1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
|
/* blz1230.h: Defines and structures for the Blizzard 1230 SCSI IV driver.
*
* Copyright (C) 1996 Jesper Skov (jskov@cygnus.co.uk)
*
* This file is based on cyber_esp.h (hence the occasional reference to
* CyberStorm).
*/
#include "NCR53C9x.h"
#ifndef BLZ1230_H
#define BLZ1230_H
/* The controller registers can be found in the Z2 config area at these
* offsets:
*/
#define BLZ1230_ESP_ADDR 0x8000
#define BLZ1230_DMA_ADDR 0x10000
#define BLZ1230II_ESP_ADDR 0x10000
#define BLZ1230II_DMA_ADDR 0x10021
/* The Blizzard 1230 DMA interface
* ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
* Only two things can be programmed in the Blizzard DMA:
* 1) The data direction is controlled by the status of bit 31 (1 = write)
* 2) The source/dest address (word aligned, shifted one right) in bits 30-0
*
* Program DMA by first latching the highest byte of the address/direction
* (i.e. bits 31-24 of the long word constructed as described in steps 1+2
* above). Then write each byte of the address/direction (starting with the
* top byte, working down) to the DMA address register.
*
* Figure out interrupt status by reading the ESP status byte.
*/
struct blz1230_dma_registers {
volatile unsigned char dma_addr; /* DMA address [0x0000] */
unsigned char dmapad2[0x7fff];
volatile unsigned char dma_latch; /* DMA latch [0x8000] */
};
struct blz1230II_dma_registers {
volatile unsigned char dma_addr; /* DMA address [0x0000] */
unsigned char dmapad2[0xf];
volatile unsigned char dma_latch; /* DMA latch [0x0010] */
};
#define BLZ1230_DMA_WRITE 0x80000000
extern int blz1230_esp_detect(struct SHT *);
extern int blz1230_esp_release(struct Scsi_Host *);
extern const char *esp_info(struct Scsi_Host *);
extern int esp_queue(Scsi_Cmnd *, void (*done)(Scsi_Cmnd *));
extern int esp_command(Scsi_Cmnd *);
extern int esp_abort(Scsi_Cmnd *);
extern int esp_reset(Scsi_Cmnd *, unsigned int);
extern int esp_proc_info(char *buffer, char **start, off_t offset, int length,
int hostno, int inout);
#define SCSI_BLZ1230 { proc_dir: &proc_scsi_esp, \
proc_info: esp_proc_info, \
name: "Blizzard1230 SCSI IV", \
detect: blz1230_esp_detect, \
release: blz1230_esp_release, \
command: esp_command, \
queuecommand: esp_queue, \
abort: esp_abort, \
reset: esp_reset, \
can_queue: 7, \
this_id: 7, \
sg_tablesize: SG_ALL, \
cmd_per_lun: 1, \
use_clustering: ENABLE_CLUSTERING }
#endif /* BLZ1230_H */
|
