x04,
    0x00, 0x63, 0x80, 0x7B, 0x80, 0x63, 0x06, 0xA6, 0x60, 0x08, 0x00, 0x33, 0x3E, 0x00, 0xAA, 0x88,
    0x80, 0x67, 0x83, 0x03, 0x80, 0x63, 0x00, 0x63, 0x38, 0x2B, 0x86, 0x88, 0x38, 0x2B, 0x7C, 0x88,
    0x32, 0x09, 0x31, 0x05, 0x7C, 0x98, 0x05, 0x05, 0xB2, 0x09, 0x00, 0x63, 0x00, 0x32, 0x00, 0x36,
    0x00, 0x3A, 0x00, 0x3E, 0x00, 0x63, 0x80, 0x32, 0x80, 0x36, 0x80, 0x3A, 0x80, 0x3E, 0x00, 0x63,
    0x38, 0x2B, 0x40, 0x32, 0x40, 0x36, 0x40, 0x3A, 0x40, 0x3E, 0x00, 0x63, 0x5A, 0x20, 0xC9, 0x40,
    0x00, 0xA0, 0x9C, 0x08, 0x5D, 0x00, 0xFE, 0xC3, 0x00, 0x63, 0x80, 0x73, 0xE6, 0x20, 0x02, 0x23,
    0xE8, 0x00, 0x82, 0x73, 0xFF, 0xFD, 0x80, 0x73, 0x13, 0x23, 0xE0, 0x88, 0x66, 0x20, 0xC0, 0x20,
    0x04, 0x23, 0xA0, 0x01, 0xA1, 0x23, 0xA1, 0x01, 0x81, 0x62, 0xCA, 0x88, 0x80, 0x73, 0x80, 0x77,
    0x68, 0x00, 0x00, 0xA2, 0x80, 0x00, 0x03, 0xC2, 0xF1, 0xC7, 0x41, 0x23, 0xE0, 0x88, 0x11, 0x23,
    0xA1, 0x01, 0x04, 0x23, 0xA0, 0x01, 0xD8, 0x84,
};

STATIC ushort _mcode_size ASC_INITDATA = sizeof(_mcode_buf);
STATIC ulong _mcode_chksum ASC_INITDATA = 0x01297F32UL;

#define ASC_SYN_OFFSET_ONE_DISABLE_LIST  16
STATIC uchar _syn_offset_one_disable_cmd[ASC_SYN_OFFSET_ONE_DISABLE_LIST] =
{
    SCSICMD_Inquiry,
    SCSICMD_RequestSense,
    SCSICMD_ReadCapacity,
    SCSICMD_ReadTOC,
    SCSICMD_ModeSelect6,
    SCSICMD_ModeSense6,
    SCSICMD_ModeSelect10,
    SCSICMD_ModeSense10,
    0xFF,
    0xFF,
    0xFF,
    0xFF,
    0xFF,
    0xFF,
    0xFF,
    0xFF
};

STATIC int
AscExeScsiQueue(
                   REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                   REG ASC_SCSI_Q * scsiq
)
{
    PortAddr            iop_base;
    int                 last_int_level;
    int                 sta;
    int                 n_q_required;
    int                 disable_syn_offset_one_fix;
    int                 i;
    ulong               addr;
    ASC_EXE_CALLBACK    asc_exe_callback;
    ushort              sg_entry_cnt = 0;
    ushort              sg_entry_cnt_minus_one = 0;
    uchar               target_ix;
    uchar               tid_no;
    uchar               sdtr_data;
    uchar               extra_bytes;
    uchar               scsi_cmd;
    uchar               disable_cmd;
    ASC_SG_HEAD *sg_head;
    ulong               data_cnt;
    iop_base = asc_dvc->iop_base;
    sg_head = scsiq->sg_head;
    asc_exe_callback = (ASC_EXE_CALLBACK) asc_dvc->exe_callback;
    if (asc_dvc->err_code != 0)
        return (ERR);
    if (scsiq == (ASC_SCSI_Q *) 0L) {
        AscSetLibErrorCode(asc_dvc, ASCQ_ERR_SCSIQ_NULL_PTR);
        return (ERR);
    }
    scsiq->q1.q_no = 0;
    if ((scsiq->q2.tag_code & ASC_TAG_FLAG_EXTRA_BYTES) == 0) {
        scsiq->q1.extra_bytes = 0;
    }
    sta = 0;
    target_ix = scsiq->q2.target_ix;
    tid_no = ASC_TIX_TO_TID(target_ix);
    n_q_required = 1;
    if (scsiq->cdbptr[0] == SCSICMD_RequestSense) {
        if ((asc_dvc->init_sdtr & scsiq->q1.target_id) != 0) {
            asc_dvc->sdtr_done &= ~scsiq->q1.target_id ;
            sdtr_data = AscGetMCodeInitSDTRAtID(iop_base, tid_no);
            AscMsgOutSDTR(asc_dvc,
                          asc_dvc->sdtr_period_tbl[(sdtr_data >> 4) &
                          (uchar) (asc_dvc->max_sdtr_index - 1)],
                          (uchar) (sdtr_data & (uchar) ASC_SYN_MAX_OFFSET));
            scsiq->q1.cntl |= (QC_MSG_OUT | QC_URGENT);
        }
    }
    last_int_level = DvcEnterCritical();
    if (asc_dvc->in_critical_cnt != 0) {
        DvcLeaveCritical(last_int_level);
        AscSetLibErrorCode(asc_dvc, ASCQ_ERR_CRITICAL_RE_ENTRY);
        return (ERR);
    }
    asc_dvc->in_critical_cnt++;
    if ((scsiq->q1.cntl & QC_SG_HEAD) != 0) {
        if ((sg_entry_cnt = sg_head->entry_cnt) == 0) {
            asc_dvc->in_critical_cnt--;
            DvcLeaveCritical(last_int_level);
            return (ERR);
        }
        if (sg_entry_cnt > ASC_MAX_SG_LIST) {
            return (ERR);
        }
        if (sg_entry_cnt == 1) {
            scsiq->q1.data_addr = sg_head->sg_list[0].addr;
            scsiq->q1.data_cnt = sg_head->sg_list[0].bytes;
            scsiq->q1.cntl &= ~(QC_SG_HEAD | QC_SG_SWAP_QUEUE);
        }
        sg_entry_cnt_minus_one = sg_entry_cnt - 1;
#if CC_DEBUG_SG_LIST
        if (asc_dvc->bus_type & (ASC_IS_ISA | ASC_IS_VL | ASC_IS_EISA)) {
            for (i = 0; i < sg_entry_cnt_minus_one; i++) {
                addr = sg_head->sg_list[i].addr + sg_head->sg_list[i].bytes;
                if (((ushort) addr & 0x0003) != 0) {
                    asc_dvc->in_critical_cnt--;
                    DvcLeaveCritical(last_int_level);
                    AscSetLibErrorCode(asc_dvc, ASCQ_ERR_SG_LIST_ODD_ADDRESS);
                    return (ERR);
                }
            }
        }
#endif
    }
    scsi_cmd = scsiq->cdbptr[0];
    disable_syn_offset_one_fix = FALSE;
    if ((asc_dvc->pci_fix_asyn_xfer & scsiq->q1.target_id) &&
        !(asc_dvc->pci_fix_asyn_xfer_always & scsiq->q1.target_id)) {
        if (scsiq->q1.cntl & QC_SG_HEAD) {
            data_cnt = 0;
            for (i = 0; i < sg_entry_cnt; i++) {
                data_cnt += sg_head->sg_list[i].bytes;
            }
        } else {
            data_cnt = scsiq->q1.data_cnt;
        }
        if (data_cnt != 0UL) {
            if (data_cnt < 512UL) {
                disable_syn_offset_one_fix = TRUE;
            } else {
                for (i = 0; i < ASC_SYN_OFFSET_ONE_DISABLE_LIST; i++) {
                    disable_cmd = _syn_offset_one_disable_cmd[i];
                    if (disable_cmd == 0xFF) {
                        break;
                    }
                    if (scsi_cmd == disable_cmd) {
                        disable_syn_offset_one_fix = TRUE;
                        break;
                    }
                }
            }
        }
    }
    if (disable_syn_offset_one_fix) {
        scsiq->q2.tag_code &= ~M2_QTAG_MSG_SIMPLE;
        scsiq->q2.tag_code |= (ASC_TAG_FLAG_DISABLE_ASYN_USE_SYN_FIX |
                               ASC_TAG_FLAG_DISABLE_DISCONNECT);
    } else {
        scsiq->q2.tag_code &= 0x23;
    }
    if ((scsiq->q1.cntl & QC_SG_HEAD) != 0) {
        if (asc_dvc->bug_fix_cntl) {
            if (asc_dvc->bug_fix_cntl & ASC_BUG_FIX_IF_NOT_DWB) {
                if ((scsi_cmd == SCSICMD_Read6) ||
                    (scsi_cmd == SCSICMD_Read10)) {
                    addr = sg_head->sg_list[sg_entry_cnt_minus_one].addr +
                      sg_head->sg_list[sg_entry_cnt_minus_one].bytes;
                    extra_bytes = (uchar) ((ushort) addr & 0x0003);
                    if ((extra_bytes != 0) &&
                        ((scsiq->q2.tag_code & ASC_TAG_FLAG_EXTRA_BYTES)
                         == 0)) {
                        scsiq->q2.tag_code |= ASC_TAG_FLAG_EXTRA_BYTES;
                        scsiq->q1.extra_bytes = extra_bytes;
                        sg_head->sg_list[sg_entry_cnt_minus_one].bytes -=
                            (ulong) extra_bytes;
                    }
                }
            }
        }
        sg_head->entry_to_copy = sg_head->entry_cnt;
        n_q_required = AscSgListToQueue(sg_entry_cnt);
        if ((AscGetNumOfFreeQueue(asc_dvc, target_ix, n_q_required) >=
            (uint) n_q_required) || ((scsiq->q1.cntl & QC_URGENT) != 0)) {
            if ((sta = AscSendScsiQueue(asc_dvc, scsiq,
                                        n_q_required)) == 1) {
                asc_dvc->in_critical_cnt--;
                if (asc_exe_callback != 0) {
                    (*asc_exe_callback) (asc_dvc, scsiq);
                }
                DvcLeaveCritical(last_int_level);
                return (sta);
            }
        }
    } else {
        if (asc_dvc->bug_fix_cntl) {
            if (asc_dvc->bug_fix_cntl & ASC_BUG_FIX_IF_NOT_DWB) {
                if ((scsi_cmd == SCSICMD_Read6) ||
                    (scsi_cmd == SCSICMD_Read10)) {
                    addr = scsiq->q1.data_addr + scsiq->q1.data_cnt;
                    extra_bytes = (uchar) ((ushort) addr & 0x0003);
                    if ((extra_bytes != 0) &&
                        ((scsiq->q2.tag_code & ASC_TAG_FLAG_EXTRA_BYTES)
                          == 0)) {
                        if (((ushort) scsiq->q1.data_cnt & 0x01FF) == 0) {
                            scsiq->q2.tag_code |= ASC_TAG_FLAG_EXTRA_BYTES;
                            scsiq->q1.data_cnt -= (ulong) extra_bytes;
                            scsiq->q1.extra_bytes = extra_bytes;
                        }
                    }
                }
            }
        }
        n_q_required = 1;
        if ((AscGetNumOfFreeQueue(asc_dvc, target_ix, 1) >= 1) ||
            ((scsiq->q1.cntl & QC_URGENT) != 0)) {
            if ((sta = AscSendScsiQueue(asc_dvc, scsiq,
                                        n_q_required)) == 1) {
                asc_dvc->in_critical_cnt--;
                if (asc_exe_callback != 0) {
                    (*asc_exe_callback) (asc_dvc, scsiq);
                }
                DvcLeaveCritical(last_int_level);
                return (sta);
            }
        }
    }
    asc_dvc->in_critical_cnt--;
    DvcLeaveCritical(last_int_level);
    return (sta);
}

STATIC int
AscSendScsiQueue(
                    REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                    REG ASC_SCSI_Q * scsiq,
                    uchar n_q_required
)
{
    PortAddr            iop_base;
    uchar               free_q_head;
    uchar               next_qp;
    uchar               tid_no;
    uchar               target_ix;
    int                 sta;
    iop_base = asc_dvc->iop_base;
    target_ix = scsiq->q2.target_ix;
    tid_no = ASC_TIX_TO_TID(target_ix);
    sta = 0;
    free_q_head = (uchar) AscGetVarFreeQHead(iop_base);
    if (n_q_required > 1) {
        if ((next_qp = AscAllocMultipleFreeQueue(iop_base,
                                       free_q_head, (uchar) (n_q_required)))
            != (uchar) ASC_QLINK_END) {
            asc_dvc->last_q_shortage = 0;
            scsiq->sg_head->queue_cnt = n_q_required - 1;
            scsiq->q1.q_no = free_q_head;
            if ((sta = AscPutReadySgListQueue(asc_dvc, scsiq,
                                              free_q_head)) == 1) {
#if CC_WRITE_IO_COUNT
                asc_dvc->req_count++;
#endif
                AscPutVarFreeQHead(iop_base, next_qp);
                asc_dvc->cur_total_qng += (uchar) (n_q_required);
                asc_dvc->cur_dvc_qng[tid_no]++;
            }
            return (sta);
        }
    } else if (n_q_required == 1) {
        if ((next_qp = AscAllocFreeQueue(iop_base,
                                         free_q_head)) != ASC_QLINK_END) {
            scsiq->q1.q_no = free_q_head;
            if ((sta = AscPutReadyQueue(asc_dvc, scsiq,
                                        free_q_head)) == 1) {
#if CC_WRITE_IO_COUNT
                asc_dvc->req_count++;
#endif
                AscPutVarFreeQHead(iop_base, next_qp);
                asc_dvc->cur_total_qng++;
                asc_dvc->cur_dvc_qng[tid_no]++;
            }
            return (sta);
        }
    }
    return (sta);
}

STATIC int
AscSgListToQueue(
                    int sg_list
)
{
    int                 n_sg_list_qs;
    n_sg_list_qs = ((sg_list - 1) / ASC_SG_LIST_PER_Q);
    if (((sg_list - 1) % ASC_SG_LIST_PER_Q) != 0)
        n_sg_list_qs++;
    return (n_sg_list_qs + 1);
}


STATIC uint
AscGetNumOfFreeQueue(
                        REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                        uchar target_ix,
                        uchar n_qs
)
{
    uint                cur_used_qs;
    uint                cur_free_qs;
    ASC_SCSI_BIT_ID_TYPE target_id;
    uchar               tid_no;
    target_id = ASC_TIX_TO_TARGET_ID(target_ix);
    tid_no = ASC_TIX_TO_TID(target_ix);
    if ((asc_dvc->unit_not_ready & target_id) ||
        (asc_dvc->queue_full_or_busy & target_id)) {
        return (0);
    }
    if (n_qs == 1) {
        cur_used_qs = (uint) asc_dvc->cur_total_qng +
          (uint) asc_dvc->last_q_shortage +
          (uint) ASC_MIN_FREE_Q;
    } else {
        cur_used_qs = (uint) asc_dvc->cur_total_qng +
          (uint) ASC_MIN_FREE_Q;
    }
    if ((uint) (cur_used_qs + n_qs) <= (uint) asc_dvc->max_total_qng) {
        cur_free_qs = (uint) asc_dvc->max_total_qng - cur_used_qs;
        if (asc_dvc->cur_dvc_qng[tid_no] >=
            asc_dvc->max_dvc_qng[tid_no]) {
            return (0);
        }
        return (cur_free_qs);
    }
    if (n_qs > 1) {
        if ((n_qs > asc_dvc->last_q_shortage) && (n_qs <= (asc_dvc->max_total_qng - ASC_MIN_FREE_Q))) {
            asc_dvc->last_q_shortage = n_qs;
        }
    }
    return (0);
}

STATIC int
AscPutReadyQueue(
                    REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                    REG ASC_SCSI_Q * scsiq,
                    uchar q_no
)
{
    ushort              q_addr;
    uchar               tid_no;
    uchar               sdtr_data;
    uchar               syn_period_ix;
    uchar               syn_offset;
    PortAddr            iop_base;
    iop_base = asc_dvc->iop_base;
    if (((asc_dvc->init_sdtr & scsiq->q1.target_id) != 0) &&
        ((asc_dvc->sdtr_done & scsiq->q1.target_id) == 0)) {
        tid_no = ASC_TIX_TO_TID(scsiq->q2.target_ix);
        sdtr_data = AscGetMCodeInitSDTRAtID(iop_base, tid_no);
        syn_period_ix = (sdtr_data >> 4) & (asc_dvc->max_sdtr_index - 1);
        syn_offset = sdtr_data & ASC_SYN_MAX_OFFSET;
        AscMsgOutSDTR(asc_dvc,
                      asc_dvc->sdtr_period_tbl[syn_period_ix],
                      syn_offset);
        scsiq->q1.cntl |= QC_MSG_OUT;
    }
    q_addr = ASC_QNO_TO_QADDR(q_no);
    if ((scsiq->q1.target_id & asc_dvc->use_tagged_qng) == 0) {
        scsiq->q2.tag_code &= ~M2_QTAG_MSG_SIMPLE;
    }
    scsiq->q1.status = QS_FREE;
    AscMemWordCopyToLram(iop_base,
                         (ushort) (q_addr + (ushort) ASC_SCSIQ_CDB_BEG),
                         (ushort *) scsiq->cdbptr,
                         (ushort) ((ushort) scsiq->q2.cdb_len >> 1));
#if !CC_LITTLE_ENDIAN_HOST
    AscAdjEndianScsiQ(scsiq);
#endif
    DvcPutScsiQ(iop_base,
                (ushort) (q_addr + (ushort) ASC_SCSIQ_CPY_BEG),
                (ushort *) & scsiq->q1.cntl,
      (ushort) ((((sizeof (ASC_SCSIQ_1) + sizeof (ASC_SCSIQ_2)) / 2) - 1)));
#if CC_WRITE_IO_COUNT
    AscWriteLramWord(iop_base,
                     (ushort) (q_addr + (ushort) ASC_SCSIQ_W_REQ_COUNT),
                     (ushort) asc_dvc->req_count);
#endif
#if CC_VERIFY_LRAM_COPY
    if ((asc_dvc->dvc_cntl & ASC_CNTL_NO_VERIFY_COPY) == 0) {
        if (AscMemWordCmpToLram(iop_base,
                             (ushort) (q_addr + (ushort) ASC_SCSIQ_CDB_BEG),
                                (ushort *) scsiq->cdbptr,
                                (ushort) (scsiq->q2.cdb_len >> 1)) != 0) {
            AscSetLibErrorCode(asc_dvc, ASCQ_ERR_LOCAL_MEM);
            return (ERR);
        }
        if (AscMemWordCmpToLram(iop_base,
                             (ushort) (q_addr + (ushort) ASC_SCSIQ_CPY_BEG),
                                (ushort *) & scsiq->q1.cntl,
         (ushort) (((sizeof (ASC_SCSIQ_1) + sizeof (ASC_SCSIQ_2)) / 2) - 1))
            != 0) {
            AscSetLibErrorCode(asc_dvc, ASCQ_ERR_LOCAL_MEM);
            return (ERR);
        }
    }
#endif
#if CC_CLEAR_DMA_REMAIN
    AscWriteLramDWord(iop_base,
           (ushort) (q_addr + (ushort) ASC_SCSIQ_DW_REMAIN_XFER_ADDR), 0UL);
    AscWriteLramDWord(iop_base,
            (ushort) (q_addr + (ushort) ASC_SCSIQ_DW_REMAIN_XFER_CNT), 0UL);
#endif
    AscWriteLramWord(iop_base,
                     (ushort) (q_addr + (ushort) ASC_SCSIQ_B_STATUS),
             (ushort) (((ushort) scsiq->q1.q_no << 8) | (ushort) QS_READY));
    return (1);
}

STATIC int
AscPutReadySgListQueue(
                          REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                          REG ASC_SCSI_Q * scsiq,
                          uchar q_no
)
{
    int                 sta;
    int                 i;
    ASC_SG_HEAD *sg_head;
    ASC_SG_LIST_Q       scsi_sg_q;
    ulong               saved_data_addr;
    ulong               saved_data_cnt;
    PortAddr            iop_base;
    ushort              sg_list_dwords;
    ushort              sg_index;
    ushort              sg_entry_cnt;
    ushort              q_addr;
    uchar               next_qp;
    iop_base = asc_dvc->iop_base;
    sg_head = scsiq->sg_head;
    saved_data_addr = scsiq->q1.data_addr;
    saved_data_cnt = scsiq->q1.data_cnt;
    scsiq->q1.data_addr = sg_head->sg_list[0].addr;
    scsiq->q1.data_cnt = sg_head->sg_list[0].bytes;
    sg_entry_cnt = sg_head->entry_cnt - 1;
    if (sg_entry_cnt != 0) {
        scsiq->q1.cntl |= QC_SG_HEAD;
        q_addr = ASC_QNO_TO_QADDR(q_no);
        sg_index = 1;
        scsiq->q1.sg_queue_cnt = sg_head->queue_cnt;
        scsi_sg_q.sg_head_qp = q_no;
        scsi_sg_q.cntl = QCSG_SG_XFER_LIST;
        for (i = 0; i < sg_head->queue_cnt; i++) {
            scsi_sg_q.seq_no = i + 1;
            if (sg_entry_cnt > ASC_SG_LIST_PER_Q) {
                sg_list_dwords = (uchar) (ASC_SG_LIST_PER_Q * 2);
                sg_entry_cnt -= ASC_SG_LIST_PER_Q;
                if (i == 0) {
                    scsi_sg_q.sg_list_cnt = ASC_SG_LIST_PER_Q;
                    scsi_sg_q.sg_cur_list_cnt = ASC_SG_LIST_PER_Q;
                } else {
                    scsi_sg_q.sg_list_cnt = ASC_SG_LIST_PER_Q - 1;
                    scsi_sg_q.sg_cur_list_cnt = ASC_SG_LIST_PER_Q - 1;
                }
            } else {
                scsi_sg_q.cntl |= QCSG_SG_XFER_END;
                sg_list_dwords = sg_entry_cnt << 1;
                if (i == 0) {
                    scsi_sg_q.sg_list_cnt = sg_entry_cnt;
                    scsi_sg_q.sg_cur_list_cnt = sg_entry_cnt;
                } else {
                    scsi_sg_q.sg_list_cnt = sg_entry_cnt - 1;
                    scsi_sg_q.sg_cur_list_cnt = sg_entry_cnt - 1;
                }
                sg_entry_cnt = 0;
            }
            next_qp = AscReadLramByte(iop_base,
                                      (ushort) (q_addr + ASC_SCSIQ_B_FWD));
            scsi_sg_q.q_no = next_qp;
            q_addr = ASC_QNO_TO_QADDR(next_qp);
            AscMemWordCopyToLram(iop_base,
                                 (ushort) (q_addr + ASC_SCSIQ_SGHD_CPY_BEG),
                                 (ushort *) & scsi_sg_q,
                                 (ushort) (sizeof (ASC_SG_LIST_Q) >> 1));
            AscMemDWordCopyToLram(iop_base,
                                  (ushort) (q_addr + ASC_SGQ_LIST_BEG),
                              (ulong *) & sg_head->sg_list[sg_index],
                                  (ushort) sg_list_dwords);
            sg_index += ASC_SG_LIST_PER_Q;
        }
    } else {
        scsiq->q1.cntl &= ~QC_SG_HEAD;
    }
    sta = AscPutReadyQueue(asc_dvc, scsiq, q_no);
    scsiq->q1.data_addr = saved_data_addr;
    scsiq->q1.data_cnt = saved_data_cnt;
    return (sta);
}

STATIC int
AscAbortSRB(
               REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
               ulong srb_ptr
)
{
    int                 sta;
    ASC_SCSI_BIT_ID_TYPE saved_unit_not_ready;
    PortAddr            iop_base;
    iop_base = asc_dvc->iop_base;
    sta = ERR;
    saved_unit_not_ready = asc_dvc->unit_not_ready;
    asc_dvc->unit_not_ready = 0xFF;
    AscWaitISRDone(asc_dvc);
    if (AscStopQueueExe(iop_base) == 1) {
        if (AscRiscHaltedAbortSRB(asc_dvc, srb_ptr) == 1) {
            sta = 1;
            AscCleanUpBusyQueue(iop_base);
            AscStartQueueExe(iop_base);
        } else {
            sta = 0;
            AscStartQueueExe(iop_base);
        }
    }
    asc_dvc->unit_not_ready = saved_unit_not_ready;
    return (sta);
}

#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,89)
STATIC int
AscResetDevice(
                  REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                  uchar target_ix
)
{
    PortAddr            iop_base;
    int                 sta;
    uchar               tid_no;
    ASC_SCSI_BIT_ID_TYPE target_id;
    int                 i;
    ASC_SCSI_REQ_Q      scsiq_buf;
    ASC_SCSI_REQ_Q *scsiq;
    uchar       *buf;
    ASC_SCSI_BIT_ID_TYPE saved_unit_not_ready;
    iop_base = asc_dvc->iop_base;
    tid_no = ASC_TIX_TO_TID(target_ix);
    target_id = ASC_TID_TO_TARGET_ID(tid_no);
    saved_unit_not_ready = asc_dvc->unit_not_ready;
    asc_dvc->unit_not_ready = target_id;
    sta = ERR;
    AscWaitTixISRDone(asc_dvc, target_ix);
    if (AscStopQueueExe(iop_base) == 1) {
        if (AscRiscHaltedAbortTIX(asc_dvc, target_ix) == 1) {
            AscCleanUpBusyQueue(iop_base);
            AscStartQueueExe(iop_base);
            AscWaitTixISRDone(asc_dvc, target_ix);
            sta = TRUE;
            scsiq = (ASC_SCSI_REQ_Q *) & scsiq_buf;
            buf = (uchar *) & scsiq_buf;
            for (i = 0; i < sizeof (ASC_SCSI_REQ_Q); i++) {
                *buf++ = 0x00;
            }
            scsiq->r1.status = (uchar) QS_READY;
            scsiq->r2.cdb_len = 6;
            scsiq->r2.tag_code = M2_QTAG_MSG_SIMPLE;
            scsiq->r1.target_id = target_id;
            scsiq->r2.target_ix = ASC_TIDLUN_TO_IX(tid_no, 0);
            scsiq->cdbptr = (uchar *) scsiq->cdb;
            scsiq->r1.cntl = QC_NO_CALLBACK | QC_MSG_OUT | QC_URGENT;
            AscWriteLramByte(asc_dvc->iop_base, ASCV_MSGOUT_BEG,
                             M1_BUS_DVC_RESET);
            asc_dvc->unit_not_ready &= ~target_id;
            asc_dvc->sdtr_done |= target_id;
            if (AscExeScsiQueue(asc_dvc, (ASC_SCSI_Q *) scsiq)
                == 1) {
                asc_dvc->unit_not_ready = target_id;
                DvcSleepMilliSecond(1000);
                _AscWaitQDone(iop_base, (ASC_SCSI_Q *) scsiq);
                if (AscStopQueueExe(iop_base) == 1) {
                    AscCleanUpDiscQueue(iop_base);
                    AscStartQueueExe(iop_base);
                    if (asc_dvc->pci_fix_asyn_xfer & target_id) {
                        AscSetRunChipSynRegAtID(iop_base, tid_no,
                                             ASYN_SDTR_DATA_FIX_PCI_REV_AB);
                    }
                    AscWaitTixISRDone(asc_dvc, target_ix);
                }
            } else {
                sta = 0;
            }
            asc_dvc->sdtr_done &= ~target_id;
        } else {
            sta = ERR;
            AscStartQueueExe(iop_base);
        }
    }
    asc_dvc->unit_not_ready = saved_unit_not_ready;
    return (sta);
}
#endif /* version >= v1.3.89 */

STATIC int
AscResetSB(
              REG ASC_DVC_VAR asc_ptr_type * asc_dvc
)
{
    int                 sta;
    int                 i;
    PortAddr            iop_base;
    iop_base = asc_dvc->iop_base;
    asc_dvc->unit_not_ready = 0xFF;
    sta = TRUE;
    AscWaitISRDone(asc_dvc);
    AscStopQueueExe(iop_base);
    asc_dvc->sdtr_done = 0;
    AscResetChipAndScsiBus(iop_base);
    DvcSleepMilliSecond((ulong) ((ushort) asc_dvc->scsi_reset_wait * 1000));
    AscReInitLram(asc_dvc);
    for (i = 0; i <= ASC_MAX_TID; i++) {
        asc_dvc->cur_dvc_qng[i] = 0;
        if (asc_dvc->pci_fix_asyn_xfer & (ASC_SCSI_BIT_ID_TYPE) (0x01 << i)) {
            AscSetChipSynRegAtID(iop_base, i, ASYN_SDTR_DATA_FIX_PCI_REV_AB);
        }
    }
    asc_dvc->err_code = 0;
    AscSetPCAddr(iop_base, ASC_MCODE_START_ADDR);
    if (AscGetPCAddr(iop_base) != ASC_MCODE_START_ADDR) {
        sta = ERR;
    }
    if (AscStartChip(iop_base) == 0) {
        sta = ERR;
    }
    AscStartQueueExe(iop_base);
    asc_dvc->unit_not_ready = 0;
    asc_dvc->queue_full_or_busy = 0;
    return (sta);
}

STATIC int
AscSetRunChipSynRegAtID(
                           PortAddr iop_base,
                           uchar tid_no,
                           uchar sdtr_data
)
{
    int                 sta = FALSE;
    if (AscHostReqRiscHalt(iop_base)) {
        sta = AscSetChipSynRegAtID(iop_base, tid_no, sdtr_data);
        AscStartChip(iop_base);
        return (sta);
    }
    return (sta);
}

STATIC int
AscSetChipSynRegAtID(
                        PortAddr iop_base,
                        uchar id,
                        uchar sdtr_data
)
{
    ASC_SCSI_BIT_ID_TYPE org_id;
    int                 i;
    int                 sta;
    sta = TRUE;
    AscSetBank(iop_base, 1);
    org_id = AscReadChipDvcID(iop_base);
    for (i = 0; i <= ASC_MAX_TID; i++) {
        if (org_id == (0x01 << i))
            break;
    }
    org_id = i;
    AscWriteChipDvcID(iop_base, id);
    if (AscReadChipDvcID(iop_base) == (0x01 << id)) {
        AscSetBank(iop_base, 0);
        AscSetChipSyn(iop_base, sdtr_data);
        if (AscGetChipSyn(iop_base) != sdtr_data) {
            sta = FALSE;
        }
    } else {
        sta = FALSE;
    }
    AscSetBank(iop_base, 1);
    AscWriteChipDvcID(iop_base, org_id);
    AscSetBank(iop_base, 0);
    return (sta);
}

STATIC int
AscReInitLram(
                 REG ASC_DVC_VAR asc_ptr_type * asc_dvc
)
{
    AscInitLram(asc_dvc);
    AscInitQLinkVar(asc_dvc);
    return (0);
}

STATIC ushort
AscInitLram(
               REG ASC_DVC_VAR asc_ptr_type * asc_dvc
)
{
    uchar               i;
    ushort              s_addr;
    PortAddr            iop_base;
    ushort              warn_code;
    iop_base = asc_dvc->iop_base;
    warn_code = 0;
    AscMemWordSetLram(iop_base, ASC_QADR_BEG, 0,
               (ushort) (((int) (asc_dvc->max_total_qng + 2 + 1) * 64) >> 1)
);
    i = ASC_MIN_ACTIVE_QNO;
    s_addr = ASC_QADR_BEG + ASC_QBLK_SIZE;
    AscWriteLramByte(iop_base, (ushort) (s_addr + ASC_SCSIQ_B_FWD),
                     (uchar) (i + 1));
    AscWriteLramByte(iop_base, (ushort) (s_addr + ASC_SCSIQ_B_BWD),
                     (uchar) (asc_dvc->max_total_qng));
    AscWriteLramByte(iop_base, (ushort) (s_addr + ASC_SCSIQ_B_QNO),
                     (uchar) i);
    i++;
    s_addr += ASC_QBLK_SIZE;
    for (; i < asc_dvc->max_total_qng; i++, s_addr += ASC_QBLK_SIZE) {
        AscWriteLramByte(iop_base, (ushort) (s_addr + ASC_SCSIQ_B_FWD),
                         (uchar) (i + 1));
        AscWriteLramByte(iop_base, (ushort) (s_addr + ASC_SCSIQ_B_BWD),
                         (uchar) (i - 1));
        AscWriteLramByte(iop_base, (ushort) (s_addr + ASC_SCSIQ_B_QNO),
                         (uchar) i);
    }
    AscWriteLramByte(iop_base, (ushort) (s_addr + ASC_SCSIQ_B_FWD),
                     (uchar) ASC_QLINK_END);
    AscWriteLramByte(iop_base, (ushort) (s_addr + ASC_SCSIQ_B_BWD),
                     (uchar) (asc_dvc->max_total_qng - 1));
    AscWriteLramByte(iop_base, (ushort) (s_addr + ASC_SCSIQ_B_QNO),
                     (uchar) asc_dvc->max_total_qng);
    i++;
    s_addr += ASC_QBLK_SIZE;
    for (; i <= (uchar) (asc_dvc->max_total_qng + 3);
         i++, s_addr += ASC_QBLK_SIZE) {
        AscWriteLramByte(iop_base,
                         (ushort) (s_addr + (ushort) ASC_SCSIQ_B_FWD), i);
        AscWriteLramByte(iop_base,
                         (ushort) (s_addr + (ushort) ASC_SCSIQ_B_BWD), i);
        AscWriteLramByte(iop_base,
                         (ushort) (s_addr + (ushort) ASC_SCSIQ_B_QNO), i);
    }
    return (warn_code);
}

STATIC ushort
AscInitQLinkVar(
                   REG ASC_DVC_VAR asc_ptr_type * asc_dvc
)
{
    PortAddr            iop_base;
    int                 i;
    ushort              lram_addr;
    iop_base = asc_dvc->iop_base;
    AscPutRiscVarFreeQHead(iop_base, 1);
    AscPutRiscVarDoneQTail(iop_base, asc_dvc->max_total_qng);
    AscPutVarFreeQHead(iop_base, 1);
    AscPutVarDoneQTail(iop_base, asc_dvc->max_total_qng);
    AscWriteLramByte(iop_base, ASCV_BUSY_QHEAD_B,
                     (uchar) ((int) asc_dvc->max_total_qng + 1));
    AscWriteLramByte(iop_base, ASCV_DISC1_QHEAD_B,
                     (uchar) ((int) asc_dvc->max_total_qng + 2));
    AscWriteLramByte(iop_base, (ushort) ASCV_TOTAL_READY_Q_B,
                     asc_dvc->max_total_qng);
    AscWriteLramWord(iop_base, ASCV_ASCDVC_ERR_CODE_W, 0);
    AscWriteLramWord(iop_base, ASCV_HALTCODE_W, 0);
    AscWriteLramByte(iop_base, ASCV_STOP_CODE_B, 0);
    AscWriteLramByte(iop_base, ASCV_SCSIBUSY_B, 0);
    AscWriteLramByte(iop_base, ASCV_WTM_FLAG_B, 0);
    AscPutQDoneInProgress(iop_base, 0);
    lram_addr = ASC_QADR_BEG;
    for (i = 0; i < 32; i++, lram_addr += 2) {
        AscWriteLramWord(iop_base, lram_addr, 0);
    }
    return (0);
}

STATIC int
AscSetLibErrorCode(
                      REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                      ushort err_code
)
{
    if (asc_dvc->err_code == 0) {
        asc_dvc->err_code = err_code;
        AscWriteLramWord(asc_dvc->iop_base, ASCV_ASCDVC_ERR_CODE_W,
                         err_code);
    }
    return (err_code);
}


#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,89)
STATIC int
_AscWaitQDone(
                 PortAddr iop_base,
                 REG ASC_SCSI_Q * scsiq
)
{
    ushort              q_addr;
    uchar               q_status;
    int                 count = 0;
    while (scsiq->q1.q_no == 0) ;
    q_addr = ASC_QNO_TO_QADDR(scsiq->q1.q_no);
    do {
        q_status = AscReadLramByte(iop_base, q_addr + ASC_SCSIQ_B_STATUS);
        DvcSleepMilliSecond(100L);
        if (count++ > 30) {
            return (0);
        }
    } while ((q_status & QS_READY) != 0);
    return (1);
}
#endif /* version >= v1.3.89 */

STATIC uchar 
AscMsgOutSDTR(
                 REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                 uchar sdtr_period,
                 uchar sdtr_offset
)
{
    EXT_MSG             sdtr_buf;
    uchar               sdtr_period_index;
    PortAddr            iop_base;

    iop_base = asc_dvc->iop_base;
    sdtr_buf.msg_type = MS_EXTEND;
    sdtr_buf.msg_len = MS_SDTR_LEN;
    sdtr_buf.msg_req = MS_SDTR_CODE;
    sdtr_buf.xfer_period = sdtr_period;
    sdtr_offset &= ASC_SYN_MAX_OFFSET;
    sdtr_buf.req_ack_offset = sdtr_offset;
    if ((sdtr_period_index =
         AscGetSynPeriodIndex(asc_dvc, sdtr_period)) <=
        asc_dvc->max_sdtr_index) {
        AscMemWordCopyToLram(iop_base,
                             ASCV_MSGOUT_BEG,
                             (ushort *) & sdtr_buf,
                             (ushort) (sizeof (EXT_MSG) >> 1));
        return ((sdtr_period_index << 4) | sdtr_offset);
    } else {

        sdtr_buf.req_ack_offset = 0;
        AscMemWordCopyToLram(iop_base,
                             ASCV_MSGOUT_BEG,
                             (ushort *) & sdtr_buf,
                             (ushort) (sizeof (EXT_MSG) >> 1));
        return (0);
    }
}

STATIC uchar
AscCalSDTRData(
                  REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                  uchar sdtr_period,
                  uchar syn_offset
)
{
    uchar               byte;
    uchar               sdtr_period_ix;
    sdtr_period_ix = AscGetSynPeriodIndex(asc_dvc, sdtr_period);
    if (
           (sdtr_period_ix > asc_dvc->max_sdtr_index)
) {
        return (0xFF);
    }
    byte = (sdtr_period_ix << 4) | (syn_offset & ASC_SYN_MAX_OFFSET);
    return (byte);
}

STATIC void
AscSetChipSDTR(
                  PortAddr iop_base,
                  uchar sdtr_data,
                  uchar tid_no
)
{
    AscSetChipSynRegAtID(iop_base, tid_no, sdtr_data);
    AscPutMCodeSDTRDoneAtID(iop_base, tid_no, sdtr_data);
    return;
}

STATIC uchar
AscGetSynPeriodIndex(
                        ASC_DVC_VAR asc_ptr_type * asc_dvc,
                        ruchar syn_time
)
{
    ruchar             *period_table;
    int                 max_index;
    int                 min_index;
    int                 i;
    period_table = asc_dvc->sdtr_period_tbl;
    max_index = (int) asc_dvc->max_sdtr_index;
    min_index = (int)asc_dvc->host_init_sdtr_index ;
    if ((syn_time <= period_table[max_index])) {
        for (i = min_index; i < (max_index - 1); i++) {
            if (syn_time <= period_table[i]) {
                return ((uchar) i);
            }
        }
        return ((uchar) max_index);
    } else {
        return ((uchar) (max_index + 1));
    }
}

STATIC uchar
AscAllocFreeQueue(
                     PortAddr iop_base,
                     uchar free_q_head
)
{
    ushort              q_addr;
    uchar               next_qp;
    uchar               q_status;
    q_addr = ASC_QNO_TO_QADDR(free_q_head);
    q_status = (uchar) AscReadLramByte(iop_base,
                                    (ushort) (q_addr + ASC_SCSIQ_B_STATUS));
    next_qp = AscReadLramByte(iop_base,
                              (ushort) (q_addr + ASC_SCSIQ_B_FWD));
    if (((q_status & QS_READY) == 0) && (next_qp != ASC_QLINK_END)) {
        return (next_qp);
    }
    return (ASC_QLINK_END);
}

STATIC uchar
AscAllocMultipleFreeQueue(
                             PortAddr iop_base,
                             uchar free_q_head,
                             uchar n_free_q
)
{
    uchar               i;
    for (i = 0; i < n_free_q; i++) {
        if ((free_q_head = AscAllocFreeQueue(iop_base, free_q_head))
            == ASC_QLINK_END) {
            return (ASC_QLINK_END);
        }
    }
    return (free_q_head);
}

STATIC int
AscRiscHaltedAbortSRB(
                         REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                         ulong srb_ptr
)
{
    PortAddr            iop_base;
    ushort              q_addr;
    uchar               q_no;
    ASC_QDONE_INFO      scsiq_buf;
    ASC_QDONE_INFO *scsiq;
    ASC_ISR_CALLBACK    asc_isr_callback;
    int                 last_int_level;
    iop_base = asc_dvc->iop_base;
    asc_isr_callback = (ASC_ISR_CALLBACK) asc_dvc->isr_callback;
    last_int_level = DvcEnterCritical();
    scsiq = (ASC_QDONE_INFO *) & scsiq_buf;
    for (q_no = ASC_MIN_ACTIVE_QNO; q_no <= asc_dvc->max_total_qng;
         q_no++) {
        q_addr = ASC_QNO_TO_QADDR(q_no);
        scsiq->d2.srb_ptr = AscReadLramDWord(iop_base,
                           (ushort) (q_addr + (ushort) ASC_SCSIQ_D_SRBPTR));
        if (scsiq->d2.srb_ptr == srb_ptr) {
            _AscCopyLramScsiDoneQ(iop_base, q_addr, scsiq, asc_dvc->max_dma_count);
            if (((scsiq->q_status & QS_READY) != 0)
                 && ((scsiq->q_status & QS_ABORTED) == 0)
                 && ((scsiq->cntl & QCSG_SG_XFER_LIST) == 0)) {
                scsiq->q_status |= QS_ABORTED;
                scsiq->d3.done_stat = QD_ABORTED_BY_HOST;
                AscWriteLramDWord(iop_base,
                            (ushort) (q_addr + (ushort) ASC_SCSIQ_D_SRBPTR),
                                  0L);
                AscWriteLramByte(iop_base,
                            (ushort) (q_addr + (ushort) ASC_SCSIQ_B_STATUS),
                                 scsiq->q_status);
                (*asc_isr_callback) (asc_dvc, scsiq);
                return (1);
            }
        }
    }
    DvcLeaveCritical(last_int_level);
    return (0);
}

#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,89)
STATIC int
AscRiscHaltedAbortTIX(
                         REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                         uchar target_ix
)
{
    PortAddr            iop_base;
    ushort              q_addr;
    uchar               q_no;
    ASC_QDONE_INFO      scsiq_buf;
    ASC_QDONE_INFO *scsiq;
    ASC_ISR_CALLBACK    asc_isr_callback;
    int                 last_int_level;
    iop_base = asc_dvc->iop_base;
    asc_isr_callback = (ASC_ISR_CALLBACK) asc_dvc->isr_callback;
    last_int_level = DvcEnterCritical();
    scsiq = (ASC_QDONE_INFO *) & scsiq_buf;
    for (q_no = ASC_MIN_ACTIVE_QNO; q_no <= asc_dvc->max_total_qng;
         q_no++) {
        q_addr = ASC_QNO_TO_QADDR(q_no);
        _AscCopyLramScsiDoneQ(iop_base, q_addr, scsiq, asc_dvc->max_dma_count);
        if (((scsiq->q_status & QS_READY) != 0) &&
            ((scsiq->q_status & QS_ABORTED) == 0) &&
            ((scsiq->cntl & QCSG_SG_XFER_LIST) == 0)) {
            if (scsiq->d2.target_ix == target_ix) {
                scsiq->q_status |= QS_ABORTED;
                scsiq->d3.done_stat = QD_ABORTED_BY_HOST;
                AscWriteLramDWord(iop_base,
                            (ushort) (q_addr + (ushort) ASC_SCSIQ_D_SRBPTR),
                                  0L);
                AscWriteLramByte(iop_base,
                            (ushort) (q_addr + (ushort) ASC_SCSIQ_B_STATUS),
                                 scsiq->q_status);
                (*asc_isr_callback) (asc_dvc, scsiq);
            }
        }
    }
    DvcLeaveCritical(last_int_level);
    return (1);
}
#endif /* version >= v1.3.89 */

STATIC int
AscHostReqRiscHalt(
                      PortAddr iop_base
)
{
    int                 count = 0;
    int                 sta = 0;
    uchar               saved_stop_code;
    if (AscIsChipHalted(iop_base))
        return (1);
    saved_stop_code = AscReadLramByte(iop_base, ASCV_STOP_CODE_B);
    AscWriteLramByte(iop_base, ASCV_STOP_CODE_B,
                     ASC_STOP_HOST_REQ_RISC_HALT | ASC_STOP_REQ_RISC_STOP
);
    do {
        if (AscIsChipHalted(iop_base)) {
            sta = 1;
            break;
        }
        DvcSleepMilliSecond(100);
    } while (count++ < 20);
    AscWriteLramByte(iop_base, ASCV_STOP_CODE_B, saved_stop_code);
    return (sta);
}

STATIC int
AscStopQueueExe(
                   PortAddr iop_base
)
{
    int                 count;
    count = 0;
    if (AscReadLramByte(iop_base, ASCV_STOP_CODE_B) == 0) {
        AscWriteLramByte(iop_base, ASCV_STOP_CODE_B,
                         ASC_STOP_REQ_RISC_STOP);
        do {
            if (
                   AscReadLramByte(iop_base, ASCV_STOP_CODE_B) &
                   ASC_STOP_ACK_RISC_STOP) {
                return (1);
            }
            DvcSleepMilliSecond(100);
        } while (count++ < 20);
    }
    return (0);
}

STATIC int
AscStartQueueExe(
                    PortAddr iop_base
)
{
    if (AscReadLramByte(iop_base, ASCV_STOP_CODE_B) != 0) {
        AscWriteLramByte(iop_base, ASCV_STOP_CODE_B, 0);
    }
    return (1);
}

STATIC int
AscCleanUpBusyQueue(
                       PortAddr iop_base
)
{
    int                 count;
    uchar               stop_code;
    count = 0;
    if (AscReadLramByte(iop_base, ASCV_STOP_CODE_B) != 0) {
        AscWriteLramByte(iop_base, ASCV_STOP_CODE_B,
                         ASC_STOP_CLEAN_UP_BUSY_Q);
        do {
            stop_code = AscReadLramByte(iop_base, ASCV_STOP_CODE_B);
            if ((stop_code & ASC_STOP_CLEAN_UP_BUSY_Q) == 0)
                break;
            DvcSleepMilliSecond(100);
        } while (count++ < 20);
    }
    return (1);
}

#if LINUX_VERSION_CODE >= ASC_LINUX_VERSION(1,3,89)
STATIC int
AscCleanUpDiscQueue(
                       PortAddr iop_base
)
{
    int                 count;
    uchar               stop_code;
    count = 0;
    if (AscReadLramByte(iop_base, ASCV_STOP_CODE_B) != 0) {
        AscWriteLramByte(iop_base, ASCV_STOP_CODE_B,
                         ASC_STOP_CLEAN_UP_DISC_Q);
        do {
            stop_code = AscReadLramByte(iop_base, ASCV_STOP_CODE_B);
            if ((stop_code & ASC_STOP_CLEAN_UP_DISC_Q) == 0)
                break;
            DvcSleepMilliSecond(100);
        } while (count++ < 20);
    }
    return (1);
}
#endif /* version >= v1.3.89 */

STATIC int
AscWaitTixISRDone(
                     ASC_DVC_VAR asc_ptr_type * asc_dvc,
                     uchar target_ix
)
{
    uchar               cur_req;
    uchar               tid_no;
    tid_no = ASC_TIX_TO_TID(target_ix);
    while (TRUE) {
        if ((cur_req = asc_dvc->cur_dvc_qng[tid_no]) == 0) {
            break;
        }
        DvcSleepMilliSecond(1000L);
        if (asc_dvc->cur_dvc_qng[tid_no] == cur_req) {
            break;
        }
    }
    return (1);
}

STATIC int
AscWaitISRDone(
                  REG ASC_DVC_VAR asc_ptr_type * asc_dvc
)
{
    int                 tid;
    for (tid = 0; tid <= ASC_MAX_TID; tid++) {
        AscWaitTixISRDone(asc_dvc, ASC_TID_TO_TIX(tid));
    }
    return (1);
}

STATIC ulong
AscGetOnePhyAddr(
                    REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                    uchar * buf_addr,
                    ulong buf_size
)
{
    ASC_MIN_SG_HEAD     sg_head;
    sg_head.entry_cnt = ASC_MIN_SG_LIST;
    if (DvcGetSGList(asc_dvc, (uchar *) buf_addr,
                  buf_size, (ASC_SG_HEAD *) & sg_head) != buf_size) {
        return (0L);
    }
    if (sg_head.entry_cnt > 1) {
        return (0L);
    }
    return (sg_head.sg_list[0].addr);
}

STATIC void
DvcDelayNanoSecond(
                      ASC_DVC_VAR asc_ptr_type * asc_dvc,
                      ulong nano_sec
)
{
    ulong               loop;
    PortAddr            iop_base;
    iop_base = asc_dvc->iop_base;
    loop = nano_sec / 90;
    loop++;
    while (loop-- != 0) {
        inp(iop_base);
    }
    return;
}

ASC_INITFUNC(
STATIC ulong
AscGetEisaProductID(
                       PortAddr iop_base
)
)
{
    PortAddr            eisa_iop;
    ushort              product_id_high, product_id_low;
    ulong               product_id;
    eisa_iop = ASC_GET_EISA_SLOT(iop_base) | ASC_EISA_PID_IOP_MASK;
    product_id_low = inpw(eisa_iop);
    product_id_high = inpw(eisa_iop + 2);
    product_id = ((ulong) product_id_high << 16) | (ulong) product_id_low;
    return (product_id);
}

ASC_INITFUNC(
STATIC PortAddr
AscSearchIOPortAddrEISA(
                           PortAddr iop_base
)
)
{
    ulong               eisa_product_id;
    if (iop_base == 0) {
        iop_base = ASC_EISA_MIN_IOP_ADDR;
    } else {
        if (iop_base == ASC_EISA_MAX_IOP_ADDR)
            return (0);
        if ((iop_base & 0x0050) == 0x0050) {
            iop_base += ASC_EISA_BIG_IOP_GAP;
        } else {
            iop_base += ASC_EISA_SMALL_IOP_GAP;
        }
    }
    while (iop_base <= ASC_EISA_MAX_IOP_ADDR) {
        eisa_product_id = AscGetEisaProductID(iop_base);
        if ((eisa_product_id == ASC_EISA_ID_740) ||
            (eisa_product_id == ASC_EISA_ID_750)) {
            if (AscFindSignature(iop_base)) {
                inpw(iop_base + 4);
                return (iop_base);
            }
        }
        if (iop_base == ASC_EISA_MAX_IOP_ADDR)
            return (0);
        if ((iop_base & 0x0050) == 0x0050) {
            iop_base += ASC_EISA_BIG_IOP_GAP;
        } else {
            iop_base += ASC_EISA_SMALL_IOP_GAP;
        }
    }
    return (0);
}

STATIC int
AscStartChip(
                PortAddr iop_base
)
{
    AscSetChipControl(iop_base, 0);
    if ((AscGetChipStatus(iop_base) & CSW_HALTED) != 0) {
        return (0);
    }
    return (1);
}

STATIC int
AscStopChip(
               PortAddr iop_base
)
{
    uchar               cc_val;
    cc_val = AscGetChipControl(iop_base) & (~(CC_SINGLE_STEP | CC_TEST | CC_DIAG));
    AscSetChipControl(iop_base, (uchar) (cc_val | CC_HALT));
    AscSetChipIH(iop_base, INS_HALT);
    AscSetChipIH(iop_base, INS_RFLAG_WTM);
    if ((AscGetChipStatus(iop_base) & CSW_HALTED) == 0) {
        return (0);
    }
    return (1);
}

STATIC int
AscIsChipHalted(
                   PortAddr iop_base
)
{
    if ((AscGetChipStatus(iop_base) & CSW_HALTED) != 0) {
        if ((AscGetChipControl(iop_base) & CC_HALT) != 0) {
            return (1);
        }
    }
    return (0);
}

STATIC void
AscSetChipIH(
                PortAddr iop_base,
                ushort ins_code
)
{
    AscSetBank(iop_base, 1);
    AscWriteChipIH(iop_base, ins_code);
    AscSetBank(iop_base, 0);
    return;
}

STATIC void
AscAckInterrupt(
                   PortAddr iop_base
)
{
    uchar               host_flag;
    uchar               risc_flag;
    ushort              loop;
    loop = 0;
    do {
        risc_flag = AscReadLramByte(iop_base, ASCV_RISC_FLAG_B);
        if (loop++ > 0x7FFF) {
            break;
        }
    } while ((risc_flag & ASC_RISC_FLAG_GEN_INT) != 0);
    host_flag = AscReadLramByte(iop_base, ASCV_HOST_FLAG_B) & (~ASC_HOST_FLAG_ACK_INT);
    AscWriteLramByte(iop_base, ASCV_HOST_FLAG_B,
                     (uchar) (host_flag | ASC_HOST_FLAG_ACK_INT));
    AscSetChipStatus(iop_base, CIW_INT_ACK);
    loop = 0;
    while (AscGetChipStatus(iop_base) & CSW_INT_PENDING) {
        AscSetChipStatus(iop_base, CIW_INT_ACK);
        if (loop++ > 3) {
            break;
        }
    }
    AscWriteLramByte(iop_base, ASCV_HOST_FLAG_B, host_flag);
    return;
}

STATIC void
AscDisableInterrupt(
                       PortAddr iop_base
)
{
    ushort              cfg;
    cfg = AscGetChipCfgLsw(iop_base);
    AscSetChipCfgLsw(iop_base, cfg & (~ASC_CFG0_HOST_INT_ON));
    return;
}

STATIC void
AscEnableInterrupt(
                      PortAddr iop_base
)
{
    ushort              cfg;
    cfg = AscGetChipCfgLsw(iop_base);
    AscSetChipCfgLsw(iop_base, cfg | ASC_CFG0_HOST_INT_ON);
    return;
}



STATIC void
AscSetBank(
              PortAddr iop_base,
              uchar bank
)
{
    uchar               val;
    val = AscGetChipControl(iop_base) &
      (~(CC_SINGLE_STEP | CC_TEST | CC_DIAG | CC_SCSI_RESET | CC_CHIP_RESET));
    if (bank == 1) {
        val |= CC_BANK_ONE;
    } else if (bank == 2) {
        val |= CC_DIAG | CC_BANK_ONE;
    } else {
        val &= ~CC_BANK_ONE;
    }
    AscSetChipControl(iop_base, val);
    return;
}



STATIC int
AscResetChipAndScsiBus(
                          PortAddr iop_base
)
{
    while (AscGetChipStatus(iop_base) & CSW_SCSI_RESET_ACTIVE) ;
    AscStopChip(iop_base);
    AscSetChipControl(iop_base, CC_CHIP_RESET | CC_SCSI_RESET | CC_HALT);
    DvcSleepMilliSecond(200);
    AscSetChipIH(iop_base, INS_RFLAG_WTM);
    AscSetChipIH(iop_base, INS_HALT);
    AscSetChipControl(iop_base, CC_CHIP_RESET | CC_HALT);
    AscSetChipControl(iop_base, CC_HALT);
    DvcSleepMilliSecond(200);
    AscSetChipStatus(iop_base, CIW_CLR_SCSI_RESET_INT);
    AscSetChipStatus(iop_base, 0);
    return (AscIsChipHalted(iop_base));
}

ASC_INITFUNC(
STATIC ulong
AscGetMaxDmaCount(
                     ushort bus_type
)
)
{
    if (bus_type & ASC_IS_ISA)
        return (ASC_MAX_ISA_DMA_COUNT);
    else if (bus_type & (ASC_IS_EISA | ASC_IS_VL))
        return (ASC_MAX_VL_DMA_COUNT);
    return (ASC_MAX_PCI_DMA_COUNT);
}

ASC_INITFUNC(
STATIC ushort
AscGetIsaDmaChannel(
                       PortAddr iop_base
)
)
{
    ushort              channel;
    channel = AscGetChipCfgLsw(iop_base) & 0x0003;
    if (channel == 0x03)
        return (0);
    else if (channel == 0x00)
        return (7);
    return (channel + 4);
}

ASC_INITFUNC(
STATIC ushort
AscSetIsaDmaChannel(
                       PortAddr iop_base,
                       ushort dma_channel
)
)
{
    ushort              cfg_lsw;
    uchar               value;
    if ((dma_channel >= 5) && (dma_channel <= 7)) {
        if (dma_channel == 7)
            value = 0x00;
        else
            value = dma_channel - 4;
        cfg_lsw = AscGetChipCfgLsw(iop_base) & 0xFFFC;
        cfg_lsw |= value;
        AscSetChipCfgLsw(iop_base, cfg_lsw);
        return (AscGetIsaDmaChannel(iop_base));
    }
    return (0);
}

ASC_INITFUNC(
STATIC uchar
AscSetIsaDmaSpeed(
                     PortAddr iop_base,
                     uchar speed_value
)
)
{
    speed_value &= 0x07;
    AscSetBank(iop_base, 1);
    AscWriteChipDmaSpeed(iop_base, speed_value);
    AscSetBank(iop_base, 0);
    return (AscGetIsaDmaSpeed(iop_base));
}

ASC_INITFUNC(
STATIC uchar
AscGetIsaDmaSpeed(
                     PortAddr iop_base
)
)
{
    uchar               speed_value;
    AscSetBank(iop_base, 1);
    speed_value = AscReadChipDmaSpeed(iop_base);
    speed_value &= 0x07;
    AscSetBank(iop_base, 0);
    return (speed_value);
}

ASC_INITFUNC(
STATIC ushort
AscReadPCIConfigWord(
    ASC_DVC_VAR asc_ptr_type *asc_dvc,
    ushort pci_config_offset)
)
{
    uchar       lsb, msb;

    lsb = DvcReadPCIConfigByte(asc_dvc, pci_config_offset);
    msb = DvcReadPCIConfigByte(asc_dvc, pci_config_offset + 1);
    return ((ushort) ((msb << 8) | lsb));
}

ASC_INITFUNC(
STATIC ushort 
AscInitGetConfig(
        ASC_DVC_VAR asc_ptr_type * asc_dvc
)
)
{
    ushort              warn_code;
    PortAddr            iop_base;
    ushort              PCIDeviceID;
    ushort              PCIVendorID;
    uchar               PCIRevisionID;
    uchar               prevCmdRegBits;

    warn_code = 0;
    iop_base = asc_dvc->iop_base;
    asc_dvc->init_state = ASC_INIT_STATE_BEG_GET_CFG;
    if (asc_dvc->err_code != 0) {
        return (UW_ERR);
    }
    if (asc_dvc->bus_type == ASC_IS_PCI) {
        PCIVendorID = AscReadPCIConfigWord(asc_dvc,
                                    AscPCIConfigVendorIDRegister);

        PCIDeviceID = AscReadPCIConfigWord(asc_dvc,
                                    AscPCIConfigDeviceIDRegister);

        PCIRevisionID = DvcReadPCIConfigByte(asc_dvc,
                                    AscPCIConfigRevisionIDRegister);

        if (PCIVendorID != ASC_PCI_VENDORID) {
            warn_code |= ASC_WARN_SET_PCI_CONFIG_SPACE;
        }
        prevCmdRegBits = DvcReadPCIConfigByte(asc_dvc,
                                    AscPCIConfigCommandRegister);

        if ((prevCmdRegBits & AscPCICmdRegBits_IOMemBusMaster) !=
            AscPCICmdRegBits_IOMemBusMaster) {
            DvcWritePCIConfigByte(asc_dvc,
                            AscPCIConfigCommandRegister,
                            (prevCmdRegBits |
                             AscPCICmdRegBits_IOMemBusMaster));

            if ((DvcReadPCIConfigByte(asc_dvc,
                                AscPCIConfigCommandRegister)
                 & AscPCICmdRegBits_IOMemBusMaster)
                != AscPCICmdRegBits_IOMemBusMaster) {
                warn_code |= ASC_WARN_SET_PCI_CONFIG_SPACE;
            }
        }
        if ((PCIDeviceID == ASC_PCI_DEVICEID_1200A) ||
            (PCIDeviceID == ASC_PCI_DEVICEID_1200B)) {
            DvcWritePCIConfigByte(asc_dvc,
                            AscPCIConfigLatencyTimer, 0x00);
            if (DvcReadPCIConfigByte(asc_dvc, AscPCIConfigLatencyTimer)
                != 0x00) {
                warn_code |= ASC_WARN_SET_PCI_CONFIG_SPACE;
            }
        } else if (PCIDeviceID == ASC_PCI_DEVICEID_ULTRA) {
            if (DvcReadPCIConfigByte(asc_dvc,
                                AscPCIConfigLatencyTimer) < 0x20) {
                DvcWritePCIConfigByte(asc_dvc,
                                    AscPCIConfigLatencyTimer, 0x20);

                if (DvcReadPCIConfigByte(asc_dvc,
                                    AscPCIConfigLatencyTimer) < 0x20) {
                    warn_code |= ASC_WARN_SET_PCI_CONFIG_SPACE;
                }
            }
        }
    }

    if (AscFindSignature(iop_base)) {
        warn_code |= AscInitAscDvcVar(asc_dvc);
        warn_code |= AscInitFromEEP(asc_dvc);
        asc_dvc->init_state |= ASC_INIT_STATE_END_GET_CFG;
        if (asc_dvc->scsi_reset_wait > ASC_MAX_SCSI_RESET_WAIT) {
            asc_dvc->scsi_reset_wait = ASC_MAX_SCSI_RESET_WAIT;
        }
    } else {
        asc_dvc->err_code = ASC_IERR_BAD_SIGNATURE;
    }
    return(warn_code);
}

ASC_INITFUNC(
STATIC ushort
AscInitSetConfig(
                    ASC_DVC_VAR asc_ptr_type * asc_dvc
)
)
{
    ushort              warn_code;
    warn_code = 0;
    asc_dvc->init_state |= ASC_INIT_STATE_BEG_SET_CFG;
    if (asc_dvc->err_code != 0)
        return (UW_ERR);
    if (AscFindSignature(asc_dvc->iop_base)) {
        warn_code |= AscInitFromAscDvcVar(asc_dvc);
        asc_dvc->init_state |= ASC_INIT_STATE_END_SET_CFG;
    } else {
        asc_dvc->err_code = ASC_IERR_BAD_SIGNATURE;
    }
    return (warn_code);
}

ASC_INITFUNC(
STATIC ushort
AscInitFromAscDvcVar(
                        ASC_DVC_VAR asc_ptr_type * asc_dvc
)
)
{
    PortAddr            iop_base;
    ushort              cfg_msw;
    ushort              warn_code;
    ushort              pci_device_id;
    iop_base = asc_dvc->iop_base;
    pci_device_id = asc_dvc->cfg->pci_device_id;
    warn_code = 0;
    cfg_msw = AscGetChipCfgMsw(iop_base);
    if ((cfg_msw & ASC_CFG_MSW_CLR_MASK) != 0) {
        cfg_msw &= (~(ASC_CFG_MSW_CLR_MASK));
        warn_code |= ASC_WARN_CFG_MSW_RECOVER;
        AscSetChipCfgMsw(iop_base, cfg_msw);
    }
    if ((asc_dvc->cfg->cmd_qng_enabled & asc_dvc->cfg->disc_enable) !=
        asc_dvc->cfg->cmd_qng_enabled) {
        asc_dvc->cfg->disc_enable = asc_dvc->cfg->cmd_qng_enabled;
        warn_code |= ASC_WARN_CMD_QNG_CONFLICT;
    }
    if (AscGetChipStatus(iop_base) & CSW_AUTO_CONFIG) {
        warn_code |= ASC_WARN_AUTO_CONFIG;
    }
    if ((asc_dvc->bus_type & (ASC_IS_ISA | ASC_IS_VL)) != 0) {
        if (AscSetChipIRQ(iop_base, asc_dvc->irq_no, asc_dvc->bus_type)
            != asc_dvc->irq_no) {
            asc_dvc->err_code |= ASC_IERR_SET_IRQ_NO;
        }
    }
    if (asc_dvc->bus_type & ASC_IS_PCI) {
#if CC_DISABLE_PCI_PARITY_INT
        cfg_msw &= 0xFFC0;
        AscSetChipCfgMsw(iop_base, cfg_msw);
#endif
        if ((asc_dvc->bus_type & ASC_IS_PCI_ULTRA) == ASC_IS_PCI_ULTRA) {
        } else {
            if ((pci_device_id == ASC_PCI_DEVICE_ID_REV_A) ||
                (pci_device_id == ASC_PCI_DEVICE_ID_REV_B)) {
                asc_dvc->bug_fix_cntl |= ASC_BUG_FIX_IF_NOT_DWB;
                asc_dvc->bug_fix_cntl |= ASC_BUG_FIX_ASYN_USE_SYN;
            }
        }
    } else if (asc_dvc->bus_type == ASC_IS_ISAPNP) {
        if (AscGetChipVersion(iop_base, asc_dvc->bus_type)
            == ASC_CHIP_VER_ASYN_BUG) {
            asc_dvc->bug_fix_cntl |= ASC_BUG_FIX_ASYN_USE_SYN;
        }
    }
    if (AscSetChipScsiID(iop_base, asc_dvc->cfg->chip_scsi_id) !=
        asc_dvc->cfg->chip_scsi_id) {
        asc_dvc->err_code |= ASC_IERR_SET_SCSI_ID;
    }
    if (asc_dvc->bus_type & ASC_IS_ISA) {
        AscSetIsaDmaChannel(iop_base, asc_dvc->cfg->isa_dma_channel);
        AscSetIsaDmaSpeed(iop_base, asc_dvc->cfg->isa_dma_speed);
    }
    return (warn_code);
}

ASC_INITFUNC(
STATIC ushort
AscInitAsc1000Driver(
                        ASC_DVC_VAR asc_ptr_type * asc_dvc
)
)
{
    ushort              warn_code;
    PortAddr            iop_base;
    extern ushort       _mcode_size;
    extern ulong        _mcode_chksum;
    extern uchar        _mcode_buf[];
    iop_base = asc_dvc->iop_base;
    warn_code = 0;
    if ((asc_dvc->dvc_cntl & ASC_CNTL_RESET_SCSI) &&
        !(asc_dvc->init_state & ASC_INIT_RESET_SCSI_DONE)) {
        AscResetChipAndScsiBus(iop_base);
        DvcSleepMilliSecond((ulong) ((ushort) asc_dvc->scsi_reset_wait * 1000));
    }
    asc_dvc->init_state |= ASC_INIT_STATE_BEG_LOAD_MC;
    if (asc_dvc->err_code != 0)
        return (UW_ERR);
    if (!AscFindSignature(asc_dvc->iop_base)) {
        asc_dvc->err_code = ASC_IERR_BAD_SIGNATURE;
        return (warn_code);
    }
    AscDisableInterrupt(iop_base);
    warn_code |= AscInitLram(asc_dvc);
    if (asc_dvc->err_code != 0)
        return (UW_ERR);
    if (AscLoadMicroCode(iop_base, 0, (ushort *) _mcode_buf,
                         _mcode_size) != _mcode_chksum) {
        asc_dvc->err_code |= ASC_IERR_MCODE_CHKSUM;
        return (warn_code);
    }
    warn_code |= AscInitMicroCodeVar(asc_dvc);
    asc_dvc->init_state |= ASC_INIT_STATE_END_LOAD_MC;
    AscEnableInterrupt(iop_base);
    return (warn_code);
}

ASC_INITFUNC(
STATIC ushort
AscInitAscDvcVar(
                    ASC_DVC_VAR asc_ptr_type * asc_dvc
)
)
{
    int                 i;
    PortAddr            iop_base;
    ushort              warn_code;
    uchar               chip_version;
    iop_base = asc_dvc->iop_base;
    warn_code = 0;
    asc_dvc->err_code = 0;
    if ((asc_dvc->bus_type &
         (ASC_IS_ISA | ASC_IS_PCI | ASC_IS_EISA | ASC_IS_VL)) == 0) {
        asc_dvc->err_code |= ASC_IERR_NO_BUS_TYPE;
    }
    AscSetChipControl(iop_base, CC_HALT);
    AscSetChipStatus(iop_base, 0);
    asc_dvc->bug_fix_cntl = 0;
    asc_dvc->pci_fix_asyn_xfer = 0;
    asc_dvc->pci_fix_asyn_xfer_always = 0;
    asc_dvc->init_state = 0;
    asc_dvc->sdtr_done = 0;
    asc_dvc->cur_total_qng = 0;
    asc_dvc->is_in_int = 0;
    asc_dvc->in_critical_cnt = 0;
    asc_dvc->last_q_shortage = 0;
    asc_dvc->use_tagged_qng = 0;
    asc_dvc->no_scam = 0;
    asc_dvc->unit_not_ready = 0;
    asc_dvc->queue_full_or_busy = 0;
    asc_dvc->redo_scam = 0 ;
    asc_dvc->res2 = 0 ;
    asc_dvc->host_init_sdtr_index = 0 ;
    asc_dvc->res7 = 0 ;
    asc_dvc->res8 = 0 ;
    asc_dvc->cfg->can_tagged_qng = 0 ;
    asc_dvc->cfg->cmd_qng_enabled = 0;
    asc_dvc->dvc_cntl = ASC_DEF_DVC_CNTL;
    asc_dvc->init_sdtr = ASC_SCSI_WIDTH_BIT_SET;
    asc_dvc->max_total_qng = ASC_DEF_MAX_TOTAL_QNG;
    asc_dvc->scsi_reset_wait = 3;
    asc_dvc->start_motor = ASC_SCSI_WIDTH_BIT_SET;
    asc_dvc->max_dma_count = AscGetMaxDmaCount(asc_dvc->bus_type);
    asc_dvc->cfg->disc_enable = ASC_SCSI_WIDTH_BIT_SET;
    asc_dvc->cfg->chip_scsi_id = ASC_DEF_CHIP_SCSI_ID;
    asc_dvc->cfg->lib_serial_no = ASC_LIB_SERIAL_NUMBER;
    asc_dvc->cfg->lib_version = (ASC_LIB_VERSION_MAJOR << 8) |
      ASC_LIB_VERSION_MINOR;
    chip_version = AscGetChipVersion(iop_base, asc_dvc->bus_type);
    asc_dvc->cfg->chip_version = chip_version;
    asc_dvc->sdtr_period_tbl[0] = SYN_XFER_NS_0;
    asc_dvc->sdtr_period_tbl[1] = SYN_XFER_NS_1;
    asc_dvc->sdtr_period_tbl[2] = SYN_XFER_NS_2;
    asc_dvc->sdtr_period_tbl[3] = SYN_XFER_NS_3;
    asc_dvc->sdtr_period_tbl[4] = SYN_XFER_NS_4;
    asc_dvc->sdtr_period_tbl[5] = SYN_XFER_NS_5;
    asc_dvc->sdtr_period_tbl[6] = SYN_XFER_NS_6;
    asc_dvc->sdtr_period_tbl[7] = SYN_XFER_NS_7;
    asc_dvc->max_sdtr_index = 7;
    if ((asc_dvc->bus_type & ASC_IS_PCI) &&
        (chip_version >= ASC_CHIP_VER_PCI_ULTRA_3150)) {
        asc_dvc->bus_type = ASC_IS_PCI_ULTRA;
        asc_dvc->sdtr_period_tbl[0] = SYN_ULTRA_XFER_NS_0;
        asc_dvc->sdtr_period_tbl[1] = SYN_ULTRA_XFER_NS_1;
        asc_dvc->sdtr_period_tbl[2] = SYN_ULTRA_XFER_NS_2;
        asc_dvc->sdtr_period_tbl[3] = SYN_ULTRA_XFER_NS_3;
        asc_dvc->sdtr_period_tbl[4] = SYN_ULTRA_XFER_NS_4;
        asc_dvc->sdtr_period_tbl[5] = SYN_ULTRA_XFER_NS_5;
        asc_dvc->sdtr_period_tbl[6] = SYN_ULTRA_XFER_NS_6;
        asc_dvc->sdtr_period_tbl[7] = SYN_ULTRA_XFER_NS_7;
        asc_dvc->sdtr_period_tbl[8] = SYN_ULTRA_XFER_NS_8;
        asc_dvc->sdtr_period_tbl[9] = SYN_ULTRA_XFER_NS_9;
        asc_dvc->sdtr_period_tbl[10] = SYN_ULTRA_XFER_NS_10;
        asc_dvc->sdtr_period_tbl[11] = SYN_ULTRA_XFER_NS_11;
        asc_dvc->sdtr_period_tbl[12] = SYN_ULTRA_XFER_NS_12;
        asc_dvc->sdtr_period_tbl[13] = SYN_ULTRA_XFER_NS_13;
        asc_dvc->sdtr_period_tbl[14] = SYN_ULTRA_XFER_NS_14;
        asc_dvc->sdtr_period_tbl[15] = SYN_ULTRA_XFER_NS_15;
        asc_dvc->max_sdtr_index = 15;
        if (chip_version == ASC_CHIP_VER_PCI_ULTRA_3150)
        {
            AscSetExtraControl(iop_base,
                (SEC_ACTIVE_NEGATE | SEC_SLEW_RATE));
        } else if (chip_version >= ASC_CHIP_VER_PCI_ULTRA_3050) {
            AscSetExtraControl(iop_base,
                (SEC_ACTIVE_NEGATE | SEC_ENABLE_FILTER));
        }
    }
    if (asc_dvc->bus_type == ASC_IS_PCI) {
           AscSetExtraControl(iop_base, (SEC_ACTIVE_NEGATE | SEC_SLEW_RATE));
    }

    asc_dvc->cfg->isa_dma_speed = ASC_DEF_ISA_DMA_SPEED;
    if (AscGetChipBusType(iop_base) == ASC_IS_ISAPNP) {
        AscSetChipIFC(iop_base, IFC_INIT_DEFAULT);
        asc_dvc->bus_type = ASC_IS_ISAPNP;
    }
    if ((asc_dvc->bus_type & ASC_IS_ISA) != 0) {
        asc_dvc->cfg->isa_dma_channel = (uchar) AscGetIsaDmaChannel(iop_base);
    }
    for (i = 0; i <= ASC_MAX_TID; i++) {
        asc_dvc->cur_dvc_qng[i] = 0;
        asc_dvc->max_dvc_qng[i] = ASC_MAX_SCSI1_QNG;
        asc_dvc->scsiq_busy_head[i] = (ASC_SCSI_Q *) 0L;
        asc_dvc->scsiq_busy_tail[i] = (ASC_SCSI_Q *) 0L;
        asc_dvc->cfg->max_tag_qng[i] = ASC_MAX_INRAM_TAG_QNG;
    }
    return (warn_code);
}

#if CC_INCLUDE_EEP_CONFIG
ASC_INITFUNC(
STATIC ushort
AscInitFromEEP(
                  ASC_DVC_VAR asc_ptr_type * asc_dvc
)
)
{
    ASCEEP_CONFIG       eep_config_buf;
    ASCEEP_CONFIG *eep_config;
    PortAddr            iop_base;
    ushort              chksum;
    ushort              warn_code;
    ushort              cfg_msw, cfg_lsw;
    int                 i;
    iop_base = asc_dvc->iop_base;
    warn_code = 0;
    AscWriteLramWord(iop_base, ASCV_HALTCODE_W, 0x00FE);
    AscStopQueueExe(iop_base);
    if ((AscStopChip(iop_base) == FALSE) ||
        (AscGetChipScsiCtrl(iop_base) != 0)) {
        asc_dvc->init_state |= ASC_INIT_RESET_SCSI_DONE;
        AscResetChipAndScsiBus(iop_base);
        DvcSleepMilliSecond((ulong) ((ushort) asc_dvc->scsi_reset_wait * 1000));
    }
    if (AscIsChipHalted(iop_base) == FALSE) {
        asc_dvc->err_code |= ASC_IERR_START_STOP_CHIP;
        return (warn_code);
    }
    AscSetPCAddr(iop_base, ASC_MCODE_START_ADDR);
    if (AscGetPCAddr(iop_base) != ASC_MCODE_START_ADDR) {
        asc_dvc->err_code |= ASC_IERR_SET_PC_ADDR;
        return (warn_code);
    }
    eep_config = (ASCEEP_CONFIG *) & eep_config_buf;
    cfg_msw = AscGetChipCfgMsw(iop_base);
    cfg_lsw = AscGetChipCfgLsw(iop_base);
    if ((cfg_msw & ASC_CFG_MSW_CLR_MASK) != 0) {
        cfg_msw &= (~(ASC_CFG_MSW_CLR_MASK));
        warn_code |= ASC_WARN_CFG_MSW_RECOVER;
        AscSetChipCfgMsw(iop_base, cfg_msw);
    }
    chksum = AscGetEEPConfig(iop_base, eep_config, asc_dvc->bus_type);
    eep_config->cfg_msw &= (~(ASC_CFG_MSW_CLR_MASK));
    if (AscGetChipStatus(iop_base) & CSW_AUTO_CONFIG) {
        warn_code |= ASC_WARN_AUTO_CONFIG;
        if (asc_dvc->cfg->chip_version == 3) {
            if (eep_config->cfg_lsw != cfg_lsw) {
                warn_code |= ASC_WARN_EEPROM_RECOVER;
                eep_config->cfg_lsw = AscGetChipCfgLsw(iop_base);
            }
            if (eep_config->cfg_msw != cfg_msw) {
                warn_code |= ASC_WARN_EEPROM_RECOVER;
                eep_config->cfg_msw = AscGetChipCfgMsw(iop_base);
            }
        }
    }
    eep_config->cfg_lsw |= ASC_CFG0_HOST_INT_ON;
    if (chksum != eep_config->chksum) {
        warn_code |= ASC_WARN_EEPROM_CHKSUM;
    }
    asc_dvc->init_sdtr = eep_config->init_sdtr;
    asc_dvc->cfg->disc_enable = eep_config->disc_enable;
    asc_dvc->cfg->cmd_qng_enabled = eep_config->use_cmd_qng;
    asc_dvc->cfg->isa_dma_speed = eep_config->isa_dma_speed;
    asc_dvc->start_motor = eep_config->start_motor;
    asc_dvc->dvc_cntl = eep_config->cntl;
    asc_dvc->no_scam = eep_config->no_scam;
    if (!AscTestExternalLram(asc_dvc)) {
        if (((asc_dvc->bus_type & ASC_IS_PCI_ULTRA) == ASC_IS_PCI_ULTRA)) {
            eep_config->max_total_qng = ASC_MAX_PCI_ULTRA_INRAM_TOTAL_QNG;
            eep_config->max_tag_qng = ASC_MAX_PCI_ULTRA_INRAM_TAG_QNG;
        } else {
            eep_config->cfg_msw |= 0x0800;
            cfg_msw |= 0x0800;
            AscSetChipCfgMsw(iop_base, cfg_msw);
            eep_config->max_total_qng = ASC_MAX_PCI_INRAM_TOTAL_QNG;
            eep_config->max_tag_qng = ASC_MAX_INRAM_TAG_QNG;
        }
    } else {
    }
    if (eep_config->max_total_qng < ASC_MIN_TOTAL_QNG) {
        eep_config->max_total_qng = ASC_MIN_TOTAL_QNG;
    }
    if (eep_config->max_total_qng > ASC_MAX_TOTAL_QNG) {
        eep_config->max_total_qng = ASC_MAX_TOTAL_QNG;
    }
    if (eep_config->max_tag_qng > eep_config->max_total_qng) {
        eep_config->max_tag_qng = eep_config->max_total_qng;
    }
    if (eep_config->max_tag_qng < ASC_MIN_TAG_Q_PER_DVC) {
        eep_config->max_tag_qng = ASC_MIN_TAG_Q_PER_DVC;
    }
    asc_dvc->max_total_qng = eep_config->max_total_qng;
    if ((eep_config->use_cmd_qng & eep_config->disc_enable) !=
        eep_config->use_cmd_qng) {
        eep_config->disc_enable = eep_config->use_cmd_qng;
        warn_code |= ASC_WARN_CMD_QNG_CONFLICT;
    }
    if (asc_dvc->bus_type & (ASC_IS_ISA | ASC_IS_VL | ASC_IS_EISA)) {
        asc_dvc->irq_no = AscGetChipIRQ(iop_base, asc_dvc->bus_type);
    }
    eep_config->chip_scsi_id &= ASC_MAX_TID;
    asc_dvc->cfg->chip_scsi_id = eep_config->chip_scsi_id;
    if (((asc_dvc->bus_type & ASC_IS_PCI_ULTRA) == ASC_IS_PCI_ULTRA) &&
        !(asc_dvc->dvc_cntl & ASC_CNTL_SDTR_ENABLE_ULTRA)) {
        asc_dvc->host_init_sdtr_index = ASC_SDTR_ULTRA_PCI_10MB_INDEX;
    }

    for (i = 0; i <= ASC_MAX_TID; i++) {
#if CC_TMP_USE_EEP_SDTR
        asc_dvc->cfg->sdtr_period_offset[i] = eep_config->dos_int13_table[i];
#endif
        asc_dvc->dos_int13_table[i] = eep_config->dos_int13_table[i];
        asc_dvc->cfg->max_tag_qng[i] = eep_config->max_tag_qng;
        asc_dvc->cfg->sdtr_period_offset[i] =
            (uchar) (ASC_DEF_SDTR_OFFSET |
                     (asc_dvc->host_init_sdtr_index << 4));
    }
    eep_config->cfg_msw = AscGetChipCfgMsw(iop_base);
#if CC_CHK_FIX_EEP_CONTENT
    if (AscSetEEPConfig(iop_base, eep_config, asc_dvc->bus_type) != 0) {
        asc_dvc->err_code |= ASC_IERR_WRITE_EEPROM;
    }
#endif
    return (warn_code);
}
#endif

ASC_INITFUNC(
STATIC ushort
AscInitMicroCodeVar(
                       ASC_DVC_VAR asc_ptr_type * asc_dvc
)
)
{
    int                 i;
    ushort              warn_code;
    PortAddr            iop_base;
    ulong               phy_addr;
    iop_base = asc_dvc->iop_base;
    warn_code = 0;
    for (i = 0; i <= ASC_MAX_TID; i++) {
        AscPutMCodeInitSDTRAtID(iop_base, i,
                                asc_dvc->cfg->sdtr_period_offset[i]
);
    }
    AscInitQLinkVar(asc_dvc);
    AscWriteLramByte(iop_base, ASCV_DISC_ENABLE_B,
                     asc_dvc->cfg->disc_enable);
    AscWriteLramByte(iop_base, ASCV_HOSTSCSI_ID_B,
                     ASC_TID_TO_TARGET_ID(asc_dvc->cfg->chip_scsi_id));
    if ((phy_addr = AscGetOnePhyAddr(asc_dvc,
                                 (uchar *) asc_dvc->cfg->overrun_buf,
                                     ASC_OVERRUN_BSIZE)) == 0L) {
        asc_dvc->err_code |= ASC_IERR_GET_PHY_ADDR;
    } else {
        phy_addr = (phy_addr & 0xFFFFFFF8UL) + 8;
        AscWriteLramDWord(iop_base, ASCV_OVERRUN_PADDR_D, phy_addr);
        AscWriteLramDWord(iop_base, ASCV_OVERRUN_BSIZE_D,
                          ASC_OVERRUN_BSIZE - 8);
    }
    asc_dvc->cfg->mcode_date = AscReadLramWord(iop_base,
                                               (ushort) ASCV_MC_DATE_W);
    asc_dvc->cfg->mcode_version = AscReadLramWord(iop_base,
                                                  (ushort) ASCV_MC_VER_W);
    AscSetPCAddr(iop_base, ASC_MCODE_START_ADDR);
    if (AscGetPCAddr(iop_base) != ASC_MCODE_START_ADDR) {
        asc_dvc->err_code |= ASC_IERR_SET_PC_ADDR;
        return (warn_code);
    }
    if (AscStartChip(iop_base) != 1) {
        asc_dvc->err_code |= ASC_IERR_START_STOP_CHIP;
        return (warn_code);
    }
    return (warn_code);
}

STATIC void
AscInitPollIsrCallBack(
                          ASC_DVC_VAR asc_ptr_type * asc_dvc,
                          ASC_QDONE_INFO * scsi_done_q
)
{
    ASC_SCSI_REQ_Q *scsiq_req;
    ASC_ISR_CALLBACK    asc_isr_callback;
    uchar               cp_sen_len;
    uchar               i;
    ASC_DBG(1, "AscInitPollIsrCallBack: begin\n");
    if ((scsi_done_q->d2.flag & ASC_FLAG_SCSIQ_REQ) != 0) {
        scsiq_req = (ASC_SCSI_REQ_Q *) scsi_done_q->d2.srb_ptr;
        scsiq_req->r3.done_stat = scsi_done_q->d3.done_stat;
        scsiq_req->r3.host_stat = scsi_done_q->d3.host_stat;
        scsiq_req->r3.scsi_stat = scsi_done_q->d3.scsi_stat;
        scsiq_req->r3.scsi_msg = scsi_done_q->d3.scsi_msg;
        ASC_DBG4(1, "AscInitPollIsrCallBack: done_stat %x, host_stat %x, scsi_stat %x, scsi_msg %x\n",
            scsi_done_q->d3.done_stat, scsi_done_q->d3.host_stat,
            scsi_done_q->d3.scsi_stat, scsi_done_q->d3.scsi_msg);
        if ((scsi_done_q->d3.scsi_stat == SS_CHK_CONDITION) &&
            (scsi_done_q->d3.host_stat == 0)) {
            cp_sen_len = (uchar) ASC_MIN_SENSE_LEN;
            if (scsiq_req->r1.sense_len < ASC_MIN_SENSE_LEN) {
                cp_sen_len = (uchar) scsiq_req->r1.sense_len;
            }
            for (i = 0; i < cp_sen_len; i++) {
                scsiq_req->sense[i] = scsiq_req->sense_ptr[i];
            }
        }
    } else {
        if (asc_dvc->isr_callback != 0) {
            asc_isr_callback = (ASC_ISR_CALLBACK) asc_dvc->isr_callback;
            (*asc_isr_callback) (asc_dvc, scsi_done_q);
        }
    }
    ASC_DBG(1, "AscInitPollIsrCallBack: end\n");
    return;
}

ASC_INITFUNC(
STATIC int
AscTestExternalLram(
                       ASC_DVC_VAR asc_ptr_type * asc_dvc
)
)
{
    PortAddr            iop_base;
    ushort              q_addr;
    ushort              saved_word;
    int                 sta;
    iop_base = asc_dvc->iop_base;
    sta = 0;
    q_addr = ASC_QNO_TO_QADDR(241);
    saved_word = AscReadLramWord(iop_base, q_addr);
    AscSetChipLramAddr(iop_base, q_addr);
    AscSetChipLramData(iop_base, 0x55AA);
    DvcSleepMilliSecond(10);
    AscSetChipLramAddr(iop_base, q_addr);
    if (AscGetChipLramData(iop_base) == 0x55AA) {
        sta = 1;
        AscWriteLramWord(iop_base, q_addr, saved_word);
    }
    return (sta);
}

#if CC_INCLUDE_EEP_CONFIG
ASC_INITFUNC(
STATIC int
AscWriteEEPCmdReg(
                     PortAddr iop_base,
                     uchar cmd_reg
)
)
{
    uchar               read_back;
    int                 retry;
    retry = 0;
    while (TRUE) {
        AscSetChipEEPCmd(iop_base, cmd_reg);
        DvcSleepMilliSecond(1);
        read_back = AscGetChipEEPCmd(iop_base);
        if (read_back == cmd_reg) {
            return (1);
        }
        if (retry++ > ASC_EEP_MAX_RETRY) {
            return (0);
        }
    }
}

ASC_INITFUNC(
STATIC int
AscWriteEEPDataReg(
                      PortAddr iop_base,
                      ushort data_reg
)
)
{
    ushort              read_back;
    int                 retry;
    retry = 0;
    while (TRUE) {
        AscSetChipEEPData(iop_base, data_reg);
        DvcSleepMilliSecond(1);
        read_back = AscGetChipEEPData(iop_base);
        if (read_back == data_reg) {
            return (1);
        }
        if (retry++ > ASC_EEP_MAX_RETRY) {
            return (0);
        }
    }
}

ASC_INITFUNC(
STATIC void
AscWaitEEPRead(
                  void
)
)
{
    DvcSleepMilliSecond(1);
    return;
}

ASC_INITFUNC(
STATIC void
AscWaitEEPWrite(
                   void
)
)
{
    DvcSleepMilliSecond(20);
    return;
}

ASC_INITFUNC(
STATIC ushort
AscReadEEPWord(
                  PortAddr iop_base,
                  uchar addr
)
)
{
    ushort              read_wval;
    uchar               cmd_reg;
    AscWriteEEPCmdReg(iop_base, ASC_EEP_CMD_WRITE_DISABLE);
    AscWaitEEPRead();
    cmd_reg = addr | ASC_EEP_CMD_READ;
    AscWriteEEPCmdReg(iop_base, cmd_reg);
    AscWaitEEPRead();
    read_wval = AscGetChipEEPData(iop_base);
    AscWaitEEPRead();
    return (read_wval);
}

ASC_INITFUNC(
STATIC ushort
AscWriteEEPWord(
                   PortAddr iop_base,
                   uchar addr,
                   ushort word_val
)
)
{
    ushort              read_wval;
    read_wval = AscReadEEPWord(iop_base, addr);
    if (read_wval != word_val) {
        AscWriteEEPCmdReg(iop_base, ASC_EEP_CMD_WRITE_ABLE);
        AscWaitEEPRead();
        AscWriteEEPDataReg(iop_base, word_val);
        AscWaitEEPRead();
        AscWriteEEPCmdReg(iop_base,
                          (uchar) ((uchar) ASC_EEP_CMD_WRITE | addr));
        AscWaitEEPWrite();
        AscWriteEEPCmdReg(iop_base, ASC_EEP_CMD_WRITE_DISABLE);
        AscWaitEEPRead();
        return (AscReadEEPWord(iop_base, addr));
    }
    return (read_wval);
}

ASC_INITFUNC(
STATIC ushort
AscGetEEPConfig(
                   PortAddr iop_base,
                   ASCEEP_CONFIG * cfg_buf, ushort bus_type
)
)
{
    ushort              wval;
    ushort              sum;
    ushort      *wbuf;
    int                 cfg_beg;
    int                 cfg_end;
    int                 s_addr;
    int                 isa_pnp_wsize;
    wbuf = (ushort *) cfg_buf;
    sum = 0;
    isa_pnp_wsize = 0;
    for (s_addr = 0; s_addr < (2 + isa_pnp_wsize); s_addr++, wbuf++) {
        wval = AscReadEEPWord(iop_base, (uchar) s_addr);
        sum += wval;
        *wbuf = wval;
    }
    if (bus_type & ASC_IS_VL) {
        cfg_beg = ASC_EEP_DVC_CFG_BEG_VL;
        cfg_end = ASC_EEP_MAX_DVC_ADDR_VL;
    } else {
        cfg_beg = ASC_EEP_DVC_CFG_BEG;
        cfg_end = ASC_EEP_MAX_DVC_ADDR;
    }
    for (s_addr = cfg_beg; s_addr <= (cfg_end - 1);
         s_addr++, wbuf++) {
        wval = AscReadEEPWord(iop_base, (uchar) s_addr);
        sum += wval;
        *wbuf = wval;
    }
    *wbuf = AscReadEEPWord(iop_base, (uchar) s_addr);
    return (sum);
}

#if CC_CHK_FIX_EEP_CONTENT
ASC_INITFUNC(
STATIC int
AscSetEEPConfigOnce(
                       PortAddr iop_base,
                       ASCEEP_CONFIG * cfg_buf, ushort bus_type
)
)
{
    int                 n_error;
    ushort      *wbuf;
    ushort              sum;
    int                 s_addr;
    int                 cfg_beg;
    int                 cfg_end;
    wbuf = (ushort *) cfg_buf;
    n_error = 0;
    sum = 0;
    for (s_addr = 0; s_addr < 2; s_addr++, wbuf++) {
        sum += *wbuf;
        if (*wbuf != AscWriteEEPWord(iop_base, (uchar) s_addr, *wbuf)) {
            n_error++;
        }
    }
    if (bus_type & ASC_IS_VL) {
        cfg_beg = ASC_EEP_DVC_CFG_BEG_VL;
        cfg_end = ASC_EEP_MAX_DVC_ADDR_VL;
    } else {
        cfg_beg = ASC_EEP_DVC_CFG_BEG;
        cfg_end = ASC_EEP_MAX_DVC_ADDR;
    }
    for (s_addr = cfg_beg; s_addr <= (cfg_end - 1);
         s_addr++, wbuf++) {
        sum += *wbuf;
        if (*wbuf != AscWriteEEPWord(iop_base, (uchar) s_addr, *wbuf)) {
            n_error++;
        }
    }
    *wbuf = sum;
    if (sum != AscWriteEEPWord(iop_base, (uchar) s_addr, sum)) {
        n_error++;
    }
    wbuf = (ushort *) cfg_buf;
    for (s_addr = 0; s_addr < 2; s_addr++, wbuf++) {
        if (*wbuf != AscReadEEPWord(iop_base, (uchar) s_addr)) {
            n_error++;
        }
    }
    for (s_addr = cfg_beg; s_addr <= cfg_end;
         s_addr++, wbuf++) {
        if (*wbuf != AscReadEEPWord(iop_base, (uchar) s_addr)) {
            n_error++;
        }
    }
    return (n_error);
}

ASC_INITFUNC(
STATIC int
AscSetEEPConfig(
                   PortAddr iop_base,
                   ASCEEP_CONFIG * cfg_buf, ushort bus_type
)
)
{
    int            retry;
    int            n_error;

    retry = 0;
    while (TRUE) {
        if ((n_error = AscSetEEPConfigOnce(iop_base, cfg_buf,
                                           bus_type)) == 0) {
            break;
        }
        if (++retry > ASC_EEP_MAX_RETRY) {
            break;
        }
    }
    return (n_error);
}
#endif
#endif

STATIC int
AscInitPollBegin(
                    REG ASC_DVC_VAR asc_ptr_type * asc_dvc
)
{
    PortAddr            iop_base;
    iop_base = asc_dvc->iop_base;
    AscDisableInterrupt(iop_base);
    asc_dvc->init_state |= ASC_INIT_STATE_BEG_INQUIRY;
    AscWriteLramByte(iop_base, ASCV_DISC_ENABLE_B, 0x00);
    asc_dvc->use_tagged_qng = 0;
    asc_dvc->cfg->can_tagged_qng = 0;
    asc_dvc->saved_ptr2func = (ulong) asc_dvc->isr_callback;
    asc_dvc->isr_callback = ASC_GET_PTR2FUNC(AscInitPollIsrCallBack);
    return (0);
}

STATIC int
AscInitPollEnd(
                  REG ASC_DVC_VAR asc_ptr_type * asc_dvc
)
{
    PortAddr            iop_base;
    rint                i;
    iop_base = asc_dvc->iop_base;
    asc_dvc->isr_callback = (Ptr2Func) asc_dvc->saved_ptr2func;
    AscWriteLramByte(iop_base, ASCV_DISC_ENABLE_B,
                     asc_dvc->cfg->disc_enable);
    AscWriteLramByte(iop_base, ASCV_USE_TAGGED_QNG_B,
                     asc_dvc->use_tagged_qng);
    AscWriteLramByte(iop_base, ASCV_CAN_TAGGED_QNG_B,
                     asc_dvc->cfg->can_tagged_qng);
    for (i = 0; i <= ASC_MAX_TID; i++) {
        AscWriteLramByte(iop_base,
                      (ushort) ((ushort) ASCV_MAX_DVC_QNG_BEG + (ushort) i),
                         asc_dvc->max_dvc_qng[i]);
    }
    AscAckInterrupt(iop_base);
    AscEnableInterrupt(iop_base);
    asc_dvc->init_state |= ASC_INIT_STATE_END_INQUIRY;
    return (0);
}

STATIC int                 _asc_wait_slow_device_ = FALSE;

STATIC int
AscInitPollTarget(
                     REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                     REG ASC_SCSI_REQ_Q * scsiq,
                     REG ASC_SCSI_INQUIRY * inq,
                     REG ASC_CAP_INFO * cap_info
)
{
    uchar               tid_no, lun;
    uchar               dvc_type;
    ASC_SCSI_BIT_ID_TYPE tid_bits;
    int                 dvc_found;
    int                 support_read_cap;
    int                 tmp_disable_init_sdtr;
    int                 sta;

    dvc_found = 0;
    tmp_disable_init_sdtr = FALSE;
    tid_bits = scsiq->r1.target_id;
    lun = scsiq->r1.target_lun;
    tid_no = ASC_TIX_TO_TID(scsiq->r2.target_ix);
    if (((asc_dvc->init_sdtr & tid_bits) != 0) &&
        ((asc_dvc->sdtr_done & tid_bits) == 0)) {
        asc_dvc->init_sdtr &= ~tid_bits;
        tmp_disable_init_sdtr = TRUE;
    }
    ASC_DBG(1, "AscInitPollTarget: before PollScsiInquiry\n");
    if (PollScsiInquiry(asc_dvc, scsiq, (uchar *) inq,
        sizeof (ASC_SCSI_INQUIRY)) == 1) {
        dvc_found = 1;
        support_read_cap = TRUE;
        dvc_type = inq->byte0.peri_dvc_type;
        if (dvc_type != SCSI_TYPE_UNKNOWN) {
            if ((dvc_type != SCSI_TYPE_DASD)
                && (dvc_type != SCSI_TYPE_WORM)
                && (dvc_type != SCSI_TYPE_CDROM)
                && (dvc_type != SCSI_TYPE_OPTMEM)) {
                asc_dvc->start_motor &= ~tid_bits;
                support_read_cap = FALSE;
            }
            if ((dvc_type != SCSI_TYPE_DASD) || inq->byte1.rmb) {
                if (!_asc_wait_slow_device_) {
                    DvcSleepMilliSecond(3000 - ((int) tid_no * 250));
                    _asc_wait_slow_device_ = TRUE;
                }
            }
            if (lun == 0) {
                if ((inq->byte3.rsp_data_fmt >= 2) ||
                    (inq->byte2.ansi_apr_ver >= 2)) {
                    if (inq->byte7.CmdQue) {
                        asc_dvc->cfg->can_tagged_qng |= tid_bits;
                        if (asc_dvc->cfg->cmd_qng_enabled & tid_bits) {
                                asc_dvc->use_tagged_qng |= tid_bits;
                                asc_dvc->max_dvc_qng[tid_no] = asc_dvc->cfg->max_tag_qng[tid_no];
                        }
                    }
                    if (!inq->byte7.Sync) {
                        asc_dvc->init_sdtr &= ~tid_bits;
                        asc_dvc->sdtr_done &= ~tid_bits;
                    } else if (tmp_disable_init_sdtr) {
                        asc_dvc->init_sdtr |= tid_bits;
                    }
                } else {
                    asc_dvc->init_sdtr &= ~tid_bits;
                    asc_dvc->sdtr_done &= ~tid_bits;
                    asc_dvc->use_tagged_qng &= ~tid_bits;
                }
            }
            if (asc_dvc->bug_fix_cntl & ASC_BUG_FIX_ASYN_USE_SYN) {
                if (!(asc_dvc->init_sdtr & tid_bits)) {
                    if ((dvc_type == SCSI_TYPE_CDROM) &&
                        (AscCompareString((uchar *) inq->vendor_id,
                            (uchar *) "HP ", 3) == 0)) {
                        asc_dvc->pci_fix_asyn_xfer_always |= tid_bits;
                    }
                    asc_dvc->pci_fix_asyn_xfer |= tid_bits;
                    if ((dvc_type == SCSI_TYPE_PROC) || (dvc_type == SCSI_TYPE_SCANNER)) {
                        asc_dvc->pci_fix_asyn_xfer &= ~tid_bits;
                    }
                    if ((dvc_type == SCSI_TYPE_SASD) &&
                        (AscCompareString((uchar *) inq->vendor_id,
                            (uchar *) "TANDBERG", 8) == 0) &&
                        (AscCompareString((uchar *) inq->product_id,
                         (uchar *) " TDC 36", 7) == 0)) {
                        asc_dvc->pci_fix_asyn_xfer &= ~tid_bits;
                    }
                    if ((dvc_type == SCSI_TYPE_SASD) &&
                        (AscCompareString((uchar *) inq->vendor_id,
                         (uchar *) "WANGTEK ", 8) == 0)) {
                        asc_dvc->pci_fix_asyn_xfer &= ~tid_bits;
                    }

                    if ((dvc_type == SCSI_TYPE_CDROM) &&
                       (AscCompareString((uchar *)inq->vendor_id,
                        (uchar *)"NEC     ", 8) == 0) &&
                        (AscCompareString((uchar *)inq->product_id,
                         (uchar *)"CD-ROM DRIVE    ", 16) == 0)) {
                        asc_dvc->pci_fix_asyn_xfer &= ~tid_bits ;
                    }
 
                    if (asc_dvc->pci_fix_asyn_xfer & tid_bits) {
                        AscSetRunChipSynRegAtID(asc_dvc->iop_base, tid_no,
                                                ASYN_SDTR_DATA_FIX_PCI_REV_AB);
                    }
                }
            }
            sta = 1;
            ASC_DBG(1, "AscInitPollTarget: before InitTestUnitReady\n");
            sta = InitTestUnitReady(asc_dvc, scsiq);
            if (sta == 1) {
                if ((cap_info != 0L) && support_read_cap) {
                    ASC_DBG(1,
                        "AscInitPollTarget: before PollScsiReadCapacity\n");
                    if (PollScsiReadCapacity(asc_dvc, scsiq,
                                             cap_info) != 1) {
                        cap_info->lba = 0L;
                        cap_info->blk_size = 0x0000;
                    } else {
                    }
                }
            }
        } else {
            asc_dvc->start_motor &= ~tid_bits;
        }
    } else if (tmp_disable_init_sdtr) {
        asc_dvc->init_sdtr |= tid_bits;
    }
    ASC_DBG1(1, "AscInitPollTarget: dvc_found %d\n", dvc_found);
    return (dvc_found);
}

STATIC int
PollQueueDone(
                 REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                 REG ASC_SCSI_REQ_Q * scsiq,
                 int timeout_sec
)
{
    int                 status;
    int                 retry = 0;

    ASC_DBG1(1, "PollQueueDone: timeout_sec %d\n", timeout_sec);
    do {
        ASC_DBG(1, "PollQueueDone: before AscExeScsiQueue\n");
        if ((status = AscExeScsiQueue(asc_dvc,
                (ASC_SCSI_Q *) scsiq)) == 1) {
            ASC_DBG(1, "PollQueueDone: before AscPollQDone\n");
            if ((status = AscPollQDone(asc_dvc, scsiq,
                                       timeout_sec)) != 1) {
                ASC_DBG1(1, "PollQueueDone: status %x\n", status);
                if (status == 0x80) {
                    if (retry++ > ASC_MAX_INIT_BUSY_RETRY) {
                        break;
                    }
                    scsiq->r3.done_stat = 0;
                    scsiq->r3.host_stat = 0;
                    scsiq->r3.scsi_stat = 0;
                    scsiq->r3.scsi_msg = 0;
                    DvcSleepMilliSecond(2000);
                    continue;
                }
                scsiq->r3.done_stat = 0;
                scsiq->r3.host_stat = 0;
                scsiq->r3.scsi_stat = 0;
                scsiq->r3.scsi_msg = 0;
                ASC_DBG(1, "PollQueueDone: before AscAbortSRB()\n");
                AscAbortSRB(asc_dvc, (ulong) scsiq);
            }
            ASC_DBG1(1, "PollQueueDone: status %x\n", status);
            ASC_DBG1(1, "PollQueueDone: done_stat %x\n", scsiq->r3.done_stat);
            return (scsiq->r3.done_stat);
        }
        ASC_DBG1(1, "PollQueueDone: status %x\n", status);
        DvcSleepMilliSecond(5);
    } while (((status == 0) || (status == 0x80)) &&
              retry++ < ASC_MAX_INIT_BUSY_RETRY);
    ASC_DBG1(1, "PollQueueDone: status %x\n", status);
    ASC_DBG(1, "PollQueueDone: done_stat QD_WITH_ERROR\n");
    return (scsiq->r3.done_stat = QD_WITH_ERROR);
}

STATIC int
PollScsiInquiry(
                   REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                   REG ASC_SCSI_REQ_Q * scsiq,
                   uchar * buf,
                   int buf_len
)
{
    if (AscScsiInquiry(asc_dvc, scsiq, buf, buf_len) == ERR) {
        return (scsiq->r3.done_stat = QD_WITH_ERROR);
    }
    return (PollQueueDone(asc_dvc, (ASC_SCSI_REQ_Q *) scsiq, 4));
}

STATIC int
PollScsiStartUnit(
                     REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                     REG ASC_SCSI_REQ_Q * scsiq
)
{
    if (AscScsiStartStopUnit(asc_dvc, scsiq, 1) == ERR) {
        return (scsiq->r3.done_stat = QD_WITH_ERROR);
    }
    return (PollQueueDone(asc_dvc, (ASC_SCSI_REQ_Q *) scsiq, 40));
}

STATIC int
PollScsiReadCapacity(
                        REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                        REG ASC_SCSI_REQ_Q * scsiq,
                        REG ASC_CAP_INFO * cap_info
)
{
    ASC_CAP_INFO        scsi_cap_info;
    int                 status;
    if (AscScsiReadCapacity(asc_dvc, scsiq,
                            (uchar *) & scsi_cap_info) == ERR) {
        return (scsiq->r3.done_stat = QD_WITH_ERROR);
    }
    status = PollQueueDone(asc_dvc, (ASC_SCSI_REQ_Q *) scsiq, 8);
    if (status == 1) {
#if CC_LITTLE_ENDIAN_HOST
        cap_info->lba = (ulong) * swapfarbuf4((uchar *) & scsi_cap_info.lba);
        cap_info->blk_size = (ulong) * swapfarbuf4((uchar *) & scsi_cap_info.blk_size);
#else
        cap_info->lba = scsi_cap_info.lba;
        cap_info->blk_size = scsi_cap_info.blk_size;
#endif
        return (scsiq->r3.done_stat);
    }
    return (scsiq->r3.done_stat = QD_WITH_ERROR);
}

STATIC ulong *
swapfarbuf4(
    uchar *buf
)
{
    uchar      tmp;

    tmp = buf[3];
    buf[3] = buf[0];
    buf[0] = tmp;

    tmp = buf[1];
    buf[1] = buf[2];
    buf[2] = tmp;

    return ((ulong *) buf);
}

STATIC int
PollScsiTestUnitReady(
                         REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                         REG ASC_SCSI_REQ_Q * scsiq
)
{
    if (AscScsiTestUnitReady(asc_dvc, scsiq) == ERR) {
        return (scsiq->r3.done_stat = QD_WITH_ERROR);
    }
    return (PollQueueDone(asc_dvc, (ASC_SCSI_REQ_Q *) scsiq, 12));
}

STATIC int
InitTestUnitReady(
                     REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                     REG ASC_SCSI_REQ_Q * scsiq
)
{
    ASC_SCSI_BIT_ID_TYPE tid_bits;
    int                 retry;
    ASC_REQ_SENSE *sen;
    retry = 0;
    tid_bits = scsiq->r1.target_id;
    while (retry++ < 4) {
        PollScsiTestUnitReady(asc_dvc, scsiq);
        if (scsiq->r3.done_stat == 0x01) {
            return (1);
        } else if (scsiq->r3.done_stat == QD_WITH_ERROR) {
            DvcSleepMilliSecond(200);
            sen = (ASC_REQ_SENSE *) scsiq->sense_ptr;
            if ((scsiq->r3.scsi_stat == SS_CHK_CONDITION) &&
                ((sen->err_code & 0x70) != 0)) {
                if (sen->sense_key == SCSI_SENKEY_NOT_READY) {
                    if (asc_dvc->start_motor & tid_bits) {
                        if (PollScsiStartUnit(asc_dvc, scsiq) == 1) {
                            retry = 0;
                            continue;
                        } else {
                            asc_dvc->start_motor &= ~tid_bits;
                            break;
                        }
                    } else {
                        DvcSleepMilliSecond(5000);
                    }
                } else if (sen->sense_key == SCSI_SENKEY_ATTENTION) {
                    DvcSleepMilliSecond((ulong)(500L*retry)) ;
                } else {
                    DvcSleepMilliSecond(500) ;
                    break;
                }
            } else {
                break;
            }
        } else if (scsiq->r3.done_stat == QD_ABORTED_BY_HOST) {
            break;
        } else {
            break;
        }
    }
    return (0);
}

STATIC int
AscPollQDone(
                REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                REG ASC_SCSI_REQ_Q * scsiq,
                int timeout_sec
)
{
    int                 loop, loop_end;
    int                 sta;
    PortAddr            iop_base;
    iop_base = asc_dvc->iop_base;
    loop = 0;
    loop_end = timeout_sec * 100;
    sta = 1;
    while (TRUE) {
        if (asc_dvc->err_code != 0) {
            scsiq->r3.done_stat = QD_WITH_ERROR;
            ASC_DBG1(1, "AscPollQDone: err_code %x\n", asc_dvc->err_code);
            sta = ERR;
            break;
        }
        if (scsiq->r3.done_stat != QD_IN_PROGRESS) {
            if ((scsiq->r3.done_stat == QD_WITH_ERROR) &&
                (scsiq->r3.scsi_stat == SS_TARGET_BUSY)) {
                sta = 0x80;
            }
            break;
        }
        DvcSleepMilliSecond(10);
        if (loop++ > loop_end) {
            ASC_DBG(1, "AscPollQDone: loop finished\n");
            sta = 0;
            break;
        }
        if (AscIsChipHalted(iop_base)) {
            ASC_DBG(1, "AscPollQDone: AscIsChipHalted()\n");
#if !CC_ASCISR_CHECK_INT_PENDING
            AscAckInterrupt(iop_base);
#endif
            AscISR(asc_dvc);
            loop = 0;
        } else {
            if (AscIsIntPending(iop_base)) {
                ASC_DBG(1, "AscPollQDone: AscIsIntPending()\n");
#if !CC_ASCISR_CHECK_INT_PENDING
                AscAckInterrupt(iop_base);
#endif
                AscISR(asc_dvc);
            }
        }
    }
    return (sta);
}

STATIC int
AscCompareString(
                    ruchar * str1,
                    ruchar * str2,
                    int len
)
{
    int                 i;
    int                 diff;
    for (i = 0; i < len; i++) {
        diff = (int) (str1[i] - str2[i]);
        if (diff != 0)
            return (diff);
    }
    return (0);
}

STATIC uchar
AscReadLramByte(
                   PortAddr iop_base,
                   ushort addr
)
{
    uchar               byte_data;
    ushort              word_data;
    if (isodd_word(addr)) {
        AscSetChipLramAddr(iop_base, addr - 1);
        word_data = AscGetChipLramData(iop_base);
        byte_data = (uchar) ((word_data >> 8) & 0xFF);
    } else {
        AscSetChipLramAddr(iop_base, addr);
        word_data = AscGetChipLramData(iop_base);
        byte_data = (uchar) (word_data & 0xFF);
    }
    return (byte_data);
}

STATIC ushort
AscReadLramWord(
                   PortAddr iop_base,
                   ushort addr
)
{
    ushort              word_data;
    AscSetChipLramAddr(iop_base, addr);
    word_data = AscGetChipLramData(iop_base);
    return (word_data);
}

STATIC ulong
AscReadLramDWord(
                    PortAddr iop_base,
                    ushort addr
)
{
    ushort              val_low, val_high;
    ulong               dword_data;
    AscSetChipLramAddr(iop_base, addr);
    val_low = AscGetChipLramData(iop_base);
    val_high = AscGetChipLramData(iop_base);
    dword_data = ((ulong) val_high << 16) | (ulong) val_low;
    return (dword_data);
}

STATIC void
AscWriteLramWord(
                    PortAddr iop_base,
                    ushort addr,
                    ushort word_val
)
{
    AscSetChipLramAddr(iop_base, addr);
    AscSetChipLramData(iop_base, word_val);
    return;
}

STATIC void
AscWriteLramDWord(
                     PortAddr iop_base,
                     ushort addr,
                     ulong dword_val
)
{
    ushort              word_val;
    AscSetChipLramAddr(iop_base, addr);
    word_val = (ushort) dword_val;
    AscSetChipLramData(iop_base, word_val);
    word_val = (ushort) (dword_val >> 16);
    AscSetChipLramData(iop_base, word_val);
    return;
}

STATIC void
AscWriteLramByte(
                    PortAddr iop_base,
                    ushort addr,
                    uchar byte_val
)
{
    ushort              word_data;
    if (isodd_word(addr)) {
        addr--;
        word_data = AscReadLramWord(iop_base, addr);
        word_data &= 0x00FF;
        word_data |= (((ushort) byte_val << 8) & 0xFF00);
    } else {
        word_data = AscReadLramWord(iop_base, addr);
        word_data &= 0xFF00;
        word_data |= ((ushort) byte_val & 0x00FF);
    }
    AscWriteLramWord(iop_base, addr, word_data);
    return;
}

STATIC void
AscMemWordCopyToLram(
                        PortAddr iop_base,
                        ushort s_addr,
                        ushort * s_buffer,
                        int words
)
{
    AscSetChipLramAddr(iop_base, s_addr);
    DvcOutPortWords(iop_base + IOP_RAM_DATA, s_buffer, words);
    return;
}

STATIC void
AscMemDWordCopyToLram(
                         PortAddr iop_base,
                         ushort s_addr,
                         ulong * s_buffer,
                         int dwords
)
{
    AscSetChipLramAddr(iop_base, s_addr);
    DvcOutPortDWords(iop_base + IOP_RAM_DATA, s_buffer, dwords);
    return;
}

STATIC void
AscMemWordCopyFromLram(
                          PortAddr iop_base,
                          ushort s_addr,
                          ushort * d_buffer,
                          int words
)
{
    AscSetChipLramAddr(iop_base, s_addr);
    DvcInPortWords(iop_base + IOP_RAM_DATA, d_buffer, words);
    return;
}

STATIC ulong
AscMemSumLramWord(
                     PortAddr iop_base,
                     ushort s_addr,
                     rint words
)
{
    ulong               sum;
    int                 i;
    sum = 0L;
    for (i = 0; i < words; i++, s_addr += 2) {
        sum += AscReadLramWord(iop_base, s_addr);
    }
    return (sum);
}

STATIC void
AscMemWordSetLram(
                     PortAddr iop_base,
                     ushort s_addr,
                     ushort set_wval,
                     rint words
)
{
    rint             i;
    AscSetChipLramAddr(iop_base, s_addr);
    for (i = 0; i < words; i++) {
        AscSetChipLramData(iop_base, set_wval);
    }
    return;
}


STATIC int
AscScsiInquiry(
                  REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                  REG ASC_SCSI_REQ_Q * scsiq,
                  uchar * buf,
                  int buf_len
)
{
    if (AscScsiSetupCmdQ(asc_dvc, scsiq, buf,
                         (ulong) buf_len) == ERR) {
        return (scsiq->r3.done_stat = QD_WITH_ERROR);
    }
    scsiq->cdb[0] = (uchar) SCSICMD_Inquiry;
    scsiq->cdb[1] = scsiq->r1.target_lun << 5;
    scsiq->cdb[2] = 0;
    scsiq->cdb[3] = 0;
    scsiq->cdb[4] = buf_len;
    scsiq->cdb[5] = 0;
    scsiq->r2.cdb_len = 6;
    return (0);
}

STATIC int
AscScsiReadCapacity(
                       REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                       REG ASC_SCSI_REQ_Q * scsiq,
                       uchar * info
)
{
    if (AscScsiSetupCmdQ(asc_dvc, scsiq, info, 8L) == ERR) {
        return (scsiq->r3.done_stat = QD_WITH_ERROR);
    }
    scsiq->cdb[0] = (uchar) SCSICMD_ReadCapacity;
    scsiq->cdb[1] = scsiq->r1.target_lun << 5;
    scsiq->cdb[2] = 0;
    scsiq->cdb[3] = 0;
    scsiq->cdb[4] = 0;
    scsiq->cdb[5] = 0;
    scsiq->cdb[6] = 0;
    scsiq->cdb[7] = 0;
    scsiq->cdb[8] = 0;
    scsiq->cdb[9] = 0;
    scsiq->r2.cdb_len = 10;
    return (0);
}

STATIC int
AscScsiTestUnitReady(
                        REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                        REG ASC_SCSI_REQ_Q * scsiq
)
{
    if (AscScsiSetupCmdQ(asc_dvc, scsiq, FNULLPTR,
                         (ulong) 0L) == ERR) {
        return (scsiq->r3.done_stat = QD_WITH_ERROR);
    }
    scsiq->r1.cntl = (uchar) ASC_SCSIDIR_NODATA;
    scsiq->cdb[0] = (uchar) SCSICMD_TestUnitReady;
    scsiq->cdb[1] = scsiq->r1.target_lun << 5;
    scsiq->cdb[2] = 0;
    scsiq->cdb[3] = 0;
    scsiq->cdb[4] = 0;
    scsiq->cdb[5] = 0;
    scsiq->r2.cdb_len = 6;
    return (0);
}

STATIC int
AscScsiStartStopUnit(
                        REG ASC_DVC_VAR asc_ptr_type * asc_dvc,
                        REG ASC_SCSI_REQ_Q * scsiq,
                        uchar op_mode
)
{
    if (AscScsiSetupCmdQ(asc_dvc, scsiq, FNULLPTR, (ulong) 0L) == ERR) {
        return (scsiq->r3.done_stat = QD_WITH_ERROR);
    }
    scsiq->r1.cntl = (uchar) ASC_SCSIDIR_NODATA;
    scsiq->cdb[0] = (uchar) SCSICMD_StartStopUnit;
    scsiq->cdb[1] = scsiq->r1.target_lun << 5;
    scsiq->cdb[2] = 0;
    scsiq->cdb[3] = 0;
    scsiq->cdb[4] = op_mode;
    scsiq->cdb[5] = 0;
    scsiq->r2.cdb_len = 6;
    return (0);
}